Extron SGS 408 User manual

Extron
Brand
Extron
Model
SGS 408
Type
User manual

Extron SGS 408 is a professional-grade DVI connector that allows for the transmission of digital video signals over long distances. It is compatible with Extron DVI transmitters and receivers, and can be used to extend the reach of DVI signals up to 300 feet (91.44 meters) using standard CAT5e/6 cable. The SGS 408 supports resolutions up to 1920x1200, and is perfect for use in a variety of applications, including home theater, conference rooms, and classrooms. With its compact size and easy installation, the SGS 408 is a great way to add flexibility and convenience to your DVI system.

Extron SGS 408 is a professional-grade DVI connector that allows for the transmission of digital video signals over long distances. It is compatible with Extron DVI transmitters and receivers, and can be used to extend the reach of DVI signals up to 300 feet (91.44 meters) using standard CAT5e/6 cable. The SGS 408 supports resolutions up to 1920x1200, and is perfect for use in a variety of applications, including home theater, conference rooms, and classrooms. With its compact size and easy installation, the SGS 408 is a great way to add flexibility and convenience to your DVI system.

User’s Guide
© 2006 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
F
ax +65.6383.4664
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.extron.com
70-122-01 Upgrade Kit
68-535-01 Rev. C
06 06
SGS 408 DVI Connector
5. Attach the power cord to the SGS 408 and to the AC power
source. Make sure the SGS 408 is working correctly.
6. If the SGS 408 is rack mounted, remove the power cable
from the SGS 408 and reattach the SGS 408 to the rack.
Reconnect the power cord and the input and output cables.
Part Numbers
Related part numbers
Extron Part Part Number
DVI transmitter and DVI receiver 60-316-02
SGS 408 DVI Connector • InstallationSGS 408 DVI Connector • Installation
Installation
32
Installing the DVI Connector
The DVI connector card may be installed in the SGS 408 by
following the instructions and illustrations shown below. Before
the DVI connector card can be installed, the internal components
of the SGS 408 must first be accessed.
Internal access
To gain access to the internal components, do the following:
1. Remove the power cable from the SGS 408 and from the
power source.
Do not open the cover of the switcher without unplugging
the power cord.
2. If the SGS 408 switcher is rack mounted, remove the input
and output cables from it and remove the unit from the
rack. If the switcher is not rack mounted, you do not need
to remove the input and output cables.
3. Remove 16 screws from the sides and top of the cover and
two #10 screws from the upper half of the front panel
(figure 1).
Figure 1 — Removing the cover
4. Remove the cover by slightly lifting each side alternately
until the cover is free.
Reverse this procedure to reinstall the cover.
Installing the DVI connector card
After following the instructions in “Internal access” to remove
the cover, do the following:
1. Remove and retain the two screws that hold the DVI
connector cover in place (figure 2), and set the cover aside.
You will not need it.
Figure 2 — Installing the DVI connector card
2. Insert the DVI connector through the hole that was created
in the rear panel in step 1.
3. Carefully align the DVI circuit card 50-pin connector with
socket J3 on the SGS 408 circuit board. With the pins
aligned, press down gently on the DVI circuit card. Check
the alignment of the DVI circuit card and socket J3.
Use the two previously removed DVI connector cover
screws to fasten the DVI connector in place.
4. Reinstall the cover of the SGS 408.
After removing the DVI connector cover,
insert the DVI connector through the
opening in the chassis and press
the circuit card evenly into the socket.
P
R
O
G
R
A
M
FREEZE BLACK
1
2
3
4
5
6 7 8
CUTTAK
E
PROGR
AM
PREVIEW
OUTPUT RATE
E
FF
E
C
T
TR
A
N
S
IT
IO
N
SGS 408
SEAMLESS GRAPHIC SWITCHER
INPUT
1
2
3
4
TRANSITIONS
EFFECTS
R
C
P
C
O
M
M
U
N
IC
A
T
IO
N
P
R
E
V
IE
W
FREEZE
BLACK
1
2
3 4 5
6
7
8
Tx
Rx
Remove #10 screw
(two plcs) each side
of front plate.
Lift cover
straight up
Remove (16)
screws from
top and sides.
  • Page 1 1
  • Page 2 2

Extron SGS 408 User manual

Extron
Brand
Extron
Model
SGS 408
Type
User manual

Extron SGS 408 is a professional-grade DVI connector that allows for the transmission of digital video signals over long distances. It is compatible with Extron DVI transmitters and receivers, and can be used to extend the reach of DVI signals up to 300 feet (91.44 meters) using standard CAT5e/6 cable. The SGS 408 supports resolutions up to 1920x1200, and is perfect for use in a variety of applications, including home theater, conference rooms, and classrooms. With its compact size and easy installation, the SGS 408 is a great way to add flexibility and convenience to your DVI system.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents