LG LN-C060BSA0 Installation guide

Brand: LG

Model: LN-C060BSA0

Type: Installation guide

LG LN-C060BSA0 is a ducted (central) split type air conditioner that offers efficient and reliable cooling and heating solutions for your home or office. With its advanced features and capabilities, this air conditioner is designed to provide optimal comfort and convenience.

The LG LN-C060BSA0 boasts a powerful cooling capacity, ensuring quick and efficient cooling even in large spaces. It also features an energy-efficient design, helping you save on energy costs while maintaining a comfortable indoor environment.

This air conditioner comes equipped with a range of user-friendly features, including a wireless remote control for convenient operation from anywhere in the room. The automatic swing function ensures even distribution of air throughout the space, eliminating hot or cold spots.

ENGLISH

DUCTED(CENTRAL) SPLIT TYPE AIR

CONDITIONERS INSTALLATION INSTRUCTIONS

• Please read this instruction sheet completely before installing the product.

• When the power supply location is wanted to replace, replacement work shall be performed by

authorized personnel only.

• Installation work must be performed in accordance with national wiring standards by authorized

personnel only.

P/No.: 3828A20834B

Air outlet vents

Control box

access panel

Air Intake vents

Thermostat

Air intake

vents

Air outlet vents

Piping

Connecting

wire

Control cover

Main power

(Side)

(Rear)

Air outlet

vents

Air intake

vents

Connecting wire

Connection pipe

Control cover

Main power

(Side)

(Rear)

Air intake vents

Air outlet vents

Piping

Drain hose

Connecting wire

Control cover

Indoor Unit

Outdoor Unit

ENGLISH

1.The following should be always observed for safety.............................3

2. Installation of Indoor, Outdoor Unit .......................................................4

3. Dimensional Data ....................................................................................5

4. One Unit-4 Applications ..........................................................................6

5. Ductwork ..................................................................................................7

6. Condensate Drain Piping ........................................................................7

7. Connecting Pipes to the Indoor Unit .....................................................8

8. Connecting Cables ................................................................................10

9. Start-up Pre-start Quick check list .......................................................13

10. Final installation Checklist and Maintenance .....................................14

TABLE OF CONTENTS

ENGLISH

1. The following should be always observed for safety

• Please report to or take consent by the supply authority before connecting to the system.

• Be sure to read "THE FOLLOWING SHOULD BE ALWAYS OBSERVED FOR SAFETY" before

installing the air conditioner.

• Be sure to observe the cautions specified here as they include important items related to safety.

• The indications and meanings are as follows.

• After reading this manual, be sure to keep it together with the owner's manual in a handy place .

Could lead to death, serious injury, etc.

Do not install it yourself (customer).

Perform the installation securely referring to the

installation manual.

Install the unit securely in a place which can bear the

weight of the unit.

Perform electrical work according to the installation

manualandbesuretouseanexclusivecircuit.

Attach the electrical part cover and service panel to

the unit securely.

Be sure to use the part provided or specified parts for

the installation work.

Check that the refrigerant gas do not leak after

installation is completed.

Bodily injury can result from high voltage electrical

components or fast moving fan drives. For protection

from these inherent hazards during installation and

servicing, the electrical supply must be disconnected. If

operating checks must be performed with the unit

operating, it is the technician's responsibility to

recognize these hazards and proceed safely.

UNIT CONTAINS AN HCFC (R-22) REFRIGERANT

Section 608 paragraph C of the 1990 Clean Air Act states:

Effective July 1, 1992 it shall be unlawful for any person, in the

course of maintaining, servicing, repairing or disposing of an air

conditioning system, to knowingly vent or release any CFC or

HCFC refrigerant minimal releases (air purges of refrigerant

hoses) associated with good faith attempts to recapture or

recycle are exempted from the ban on venting.

Use the specified wires to connect the unit and the

field installed cut off switch box securely and attach

the wires firmly to the terminal so the stress of the

wires is not applied to the sections.

• Incomplete installation could cause injury due to fire, electric shock

or leakage of water. Consult the dealer from whom you purchased

the unit or special installer.

• Incomplete installation could cause a personal injury due to

fire, electric shock, noisy operation or distortion.

• When installed in an insufficient strong place, noisy operation

and distortion could occur.

• Incomplete connecting and fixing could cause fire.

• If the capacity of the power circuit is insufficient or there is incomplete

electrical work, it could result in a fire or an electric shock.

• The use of defective parts could cause an injury or leakage of

water due to a fire, electric shock etc.

• If the electrical part cover panel are not attached securely, it

couldresultinafireorelectricshockduetodust,wateretc.

Could lead to serious injury in particular environments when operated incorrectly.

WARNING

CAUTION

Having perfect vacuum process in the factory, our units don't have drier but have filter in

the refrigerant circuit.

In case of recharging R-22 gas in the field,

"DRIER" must be installed on the liquid line which is connected

from discharge part of condenser to intake part of evaporator. Because the refrigerant

circuit is capable of containing water with imperfect vacuum.

CAUTION

1. Inspection

1) Check for damage after unit is unloaded.

Report promptly, to the carrier, any damage

found to unit. Do not drop unit.

2) Check the unit nameplate to determine if the

unit voltage is correct for the application.

Determine if adequate electrical power is

available. Refer to the application

specifications.

3) Check to be sure the refrigerant charge has

been retained during shipment.

2. Asemble the airfilter and filter

cover.

(Fig. 1)

3. Selection of the best location

1) Indoor unit

Install the air conditioner in the location that

satisfies the following conditions.

• The place shall easily bear a load exceeding

four times the indoor unit’s weight.

• The place shall be able to inspect the unit as

the figure.

• The place where the unit shall be leveled.

• The place shall allow easy water drainage.

• The place shall easily connect with the

outdoor unit.

• The place where the unit is not affected by an

electrical noise.

• The place where air circulation in the room will

be good .

• There should not be any heat source or steam

near the unit.

Suggested airflow clearances and service

clearances are given in. (Fig. 2)

2) Outdoor unit

• If an awning is built over the unit to prevent

direct sunlight or rain exposure, be careful

that heat radiation from the condenser is not

restricted.

• There should not be any animals or plants

which could be affected by hot air

discharged.

• Ensure the spaces indicated by arrows from

the wall, ceiling, fence or other obstacles.

Suggested airflow clearances and service

clearances are given in.(Fig. 3)

2. Installation of Indoor, Outdoor Unit

Filter cover

Air fiter

Clearance 12"

Clearance 36"

GroundGround

Clearance 14"Clearance 14"

Clearance 12"

Clearance 12"Clearance 12"

CLEARANCE 12"

CLEARANCE 28"CLEARANCE 28"

CLEARANCE 20"CLEARANCE 20"

CLEARANCE 36"

CLEARANCE 36"CLEARANCE 36"

CLEARANCE 36"CLEARANCE 36"CLEARANCE 36"CLEARANCE 36"

3RT

3RT 4RT/5RT

4RT/5RT

CLEARANCE 36"CLEARANCE 36"CLEARANCE 36"

CLEARANCE 36"CLEARANCE 36"

CLEARANCE 36"

CLEARANCE 36"CLEARANCE 36"

CLEARANCE 36"

CLEARANCE 20"CLEARANCE 20"

CLEARANCE 12"

CLEARANCE 28"CLEARANCE 28"

(Side Discharge)

(Top Discharge)

Fig. 1

Fig. 2

Fig. 3

1. Indoor unit

Unit Dimensions

2. Outdoor unit

Unit: inch(mm)

ENGLISH

3) Piping length and the elevation

3. Dimensional Data

• If LN-0320CC/AC, LN-0321CC/AC Model is

installed at a distance of 15m, 560g of refrigerant

should be added (15-7) x 70g = 560g

• Capacity is based on standard length and

maximun allowance length is on the basis of

reliability.

3RT 5/8" 3/8" 7.5 25 7.5 15 70

4RT 3/4'' 3/8" 7.5 30 7.5 20 100

5RT 3/4'' 1/2'' 7.5 30 7.5 20 100

Model

Gas Liquid

Standard

Max.

Standard

Max.

Elevation B(m)

Length A(m)

* Additional

refrigerant

(g/m)

Pipe Size

(Diameter: Ø)

Indoor unit

Outdoor unit

Outdoor Unit below

Indoor unit

Gas line

Liquid line

10Cm

Outdoor unit

Must be above top of

condenser coil

Oil trapOil trap

at each 10m

Outdoor Unit above

27.2"(691)

33.7"(855)

28.4"(722)

31.5"(800)

21.5"(546)

12.6"(320)

34.3"(870)

3RT 4RT/5RT

Filter Provision

Liqid lineLiquid line

Condensate

Drain-Upflow

3/4" NPT-Female

Condensate

Drain-Horizonta

3/4" NPT-Fema

Suction lineSuction line

35.4"(900)

48.2"(1,225)

14.6"(370)

MODEL 3RT 4RT / 5RT

A 18.5 (470) 23.6 (600)

B 18.9 (480) 19.7 (500)

C 39.9 (1014) 44.7 (1135)

D 3.3 (84) 5.4 (136)

E 11.9 (303) 13.0 (329)

F 5.6 (142) 7.1 (181)

G 12.0 (304) 12.6 (319)

H 0.6 (15) 0.6 (15)

I 4.3 (110) 6.7 (170)

J 6.3 (160) 9.4 (240)

K 1.7 (43) 2.5 (64)

L 2.0 (50) 2.8 (71)

M 2.0 (52) 2.3 (58)

N 1.8 (45) 2.1 (54)

P 1.3 (32) 1.5 (38)

Q 8.7 (221) 11.2 (285)

R 19.1 (485) 23.0 (584)

Unit: inch(mm)

1. Type of applications

2. How to rotate

• Remove access lower panel and

coil/drain pan.

• Remove bracket point "B" and relocate to

point "A". It is to be rotated 180 degrees.

• Place the coil/drain pan assembly into the

bracket.

• Rotate access lower panel 180 degrees

to match the tubing and drain

connections and assemble.

Motor

Lower Panel

Coil

Drain Pan

Upper Discharge

(as shipped)

Horizontal Right Discharge

(One-step conversion)

Horizontal Left Discharge

(Rotate coil)

Counterflow Discharge

(One-step conversion)

Motor

Point B

Point A

Bracket

4. One Unit -4 Applicalions

ENGLISH

Connections to the unit should be made with three-inch canvas connectors to minimize noise and

vibration transmission.

Elbows with turning vanes or splitters are recommended to minimize air noise and resistance.

The first elbow in the ductwork leaving the unit should be no closer than three times blower diameter to

avoid turbulence and back pressure.

5. Ductwork

A 3/4 inch female condensate drain connection is located on the corner of the unit. A trap should be

installed and filled with water before starting the unit to avoid air from being drawn through. Follow local

codes and standard piping practices when running the drain line. Pitch the line downward, away from

the unit, and avoid long horizontal runs.

Do not use reducing fittings in the drain lines.

The condensate drain must be:

1. Made of 3/4" pipe size.

2. Pitched 1/4" per foot to provide free drainage to convenient drain system.

3. Trapped

4. Must not be connected to closed drain system.

6. Condensate Drain Piping

Cleanout

Plug

Static pressure

Drain Pan

3/4 Inch Male

Panel Enclosure

1.5 Inches1.5 Inches

1. Preparation of Piping

7. Connecting Pipes to the Indoor Unit

Main cause of gas leakage is defect in

flaring work. Carry out correct flaring work

in the following procedure.

1) Cut the pipes and the cable.

■ Use the accessory piping kit or the pipes

purchased locally.

■ Measure the distance between the

indoor and the outdoor unit.

■ Cut the pipes a little longer than

measured distance.

■ Cut the cable 1.5m longer than the pipe

length.

2) Burrs removal

■ Completely remove all burrs from the cut

cross section of pipe/tube.

■ Put the end of the copper tube/pipe to

downward direction as you remove burrs

in order to avoid to let burrs drop in the

tubing.

3) Putting nut on

■ Remove flare nuts attached to indoor

and outdoor units, than put them on

pipe/tube having completed burr

removal.

(Not possible to put them on after flaring

work)

4) Flaring work

■ Carry out flaring work using flaring tool

as shown below.

Firmly hold copper tube in a bar(or die) as

indicated dimension in the table above.

5) Check

■ Compare the flared work with figure.

■ If flare is noted to be defective, cut off

the flared section and do flaring work

again.

Copper

tube

90°

Slanted Uneven Rough

Pipe

Reamer

Point down

Flare nut

Copper tube

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

Inclined

Inside is shining without scratches.

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper flaring =

Outside Diameter

"A"

Gas Liquid Gas

Liquid

5RT

3/4" 1/2" 1.0~1.3 0.5~0.8

4RT

3/4" 3/8" 1.0~1.3 0.5~0.8

3RT

5/8" 3/8" 0.8~1.0 0.5~0.8

Model

ENGLISH

6) Pipe bending

Annealed copper pipe with small diameter (ø6.35 or ø9.52) can be easily bent manually. In

this case, secure large R(radius) for the bend section and gradually bend pipe. If annealed

copper pipe is large in diameter (ø15.88 or ø19.05), bend pipe with bender. Use bender

appropriate for the pipe diameter.

Brazing

In refrigerant piping, bending (in particular, acute bending) must be minimized to reduce

piping resistance. Bending is, however, necessary in some places by virtue of the installation

position of devices auxiliary to the packaged air conditioner, or of the building structure,

piping distance or finsishing appearance. If a more acute bend is required than that

attainable by pipe bender, perform brazing using ready-made elbow. Aside from this

function, brazing also serves to connect straight pipes, generally using ready-made sockets.

While brazing, protect piping against heat with wet cloth to avoid damaging valve packing or

burning thermal insulator with burner heat. While brazing, blow inert gas (nitrogen gas or

carbonic gas) to prevent formation of oxidation film in copper piping; otherwise, the

refrigerant circuit will clog. The blowing of nitrogen gas (or carbonic gas) through 3-way

valves is described in the following:

Refrigerant piping(Flare piping)

When connecting piping, be sure to keep piping dry(keep piping away from water), clean

(keep piping away from dust) and airtight (avoid refrigerant leakage).

When connecting piping on rainy days or making a through-hall in wall, take due care to

prevent water or plaster from entering piping.

CAUTION

a. This procedure is designed to prevent

formation of oxidation film by filling piping

with inert gas. Note that excessive gas

pressure will generate pinholes at brazed

points.

(Nitrogen gas: Supply pressure

0.05~0.1kg/cm

b. When supplying inert gas, be sure to open

one end of piping.

Water enters Plaster enters

Make sure that there is no clearance here.

Overlap with thermal

insulator for piping.

Thermal insulator for refrigerant pipe

(Local supply)

Thermal insulator for

piping(Local supply)

Hose crip for thermal insulator(Local supply)

Torque wrench

Indoor unit tubing

Spanner (fixed)

Tighten the flare unt with a wrench

Connection pipe

Flare nut

2. Connecting of Piping

The Main cable connected to the outdoor unit should be

complied with the following specifications (Rubber

insulation, type H05RN-F approved by HAR or SAA).

The connecting cable connected to the indoor and outdoor

unit should be complied with the following specifications

(Rubber insulation, type H05RN-F approved by HAR or SAA).

CAUTION

20mm

GN/YL

NORMAL

CROSS-SECTIONAL

AREA 0.75mm

20mm

GN/YL

MODEL

3RT

4RT

5RT

MODEL

14mm

NORMAL CROSS-SECTIONAL AREA

If the supply cord is damaged, it must be replaced by a special cord or assembly availible from the manufacturer

of its service agent.

Make sure that the screws of the terminal are free from looseness.

WARNING

■ Connect the wires to the terminals on the control board individually according to the

outdoor unit connection.

• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as

those of indoor unit respectively

Outdoor

Indoor

Main

power source

Switch box

Circuit breaker

• Connecting cable • Main cable

Main power

Terminals on the indoor unit

1(L) 2(N)

Terminals on the outdoor unit

1(L) 2(N)

(220~)

1(L) 2(N)

8. Connecting Cables

• All wiring must comply with local

requirements.

• Select a power source that is capable of

supplying the current required by the air

conditioner.

• Use a recognized circuit breaker

between the power source and the unit.

A disconnection device to adequately

disconnect all supply lines must be

fitted.

• Capacity of circuit breaker

MODEL Capacity

3RT 35A

4RT 50A

5RT 50A

ENGLISH

1) Connecting cable to the

Indoor Unit

• Remove the front panel upper for

electrical connection between the

indoor and outdoor unit.(Remove eight

screws ➀.)

• Connect thermastat cable.

• See wiring diagram for details.

Connection cord

between the indoor unit

and the outdoor unit

Connection cable

between the indoor unit

and the outdoor unit

Control panelControl panel

Front panel

Thermostat cordThermostat cable

2) Connecting cable to the

Outdoor Unit

1. Remove the Cover control from the unit

by loosening a screw.

Connect the wires to the terminals on

the control board individually as

following.

2. Secure the cable onto the control board

with the holder (clamper).

3. Refix the cover control to the original

position with the screw.

Cover control

Terminal block

Cord Clamper

Connecting cableConnecting cable

Main power cableMain power cable

THERMOSTAT

LOW VOLTAGE

TERMINAL BLOCK

Live

Fan

Comp

Heater

3) Form the pipig

• Tape the Pipings and Connecting cable

from bottom to top.

• Form the pipings gathered by taping

along the exterior wall, and make the trap

prevent water from entering into the

room.

• Fix the pipings onto the wall by saddle or

equivalent.

In case of the Outdoor Unit being installed

above position of the Indoor Unit.

Seal a small opening

around the pipings

with gum type sealer.

Trap

CAUTION

After the confirmation of the above conditions, prepare the wiring as follows:

1) Never fail to have an individual power specialized for the air conditioner. As for the

method of wiring, be guided by the circuit diagram pasted on the inside of control

box cover.

2) Provide a circuit breaker switch between power source and the unit.

3) The screw which fasten the wiring in the casing of electrical fittings are liable to

come loose from vibrations to which the unit is subjected during the course of

transportation. Check them and make sure that they are all tightly fastened. (If

they are loose, it could give rise to burn-out of the wires.)

4) Specification of power source

5) Confirm that electrical capacity is sufficient.

6) Be sure that the starting voltage is maintained at more than 90 percent of the

rated voltage marked on the name plate.

7) Confirm that the cable thickness is as specified in the power sources

specification.

(Particularly note the relation between cable length and thickness.)

8) Never fail to equip a leakage breaker where it is wet or moist.

9) The following troubles would be caused by voltage drop-down.

• Vibration of a magnetic switch, damage on the contact point there of, fuse breaking,

disturbance to the normal function of a overload protection device.

• Proper starting power is not given to the compressor.

ENGLISH

9. Start-Up Pre-Start Quick Check List

Bodily injury can result from high voltage electrical components. If operating checks must be

performed with the unit operating, it is the technician's responsibility to recognize these hazards

and proceed safely. Failure to do so could result in severe personal injury or death due to

electrical shock or contact with moving parts.

WARNING

• Is unit level and located with proper clearances?

• Is the duct work correctly sized, run, taped, insulated and

weather proofed with proper unit arrangement?

• Is condensate line properly sized, run trapped and pitched?

• Is the filter of the correct size, clean and in place?

• Is the wiring properly sized and run in according to the unit

wiring diagram?

• Are all wiring connections tight including those in unit and

compressor electrical boxes?

• Has the unit been properly grounded and fused with the

recommended fuse size?

• Have the air conditioning systems been checked at the

service ports for charge and leak tested if necessary?

• Does the condenser fan and indoor fan turn freely without

rubbing and are they tight on the shafts?

• Visually inspect the unit to ensure that the airflow required

for the condenser coil is not obstructed from the unit.

• Inspect the control panel wiring to verify that all electrical

connections are tight, and that wire insulation is intact.

• Has the indoor fan speed been determined and the proper

speed been set?

• Has all work been done in accordance with applicable local

and national codes?

• Are all covers and access panels in place to prevent air loss

and safety hazards?

You can do some of the periodic maintenance functions for your unit yourself; this includes

cleaning air filters, cleaning unit cabinet, cleaning the condenser coil, and conducting a

general unit inspection on a regular basis.

It is very important to keep the central duct system air filters clean. Be sure to inspect them

at least once each month when the system is in constant operation. (In new buildings, check

the filters every week for the first 4 weeks.)

Permanent type filters can be cleaned by washing with a mild detergent and water. Ensure

that the filters are thoroughly dry before reinstalling them in the unit (or duct system).

Before removing access panels to service unit, disconnect power supply. Failure to

disconnect power before attempting any servicing can result in severe injury or death.

WARNING

10. Final Installation Checklist and Maintenance

• Is the condenser fan and indoor blower operating correctly, with proper rotation and

without undue noise?

• Are the compressors operating correctly and has the system been checked with a

charging chart?

• Have voltage and running currents been checked to determine if it is within limits?

• Have the air discharge grilles been adjusted to balance the system?

• Has the ductwork been checked for air leaks and condensation?

• Has the indoor airflow been checked and adjusted if necessary?

• Has the unit been checked for tubing and sheet metal rattles and are there unusual

noises to be checked?

• Are all covers and panels in place and properly fastened?

• Has the owner or maintenance personnel been given this manual, warranty, and been

instructed on proper operation and maintenance?

Routine Maintenance By Owner

Air Filters

ENGLISH

Unfiltered air circulates through the unit's condenser coil and can cause the coil's surface to

become clogged with dust, dirt, etc.. To clean the coil, vertically (i.e., along the fins) stroke

the coil surface with a soft bristled brush.

Keep all vegetation away from the condenser coil area.

To keep your unit operating safely and efficiently, the manufacturer recommends that a

qualified serviceman check the entire system at least once each year, or more frequently if

conditions warrant. Your serviceman may examine these areas of your unit:

Complete the unit inspections and service routines described below at the beginning of each

heating season.

Inspect the control panel wiring to verify that all electrical connections are tight and wire

insulation is intact.

To prevent injury or death due to electrical shock of contact with moving parts, lock unit

disconnect switch in open position before servicing unit.

To prevent an explosion and possible injury, death and equipment damage, do not store

combustible materials, gasoline or other flammable vapors and liquids near the unit.

WARNING

Condenser coil

Maintenance Performed by Serviceman-Cooling Season

Maintenance Performed By Serviceman-Heating Season

1. Filters

2. Motors and drive system components

3. Condenser coils

4. Safety Controls

5. Electrical components and wiring

6. Condensate drain

7. Inspect the unit duct connections to ensure they

are physically sound and sealed to the unit casing.

8. Inspect the unit mounting support to see that it is

sound.

9. Inspect the unit to ensure there is no obvious

deterioration.

➔ For cleaning

➔ For mechanical cleaning

➔ For possible replacement or

connection tightness

➔ For cleaning

LG LN-C060BSA0 Installation guide

LG LN-C060BSA0 Installation guide

LG LN-C060BSA0 Installation guide

Related papers

Other documents