AOpen DXPS Easy Installation Manual

Type
Easy Installation Manual

This manual is also suitable for

AOpen DXPS Plus is a high-performance motherboard that supports dual Intel Xeon CPUs with FSB up to 533MHz, providing exceptional processing power for demanding applications. It features four 184-pin DIMM sockets, allowing for up to 4GB of PC200/266 Registered memory, ensuring smooth multitasking and handling of large datasets.

AOpen DXPS Plus is a high-performance motherboard that supports dual Intel Xeon CPUs with FSB up to 533MHz, providing exceptional processing power for demanding applications. It features four 184-pin DIMM sockets, allowing for up to 4GB of PC200/266 Registered memory, ensuring smooth multitasking and handling of large datasets.

EPS 12V 24-
p
in Power Connector
Intel
®
82551 10/100Mbps
Ethernet Controller
604-pin CPU Socket x2
FSB400/533MHz Intel
®
Xeon
TM
CPU
Supported (FSB533 for DXPS-U /
DXPS Plus -U)
CPU Fan Connector with H/W
Monitoring x2
Server Works GC-SL Chipsets
North Bridge:Server Works GC-SL
184-pin DIMMx4 supports ECC DDR200
/ 266 maximum up to 4GB
Front Panel Connector
32bit/33MHz PCI Slot x2
Flash ROM BIOS
FDD Connector
68
p
in SCSI connector A
(
DXPS Plus/-U
)
CPU 2
S
y
stem Fan Connector
(
4-
p
ins
)
RJ45 LAN
Jack
IDE Connector (IDE1)
S
y
stem Fan Connector
IPMI Board Connector
(Optional)
Adaptec AIC-7902W Ultra 320
SCSI Controller (DXPS Plus
/ DXPS Plus-U
)
A
TI Ra
g
eXL Controller
64bit/100MHz PCI Slot x3
IDE Connector (IDE2)
68
p
in SCSI connector B
DXPS Plus/-U
)
IPMB connector
Slim CD-ROM Connector (IDE2)
Slim FDD Connector
64bit/100MHz PCI Slot x1 with
ZCR Function Support
( DXPS Plus/DXPS Plus-U)
Intel
®
82545 GbE
Ethernet Controller
COM2 Connector
S
y
stem Fan Connector
USB Connector
S
y
stem Fan Connector
South Bridge: Server Works CSB5
CPU2
CPU1
SPP/EPP/ECP Parallel Port
COM 1 Port
VGA Port
PS/2 Keyboard
Connector
EPS 12V 8-pin Power Connector
PS/2 Mouse
Connecto
r
USB1.1
Port
RJ45
100/10M
Port
1 GbE
Ethernet
Port
1. Installing CPU
2. Installing CPU & Housing Fan
Everything you need to boot
this motherboard is included in
this Easy Installation Guide.
For more information, a
complete Online User's Manual
can be found in the Bonus
Pack CD. Thanks for the help
of saving our earth.
PART NO: 90.51N30.002 DOC. NO: DXPSP-EG-E0209A
¾ Screw Pack for I/O Port
¾ Easy Installation Guide x 1
¾ MB Layout and jumper setting sticker label x1
¾ COM2 Cable x 1
¾ Ultra320 SCSI Cable x 1 (DXPS Plus only)
¾ Bonus Pack CD x 1
¾ Norton Anti-Virus CD x 1
¾ I/O Port Bracket x 1
¾ Floppy/IDE Cable Package
¾ Plate plastic for retention module assembly x2
¾ User Manual x1
Plug in the CPU fan cable to the 3-pin CPU FAN connector and housing fan cable to the HFan
connectors.
1. Pull up the CPU socket lever and up to
90-degree angle.
2. Locate Pin 1 in the socket and look for a
(golden) cut edge on the CPU upper interface.
Match Pin 1 and cut edge. Then insert the
CPU into the socket.
3. Press down the CPU socket lever and finish
CPU installation.
Note: If you do not match the CPU
socket Pin 1 and CPU cut edge
well, it may damage the CPU.
CPU Pin 1 and cut edge
CPU socket lever
Note: Some CPU fans do not have sensor pin, so that
cannot support fan monitoring.
GND
+12V
SENSOR
CPU Fan 1
HFan 2
SENSOR
+12V
GND
HFan 1
SENSOR
+12V
GND
HFan 3
SENSOR
+12V
GND
GND
+12V
SENSOR
CPU Fan 2
2 1
This motherboard has four 184-pin DIMM sockets that allow you to install PC200/266
Registered memory up to 4.0GB.
5. Connecting 68pin Ultra320 SCSI Cable (DXPS Plus/-U)
3. Install DIMM Modules
DIMM 1
DIMM 2
DIMM 3
DIMM 4
4. Connecting ATX Power Connector
This motherboard comes with a 24-pin and 8-pin ATX power connector. Make sure you
plug in the right direction. We strongly recommend you to connect the 8-pin 12V ATX
connector before connecting the 24-pin ATX power connector
6. Connecting IDE and Floppy Cables
The DXPS Plus provides two 68-pin Ultra320 SCSI connectors for 16-bit or 16-bit differential SCSI
devices. The Adaptec AIC-7902W controller provides 320MB/sec maximum data throughput per
channel available.
Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDC and IDE
connector. Pin1 of cable is normally marked with red color. Addition to normal connectors,
we provide you a slim type IDE2 connector and a slim type FDD connector. Please be
informed that DO NOT connect Secondary IDE Slim connector and Secondary IDE
Connector at the same time. As well as DO NOT connect FDD connector and slim FDD
connector at the same time.
FDD
Connector
Primary IDE Channel
Secondary IDE Channel
Secondary IDE Slim
Connector
Slim FDD
Connector
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PWR_OK
+5Vsb
+12V
+12V
+3.3V
Ground
Ground
Ground
Ground
+12V
+12V
+12V
+12V
2 1
DCD#
SOUT
GND
RI#
RTS#
8. Connecting COM2 Connector
9. Connecting Front Panel Connector
Attaching such as power switch, reset switch, HDD LED connector, etc.… to
corresponding pins.
10. Connecting IPMB Connector
IPMB offers good support for communication with on-board devices that are accessed
on an occasional basis. IPMB's competitive advantage over other low-speed
short-distance communication schemes is that its cost and complexity don't scale up
with the number of devices on the bus. The IPMB connector comes with foolproof
design, please connect it with correct orientation.
This motherboard comes with a COM1 connector on the back panel. However, we
provide an extra COM2 connector for your convenience. Once you need to connect a
device via COM2, just connect a suitable cable on it.
7. ZCR (Zero Channel RAID) Function (DXPS Plus/-U)
A ZCR card is a PCI card that allows a RAID card to use the onboard SCSI chip, thus
lowering cost of RAID solution.
A "Zero-channel" RAID adapter is a PCI RAID
controller that doesn't have any SCSI channels on board. Instead, it is designed to
use the on-board SCSI channels of the motherboard to implement a cost-effective
Hardware RAID solution. Please be informed that only the first PCI slot supports
ZCR function. (DXPS Plus/DXPS Plus-U)
IPMB Connector
ATX
Power Switch
Power
LED
Chassis
Intrusion Senso
r
Reset Switch
HDD
LED
12
21 22
COM2
Connector
SIN
DTR#
DSR#
CTS#
NC
1 2
2
13. Support 10/100 Mbps and 1Gbps LAN onboard
14. Connecting IPMI connector (Optional)
11. PC99 Color Coded Back Panel
12. JP1 Check Password Jumper
This motherboard provides check password function. You can use JP1 to enable or
disable this function, which could prevent your system from unauthorized invasion. The
factory default setting is set to “Disable”(2-3), and you may enable this function by setting
the jumper to 1-2.
The onboard I/O devices are PS/2 Keyboard, PS/2 Mouse, COM1, VGA, Printer and
USB1.1. The view angle of drawing shown here is from the back panel of the housing.
The Intel 82545EM integrates Intel’s fourth-generation Gigabit MAC design with fully
integrated, physical-layer circuitry to provide a standard IEEE 802.3 Ethernet interface for
1000BASE-T and 100BASE-TX applications. The left green LED indicates the link mode,
it lights when linking to network and blinking when transferring data. The right green LED
indicates the transfer mode, and it lights when data is transferring in 1Gbps/100Mbps
mode.
Green/ACT
Green/Speed
Green/ACT
Green/Speed
100/10Mb Ethernet Port
1Gb Ethernet Port
Intelligent Platform Management Interface (IPMI) is a hardware level interface
specification, defines a message-based interface to platform monitoring and control
function. IPMI’s monitoring abilities enable user to monitor server physical health
characteristics such as temperature, voltage, fans, power supplies and chassis.
(Optional)
JP1 Check Password Jumper
PS/2 Keyboard: For standard keyboard, which is using a PS/2 plug.
PS/2 Mouse: For PC-Mouse, which is using a PS/2 plug.
USB Port: Available for connecting USB devices.
Parallel Port: To connect with SPP/ECP/EPP printer.
COM1: To connect with pointing devices, modem or others serial devices.
VGA Connector: To connect with PC monitor.
1GbE Ethernet Port: To connect RJ-45 Ethernet Cable.
RJ45 10/100 Port: To connect RJ-45 Ethernet Cable.
SPP/EPP/ECP Parallel Port
COM 1 Port
VGA Port
PS/2 Keyboard
Connector
PS/2 Mouse
Connecto
r
USB1.1
Port
RJ45
100/10M
Port
1 GbE
Ethernet
Port
Pin1
1
17. Comparison Table
After you finish the setting of jumpers and connect correct cables. Power on and
enter the BIOS Setup, press <Del> during POST (Power On Self Test). Choose
"Load Default Settin
g
" for recommended o
p
timal
p
erformance.
Del
16. Power-On and Load BIOS Setup
18.Model name and BIOS version
DXPS R1.00 Sep. 10. 2002 AOpen Inc.
Model name and BIOS version can be found on upper left corner of first boot screen
(POST screen). For example:
DXPS is the model name of the motherboard; R1.00 is BIOS version
15. Support the 2
nd
USB1.1 Channel
This motherboard provides two USB channels to link USB devices, such as mouse,
keyboard, modem, printer, etc. There are two connectors on the PC99 back panel. You
can use proper cable to connect other USB connectors to the back panel or front panel of
chassis.
USBPWR0
USB_FP_P0-
USB_FP_P0+
GND
KEY
USBPWR0
USB_FP_P1-
USB_FP_P1+
GND
NC
1 2
2
Compare/Model Key Chip (North Bridge) CPU Support (Dual CPU)
DXPS Server Works
GC-SL(FSB:400MHz)
Support Intel Xeon 1.8 GHz
above (FSB:400MHz)
DXPS Plus
(With SCSI)
Server Works
GC-SL(FSB:400MHz)
Support Intel Xeon 1.8 GHz
above (FSB:400MHz)
DXPS-U Server Works
GC-SL(FSB:533MHz)
Support Intel Xeon 1.8 GHz
above (FSB:400/533MHz)
DXPS Plus-U
(
With SCSI
)
Server Works
GC-SL(FSB:533MHz)
Support Intel Xeon 1.8 GHz
above (FSB:400/533MHz)
The comparison table below will show the differences between DXPS series
motherboards.
If you encounter any trouble to boot you system, follow the
procedures accordingly to resolve the problem.
Part Number and Serial Number
The Part Number and Serial number are printed on bar code label. You can find this
bar code label on the outside packing, on PCI slot or on component side of PCB. For
example:
P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.
Part No. Serial No.
Part No.
Serial No.
Then connect your monitor and keyboard.
The problem was probably caused
by power supply or motherboard
failure. Please contact your reselle
r
or local distributor for repairing.
Perhaps your monitor is defective.
No
Yes
No
Yes
It is very possible that your keyboard
is defective.
During system rebooting, press Del to enter BIOS Setup. Choose
“Load Setup Default".
The problem should be caused by the
IDE cables or HDD itself.
Re-install Windows 2000.
Yes
Yes
Turn off the power and unplug the AC power cable, then remove all
of the addon cards and cables, including VGA, IDE, FDD, COM1,
COM2 and Printer.
Turn on the power, and check if
the power supply and CPU fan
work properly.
Start
Check if there is display.
Press Ctrl, and Alt key at the
same time, hold them and then
press Del to see if the
s
y
stem reboots.
Turn off the system and
re-connect the IDE cable.
Check if the system can
reboot successfully.
End
No
No
Online Manual: Please check the manual carefully and make sure the
jumper settings and installation procedure are correct.
http://www.aopen.com/tech/download/manual/default.htm
1
1
Test Report: We recommend choosing board/card/device from the
compatibility test reports for assembling your PC.
http://www.aopen.com/tech/report/default.htm
2
2
FAQ: The latest FAQ (Frequently Asked Questions) may contain a
solution to your problem.
http://www.aopen.com/tech/faq/default.htm
5
5
Download Software: Check out this table to get the latest updated
BIOS/utility and drivers.
http://www.aopen.com/tech/download/default.htm
3
3
News Group: Our support engineer or professional users on the news
group probably had answered your problem.
http://www.aopen.com/tech/newsgrp/default.htm
4
4
Contact Distributors/Resellers: We sell our products through resellers
and integrators. They should know your system configuration very well and
should be able to solve your problem efficiently and provide important
reference for you if next time you want to buy something else from them.
6
6
Contact Us: Please prepare detail system configuration and error symptom
before contacting us. The part number, serial number and BIOS version
are also very helpful.
7
7
Dear Customer,
Thanks for choosing AOpen products. To provide the best and fastest service to
our customer is our first priority. However, we receive numerous emails and
phone-calls worldwide everyday, it is very hard for us to serve everyone on time.
We recommend you follow the procedures below and seek help before contact
us. With your help, we can then continue to provide the best quality service to
more customers.
Thanks very much for your understanding!
AOpen Technical Supporting Team
Web Site: english.aopen.com.tw
E-mail: Send us email by going through the contact form below.
English http://english.aopen.com.tw/tech/default.htm
Japanese http://www.aopen.co.jp/tech/default.htm
Chinese http://www.aopen.com.tw/tech/default.htm
German http://www.aopencom.de/tech/default.htm
Simplified Chinese http://www.aopen.com.cn/tech/default.htm
Pacific Rim
AOpen Inc.
Tel: 886-2-3789-5888
Fax: 886-2-3789-5899
Europe
AOpen Computer b.v.
Tel: 31-73-645-9516
Fax: 31-73-645-9604
Germany
AOpen Computer GmbH.
Tel: 49-1805-559191
Fax: 49-2102-157799
China
艾爾鵬國際貿易(上海)有限公司
Tel: 86-21-6225-8622
Fax: 86-21-6225-7926
Japan
AOpen Japan Inc.
Tel: 81-048-290-1800
Fax: 81-048-290-1820
America
AOpen America Inc.
Tel: 1-510-489-8928
Fax: 1-510-489-1998
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AOpen DXPS Easy Installation Manual

Type
Easy Installation Manual
This manual is also suitable for

AOpen DXPS Plus is a high-performance motherboard that supports dual Intel Xeon CPUs with FSB up to 533MHz, providing exceptional processing power for demanding applications. It features four 184-pin DIMM sockets, allowing for up to 4GB of PC200/266 Registered memory, ensuring smooth multitasking and handling of large datasets.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI