Stanley SFMCE520 User manual

Brand: Stanley

Model: SFMCE520

Category: Car battery chargers

Type: User manual

Stanley SFMCE520 is a versatile and powerful inflation station designed for a wide range of inflation tasks, from car and bike tires to balls, rafts, air mattresses, and more. With its high-volume hose and tapered nozzle, it can quickly and easily inflate large volume items. For high-pressure applications, the included high-pressure hose and brass coupler adapter provide the necessary precision and control. Additionally, the inflator features a digital readout and pressure setting buttons, allowing you to monitor and adjust the pressure to the desired level.

SFMCE520

1 6 8 7 10

4 11

12 14

1517

ENGLISH

(Original instructions)

25b

25a

21a

ENGLISH

(Original instructions)

Intended use

Your STANLEY FATMAX SFMCE520 Ination station has

been designed to be used in most vehicles from the standard

12 Volt socket to inate car and bike tyres, balls, rafts, air mat-

tresses, swimming pool oats, etc. This appliances is intended

for professional and private, non professional users.

Read all of this manual carefully

before operating the appliance.

Safety instructions

Warning! Read all safety

warnings and all instructions

Failure to follow the warnings

and instructions listed below may

result in electric shock, re and/or

serious injury.

u The intended use is described in this

manual. The use of any accessory

or attachment or the performance

of any operation with this appliance

other than those recommended in this

instruction manual may present a risk

of personal injury.

u Retain this manual for future

reference.

72411

Using your appliance

u Do not use the appliance to pick up

liquids or any materials that could

catch re.

u Do not immerse the appliance in water.

u Never pull the charger lead to

disconnect the charger from the

socket. Keep the charger lead away

from heat, oil and sharp edges.

u If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualied

persons in order to avoid a hazard.

Safety of others

u The appliance is not to be used by

persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction.

u Children being supervised not to play

with the appliance.

Inspection and repairs

Before use, check the appliance for dam-

aged or defective parts.

Check for breakage of parts, damage to

switches and any other conditions that

may affect its operation.

u Do not use the appliance if any part is

damaged or defective.

u Have any damaged or defective parts

repaired or replaced by an authorized

repair agent.

u Regularly check the charger lead for

damage.

Replace the charger if the lead is

ENGLISH

(Original instructions)

damaged or defective.

u Never attempt to remove or replace

any parts other than those specied in

this manual.

Additional safety instructions

u The inator should not be used as a

vacuum cleaner (suck up dirt, debris,

or materials). It can be used as a

deator (removing air from inatable

products).

u Inate bike tyres, balls, rafts,

swimming pool oats, air mattresses,

and more in and around the home.

Recommended maximum continuous

duty at 65 psi is 2 minutes on with 5

minutes off.

u The compressed air from your inator

is not safe for breathing. Never

inhale air from your inator or from

a breathing device connected to the

inator.

u Too much air pressure causes a

hazardous risk of bursting.

Check the manufacturer’s maximum

pressure rating for objects being

inated.

u Do not leave inator running

unattended. It could burst tyres or

other items.

u Use a tire gauge to check the tyres

pressure before each use and while

inating tyres; see the tyre sidewall for

the correct tyre pressure.

u Do not modify or attempt to repair.

Never drill into, weld, or make any

modications to the inator or its

attachments.

u Operate only with the accessories in-

cluded or air handling parts acceptable

for not less than 160 psi.

u The use of any

accessory not recom-

mended for use with this tool could

be hazardous.

u Never “horseplay.” High pressure air

is dangerous. Don’t direct air-ow at

yourself or others.

Warning! Always leave the valve adaptor

lever open when not in use.

u Inator can become hot during use.

Allow inator to cool 30 minutes before

storing away.

After use

u Unplug the charger before cleaning.

u When not in use, the appliance should

be stored in a dry place.

u Children should not have access to

stored appliances.

Residual risks

Additional residual risks may arise when

using the tool which may not be included

in the enclosed safety warnings. These

risks can arise from misuse, prolonged

use etc.

Even with the application of the relevant

safety regulations and the implementa-

tion of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any

rotating/moving parts.

u Injuries caused when changing any

ENGLISH

(Original instructions)

parts, blades or accessories.

u Injuries caused by prolonged use

of a tool. When using any tool for

prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing

dust developed when using your

tool (example:- working with wood,

especially oak, beech and MDF.)

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u The battery terminals are not to be

short-circuited.

u Do not store in locations where the

temperature may exceed 40 °C.

u Charge only at ambient temperatures

between 10 °C and 40 °C.

u Charge only using the charger

provided with the tool.

u If the appliance is to be stored unused

for a long period, the batteries should

be removed.

u When disposing of batteries, follow

the instructions given in the section

“Protecting the environment”.

Do not attempt to charge dam-

aged batteries.

Chargers

u Use your STANLEY FATMAX charger

only to charge the battery in the tool

with which it was supplied. Other

batteries could burst, causing personal

injury and damage.

u Never attempt to charge non-

rechargeable batteries.

u Have defective cords replaced

immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Labels on tools

The following pictograms, along with the

date code, are shown on the tool:

Warning! To reduce the risk

of injury, the user must read

the instruction manual.

Do not expose the appliance

to rain or high humidity.

Before performing mainte-

nance or cleaning on the

appliance, unplug the supply

cord.

Do not leave the inator

unattended.

Class II appliance

Features

This tool includes some or all of the following features.

1. Main power switch

2. Mode power switch

3. Digital readout

4. Pressure setting buttons

5. Pressure mode/reset button

6. Handle

7. High-volume hose

8. Tapered nozzle (high volume hose)

9. Universal valve adapter

10 . High-pressure hose

11. High-volume pump deate connection

ENGLISH

(Original instructions)

12. High volume pump inator connection

13. 230V AC cord

14. 12V DC vehicle adapter

15. Inator needle valve

16. Brass coupler adapter

17. Standard tapered nozzle

Use

Warning! Let the tool work at its own pace.

Do not overload.

Charging the battery (Fig. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before.

The battery may become warm while charging; this is normal

and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the

charger will begin to charge automatically when the cell

temperature warms up or cools down.

Note: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before rst

use.

u Plug the charger (25) into an appropriate outlet before

inserting battery pack (21).

u The green charging light (25a) will blink continuously

indicating that the charging process has started.

u The completion of charge will be indicated by the green

charging light (25a) remaining ON continuously. The

battery pack (21) is fully charged and may be removed

and used at this time or left in the charger (25).

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Charger LED Modes

Charging:

Green LED Intermittent

Fully Charged:

Green LED Solid

Hot/Cold Pack Delay:

Green LED Intermittent

Red LED Solid

Note: The compatible charger(s) will not charge a faulty

battery pack. The charger will indicate a faulty battery pack by

refusing to light.

Note: This could also mean a problem with a charger. If the

charger indicates a problem, take the charger and battery

pack to be tested at an authorized service centre.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot or too cold,

it automatically starts a Hot/Cold Pack Delay, the green LED

(25a) will ash intermittently, while the red LED (25b) will

remain on continuously, suspending charging until the battery

has reached an appropriate temperature. The charger then

automatically switches to the pack charging mode. This

feature ensures maximum battery life.

Battery state of charge indicator (Fig. B)

The battery includes a state of charge indicator to quickly

determine the extent of battery life as shown in gure B. By

pressing the state of charge button (21a) you can easily view

the charge remaining in the battery as illustrated in gure B.

Installing and Removing the Battery Pack from the

tool

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack (Fig. C)

NOTE: For best results, make sure your battery pack is

fully charged.

To install the battery pack (21) into the inator, align the

battery pack with the rails inside inator’s battery port (22)

and slide it into the port until the battery pack is rmly

seated and ensure that it does not disengage.

To remove the battery pack from the tool, press the release

button (23) and rmly pull the battery pack out of the tool.

Insert it into the charger as described in the charger

section of this manual.

ENGLISH

(Original instructions)

Fitting the Accessories

Universal Valve Adapter (Fig. D)

Your inator is supplied with the inator needle valve (15),

a brass coupler (16) , and the standard tapered nozzle (17) ,

located on the side of the unit.

u To use the universal valve adapter (9), make sure the

lever is in the up position.

u Place the valve adapter over the stem of the inator

needle valve, brass coupler adapter or standard

tapered nozzle.

u Press the lever (18) on the universal valve adapter down

to lock it in place.

u Place the inator needle valve, brass coupler adapter or

tapered nozzle into the item to be inated.

Note: Always make sure that the lever is in the up position

when not in use. Operate your inator only with the

universal valve adapter or with the included nozzles.

Note: Make sure the universal valve adapter is rmly

locked in place before turning the inator on.

High-volume hose (Fig. E)

u Remove the high-volume hose (7) from the storage

location.

u Line up the notches (19) of the hose with the nubs (20)

of the high volume pump inator connection (12). Then,

slide the hose on and twist counter-clockwise

to secure.

u To remove, twist the hose clockwise and slide hose off.

Note: Many inatables have an internal ap that prevents

air loss during ination, especially air mattresses. Unless this

ap is displaced by the nozzle the inatable will not inate.

Push the nozzle rmly into the valve to make sure that you

push this ap out of the way.

Warning! Risk of Bursting. Excessive air pressure may cause

a hazardous risk of bursting or personal injury. Check the

manufacturer’s maximum pressure rating for items being

inated.

Note: If the pressure rating for the item being inated is above

100 p.s.i.g., note that the maximum run time is 10 minutes,

leave to rest for 20 minutes before reusing.

Switching on

Warning! Risk of Bursting. Do not leave unit running

unattended. Overination of tires and other items could result

in serious injury and property damage.

Note: When power is supplied to the inator by 12V, 18V

battery, or 230V AC the digital readout display will remain

on for approximately 10 minutes before the display shuts

off/goes into sleep mode. This occurs when the unit is not

operating. To wake up the system, the user will need to

push the pressure mode / reset button (5). At this time the

digital readout will turn on and the inator is ready for use.

Before switching your inator on, decide which power

source you will be using; 12V AC adapter, 230V AC plug or a

18V Max* battery pack.

u To use the 12V AC adapter, or 18V Max* battery pack

press the AC/DC power switch 1 located on the front of

the unit to DC.

u If using the 230V AC vehicle adapter (14), always fully

extend the 230V AC cord before each use.

u Connect the 12V AC vehicle adapter (14) into your

vehicles 12V AC accessory socket.

u To use the 230V AC cord, press the AC/DC switch (1)

located on the front of the unit to AC.

u If using the 230V AC cord (13), always fully extend

the cord before each use.

u Connect the 230V AC cord (13) into either a wall

outlet or an approapriate sized extension cord that

is plugged into a wall outlet.

To turn on high-volume

The high-volume hose is meant to be used for objects that

hold large amounts of air, such as air mattresses, rafts, and

swimming pool oats.

Note: The high-volume mode DOES NOT have an auto

shut-off feature.

u Attach the high-volume hose (7) to the high volume

pump inator connection (12) as described in the High

Volume Hose section.

u Insert the high-volume hose (7), or it’s tapered nozzle (8)

into the object being inated.

u Press the high-volume side of the mode power

switch (2), indicated by the air mattress symbol.

u To turn off, push the power switch to the center position.

To turn on high-pressure

The high-pressure hose is meant to be used for objects that

need more air pressure, such as tires and basketballs.

u Remove the high-pressure hose (10) from the storage.

u Attach a nozzle as described in the Universal valve

adapter section.

u Insert the nozzle into the object being inated.

u Press the high-pressure side of the mode power

switch (2), indicated by the tire symbol.

u To turn off, push the power switch to the center position.

Deate using the high-volume hose (Fig. G)

Warning! Beware of objects being ejected.

When deating, large amounts of air will exit the

high volume pump inator connection (12) . Ensure the

universal valve adapter is not pointed at anyone or anything.

u Remove the high-volume hose (7) from the storage

location.

ENGLISH

(Original instructions)

u Line up the hose end (24) with the high-volume pump

deate connection (11).

Then, rmly slide in the hose so it

is securly in place.

u Insert the hose, or it’s tapered nozzle (8) into the object

being deated.

u Press the high-volume side of the mode power

switch (2), indicated by the air mattress symbol.

u To turn off, push the power switch to the center position.

u To remove the hose, twist the hose counterclockwise

and slide hose off.

Setting the automatic shut-off pressure

Note: The digital readout will only show ination pressures

when the inator is being used. In both ination and pump

mode the unit will show battery status.

u To switch between the different units (psi, bar or kPa),

press the pressure mode/reset button (5) until the required

units are displayed.

u Press the - or + pressure setting buttons (4) until the

required pressure is displayed.

u After 3 seconds the display will ash and return to a

reading of “0.0”. This is normal.

u Connect the universal valve adapter (9) and accessories,

if required, to the item to be inated, making sure that

the lever of the universal valve adapter is in the down

position to lock it in place.

u To start the inator press the mode power switch (2),

towards the side of the tire symbol.

u When the item to be inated has reached the preset

value the unit will automatically turn off.

NOTE: You may notice the actual pressure reading may

drop after a couple of seconds. This is normal.

7. To stop the inator at any time, press the main power

button back to the center position.

Note: If the AC/DC power switch is turned off, all settings

will be lost and will need to be reentered. This is a safety

feature to prevent the risk of items OVER INFLATING.

Using the inator as a pressure gauge

u Connect the universal valve adapter (9) to the item to

be checked.

u Press the mode power switch (2), on the side of the tire

symbol.

u The digital readout will display the item’s pressure.

u After checking, press the mode power switch (2) back

to the center position and return the air hose to the

storage location.

Maintenance

Your STANLEY FATMAX corded and cordless appliance has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on cordless

appliances:

u Run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualied

persons in order to avoid a hazard .

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Products and batteries contain materials that can be recov-

ered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries according to

local provisions. Further information is available at

www.2helpU.com

Technical Data

SFMCE520

Voltage 18Vdc, 230Vac and 12V vehicle voltage

Weight 2.21Kg

Charger SFMCB11 SFMCB12 SFMCB14

Input Voltage

230 230 230

Output Voltage

18 18 18

Current A 1.25 2 4

Battery

SFMCB201 SFMCB202 SFMCB204 SFMCB206

Voltage V

18 18 18 18

Capacity Ah

1.5 2.0 4.0 6.0

Type

Li-Ion Li-Ion Li-Ion Li-Ion

N717290 REV01 08/2020

Australia & New Zealand

Stanley Black & Decker

www.stanleytools.com.au

Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)

810 Whitehorse Road Box Hill VIC 3128, Australia

Stanley SFMCE520 User manual

Brand: Stanley

Model: SFMCE520

Category: Car battery chargers

Type: User manual

Download PDF

report

Stanley SFMCE520 User manual

Stanley SFMCE520 User manual

Related papers

Other documents