Contec IPC-POAW/10-01 Owner's manual

IPC-POAW/10-01 1

10VDC Power Unit for IPC Series

(100-240VAC Input)

IPC-POAW/10-01

User’s Guide

CONTEC CO.,LTD.

Thank you for purchasing the IPC-POAW/10-01 power supply unit.

The IPC-POAW/10-01 is the dedicated power supply unit for the following CONTEC Computer.

Box Computer: IPC-BX/M360(PCI) Series

WARNING

Indicates dos and don'ts that are assumed to result in possible death or serious injury if they are

inappropriately handled ignoring this icon.

- Do not use the product in locations exposed to a flammable or corrosive gas. It may cause explosion,

fire, electrical shock, or malfunction.

- If you sense abnormality (smoke, odor, or noise), immediately unplug the power cord from the wall

outlet and contact the CONTEC sales representative or sales office.

- To avoid electrocution do not use the product with a wet hand.

- Prevent foreign matters (such as metal pieces, combustibles, and liquids) from penetrating into the

product through ventilation holes, for example, to prevent a fire or electrical shock.

- Be sure to connect the product to the stipulated power supply voltage. Connecting to a different

voltage might cause a fire or electrical shock.

- Be sure to ground the product.

- Never disassemble or modify the product or replace its parts in order to prevent electrical shock,

fire, or malfunction. CONTEC reserves the right to refuse servicing the product modified by the

user. When any part of the product needs to be replaced at the expiration of its life or due to

breakdown, please contact the CONTEC sales representative or sales office.

IPC-POAW/10-01

2

IPC-POAW/10-01

CAUTION

Indicates dos and don'ts that are assumed to result in possible injury or property damage if they are

inappropriately handled ignoring this icon.

- Use the product in the stipulated operating environment (temperature and humidity).

- When installing the product, be sure to disconnect the power cable.

- Do not use or store the product in a location exposed to extremely high or low temperature or

susceptible to a rapid temperature change. Example:

- Exposure to direct sun

- In the vicinity of a heat source

- To clean the product wipe it gently with soft cloth damp with either water or mild detergent.

Do not use chemicals or a volatile solvent, such as benzene and thinner, to prevent peeling or

discoloration of the paint.

- Avoid installation that blocks ventilation holes. Blocking contains heat inside the product causing it

to malfunction or break down.

- CONTEC is not liable for the product that has been modified by the user.

- When transporting the product, provide adequate measures to protect it from vibration or shock.

- Estimated life is about 10 years based on continual operation at 40°C (Horizontal installation).

However, (higher) operating temperatures will result in shorter life.

FCC PART 15 Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference at his own expense.

NOTE

Change or modifications not expressly approved the manufacturer can void the user's authority to

operate this equipment.

WARNING TO USER

IPC-POAW/10-01

IPC-POAW/10-01 3

Features

- No extra installation work is necessary since the unit can be installed directly.

- A broad continuous input voltage range of 100-240VAC.

Package Contents

The product you have purchased consists of the following items. Be sure that you have them all. If you

find any item either missing or damaged, please contact the sales representative you purchased the

product from.

- Power supply unit…1 - Set Angle…4

- AC power cable…1 * - Set Screw…8

- Connection cable (for IPC-BX/M360(PCI) series)…1

- User’s Guide (this document)…1

* This AC power cable is for the voltage of the 125VAC or less. In the case that the voltage that this

cable uses do not match you need to prepare other cable particularly.

External Dimensions and Component Identification

<IPC-BX/M360(PCI)C>

Power switch

AC terminal block

DC connector

LN

V+V-FG

10VDC-OUT

146

38 11 157

[mm]

10VDC -OUT

V+

N L

FG V-

PCM CIA

LAN2

SERIAL1

ACT

SERIAL2

USB

LNK

ACT

LNK

LAN1

DC-IN FG V- V+

KBDVI

ACCESSPWR

SPD

RAS

SPK

RST

107

IPC-POAW/10-01

4

IPC-POAW/10-01

Power Connection

Connector type +10VDC output connector Model

DFK-MC1,5/3-GF-3,81

(PHONIX CONTACT)

Pin No. Signal name

1FG

2GND

123

3 10V

AC Connection

Connector

type

100 to 240VAC input

connector

Model W168A-3P-C (World)

Pin No. Signal name

1FG

2N

123

3L

Installation Procedure

First be sure that the power switch of the power supply unit is set to off and then connect the power

supply unit DC cable to the connector of Computer.

(Bundled)

DC cable

Set Angle

IPC-POAW/10-01

Set Screw

IPC-BX/M360(PCI)Cxxx

Connect the terminals L, N, and on the voltage input terminal strip to the live line , neutral line, and

ground, respectively. (M3.5x7 Screw is used, Terminal outside : 7.2mm or less)

IPC-POAW/10-01

IPC-POAW/10-01 5

Installation Requirements

The BOX-PC can be installed in any orientation (1) through (3). (with the IPC-BX/M360(PCI)C Set

Angle mounted)

Front

Thickness : 2.3mm

(1)

V+V-FG

LN

10VDC-OUT

SPD

DC-IN

PWR ACCESS

PCMCIA

ACT

SERIAL2

LAN2

ACT LNK LNK

LAN1

RAS

SERIAL1 USB DVI

RST

V+V-FG

KB SPK

190

170

10

10.5 120

[mm]

16

5

R5.5

R2.5

2.3 102

146

(2)

120

140

10

[mm]

16

5

R5.5

R2.5

10.5 120

Front

IPC-POAW/10-01

6

IPC-POAW/10-01

LN

FG V+V-

10VDC-OUT

DC-IN

SPD

LAN1LAN2

ACT

SERIAL2

ACT L NK LNK

RAS

PCMCIA

PWR ACCESS

V+V-FG

RST

SERIAL1 USB DV I SPKKB

[mm]

16

5

R5.5

R2.5

(3)

IPC-POAW/10-01

IPC-POAW/10-01 7

Specifications

Requirement Description

Power supply specs

Rated input voltage 100VAC to 240VAC (continuous input), 50/60Hz

Rated input current AC IN 100V : 1.6A (Max.)

AC IN 200V : 0.8A (Max.)

Rated output voltage +10VDC

Rated output current 3.0A (Max.)

Permissible momentary blackout 20ms (AC IN 100V, Io=100%, (Typ.))

Dielectric strength

(between Input and FG)

2.0kVAC for one minute

Insulation resistance

(between input and FG)

Greater than 50M

Ω (500VDC)

Environmental specs

Operating temperature 0 to 45°C

Storage temperature -20 to 75°C

Humidity 20 to 85%RH (No condensation)

Floating dust particles Not to be excessive

Corrosive gases None

Line-Noise

resistance

Line-noise AC line/2kV, Signal line/1kV (IEC1000-4-4Level 3, EN61000-4-4Level 3)

(HOST: IPC-BX/M360(PCI), FPD: IPC-DT/H20X(PC)T)

Static

electricity

resistance

Contact discharge/4kV (IEC1000-4-2Level 2, EN61000-4-2Level 2)

Atmospheric discharge/8kV (IEC1000-4-2Level 3, EN61000-4-2Level 3)

(HOST: IPC-BX/M360(PCI), FPD: IPC-DT/H20X(PC)T)

Vibration

resistance

Sweep

resistance

10 to 57Hz/semi-amplitude 0.15mm, 57 to 150Hz/2.0G

40 minutes each in X, Y, and Z directions

(JIS C0040-compliant, IEC68-2-6-compliant)

Impact resistance 10G, half-sine shock for 11ms in X, Y, and Z directions

(JIS C0041-compliant, IEC68-2-27-compliant)

Construction

External dimensions (mm) 146(W)x157(D)x38(H)

Weight 900g(Cable not included)

2.4kg(IPC-BX/M360(PCI)C[With no HDD]) and Set Angle(M360’s)

included)

IPC-POAW/10-01

8

IPC-POAW/10-01

Copyright

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this

document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an

omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may

appear in this document nor for results obtained by the user as a result of using this product.

Limited One-Year Warranty

CONTEC IPC Series are warranted by CONTEC CO., LTD to be free from defects in material and

workmanship for up to one year from the date of purchase by the original purchaser.

Repair will be free of charge only when this device is returned freight prepaid with a copy of the original

invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from

which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and

original boards. The warranty is not applicable if the device has been tampered with or damaged through

abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which

case repairs will be considered beyond the warranty policy.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please

obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you

purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor

be liable for any incidental or consequential damages due to such defect or consequences that arise from

inexperienced usage, misuse, or malfunction of this device.

IPC-POAW/10-01

CONTEC CO., LTD. January 2005 Edition

3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan

Japanese http://www.contec.co.jp/

English http://www.contec.com/

Chinese http://www.contec.com.cn/

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD. [01112005]

[06162004] Management No. A-46-880

[01112005_rev2] Parts No. LYDW241

Contec IPC-POAW/10-01 Owner's manual

Contec IPC-POAW/10-01 Owner's manual

Related papers

Other documents