Dodge Chain Tensioner Frame Owner's manual
- Type
- Owner's manual
INSTRUCTION MANUAL
FOR
DODGE
®
CHAIN TENSIONER FRAME
The chain tensioner frame may be mounted on surfaces parallel to o
r
at 90º to the plane of the chain drive. Mounting is accomplished by
using two 5/16" dia. bolts, provided by the user. Parallel surface
mounting provides a full 4" of adjustment. Installation on a surface
90º to the chain drive, will limit adjustment to 2½" or 1½", depending
on which intermediate mounting hole is used.
Refer to the assembly drawing on the back side of this sheet. When using an idler sprocket with a 5/8" bore, press
the adapter into the bore of the sprocket to allow proper assembly on the ½" bolt.
Up to a 1/2" of washers may be used between the mounting surface and the bracket for spacing purposes, if
necessary. Special adaptations must be made if the application requires greater spacing.
World Headquarters
P.O. Box 2400, Fort Smith, AR 72902-2400 U.S.A., Ph: (1) 479.646.4711, Fax (1) 479.648.5792, International Fax (1) 479.648.5895
Dodge Product Support
6040 Ponders Court, Greenville, SC 29615-4617 U.S.A., Ph: (1) 864.297.4800, Fax: (1) 864.281.2433
www.baldor.com
© Baldor Electric Company
All Rights Reserved. Printed in USA.
MN4043
(Replaces 499659)
06/30/09
*4043-0609*
Number of spacer washers
to be used between bracket
and bronze bushed Idler sprocket
Chain Pitch
Plain Washers
Lock Washers
Distance from
mounting surface to
centerline of sprocket
35, 40, 41, 2040 0 1 1
15
/
32
50, 2050 1 1 1
19
/
32
60, 60H, 2060 2 1 1
11
/
16
WARNING: Because of the possible danger to persons(s) or property from accidents which may result from the improper
use of products, it is important that correct procedures be followed. Products must be used in accordance with the
engineering information specified in the catalog. Proper installation, maintenance and operation procedures must be
observed. The instructions in the instruction manuals must be followed. Inspections should be made as necessary to
assure safe operation under prevailing conditions. Proper guards and other suitable safety devices or procedures as may
be desirable or as may be specified in safety codes should be provided, and are neither provided by Baldor Electric
Company nor are the responsibility of Baldor Electric Company. This unit and its associated equipment must be installed,
adjusted and maintained by qualified personnel who are familiar with the construction and operation of all equipment in the
system and the potential hazards involved. When risk to persons or property may be involved, a holding device must be an
integral part of the driven equipment beyond the speed reducer output shaft.
-
1
-
2
Dodge Chain Tensioner Frame Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Dodge Torque-Arm Speed Reducers Taper Bushed Metric HXT625, 725 Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Baldor-Reliance In-Line Helical Reducer Owner's manual
-
Baldor DODGE Torque-Arm TXT12 User manual
-
Baldor-Reliance RPM XE Integral Horsepower AC Motors Totally Enclosed Owner's manual
-
BIRO AFMG-52 Operating and Service Manual
-
Linear Garage Door Opener AUJ-S User manual
-
Baldor-Reliance RPM III DC Motor Frames DC180ATZ-C180ATZ & DC210ATZ Owner's manual
-
Audi AUD-S User manual
-
Baldor-Reliance RPM III DC Motor, Frames C210ATZ − C440ATZ, GK112 − GK280 Owner's manual
-
Baldor-Reliance Nuclear Service Class 1E Nuclear Service Non-Class 1E Integral and Fractional Horsepower AC Induction Motors TENV, TEFC Enclosures 48 – 449 Frame Owner's manual
-
Baldor-Reliance Integral Horsepower AC Induction Motors Owner's manual
