Perel SCAMSET8N User manual

SCAMSET8N

USER MANUAL 2

HANDLEIDING 19

MODE D'EMPLOI 36

MANUAL DEL USUARIO 53

BEDIENUNGSANLEITUNG 70

INSTRUKCJA OBSŁUGI 87

MANUAL DO UTILIZADOR 104

SCAMSET8N

V. 01 – 31/10/2018 2 ©Velleman nv

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle

could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal

waste; it should be taken to a specialized company for recycling. This device should be

returned to your distributor or to a local recycling service. Respect the local environmental

rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Perel! Please read the manual thoroughly before bringing this device

into service. If the device was damaged in transit, do not install or use it and contact your

dealer.

2. Safety Instructions

Read and understand this manual and all safety signs before using this appliance.

Indoor use only.

Class II equipment.

 This device can be used by children aged from 8 years and above, and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning the use of the device in a safe

way and understand the hazards involved. Children shall not play with the device. Cleaning

and user maintenance shall not be made by children without supervision.

 Risk of electroshock when opening the cover. Touching live wires can cause life-threatening

electroshocks. Do not disassemble or open the housing yourself. Have the device repaired

by qualified personnel.

Be very careful during the installation: touching live wires can cause life-threatening

electroshocks.

 Always disconnect mains power when the device is not in use or when servicing or

maintenance activities are performed. Handle the power cord by the plug only.

 There are no user-serviceable parts inside the device. Refer to an authorized dealer for

service and/or spare parts.

 Have the device installed/repaired by a qualified person.

 Do not use the device when damage to housing or cables is noticed. Do not attempt to

service the device yourself but contact an authorised dealer.

SCAMSET8N

V. 01 – 31/10/2018 3 ©Velleman nv

3. General Guidelines

 Refer to the Velleman

®

Service and Quality Warranty on the last pages of this manual.

 All modifications of the device are forbidden for safety reasons. Damage caused by user

modifications to the device is not covered by the warranty.

 Only use the device for its intended purpose. Using the device in an unauthorised way will

void the warranty.

 Damage caused by disregard of certain guidelines in this manual is not covered by the

warranty and the dealer will not accept responsibility for any ensuing defects or problems.

 Nor Velleman nv nor its dealers can be held responsible for any damage (extraordinary,

incidental or indirect) – of any nature (financial, physical…) arising from the possession,

use or failure of this product.

 Keep this manual for future reference.

4. Overview

1

IR LED

6

microphone

2

lens

7

tamper switch

3

speaker

8

reset button

4

CdS photoresistor

9

thread hole

5

doorbell button

SCAMSET8N

V. 01 – 31/10/2018 4 ©Velleman nv

5. Installation

Install the wifi antenna inside the house for the best results.

Please ensure a good wifi signal before installing! Relocate the router or the antenna if

necessary. If the wifi signal is still weak, add a wifi repeater or use a network cable.

Make sure to insert the SD card.

Step 1

Drill a hole for the wires to go through the wall. Loosen the screw at the bottom of the door

phone with the hex screwdriver. Remove the rain cover and stick the rain cover on the wall.

Step 2

Secure the rain cover using two screws.

Step 3

Lead the wires through the hole in the wall. Install the door phone in the rain cover and secure

with the hex screw.

Step 4

Connect the antenna to the door phone and stick the antenna on the wall.

Step 5

Proceed with the connection.

SCAMSET8N

V. 01 – 31/10/2018 5 ©Velleman nv

6. Connection

a

door phone power supply

d

doorbell

b

lock

e

doorbell power supply

c

lock power supply

1

antenna

7

doorbell relay NO (grey)

2

power in DC +12 V (red)

8

RJ45 (orange)

3

power in DC -12 V (black)

9

RJ45 (orange + white)

4

lock relay COM (yellow)

10

RJ45 (green + white)

5

lock relay NO (purple)

11

RJ45 (green)

6

doorbell relay COM (grey)

SCAMSET8N

V. 01 – 31/10/2018 6 ©Velleman nv

7. Installing the App

Download the DIY Smart app from the Google Play or iTunes store, and install it on your

mobile phone. Remember to allow the software to send notifications.

Connect your mobile phone to the same router as the camera’s and register. Make sure to

enable the Open DHCP function on your router.

This system does not support a 5 GHz wifi router. Use a 2.4 GHz wifi router instead.

If two mobile phones use the same account ID to log in, only one mobile phone can receive the

notifications. Therefore, each phone should register as a single account.

1. Click the Register button.

2. Enter your e-mail address and create an account password.

3. Click to register.

After registration, choose one of the setup methods below.

SCAMSET8N

V. 01 – 31/10/2018 7 ©Velleman nv

8. Setup

8.1 SmartLink

Insert the memory card. Also, connect the antenna and the power supply. It takes 30 seconds

to start up.

Do not connect the network cable as the system will not be able to set up a wifi connection in

SmartLink.

1. Enter your e-mail address and password.

2. Click to log in.

3. Click the + button.

4. Choose Add new device.

5. Click SmartLink.

6. Enter the wifi password and click Next.

7. Click Hear a beep for connection when you hear a beeping sound.

8. Turn the volume level of your mobile phone to the maximum. Click Next.

SCAMSET8N

V. 01 – 31/10/2018 8 ©Velleman nv

9. The door phone will emit a beep.

10. Enter the door phone name.

11. Enter the default password 123 and click the Save button to finish.

The door phone will beep three times to indicate a successful connection. Press the reset

button for five seconds on the door phone (see chapter Resetting) and re-connect to SmartLink

if the door phone does not beep.

If the door phone still does not connect to SmartLink, try the AP connection method.

8.2 AP Connection

Insert the memory card. Also, connect the antenna and the power supply. It takes 30 seconds

to start up.

Do not connect the network cable as the system will not be able to set up a wifi connection in

AP connection.

1. Enter your e-mail address and password.

2. Click to log in.

3. Click the + button.

4. Choose Add new device.

5. Click AP connection.

SCAMSET8N

V. 01 – 31/10/2018 9 ©Velleman nv

6. Click Hear a beep for connection when you hear a beeping sound.

7. Enter the passwords and click Next.

8. If you are using an Android

®

phone, click Go to set WiFi.

9. If you are using an iOS

®

phone, go to Settings  WiFi and connect to the network.

10. Return to the app.

11. After the beep, click Already hearing: connect successfully to finish.

SCAMSET8N

V. 01 – 31/10/2018 10 ©Velleman nv

The door phone will beep three times to indicate a successful connection. Press the reset

button for five seconds on the door phone (see chapter Resetting) and retry if the door phone

does not beep.

If the door phone still does not connect, try the wired connection method.

8.3 Wired Connection

Insert the memory card. Also, power the door phone and connect it to the LAN port of the

router using a network cable. It takes 30 seconds to start up.

Make sure the door phone and mobile phone are connected to the same router.

1. Enter your e-mail address and password.

2. Click to log in.

3. Click the + button.

4. Choose Add new device.

5. Click Wired connection.

6. Click the device ID.

7. Enter the door phone name.

SCAMSET8N

V. 01 – 31/10/2018 11 ©Velleman nv

8. Enter the default password 123 and click the Save button to finish.

9. Click All devices  Settings  Network settings and select the wifi network in the list.

10. Enter the wifi password.

Do not select wifi as a network type.

11. Unplug the network cable.

9. Adding other Mobile Phones

In All devices, press + and select Add online device. Enter the mobile phone ID, name and

password.

SCAMSET8N

V. 01 – 31/10/2018 12 ©Velleman nv

To find the mobile phone ID, go to All devices, select the mobile phone and click Edit.

10. Date and Time

Go to All devices  Device  Time settings and select your time zone.

1. Select your time zone.

2. Click Application to confirm.

3. Check if the time zone is correct.

11. Interface

SCAMSET8N

V. 01 – 31/10/2018 13 ©Velleman nv

1

date and time

6

arm/disarm

2

transfer speed

7

talk

3

resolution

8

record

4

mute

9

vertical screen

5

snapshot

10

unlock

1

name

7

snapshot

2

transfer speed

8

mute

3

date and time

9

vertical screen

4

resolution

10

unlock

5

record

11

settings

6

talk

12. Push Notification

A notification will be sent to your phone as soon as the call button or alarm is triggered.

SCAMSET8N

V. 01 – 31/10/2018 14 ©Velleman nv

1. Press (Android

®

) or slide (iOS

®

) to view.

2. The picture will only appear when the mobile phone is loaded with a memory card.

It is important that the app be activated on the mobile phone.

Click to delete the ID which does not need to receive notifications

13. Video Recording and Playback

Step 1

Switch off the power, insert the memory card and switch on the power again. Do not insert or

remove the memory card when the device is switched on.

Step 2

Go to All devices  Device  Record settings  Format card and confirm.

SCAMSET8N

V. 01 – 31/10/2018 15 ©Velleman nv

Step 3

Select Record alarm to record when the call button or alarm is triggered. Also, set the

recording mode and length.

Step 4

To play back a recorded video, go to All devices  Playback and select the video.

14. Modifying a Password

Go to All devices  Device  Security settings  Admin password and modify the

password.

SCAMSET8N

V. 01 – 31/10/2018 16 ©Velleman nv

1. Click Security settings.

2. Click Admin password.

3. Enter the old password, the new password and click Save. Your password must be 6-30

characters long and must include both alphabetic characters and numbers.

15. Deleting a Mobile Phone

1. Press (Android

®

) or slide (iOS

®

) to view.

2. Click Delete.

3. Click Confirm.

16. Resetting

Press and hold the reset button for 5 seconds. The system will restart 30 seconds after the

beep.

SCAMSET8N

V. 01 – 31/10/2018 17 ©Velleman nv

17. Tamper Alarm

When the door phone is removed from its rain cover with evil intent, the tamper switch will be

activated. The system will then send an alarm message to your connected phone.

18. Troubleshooting

I do not receive any notification on my smartphone.

 Make sure the notification function is enabled on the door phone.

 Make sure the app is enabled on your smart phone.

Unclear sound or picture, no sound.

 The network is not stable. Try to change to a broader bandwidth.

 Possibly, too many devices are connected to the same router.

Audio and video delay with long-distance connection.

 The door phone is installed too far from the antenna. Shorten the connection distance or

use a 16 dB antenna instead.

Poor-quality audio on my smartphone.

 Increase the volume level on your smartphone.

I do not receive any notification on my smartphone.

 Make sure the notification function is enabled on the door phone.

 Make sure the app is enabled on your smart phone.

The audio is subject to noise and echo.

 Your smartphone is possible too close to the door phone’s speaker.

I cannot open the door lock.

 Tap the key icon for 3 seconds to unlock the door. Wait for 6 more seconds and retry.

Can I update my app?

 Yes, you can. Go to the system settings page and tap [Update].

Can I update my door phone?

 Yes, go to the device updating page to update to the newest version.

SCAMSET8N

V. 01 – 31/10/2018 18 ©Velleman nv

19. Cleaning and Maintenance

 The device does not need any particular maintenance. However, it is advisable to clean it

occasionally to keep it looking like new.

 Occasionally wipe with a damp cloth. Do not use harsh chemicals, cleaning solvents or

strong detergents.

20. Technical Specifications

camera ...........................................................................................................................

sensor .................................................................................................... 1 megapixel

video quality ......................................................................................... 720p / 30 fps

IR filter ............................................................................................................... yes

night vision distance ............................................................................................ 2 m

viewing angle ..................................................................................... 110° wide angle

audio

2-way audio ................................................................... full duplex (at the same time)

door unlock function ................................................................................ relay output

IP rating ............................................................................................................ IP65

working temperature ........................................................................... -10 °C to 50 °C

dimensions .................................................................................... 128 x 42 x 53 mm

weight ............................................................................................................. 290 g

power supply .............................................................................. 12 VDC, 0.5 A (incl.)

All registered trademarks and trade names are properties of their respective owners and are

used only for the clarification of the compatibility of our products with the products of the

different manufacturers.

RED Declaration of Conformity

Hereby, Velleman NV declares that the radio equipment type [SCAMSET8N] is in compliance

with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

www.velleman.eu.

Use this device with original accessories only. Velleman nv cannot be held

responsible in the event of damage or injury resulting from (incorrect) use of this

device. For more info concerning this product and the latest version of this manual,

please visit our website www.perel.eu. The information in this manual is subject to

change without prior notice.

The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.

No part of this manual may be copied, reproduced, translated or reduced to any electronic

medium or otherwise without the prior written consent of the copyright holder.

Page is loading ...

SCAMSET8N

6. Klik op Hear a beep for connection wanneer u een pieptoon hoort.

7. Geef de wachtwoorden in en klik op Next.

8. Als u een Android

®

telefoon gebruikt, klik op Go to set WiFi.

9. Als u een iOS

®

telefoon gebruikt, ga naar Settings  WiFi en verbind met het netwerk.

10. Keer terug naar de app.

11. Na de pieptoon, klik op Already hearing: connect successfully om te voltooien.

Page is loading ...

SCAMSET8N

8. Introzca la contraseña estándar 123 y haga clic en Save para terminar.

9. Haga clic en All devices  Settings  Network settings y seleccione la red wifi

network en la lista.

10. Introduzca la contraseña de la red wifi.

No seleccione wifi como tipo de red.

11. Desenchufe el cable de red.

9. Añadir otros teléfonos móviles

En All devices, pulse+ y seleccione Add online device. Introduzca el ID del teléfono móvil, el

nombre y la contraseña.

Page is loading ...

Perel SCAMSET8N User manual

Perel SCAMSET8N User manual

in other languages

Related papers

Other documents