RKI Instruments GX-2009 User manual

RKI Instruments
Brand
RKI Instruments
Model
GX-2009
Type
User manual

This manual is also suitable for

RKI Instruments SDM-2009 is an advanced calibration station for the GX-2009 gas monitor. It allows you to perform bump tests and calibrations on your GX-2009 gas monitor quickly and easily. The SDM-2009U also features data transfer capabilities, allowing you to transfer calibration data to a USB flash drive or PC. With its user-friendly interface and compact design, the SDM-2009U is the perfect tool for keeping your GX-2009 gas monitor in top condition.

RKI Instruments SDM-2009 is an advanced calibration station for the GX-2009 gas monitor. It allows you to perform bump tests and calibrations on your GX-2009 gas monitor quickly and easily. The SDM-2009U also features data transfer capabilities, allowing you to transfer calibration data to a USB flash drive or PC. With its user-friendly interface and compact design, the SDM-2009U is the perfect tool for keeping your GX-2009 gas monitor in top condition.

www.rkiinstruments.com
RKI Instruments, Inc. • 33248 Central Ave. Union City, CA 94587 • Phone (800) 754-5165 • (510) 441-5656 • Fax (510) 441-5650
Confirm CAL C--LIMIT
If the LCD display reads CAL C--LIMIT,
press the Power/Mode button on the gas
monitor to continue to TRANSMIT.
If CAL C--LIMIT is not displayed continue to
the next step.
Calibration Results
Once calibration is complete, the display either shows a “P” for pass or an “F” for fail for each
sensor. The display will alternate between the gas concentration and the letter “P” when the
monitor passes calibration. The “CAL” LED lights in green when calibration is passed. “CAL”
LED lights in red if there is a failure.
Instrument Connected
Once on, the display will show gas channels
and a transmit message. The gas monitor is
ready for a Bump Test or Calibration.
Bump Test
Press the “Bump” button to start bump test.
Note: Ensure calibration gas cylinder is connected
to a demand flow regulator and then to the back
of the cal station. Make sure calibration gas
concentrations match values shown on display.
Bump Gas Reading
During Bump test, the display
shows current gas reading.
Bump Results
The BUMP LED will stop blinking and be on
steadily green if the bump test passed or
steadily red if the bump test failed. Display
will show “P” for pass or “F” for fail for each
sensor. The display will alternate between
the gas concentration and the letter “P”
when the monitor passes bump test.
Return to Transmit Screen
Press the “EDIT/ENTER” button.
See step “E” below for turning off
instrument after completion of
bump test.
Calibrate
Press the “CAL” button to start calibration.
Note: Ensure calibration gas cylinder is connected
to a demand flow regulator and then to the back
of the cal station. Make sure calibration gas
concentrations match values shown on display.
Removing from SDM-2009U
After a successful bump test or calibration,
the GX-2009 will automatically turn off within
15 seconds. To turn off manually, press
the SDM-2009 “Edit Enter” and “Power”
buttons simultaneously.
Warning: Do not remove the GX-2009
before turning it off, and do not use the
GX-2009’s power button to power it down.
Turn Cal Station On
1. Press the “POWER” button on the cal
station.
2. Seat the GX-2009 into the cal station.
Then turn on the GX-2009 by pressing
the “POWER/MODE” button on the gas
monitor.
Calibration Gas Readings
During calibration, the display shows
current gas readings. Typical calibration
will take 3 minutes.
A
B C
B
D
C
A
E
BUMP TEST
CALIBRATION
DATA TRANSFER
TURN ON
C
A B
A
D
Data Transfer To USB Flash Drive
With USB flash drive installed and unit powered on,
press and release the COPY button. The COPY LED will
become solid red while the records in the calibration
station’s memory are copied to the flash drive. In
addition, the flash drive’s LED will begin to blink.
When the LED stops blinking, the copy operation is
complete. Remove the flash drive from the USB port.
Transfer data to PC with Calibration Station software,
following the instructions in the Operator’s Manual.
GX-2009 Calibration Station
User Guide
Model SDM-2009U
PN 71-0264RK
  • Page 1 1
  • Page 2 2

RKI Instruments GX-2009 User manual

RKI Instruments
Brand
RKI Instruments
Model
GX-2009
Type
User manual
This manual is also suitable for

RKI Instruments SDM-2009 is an advanced calibration station for the GX-2009 gas monitor. It allows you to perform bump tests and calibrations on your GX-2009 gas monitor quickly and easily. The SDM-2009U also features data transfer capabilities, allowing you to transfer calibration data to a USB flash drive or PC. With its user-friendly interface and compact design, the SDM-2009U is the perfect tool for keeping your GX-2009 gas monitor in top condition.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents