Thermal Dynamics 42 CUTMASTER Operating instructions

Brand: Thermal Dynamics

Model: 42 CUTMASTER

Category: Welding System

Type: Operating instructions

AMP

PHASE

Art # A-09347_AE

PLASMA CUTTING SYSTEM

CUTMASTER

™

Rev. AD Date: November 22, 2011 Manual # 0-5141

Operating Features:

Operating Manual

WE APPRECIATE YOUR BUSINESS!

Congratulations on your new Thermal Dynamics product. We

are proud to have you as our customer and will strive to provide

you with the best service and reliability in the industry. This

product is backed by our extensive warranty and world-wide

service network. To locate your nearest distributor or service

provider visit us on the web at www.cigweld.com.au (Asia

Pacific) www.thermal-dynamics.com (Americas and Europe).

This Operating Manual has been designed to instruct you on the

correct use and operation of your Thermal Dynamics product. Your

satisfaction with this product and its safe operation is our ultimate

concern. Therefore please take the time to read the entire manual,

especially the Safety Precautions. They will help you to avoid

potential hazards that may exist when working with this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

Thermal Dynamics is a Global Brand of manual and automation

Plasma Cutting Products for Thermadyne Industries Inc.

We distinguish ourselves from our competition through market-

leading, dependable products that have stood the test of time.

We pride ourselves on technical innovation, competitive prices,

excellent delivery, superior customer service and technical support,

together with excellence in sales and marketing expertise.

Above all, we are committed to developing technologically

advanced products to achieve a safer working environment within

the welding industry.

WARNINGS

Read and understand this entire Manual and your employer’s safety practices before installing, operat-

ing, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer's best judgement, the

Manufacturer assumes no liability for its use.

Plasma Cutting Power Supply

CutMaster™ 42

SL40 Torch™

Operating Manual Number 0-5141

Published by:

Thermal Dynamics Corporation

82 Benning Street

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

www.thermal-dynamics.com

Thermadyne Corporation

Reproduction of this work, in whole or in part, without written permission of the publisher is

prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or

damage caused by any error or omission in this Manual, whether such error results from negli-

gence, accident, or any other cause.

Printed in the United States of America

Publication Date: October 15, 2010

Revision AD Date: November 22, 2011

Record the following information for Warranty purposes:

Where Purchased:_______________________________ __________________

Purchase Date:__________________________________ __________________

Power Supply Serial #:___________________________ ___________________

Torch Serial #:___________________________________ _________________

TABLE OF CONTENTS

SECTION 1:

GENERAL INFORMATION ................................................................................................................ 1-1

1.01 Notes, Cautions and Warnings ................................................................................. 1-1

1.02 Important Safety Precautions ................................................................................... 1-1

1.03 Publications .............................................................................................................. 1-3

1.04 Note, Attention et Avertissement .............................................................................. 1-4

1.05 Precautions De Securite Importantes ....................................................................... 1-4

1.06 Documents De Reference ......................................................................................... 1-6

1.07 Declaration of Conformity......................................................................................... 1-7

1.08 Statement of Warranty ............................................................................................. 1-8

SECTION 2 SYSTEM:

INTRODUCTION .............................................................................................................................. 2-1

2.01 Working Principle ..................................................................................................... 2-1

2.02 Power Supply Speciﬁcations .................................................................................... 2-1

2.03 Input Wiring Speciﬁcations ...................................................................................... 2-2

2.04 Power Supply Features ............................................................................................. 2-3

2.05 Torch Speciﬁcations ................................................................................................. 2-4

SECTION 2TORCH:

INTRODUCTION ............................................................................................................................ 2T-1

2T.01 Scope of Manual..................................................................................................... 2T-1

2T.02 Speciﬁcations ........................................................................................................ 2T-1

2T.03 Introduction to Plasma ........................................................................................... 2T-2

SECTION 3:

INSTALLATION ................................................................................................................................ 3-1

3.01 Unpacking ................................................................................................................ 3-1

3.02 Lifting Options .......................................................................................................... 3-1

3.03 Primary Input Power Connections ............................................................................ 3-2

SECTION 4 SYSTEM:

OPERATION ..................................................................................................................................... 4-1

4.01 Control Panel ............................................................................................................ 4-1

4.02 Preparations For Operating....................................................................................... 4-2

4.03 Sequence of Operation ............................................................................................. 4-4

4.04 Cut Quality ................................................................................................................ 4-6

4.05 General Cutting Information ..................................................................................... 4-7

SECTION 5 SYSTEM: SERVICE ................................................................................................................. 5-1

5.01 General Maintenance ................................................................................................ 5-1

5.02 Basic Troubleshooting Guide .................................................................................... 5-2

SECTION 5 TORCH:

SERVICE ........................................................................................................................................ 5T-1

5T.01 General Maintenance .............................................................................................. 5T-1

5T.02 Inspection and Replacement of Consumable Torch Parts ....................................... 5T-1

TABLE OF CONTENTS

SECTION 6:

PARTS LISTS ................................................................................................................................... 6-1

6.01 Introduction .............................................................................................................. 6-1

6.02 Power Supply Replacement Parts ............................................................................ 6-2

APPENDIX 1:

CIRCUIT DIAGRAM ..........................................................................................................................A-1

CUTMASTER 42

Manual 0-5141 1-1 GENERAL INFORMATION

SECTION 1:

GENERAL INFORMATION

1.01 Notes, Cautions and Warnings

Throughout this manual, notes, cautions, and warnings are used to

highlight important information. These highlights are categorized as

follows:

NOTE

An operation, procedure, or background information

which requires additional emphasis or is helpful in ef-

ﬁcient operation of the system.

CAUTION

A procedure which, if not properly followed, may cause

damage to the equipment.

WARNING

A procedure which, if not properly followed, may cause

injury to the operator or others in the operating area.

1.02 Important Safety Precautions

WARNING

OPERATION AND MAINTENANCE OF PLASMA ARC

EQUIPMENT CAN BE DANGEROUS AND HAZARDOUS

TO YOUR HEALTH.

Plasma arc cutting produces intense electric and magnet-

ic emissions that may interfere with the proper function

of cardiac pacemakers, hearing aids, or other electronic

health equipment. Persons who work near plasma arc

cutting applications should consult their medical health

professional and the manufacturer of the health equip-

ment to determine whether a hazard exists.

To prevent possible injury, read, understand and follow

all warnings, safety precautions and instructions before

using the equipment. Call 1-603-298-5711 or your local

distributor if you have any questions.

GASES AND FUMES

Gases and fumes produced during the plasma cutting process can be

dangerous and hazardous to your health.

• Keepallfumesandgasesfromthebreathingarea.Keepyour

head out of the welding fume plume.

• Useanair-suppliedrespiratorifventilationisnotadequateto

remove all fumes and gases.

• Thekindsoffumesandgasesfromtheplasmaarcdependon

the kind of metal being used, coatings on the metal, and the

different processes. You must be very careful when cutting

or welding any metals which may contain one or more of the

following:

Antimony Chromium Mercury

Arsenic Cobalt Nickel

Barium Copper Selenium

Beryllium Lead Silver

Cadmium Manganese Vanadium

• AlwaysreadtheMaterialSafetyDataSheets(MSDS)thatshould

be supplied with the material you are using. These MSDSs

will give you the information regarding the kind and amount of

fumes and gases that may be dangerous to your health.

• Forinformationonhowtotestforfumesandgasesinyour

workplace, refer to item 1 in Subsection 1.03, Publications in

this manual.

• Usespecialequipment,suchaswaterordowndraftcutting

tables, to capture fumes and gases.

• Donotusetheplasmatorchinanareawherecombustibleor

explosive gases or materials are located.

• Phosgene,atoxicgas,isgeneratedfromthevaporsofchlo-

rinated solvents and cleansers. Remove all sources of these

vapors.

• Thisproduct, when used for welding or cutting, produces

fumes or gases which contain chemicals known to the State

of California to cause birth defects and, in some cases, cancer.

(California Health & Safety Code Sec. 25249.5 et seq.)

ELECTRIC SHOCK

Electric Shock can injure or kill. The plasma arc process uses and

produces high voltage electrical energy. This electric energy can cause

severe or fatal shock to the operator or others in the workplace.

• Nevertouchanypartsthatareelectrically“live”or“hot.”

• Weardryglovesandclothing.Insulateyourselffromthework

piece or other parts of the welding circuit.

• Repairorreplaceallwornordamagedparts.

• Extracaremustbetakenwhen the workplace is moist or

damp.

• InstallandmaintainequipmentaccordingtoNECcode,referto

item 9 in Subsection 1.03, Publications.

• Disconnect power source before performingany serviceor

repairs.

• ReadandfollowalltheinstructionsintheOperatingManual.

FIRE AND EXPLOSION

Fire and explosion can be caused by hot slag, sparks, or the plasma

arc.

• Besurethereisnocombustibleorammablematerialinthe

workplace. Any material that cannot be removed must be

protected.

• Ventilateallammable or explosive vapors from the work-

place.

• Donotcutorweldoncontainersthatmayhaveheldcombus-

tibles.

CUTMASTER 42

GENERAL INFORMATION 1-2 Manual 0-5141

• Providearewatchwhenworkinginanareawhererehazards

may exist.

• Hydrogengas may beformedand trapped underaluminum

workpieces when they are cut underwater or while using a water

table. DO NOT cut aluminum alloys underwater or on a water

table unless the hydrogen gas can be eliminated or dissipated.

Trapped hydrogen gas that is ignited will cause an explosion.

NOISE

Noise can cause permanent hearing loss. Plasma arc processes can

cause noise levels to exceed safe limits. You must protect your ears

from loud noise to prevent permanent loss of hearing.

• Toprotectyourhearingfromloudnoise,wearprotectiveear

plugs and/or ear muffs. Protect others in the workplace.

• Noiselevelsshouldbemeasuredtobesurethedecibels(sound)

do not exceed safe levels.

• Forinformationonhowtotestfornoise,seeitem1inSubsec-

tion 1.03, Publications, in this manual.

LEAD WARNING

This product contains chemicals, including lead, or otherwise

produces chemicals known to the State of California to cause

cancer, birth defects and other reproductive harm. Wash hands

after handling. (California Health & Safety Code § 25249.5 et seq.)

PLASMA ARC RAYS

Plasma Arc Rays can injure your eyes and burn your skin. The plasma

arc process produces very bright ultra violet and infrared light. These

arc rays will damage your eyes and burn your skin if you are not

properly protected.

• Toprotectyoureyes,alwayswearaweldinghelmetorshield.

Also always wear safety glasses with side shields, goggles or

other protective eye wear.

• Wearweldingglovesandsuitableclothingtoprotectyourskin

from the arc rays and sparks.

• Keephelmetand safetyglassesin goodcondition. Replace

lenses when cracked, chipped or dirty.

• Protectothersintheworkareafromthearcrays.Useprotective

booths, screens or shields.

• Usetheshadeoflensassuggestedinthefollowingchart.

NOTE

These values apply where the actual arc is clearly

seen. Experience has shown that lighter ﬁlters may

be used when the arc is hidden by the workpiece.

AWS F2.2:2001 (R2010), Adapted with permission of the American Welding Society (AWS), Miami, Florida

Guide for Shade Numbers

(from AWS F2.2, Lens Shade Selector)

Shade numbers are given as a guide only and may be varied to suit individual needs.

Process Electrode Size in. (mm)

Arc Current

(Amperes)

Minimum

Protective

Shade

Suggested*

Shade No.

(Comfort)

Shielded Metal Arc Welding (SMAW)

Less than 3/32 (2.4)

3/32-5/32 (2.4-4.0)

5/32-1/4 (4.0-6.4)

More than 1/4 (6.4)

Less than 60

60-160

160-250

250-550

Gas Metal Arc Weding (GMAW) and

Flux Cored Arc Welding (FCAW)

Less than 60

60-160

160-250

250-550

Gas Tungsten arc Welding (GTAW)

Less than 50

50-150

150-500

Air Carbon Arc Cutting (CAC-A)

(Light)

(Heavy)

Less than 500

500-1000

Plasma Arc Welding (PAW)

Less than 20

20-100

100-400

400-800

6 to 8

Plasma Arc Cutting (PAC)

Less than 20

20-40

40-60

60-80

80-300

300-400

400-800

* As a rule of thumb, start with a shade that is too dark to see the weld zone. Then go to a lighter shade

which gives sufﬁcient view of the weld zone without going below the minimum. In oxyfuel gas welding,

cutting,orbrazingwherethetorchand/ortheuxproducesahighyellowlight,itisdesirabletousea

ﬁlter lens that absorbs the yellow or soduim line of the visible light spectrum.

Table 1-1

CUTMASTER 42

Manual 0-5141 1-3 GENERAL INFORMATION

1.03 Publications

Refer to the following standards or their latest revisions for more

information:

1. OSHA, SAFETY AND HEALTH STANDARDS, 29CFR 1910, obtain-

able from the Superintendent of Documents, U.S. Government

Printing Ofﬁce, Washington, D.C. 20402

2. ANSI Standard Z49.1, SAFETY IN WELDING AND CUTTING, ob-

tainable from the American Welding Society, 550 N.W. LeJeune

Rd, Miami, FL 33126

3. NIOSH, SAFETY AND HEALTH IN ARC WELDING AND GAS

WELDING AND CUTTING, obtainable from the Superintendent of

Documents, U.S. Government Printing Ofﬁce, Washington, D.C.

20402

4. ANSI Standard Z87.1, SAFE PRACTICES FOR OCCUPATION AND

EDUCATIONAL EYE AND FACE PROTECTION, obtainable from

American National Standards Institute, 1430 Broadway, New York,

NY 10018

5. ANSI Standard Z41.1, STANDARD FOR MEN’S SAFETY-TOE

FOOTWEAR, obtainable from the American National Standards

Institute, 1430 Broadway, New York, NY 10018

6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USE OF CUTTING

AND WELDING PROCESSES, obtainable from American National

Standards Institute, 1430 Broadway, New York, NY 10018

7. AWS Standard A6.0, WELDING AND CUTTING CONTAINERS

WHICH HAVE HELD COMBUSTIBLES, obtainable from American

Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

8. NFPA Standard 51, OXYGEN-FUEL GAS SYSTEMS FOR WELD-

ING, CUTTING AND ALLIED PROCESSES, obtainable from the

National Fire Protection Association, Batterymarch Park, Quincy,

MA 02269

9. NFPA Standard 70, NATIONAL ELECTRICAL CODE, obtainable

from the National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269

10. NFPA Standard 51B, CUTTING AND WELDING PROCESSES,

obtainable from the National Fire Protection Association, Bat-

terymarch Park, Quincy, MA 02269

11. CGA Pamphlet P-1, SAFE HANDLING OF COMPRESSED GASES

IN CYLINDERS, obtainable from the Compressed Gas Association,

1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202

12. CSA Standard W117.2, CODE FOR SAFETY IN WELDING AND

CUTTING, obtainable from the Canadian Standards Association,

Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada

M9W 1R3

13. NWSA booklet, WELDING SAFETY BIBLIOGRAPHY obtainable

from the National Welding Supply Association, 1900 Arch Street,

Philadelphia, PA 19103

14. American Welding Society Standard AWSF4.1, RECOMMENDED

SAFE PRACTICES FOR THE PREPARATION FOR WELDING AND

CUTTING OF CONTAINERS AND PIPING THAT HAVE HELD HAZ-

ARDOUS SUBSTANCES, obtainable from the American Welding

Society, 550 N.W. LeJeune Rd, Miami, FL 33126

15. ANSI Standard Z88.2, PRACTICE FOR RESPIRATORY PROTEC-

TION, obtainable from American National Standards Institute, 1430

Broadway, New York, NY 10018

CUTMASTER 42

GENERAL INFORMATION 1-4 Manual 0-5141

1.04 Note, Attention et Avertissement

Danscemanuel,lesmots“note,”“attention,”et“avertissement”

sont utilisés pour mettre en relief des informations à caractère

important. Ces mises en relief sont classiﬁées comme suit :

NOTE

Toute opération, procédure ou renseignement général sur

lequel il importe d’insister davantage ou qui contribue à

l’efﬁcacité de fonctionnement du système.

ATTENTION

Toute procédure pouvant résulter l’endommagement

du matériel en cas de non-respect de la procédure en

question.

AVERTISSEMENT

Toute procédure pouvant provoquer des blessures de

l’opérateur ou des autres personnes se trouvant dans

la zone de travail en cas de non-respect de la procédure

en question.

1.05 Precautions De Securite

Importantes

AVERTISSEMENTS

L’OPÉRATION ET LA MAINTENANCE DU MATÉRIEL

DE SOUDAGE À L’ARC AU JET DE PLASMA PEUVENT

PRÉSENTER DES RISQUES ET DES DANGERS DE

SANTÉ.

Coupant à l’arc au jet de plasma produit de l’énergie

électrique haute tension et des émissions magnétique qui

peuventinterférerlafonctionpropred’un“pacemaker”

cardiaque, les appareils auditif, ou autre matériel de santé

electronique. Ceux qui travail près d’une application à

l’arc au jet de plasma devrait consulter leur membre pro-

fessionel de médication et le manufacturier de matériel de

santé pour déterminer s’il existe des risques de santé.

Il faut communiquer aux opérateurs et au personnel

TOUS les dangers possibles. Aﬁn d’éviter les blessures

possibles, lisez, comprenez et suivez tous les avertisse-

ments, toutes les précautions de sécurité et toutes les

consignes avant d’utiliser le matériel. Composez le +

603-298-5711 ou votre distributeur local si vous avez

des questions.

FUMÉE et GAZ

La fumée et les gaz produits par le procédé de jet de plasma peuvent

présenter des risques et des dangers de santé.

• Eloigneztoutefuméeetgazdevotrezonederespiration.Gardez

votre tête hors de la plume de fumée provenant du chalumeau.

• Utilisezunappareilrespiratoireàalimentationenairsil’aération

fournie ne permet pas d’éliminer la fumée et les gaz.

• Les sortes de gaz et de fumée provenant de l’arc de plasma

dépendent du genre de métal utilisé, des revêtements se trouvant

sur le métal et des différents procédés. Vous devez prendre soin

lorsque vous coupez ou soudez tout métal pouvant contenir un

ou plusieurs des éléments suivants:

antimoine cadmium mercure

argent chrome nickel

arsenic cobalt plomb

baryum cuivre sélénium

béryllium manganèse vanadium

• Liseztoujoursleschesdedonnéessurlasécuritédesmatières

(sigleaméricain“MSDS”);celles-cidevraientêtrefourniesavec

le matériel que vous utilisez. Les MSDS contiennent des rensei-

gnements quant à la quantité et la nature de la fumée et des gaz

pouvant poser des dangers de santé.

• Pourdesinformationssurlamanièredetesterlafuméeetlesgaz

de votre lieu de travail, consultez l’article 1 et les documents cités

à la page 5.

• Utilisezunéquipementspécialtelquedestablesdecoupeàdébit

d’eau ou à courant descendant pour capter la fumée et les gaz.

• N’utilisezpaslechalumeauaujetdeplasmadansunezoneoùse

trouvent des matières ou des gaz combustibles ou explosifs.

• Lephosgène,ungaztoxique,estgénéréparlafuméeprovenant

des solvants et des produits de nettoyage chlorés. Eliminez toute

source de telle fumée.

• Ceproduit,dansleprocéderdesoudageetdecoupe,produitde

la fumée ou des gaz pouvant contenir des éléments reconnu dans

L’état de la Californie, qui peuvent causer des défauts de naissance

et le cancer. (La sécurité de santé en Californie et la code sécurité

Sec. 25249.5 et seq.)

CHOC ELECTRIQUE

Les chocs électriques peuvent blesser ou même tuer. Le procédé

au jet de plasma requiert et produit de l’énergie électrique haute

tension. Cette énergie électrique peut produire des chocs graves,

voire mortels, pour l’opérateur et les autres personnes sur le lieu de

travail.

• Netouchezjamaisunepièce“soustension”ou“vive”;portezdes

gants et des vêtements secs. Isolez-vous de la pièce de travail ou

des autres parties du circuit de soudage.

• Réparezouremplaceztoutepièceuséeouendommagée.

• Prenezdessoinsparticulierslorsquelazonedetravailesthumide

ou moite.

• MontezetmaintenezlematérielconformémentauCodeélectrique

national des Etats-Unis. (Voir la page

article 9.)

• Débranchezl’alimentationélectriqueavanttouttravaild’entretien

ou de réparation.

• Lisez et respecteztoutes les consignesdu Manuel de

consignes.

CUTMASTER 42

Manual 0-5141 1-5 GENERAL INFORMATION

INCENDIE ET EXPLOSION

Les incendies et les explosions peuvent résulter des scories chaudes,

des étincelles ou de l’arc de plasma. Le procédé à l’arc de plasma

produit du métal, des étincelles, des scories chaudes pouvant

mettre le feu aux matières combustibles ou provoquer l’explosion de

fumées inflammables.

• Soyezcertainqu’aucunematièrecombustibleou inflammable

ne se trouve sur le lieu de travail. Protégez toute telle matière

qu’il est impossible de retirer de la zone de travail.

• Procurezunebonneaérationdetouteslesfuméesinflammables

ou explosives.

• Necoupezpasetnesoudezpaslesconteneursayantpu

renfermer des matières combustibles.

• Prévoyezuneveilled’incendielorsdetouttravaildansunezone

présentant des dangers d’incendie.

• Legashydrogènepeutseformerous’accumulersousles

pièces de travail en aluminium lorsqu’elles sont coupées sous

l’eau ou sur une table d’eau. NE PAS couper les alliages en

aluminium sous l’eau ou sur une table d’eau à moins que le gas

hydrogène peut s’échapper ou se dissiper. Le gas hydrogène

accumulé explosera si enflamm

é.

RAYONS D’ARC DE PLASMA

Les rayons provenant de l’arc de plasma peuvent blesser vos yeux et

brûler votre peau. Le procédé à l’arc de plasma produit une lumière

infra-rouge et des rayons ultra-violets très forts. Ces rayons d’arc

nuiront à vos yeux et brûleront votre peau si vous ne vous protégez

pas correctement.

• Pour protéger vos yeux, portez toujours un casque ou un

écran de soudeur. Portez toujours des lunettes de sécurité

munies de parois latérales ou des lunettes de protection ou

une autre sorte de protection oculaire.

• Portezdesgantsdesoudeuretunvêtementprotecteur

approprié pour protéger votre peau contre les étincelles et

les rayons de l’arc.

• Maintenezvotrecasqueetvoslunettesdeprotectionenbon

état. Remplacez toute lentille sale ou comportant fissure ou

rognure.

• Protégezles autres personnessetrouvantsur la zonede

travail contre les rayons de l’arc en fournissant des cabines

ou des écrans de protection.

• Utilisezlanuancedelentillequiestsuggèréedansle

recommendation qui suivent ANSI/ASC Z49.1:

Nuance Minimum Nuance Suggerée

Courant Arc Protective Numéro Numéro

Moins de 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* Ces valeurs s’appliquent ou l’arc actuel est observé

clairement. L’experience a démontrer que les filtres

moins foncés peuvent être utilisés quand l’arc est

caché par moiceau de travail.

BRUIT

Le bruit peut provoquer une perte permanente de l’ouïe. Les procédés

de soudage à l’arc de plasma peuvent provoquer des niveaux sonores

supérieurs aux limites normalement acceptables. Vous dú4ez vous

protéger les oreilles contre les bruits forts aﬁn d’éviter une perte

permanente de l’ouïe.

• Pourprotégervotreouïecontrelesbruitsforts,portezdes

tampons protecteurs et/ou des protections auriculaires. Pro-

tégez également les autres personnes se trouvant sur le lieu

de travail.

• Ilfaut mesurer les niveaux sonores an d’assurer queles

décibels (le bruit) ne dépassent pas les niveaux sûrs.

• Pourdesrenseignementssurlamanièredetesterlebruit,

consultez l’article 1, page 5.

PLOMB AVERTISSEMENT

Ce produit contient des produits chimiques, comme le plomb,

ou engendre des produits chimiques, reconnus par l’état

de Californie comme pouvant être à l’origine de cancer, de

malformations fœtales ou d’autres problèmes de reproduction.

Il faut se laver les mains après toute manipulation.

(Code de Californie de la sécurité et santé, paragraphe 25249.5 et

suivants)

CUTMASTER 42

GENERAL INFORMATION 1-6 Manual 0-5141

1.06 Documents De Reference

Consultez les normes suivantes ou les révisions les plus récentes

ayant été faites à celles-ci pour de plus amples renseignements :

1. OSHA, NORMES DE SÉCURITÉ DU TRAVAIL ET DE

PROTECTION DE LA SANTÉ, 29CFR 1910, disponible auprès du

Superintendent of Documents, U.S. Government Printing Office,

Washington, D.C. 20402

2. Norme ANSI Z49.1, LA SÉCURITÉ DES OPÉRATIONS DE COUPE

ET DE SOUDAGE, disponible auprès de la Société Américaine de

Soudage (American Welding Society), 550 N.W. LeJeune Rd.,

Miami, FL 33126

3. NIOSH, LA SÉCURITÉ ET LA SANTÉ LORS DES OPÉRATIONS

DE COUPE ET DE SOUDAGE À L’ARC ET AU GAZ, disponible

auprès du Superintendent of Documents, U.S. Government

Printing Office, Washington, D.C. 20402

4. Norme ANSI Z87.1, PRATIQUES SURES POUR LA PROTECTION

DES YEUX ET DU VISAGE AU TRAVAIL ET DANS LES ECOLES,

disponible de l’Institut Américain des Normes Nationales

(American National Standards Institute), 1430 Broadway, New

York, NY 10018

5. Norme ANSI Z41.1, NORMES POUR LES CHAUSSURES

PROTECTRICES, disponible auprès de l’American National

Standards Institute, 1430 Broadway, New York, NY 10018

6. Norme ANSI Z49.2, PRÉVENTION DES INCENDIES LORS DE L’

EMPLOI DE PROCÉDÉS DE COUPE ET DE SOUDAGE, disponible

auprès de l’American National Standards Institute, 1430

Broadway, New York, NY 10018

7. Norme A6.0 de l’Association Américaine du Soudage (AWS), LE

SOUDAGE ET LA COUPE DE CONTENEURS AYANT RENFERMÉ

DES PRODUITS COMBUSTIBLES, disponible auprès de la

American Welding Society, 550 N.W. LeJeune Rd., Miami, FL

33126

8. Norme 51 de l’Association Américaine pour la Protection

contre les Incendies (NFPA), LES SYSTEMES À GAZ AVEC

ALIMENTATION EN OXYGENE POUR LE SOUDAGE, LA COUPE

ET LES PROCÉDÉS ASSOCIÉS, disponible auprès de la National

Fire Protection Association, Batterymarch Park, Quincy, MA

02269

9. Norme 70 de la NFPA, CODE ELECTRIQUE NATIONAL,

disponible auprès de la National Fire Protection Association,

Batterymarch Park, Quincy, MA 02269

10. Norme 51B de la NFPA, LES PROCÉDÉS DE COUPE ET DE

SOUDAGE, disponible auprès de la National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269

11. Brochure GCA P-1, LA MANIPULATION SANS RISQUE DES

GAZ COMPRIMÉS EN CYLINDRES, disponible auprès de l’

Association des Gaz Comprimés (Compressed Gas Association),

1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202

12. Norme CSA W117.2, CODE DE SÉCURITÉ POUR LE SOUDAGE

ET LA COUPE, disponible auprès de l’Association des Normes

Canadiennes, Standards Sales, 178 Rexdale Boulevard, Rexdale,

Ontario, Canada, M9W 1R3

13. Livret NWSA, BIBLIOGRAPHIE SUR LA SÉCURITÉ DU SOUDAGE,

disponible auprès de l’Association Nationale de Fournitures de

Soudage (National Welding Supply Association), 1900 Arch

Street, Philadelphia, PA 19103

14. Norme AWSF4.1 de l’Association Américaine de Soudage,

RECOMMANDATIONS DE PRATIQUES SURES POUR LA

PRÉPARATION À LA COUPE ET AU SOUDAGE DE CONTENEURS

ET TUYAUX AYANT RENFERMÉ DES PRODUITS DANGEREUX

, disponible auprès de la American Welding Society, 550 N.W.

LeJeune Rd., Miami, FL 33126

15. Norme ANSI Z88.2, PRATIQUES DE PROTECTION

RESPIRATOIRE, disponible auprès de l’American National

Standards Institute, 1430 Broadway, New York, NY 10018

CUTMASTER 42

Manual 0-5141 1-7 GENERAL INFORMATION

1.07 Declaration of Conformity

Manufacturer: Thermadyne Company

Address: 82 Benning Street

West Lebanon, New Hampshire 03784

USA

The equipment described in this manual conforms to all applicable aspects and regulations of the ‘Low Voltage Directive’ (European Council Directive

73/23/EEC as amended by Council Directive 93/68/EEC) and to the National legislation for the enforcement of this Directive.

The power supply equipment described in this manual conforms to CSA E60974-1 and the plasma torch equipment described in this manual

conforms to CSA E60974-7.

The equipment described in this manual conforms to all applicable aspects and regulations of the "EMC Directive" (European Council Directive

89/336/EEC) and to the National legislation for the enforcement of this Directive.

Serial numbers are unique with each individual piece of equipment and details description, parts used to manufacture a unit and date of manufacture.

National Standard and Technical Specifications

The product is designed and manufactured to a number of standards and technical requirements. Among them are:

* CSA (Canadian Standards Association) standard C22.2 number 60 for Arc welding equipment.

* UL (Underwriters Laboratory) rating 94VO flammability testing for all printed-circuit boards used.

* CENELEC EN50199 EMC Product Standard for Arc Welding Equipment.

* ISO/IEC 60974-1 (BS 638-PT10) (EN 60 974-1) (EN50192) (EN50078) applicable to plasma cutting equipment and associated accessories.

* AS60974.1 Arc Welding Equipment Welding Power Sources.

For environments with increased hazard of electrical shock, Power Supplies bearing the

mark conform to EN50192 when used in

conjunction with hand torches with exposed cutting tips, if equipped with properly installed standoff guides.

* Extensive product design verification is conducted at the manufacturing facility as part of the routine design and manufacturing process.

This is to ensure the product is safe, when used according to instructions in this manual and related industry standards, and performs as

specified. Rigorous testing is incorporated into the manufacturing process to ensure the manufactured product meets or exceeds all design

specifications.

Thermadyne has been manufacturing products for more than 30 years, and will continue to achieve excellence in our area of manufacture.

Manufacturers responsible representative in Europe: Steve Ward

Operations Director

Thermadyne Europe

Europa Building

Chorley N Industrial Park

Chorley, Lancashire,

England PR6 7BX

3163339

Certified to CSA

STD. E60974-1-00

CUTMASTER 42

GENERAL INFORMATION 1-8 Manual 0-5141

1.08 Statement of Warranty

LIMITED WARRANTY: Subject to the terms and conditions established below, Thermadyne Company warrants to the original retail purchaser that new

Thermal Dynamics CUTMASTER

plasma cutting systems sold after the effective date of this warranty are free of defects in material and workmanship.

Should any failure to conform to this warranty appear within the applicable period stated below, Thermadyne Company shall, upon notiﬁcation thereof and

substantiation that the product has been stored operated and maintained in accordance with Thermadyne’s speciﬁcations, instructions, recommendations

and recognized industry practice, correct such defects by suitable repair or replacement.

This warranty is exclusive and in lieu of any warranty of merchantability or ﬁtness for a particular purpose.

Thermadyne will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the

time periods set out below. Thermadyne Company must be notified within 30 days of any failure, at which time Thermadyne Company will provide

instructions on the warranty procedures to be implemented.

Thermadyne Company will honor warranty claims submitted within the warranty periods listed below. All warranty periods begin on the date of sale

of the product to the original retail customer or 1 year after sale to an authorized Thermadyne Distributor.

LIMITED WARRANTY PERIOD

Product

Power Supply Components

(Parts and Labor)

Torch and Leads

(Parts and Labor)

CUTMASTER 42 4 Year 1 Year

This warranty does not apply to:

1. Consumable Parts, such as tips, electrodes, shield cups, o - rings, starter cartridges, gas distributors, fuses, filters.

2. Equipment that has been modified by an unauthorized party, improperly installed, improperly operated or misused based upon industry standards.

In the event of a claim under this warranty, the remedies shall be, at the discretion of Thermadyne Company:

1. Repair of the defective product.

2. Replacement of the defective product.

3. Reimbursement of reasonable costs of repair when authorized in advance by Thermadyne.

4. Payment of credit up to the purchase price less reasonable depreciation based on actual use.

These remedies may be authorized by Thermadyne and are FOB West Lebanon, NH or an authorized Thermadyne service station. Product returned

for service is at the owner’s expense and no reimbursement of travel or transportation is authorized.

LIMITATION OF LIABILITY: Thermadyne Company shall not under any circumstances be liable for special or consequential damages such as, but not

limitedto,damageorlossofpurchasedorreplacementgoodsorclaimsofcustomerofdistributors(hereinafter“Purchaser”)forserviceinterruption.

The remedies of the Purchaser set forth herein are exclusive and the liability of Thermadyne with respect to any contract, or anything done in

connection therewith such as the performance or breach thereof, or from the manufacture, sale, delivery, resale, or use of the goods covered by or

furnished by Thermadyne whether arising out of contract, negligence, strict tort, or under any warranty, or otherwise, shall not, except as expressly

provided herein, exceed the price of the goods upon which liability is based.

This warranty becomes invalid if replacement parts or accessories are used which may impair the safety or performance of any Thermadyne

product.

This warranty is invalid if the Thermal Dynamics product is sold by non - authorized persons.

Effective October 15, 2010

CUTMASTER 42

Manual 0-5141 2-1 INTRODUCTION

SECTION 2 SYSTEM:

INTRODUCTION

2.01 Working Principle

Rectiﬁer

Inverter

Transformer

Rectiﬁer

Reduce pressure, ﬁlter

Gas valve Cutting torch

Workpiece

Compressed air

Art # A-09204_AB

2.02 Power Supply Speciﬁcations

CUTMASTER 42 Power Supply Speciﬁcations

Input Power 120 VAC (+

10%), 1Phase, 50/60Hz

208-230 VAC (+

10%), 1Phase, 50/60Hz

Output Current 20 Amps @ 120VAC, 15A

20-27 Amps @ 120VAC, 20A

20-40 Amps @ 230VAC, 20A

CUTMASTER 42 Power Supply Duty Cycle (Note 1)

Ambient Temperature 104° F (40° C)

Duty Cycle 30% @ 120VAC, 40% @ 230VAC

Rated Current 27 Amps @ 120VAC, 40 Amps @ 230V

SL40 Torch Gas Requirements (see section 2T.03)

Notes

1. Duty Cycle is the percentage of time the system can be operated without overheating. Duty cycle is re-

duced if primary input voltage (AC) is low or the DC voltage is higher than shown in this chart.

2. Air supply must be free of oil, moisture, and other contaminants. Excessive oil and moisture may cause

double-arcing, rapid tip wear, or even complete torch failure. Contaminants may cause poor cutting perfor-

mance and rapid electrode wear. Optional ﬁlters provide increased ﬁltering capabilities.

NOTE

IEC Rating is determined as speciﬁed by the International Electro-Technical Commission. These speciﬁca-

tions include calculating an output voltage based upon power supply rated current. To facilitate comparison

between power supplies, all manufacturers use this output voltage to determine duty cycle.

TDC Rating is determined using an output voltage representative of actual output voltage during cutting

with a TDC torch. This voltage may be more or less than IEC voltage, depending upon choice of torch,

consumables, and actual cutting operation.

CUTMASTER 42

INTRODUCTION 2-2 Manual 0-5141

Art# A-09333_AC

26lb / 11.8kg

7" (177mm)

18.5" (469.9mm)

9" (228.6mm)

CUTMASTER

120V 15A

120V 20A

230V 20A

Figure 2-1 Power Supply Dimensions & Weight

NOTE

Weight includes torch & leads, input power cord, and work cable with clamp.

CAUTION

Provideclearanceforproperairowthroughthepowersupply.Operationwithoutproperairowwill

inhibit proper cooling and reduce duty cycle.

2.03 Input Wiring Speciﬁcations

CUTMASTER 42 Input Power Requirements

Input Power Input Current Input Current Input Suggested Sizes (See Note)

Voltage Freq. (kVA) Max (Amps) Ieff (Amps) Fuse (Amps)

(Volts-AC) (Hz) 1-Ph 1-Ph 1-Ph 1-Ph

120 50/60 3.3 27.5 15 25

208 50/60 5.0 24 15.4 23

230 50/60 5.0 21.4 13.5 20

240 50/60 5.0 20.8 13 20

Line Voltages with Suggested Circuit Protection

Motor start fuses or thermal circuit breakers are recommended for this application. Check local requirements for your situation

in this regard.

NOTE

Refer to Local and National Codes or local authority having jurisdiction for proper wiring requirements.

Cable size is de-rated based on the Duty Cycle of the equipment.

Thesuggestedsizesarebasedonexiblepowercablewithpowerpluginstallations.

Cable conductor temperature used is 167° F (75° C).

CUTMASTER 42

Manual 0-5141 2-3 INTRODUCTION

2.04 Power Supply Features

Air Inlet

Control Panel

Torch Lead

120/230 VAC Power Source

Work Cable and Clamp

Art # A-09334_AC

CUTMASTER

120V 15A

120V 20A

230V 20A

Art# A-09335

Air Inlet

On/Off

Switch

Power Cord

2.05 Torch Speciﬁcations

A. Torch Conﬁguration and Dimensions

The torch head is at 75° to the torch handle. The torch includes a torch handle and torch trigger assembly.

10.125" (257 mm)

3.75"

(95 mm)

1.17" (29 mm)

Art # A-03322_AB

Torch Conﬁguration and Dimensions

B. Torch Leads Lengths

Leads are available in 10 ft (3 m) lengths.

C. Parts-In-Place (PIP)

Torch has built-in switch.

12 vdc circuit rating

D. Type of Cooling

Combination of ambient air and gas stream through torch.

E. SL60 Torch Ratings

(Refer to Note)

NOTE

Ratings shown apply to the SL60 Torch only. Refer to the Speciﬁcations chart on page 2T-1 for CutSkill

35A data.

F. Plasma Power Supply Used With

• Thermal Dynamics CutSkill 35A

CUTMASTER 42

Manual 0-5141 2T-1 INTRODUCTION

SECTION 2TORCH:

INTRODUCTION

2T.01 Scope of Manual

This manual contains descriptions, operating instruc-

tions and maintenance procedures for the SL40 Plasma

Cutting Torch. Service of this equipment is restricted

toproperlytrainedpersonnel;unqualiedpersonnelare

strictly cautioned against attempting repairs or adjust-

ments not covered in this manual, at the risk of voiding

the Warranty. Read this manual thoroughly. A complete

understanding of the characteristics and capabilities of

this equipment will assure the dependable operation for

which it was designed.

2T.02 Speciﬁcations

A. Torch Conﬁgurations

1. Hand Torch, Model SL40

The hand torch head is at 75° to the torch handle.

The hand torches include a torch handle and torch

trigger assembly.

8.3" (210.82mm)

2.6"

(66.04mm)

Radnor Version

.96" (24.38mm)

Art # A-09336

B. Torch Leads Lengths

Hand Torches are available as follows:

• 15ft/4.6m.

C. Torch Parts

Starter Cartridge, Electrode, Tip, Shield Cup

D. Parts - In - Place (PIP)

Torch has built-in switch.

12 vdc circuit rating

E. Type Cooling

Combination of ambient air and gas stream through

torch.

F. Torch Ratings

SL40 Torch Ratings

Ambient

Temperature

104° F

40° C

Duty Cycle 100% @ 40 Amps @ 193 scfh

Maximum Current 40 Amps

Voltage (V

peak

) 500V

Arc Striking Voltage 500V

Torch Control Circuit

Voltage

24V

G. Current Ratings

SL40 Current Ratings

SL40 Torch & Leads

Up to 40 Amps, DC,

Straight Polarity

NOTE

Power Supply characteristics will determine

material thickness range.

H. Gas Requirements

SL40 Torch Gas Specications

Gas (Plasma and Secondary) Compressed Air

Minimum Input Pressure

85 psi

5.9 bar

Maximum Input Pressure 125 psi / 8.6 bar

Gas Flow

193 scfh

91 lpm

WARNING

This torch is not to be used with oxygen (O

This torch is not to be used with high frequency

starting systems.

CUTMASTER 42

INTRODUCTION 2T-2 Manual 0-5141

2T.03 Introduction to Plasma

A. Plasma Gas Flow

Plasma is a gas which has been heated to an extremely

high temperature and ionized so that it becomes electri-

cally conductive. The plasma arc cutting and gouging

processes use this plasma to transfer an electrical arc

to the workpiece. The metal to be cut or removed is

melted by the heat of the arc and then blown away.

While the goal of plasma arc cutting is separation of

the material, plasma arc gouging is used to remove

metals to a controlled depth and width.

In a Plasma Cutting Torch a cool gas enters Zone B,

where a arc between the electrode and the torch tip

heats and ionizes the gas. The main cutting arc then

transfers to the workpiece through the column of

plasma gas in Zone C.

By forcing the plasma gas and electric arc through a

small oriﬁce, the torch delivers a high concentration

of heat to a small area. The stiff, constricted plasma

arc is shown in Zone C. Direct current (DC) straight

polarity is used for plasma cutting, as shown in the

illustration.

Zone A channels a secondary gas that cools the torch.

This gas also assists the high velocity plasma gas in

blowing the molten metal out of the cut allowing for a

fast, slag - free cut.

A-00002

Workpiece

Power

Supply

Typical Torch Head Detail

B. Gas Distribution

The single gas used is internally split into plasma and

secondary gases.

The plasma gas owsinto thetorchthrough the

negative lead, through the starter cartridge, around

the electrode, and out through the tip oriﬁce.

Thesecondarygasowsdownaroundtheoutside

of the torch starter cartridge, and out between the tip

and shield cup around the plasma arc.

C. Pilot Arc

When the torch is started a pilot arc is established

between the electrode and cutting tip. This pilot

arc creates a path for the main arc to transfer to the

work.

D. Main Cutting Arc

DC power is also used for the main cutting arc. The

negative output is connected to the torch electrode

through the torch lead. The positive output is con-

nected to the workpiece via the work cable and to the

torch through a pilot wire.

E. Parts - In - Place (PIP)

The torch includes a 'Parts - In - Place' (PIP) circuit.

When the shield cup is properly installed, it closes

a switch. The torch will not operate if this switch is

open.

Torch Trigge

PIP Switch

Shield Cup

To Control

Cable Wiring

Torch Switch

A-09595

Parts - In - Place Circuit Diagram for Hand Torch

Page is loading ...

Thermal Dynamics 42 CUTMASTER Operating instructions

Brand: Thermal Dynamics

Model: 42 CUTMASTER

Category: Welding System

Type: Operating instructions

Download PDF

report

in other languages

français: Thermal Dynamics 42 CUTMASTER Mode d'emploi

Thermal Dynamics 42 CUTMASTER Operating instructions

Thermal Dynamics 42 CUTMASTER Operating instructions

in other languages

Related papers

Other documents