stufurhome ST3001MB Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
● We recommend that this product is installed by a qualified professional contractor.
● Please check this product immediately to ensure that it has not been damaged and is complete. Before installation, please make
sure this product is the correct model and you have all the parts required for installation and using.
● Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the taps.
●
Turn off water supply before commencing work, this should be done at the isolating valves of inlet feeds if fitted or main sto
pcock.
● Please read these instructions carefully and keep it for future reference.
Maintainance
We do NOT recommend you use any household cleaners to clean the product. Because these cleaners change substance or formula
too frequently. The product should be always cleaned only with soapy water and rinsed with clean water and dried with a soft cloth.
Important
Cleaning
Before use: Unscrew the Aerator and allow the water to run freely for 5 minutes. Then screw the filter back in place.
Periodically: Unscrew the Aerator and remove. Rinse it with running water until any loose debris is cleared. Then replace the Aerator
and tighten.
Aerator
INSTALLATION
INSTRUCTIONS
Single-lever basin mixer
ST3001CH/AT3001MB
Installation
Dimensions
To remove the cartridge.
First shut off the water supply to the tap.
1: Pull out the cap from the handle.
2: Loosen the grub screw in handle, but do not remove it.
3: Take off the handle, unscrew the cartridge cover.
4: Using a correct size spanner unscrew the retaining nut.
5: Pull the cartridge and wash it with clean running water.
6. Dry and lightly grease the seals (only use silicone grease)
7: Replace them in turn.
1: Fit the O-ring in the underside of the facuet body.
2: Screw the male screw and the flexible hoses into the facuet body, and fully hand tighten.
3: Pass the tail of flexible pipes through the hole on the basin from above, and place the mixer in position on the basin, to see if any
alteration to the existing supply pipe work is necessary, make any necessary alterations to the pipe work.
4: Tighten the rubber washer, the brass washer with the female screw from the under-side of the counter.
5: Check that the mixer body is correctly positioned, fully tighten the female screw.
6:
Connect the water supply pipes to the tail of flexible hoses with the hot water and cold water.
FACUT
CARTRIDGE
HANDLE
CAP
Unit:inches
6.48″
4.12″
4.41″
1.65″
Ø
1.38″
max1.18″
Faucet
Flexible Hose
Male screw
O-ring
Rubber washer
Brass washer
Female screw
Spanner
Lift pole
Drain
Concave
Washer
Metal
washer
Drain off pole
Mounting
Nut
7:
Insert the lift pole through the hole at the back of the faucet body.
8:
Insert the drain through the hole of the basin.attach concave washer, metal washer , and mounting nut to drain .Tighten the drain securely.
Insert shortest end of drain-off pole into drain body . Place the end side of the lift pole through the drain-off pole and then tighten the screw.
-
1
-
2
stufurhome ST3001MB Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
stufurhome ST1100MB Installation guide
-
-
-
-
-
-
-
-
Other documents
-
Fresca FFT1051CH Installation guide
-
-
-
-
-
-
-
-
-