Ashford Hobby Bench 2 Operating instructions

Type
Operating instructions

Ashford Hobby Bench 2 is a sturdy and versatile bench designed for comfortable weaving at your Ashford Rigid Heddle, Table, or Jack Loom. It features 7 height positions, allowing you to customize your weaving experience. The bench can also be tilted by lifting the back of the seat one hole higher than the front, providing additional ergonomic support. With its beautiful New Zealand silver beech timber finish, the Ashford Hobby Bench 2 is not only functional but also aesthetically pleasing.

Ashford Hobby Bench 2 is a sturdy and versatile bench designed for comfortable weaving at your Ashford Rigid Heddle, Table, or Jack Loom. It features 7 height positions, allowing you to customize your weaving experience. The bench can also be tilted by lifting the back of the seat one hole higher than the front, providing additional ergonomic support. With its beautiful New Zealand silver beech timber finish, the Ashford Hobby Bench 2 is not only functional but also aesthetically pleasing.

Ashford Guarantee
Thank you for purchasing this Ashford product. In the unlikely event there is
any fault in manufacture we will replace the item. To validate our guarantee
please visit our website or write to us.
Ashford Handicrafts Limited
415 West Street
PO Box 474, Ashburton 7700 New Zealand
Telephone 64 3 308 9087
Email: sales@ashford.co.nz Internet: www.ashford.co.nz
INSTRUCTIONS
Hobby Bench 2
HB31082018V5
With 7 height positions
Ashford Handicrafts Limited
415 West Street
PO Box 474, Ashburton 7700 New Zealand
Telephone 64 3 308 9087 Facsimile 64 3 308 8664
Email: sales@ashford.co.nz Internet: www.ashford.co.nz
x1
x4x8
x8
x12
Hobby Bench Assembly Instructions
Tools required: Screwdriver, Allen key (supplied), hammer.
Before commencing assembly, please read the instructions
completely, identify all the parts and hardware and note the
assembly sequence.
Finish: Your Hobby Bench is made from beautiful New
Zealand silver beech timber and has been lacquered for your
convenience. If desired Ashford Wax Finish may be applied to
further enhance its appearance.
1. Insert 2 dowels into each end of the 2 shelves. Use a hammer
to gently tap the dowels to the bottom of each hole.
2. Place one side flat on the floor so that the dowel holes are
facing upwards. Locate the 2 shelves, with the barrel nut holes
facing the feet, into the corresponding holes in the side.
3. Place the other side on top of the shelves with the dowels
located into the corresponding holes.
4. Turn the Hobby Bench upside down and secure the shelves to
the sides with 4 bolt and barrel nuts.
5. Place the Hobby Bench on its feet. Attach the 2 height
adjusters with the holes for the barrel nuts facing in, to the
sides using 2 bolts and knobs each. Choose your seat height
from the schedule at the end of these instructions.
6. Locate the 4 barrel nuts into the holes in the height adjusters.
7. Place the seat on top of the height adjusters and secure with 4
bolts.
8. Once you are comfortable with the seat height and angle, and
the Hobby Bench sits flat on the floor, firmly tighten all bolts
with the Allen key supplied.
Note. The Hobby Bench can be adjusted to your desired height
and can be tilted by lifting the back of the seat one hole higher
than the front. You may find it easier to adjust the seat height
while the bench is on its side.
The seat height has 7 positions with 12mm (1/2”) increments.
545, 557, 570, 582, 595, 607, 620 mm (21 ½” , 22”, 22 ½”,
23”, 23 ½”, 24”, 24 ½”)
Use your new Hobby Bench for comfortable weaving at your
Ashford Rigid Heddle, Table or Jack Loom.
Project - Weave your own fabric, then pad and upholster your
Hobby Bench to personalise it
Dowel
Barrel nut
Bolt
Shelves
Height adjuster
Seat
Side
Knob Allen key (supplied)
  • Page 1 1
  • Page 2 2

Ashford Hobby Bench 2 Operating instructions

Type
Operating instructions

Ashford Hobby Bench 2 is a sturdy and versatile bench designed for comfortable weaving at your Ashford Rigid Heddle, Table, or Jack Loom. It features 7 height positions, allowing you to customize your weaving experience. The bench can also be tilted by lifting the back of the seat one hole higher than the front, providing additional ergonomic support. With its beautiful New Zealand silver beech timber finish, the Ashford Hobby Bench 2 is not only functional but also aesthetically pleasing.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI