Alecto DC-02 Owner's manual

Type
Owner's manual
GEBRAUCHSANLEITUNG
Montage:
Bestimmen Sie die Stelle, an der die DC-02 montiert wer-
den soll, halten Sie den Montagefuß an diese Stelle und
zeichnen Sie die Bohrlöcher an.
Befestigen Sie die Kamera mit Hilfe der Schrauben..
Ausrichten:
Die Kamera kann + 180° nach unten oder nach oben und
360° nach links oder rechts ausgerichtet werden.
Die Drehkonstruktion arbeitet mit einem Kippmechanismus.
Es müssen deshalb keine Schrauben los oder fest gedreht
werden um die Richtung zu ändern.
Stromversorgung:
DDie blinkende LED an der Vorderseite wird mit 2x 1,5 Volt
Batterien, des Typs AAA, LR03 mit Strom versorgt.
Die Batterien setzen Sie ein oder wechseln Sie, indem
Sie die Kappe an der Rückseite abnehmen und den
Batteriefachdeckel links herumdrehen und abnehmen. .
Benutzen Sie vorzugsweise Alkali Batterien, diese haben
eine längere Lebensdauer. Auch wideraufladbare Batterien
können benutzt werden. Achten Sie beim einsetzen der
Batterien auf die richtige Polarität.
Schalten Sie die DC-02 ein oder aus mit dem Schalter im
Batteriefach. Setzen Sie den Batteriefachdeckel wider auf
und drehen ihn nach rechts, um ihn fest zu setzen.
Leere Batterien nicht in den normalen
Hausmüll werfen, sondern bei einer
Sammelstelle für leere Batterien abgebe.
Funktion:
Durch ein LDR wird jede Änderung des Lichts in der Nähe
der blinkende LED eingeschaltet. Eg. Das Öffnen einer Tür
oder eine Taschenlampe. Wenn es keine Änderung des
Lichts wird, ist die LED aus.
Hinweis:
Die DC-02 ist nur für den In-Door Bereich geeignet.
Reinigen Sie das Gehäuse und das Linsenfenster nur mit
einem leicht feuchten Tuch. Wechseln Sie die Batterien,
wenn die LED nur noch schwach leuchtet oder langsam
blinkt.
Achtung:
Die DC-02 ist eine Dummy Kamera, die nur durch ihre
Form preventief funktioniert.
Die DC-02 kann Einbruch oder Diebstahl nicht verhindern.
Machen Sie es nicht bekannt, dass es sich bei der
Kamera um einen Dummy handelt, dies macht den Effekt,
dieses Produktes zunichte.
USERS MANUAL
Installation:
Decide where to fix the camera and hold the the mounting
plate against the wall. Drill the holes and mount the camera
firmly with the screws provided.
Adjustment:
The camera can be adjusted 180° up/down and 360° left/
right. The turning mechanism works with a knurled ring con-
struction so no need to turn screws.
Power supply:
The flashing LED on the frontside is powered by 2 x 1.5
Volt battery, size AAA, LR03 or MICRO.
Placement or replacement of the batteries should be done
by taking away the cover at the backside, turn the cover
and take away the battery cover. We advise to use Alkaline
batteries for the long life time. Rechargeable batteries can
also be used. Turn the DC-02 OFF and ON with the switch
in the battery compartment. Place back the battery cover
and turn right to fixate.
Do not throw away exhausted batteries
but hand them over to your local depot
of chemical waste.
Operation:
By means of an LDR is any change of light in the vicinity of
the flashing LED is switched on. Eg. Opening a door or shi-
ning a flashlight. If there is no change of light is made, the
LED is off.
Remarks:
The DC-02 is for indoor use only. Only clean the camera
housing and the lense with a soft and moisture cloth.
Replace the battery in case the LED indicator becomes dim.
Attention:
The DC-02 is a dummy camera and only its shape gives it
a preventional function. This camera can never prevent
burglary or theft. Never tell others that the DC-02 is a
dummy camera, this will undo the effect of this camera.
ver. 1.1
Service
Help
Aziëlaan 12
‘s-Hertogenbosch
WWW.HESDO-SERVICE.NL
+31 (0) 73 6411 355
GEREGISTREERD DEELNEMER VAN
www.ictmilieu.nl
y,
es
Pro
du
kt
es
z
u
ni
c
ht
e
.
Montagesockel
mounting base
180°
360°
°
DC-02
  • Page 1 1
  • Page 2 2

Alecto DC-02 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI