Renishaw PH10 Installation & User's Guide

Renishaw
Brand
Renishaw
Model
PH10
Type
Installation & User's Guide
PH10 PLUS installation and user's guide
Documentation part number: H-1000-7592-03-C
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
1
General information
© 2013 ‐ 2020 Renishaw plc. All rights reserved.
This document may not be copied or reproduced in whole or in part, or transferred to any other media or language, by any means, without
the prior written permission of Renishaw.
The publication of material within this document does not imply freedom from the patent rights of Renishaw plc.
Disclaimer
RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS DOCUMENT IS CORRECT AT THE DATE OF
PUBLICATION BUT MAKES NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT. RENISHAW EXCLUDES LIABILITY,
HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT.
Trademarks
RENISHAW, the probe symbol used in the RENISHAW logo and REVO are registered trademarks of Renishaw plc in the United Kingdom and
other countries. apply innovation and names and designations of other Renishaw products and technologies are trademarks of Renishaw
plc or its subsidiaries.
All brand names and product names used in this document are trade names, service marks, trademarks, or registered trademarks of their
respective owners.
All trademarks and trade names are acknowledged.
WEEE
The use of this symbol on Renishaw products and/or accompanying documentation indicates that the product should not be mixed with the
general household waste upon disposal. It is the responsibility of the end user to dispose of this product at a designated collection point for
waste electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of this product will help save valuable
resources and prevent potential negative effects on the environment. For more information, please contact your local waste disposal service
or Renishaw distributor.
Warranty
Renishaw plc warrants its equipment for a limited period (as set out in our Standard Terms and Conditions of Sale) provided that it is installed
exactly as defined in associated Renishaw documentation.
Prior consent must be obtained from Renishaw if non-Renishaw equipment (e.g. interfaces and/or cabling) is to be used or substituted. Failure
to comply with this will invalidate the Renishaw warranty.
Claims under warranty must be made from authorised service centres only, which may be advised by the supplier or distributor.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
2
Care of equipment
Renishaw probes and associated systems are precision tools used for obtaining precise measurements and must therefore be treated with
care.
Changes to Renishaw products
Renishaw reserves the right to improve, change or modify its hardware or software without incurring any obligations to make changes to
Renishaw equipment previously sold.
Packaging
To aid end user recycling and disposal the materials used in the different components of the packaging are stated here:
Packaging component Material 94/62/EC code 94/62/EC number
Outer box Polypropylene PP 5
Outer box Corrugated fibreboard PAP 20
Packing foam Low density Polyethylene LDPE 4
Packing foam Polyurethane PU 7
Bag Low density Polyethylene LDPE 4
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
3
Product compliance
EU declaration of conformity
Contact Renishaw plc or visit www.renishaw.com/EU for the full EU declaration.
EMC conformity
This equipment must be installed and used in accordance with this installation guide. This product is intended for industrial use only and
should not be used in a residential area or connected to a low voltage power supply network which supplies buildings used for residential
purposes.
FCC (USA only)
Information to user (47 CFR 15.105)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case you will be required to correct the interference at your own expense.
Information to user (47 CFR 15.21)
The user is cautioned that any changes or modifications not expressly approved by Renishaw plc or authorised representative could void the
user's authority to operate the equipment.
Equipment label (47 CFR 15.19)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
4
REACH regulation
Information required by Article 33﴾1﴿ of Regulation ﴾EC﴿ No. 1907/2006 ﴾“REACH”﴿ relating to products containing substances of very high
concern (SVHCs) is available at:
www.renishaw.com/REACH
China RoHS
Contact Renishaw plc or visit www.renishaw.com/ChinaRoHS for the full China RoHS tabulation.
TÜV
This equipment has been independently certified by TÜV SÜD America Inc in accordance with OSHA ﴾US﴿ and SCC ﴾Canada﴿ requirements to
the standards UL61010-1 Second Edition and CAN/CSA-C22-2 No. 61010-1 Second Edition.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
5
International safety instructions
BG ‐ ПРЕДУПРЕЖДЕНИЕ
Моля, обърнете на приложение 1 и прочетете инструкциите за безопасност на вашия собствен език, преди за разопаковате и
монтирате този продукт.
CZ ‐ VÝSTRAHA
Před rozbalením a instalací tohoto výrobku si přečtěte bezpečnostní pokyny ve vlastním jazyce uvedené v příloze 1.
DA - ADVARSEL
Læs sikkerhedsinstrukserne i Appendix 1 FØR udpakning og installation af dette produkt.
DE - WARNHINWEIS
Bevor Sie dieses Produkt auspacken und installieren, konsultieren Sie bitte Anhang 1 und lesen Sie die Sicherheitshinweise in Ihrer Sprache.
EL ‐ ΠΡΟΕΙΔΟΠΟΙΗΣΗ
Γυρίστε στο Κεφάλαιο 1 και διαβάστε τις οδηγίες ασφαλείας στη δική σας γλώσσα προτού ανοίξετε αυτό το προϊόν για να το
εγκαταστήσετε.
EN - WARNING
Before unpacking and installing this product, please consult Appendix 1 and read the safety instructions in your language.
ES - ADVERTENCIA
Consulte el apéndice 1 y lea las instrucciones de seguridad en su idioma antes de desempaquetar e instalar este producto.
ET - HOIATUS
Palun vaadake 1. lisa ning lugege enne selle toote lahtipakkimist ja paigaldamist ohutusjuhend läbi.
FI - VAROITUKSIA
Lue liitteessä 1 olevat omalla kielelläsi kirjoitetut turvaohjeet ennen tämän tuotteen pakkauksen avaamista ja asentamista.
FR - AVERTISSEMENT
Consulter l'annexe 1 et les instructions de sécurité dans votre propre langue avant de déballer et d'installer ce produit.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
6
GA - RABHADH
Téigh chuig aguisín 1 agus déan na treoracha sábháilteachta a léamh i do theanga féin le do thoil sula ndéantar an táirge seo a dhíphacáil
agus a shuiteáil.
HR - NAPOMENA
Prije nego što proizvod izvadite iz ambalaže i ugradite ga, otvorite Prilog 1 i pročitajte sigurnosne upute na svom jeziku.
HU – FIGYELMEZTETÉS
A termék kicsomagolása és telepítése előtt olvassa el az 1. számú függelékben található, az Ön anyanyelvén hozzáférhető biztonsági
utasításokat.
IT - AVVISO
Prima di aprire ed installare questo prodotto, leggere le istruzioni di sicurezza nella vostra lingua riportate nell'Appendice 1.
JA ‐ 警告
この製品を箱から取り出し設置する前に、付録 1 に記載された安全性に関する注意書きをお読みください。
LT – ĮSPĖJIMAS
Prieš išpakuodami ir įdiegdami produktą, turite grįžti prie 1 priedo ir perskaityti nurodymus dėl saugos savo kalba.
LV – BRĪDINĀJUMS
Pirms šī izstrādājuma izsaiņošanas un uzstādīšanas izskatiet 1. pielikumā sniegtās drošības instrukcijas savā valodā.
MT - TWISSIJA
Jekk jogħġbok mur f'appendiċi 1 u aqra l‐istruzzjonijiet tas‐sigurtà fil‐lingwa tiegħek qabel ma toħroġ dan il‐prodott mill‐ippakkjar u
tinstallah.
NL - WAARSCHUWING
Ga naar appendix 1 en lees de veiligheidsinstructies in uw eigen taal, voordat u dit product uitpakt en installeert.
PL ‐ OSTRZEŻENIE
Przed rozpakowaniem i zainstalowaniem tego produktu prosimy o zapoznanie się z Dodatkiem 1 i przeczytanie zaleceń dotyczących
bezpieczeństwa w danym języku.
PT ‐ ADVERTÊNCIA
Você deve retornar ao Anexo 1 e ler as instruções de segurança em seu idioma antes de desembalar e instalar este produto.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
7
RO - AVERTISMENT
Înainte de a desface ambalajul şi a instala acest produs, vă rugăm să căutaţi Anexa 1 şi să citiţi cu atenţie instrucţiunile de siguranță, în limba
română.
SK ‐ VÝSTRAHA
Pred rozbalením a inštaláciou tohto produktu si pozrite prílohu 1 a prečítajte si bezpečnostné pokyny vo vašom jazyku.
SL - OPOZORILO
Preden izdelek vzamete iz embalaže in ga vgradite, odprite Prilogo 1 in preberite varnostna navodila v svojem jeziku.
SV - VARNING
Gå till bilaga 1 och läs säkerhetsinstruktionerna på ditt eget språk innan du packar upp och installerar denna produkt.
TW ‐ 警告
在拆開和安裝本產品之前，請翻頁至附錄 1 閱讀母語的安全指示。
中文 — 警告
在拆包和安装本产品之前，请翻到附录1，阅读中文版安全说明。
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
8
Warnings
Where this symbol is displayed on the product the user must refer to the installation and user guide for information and safety advice.
Pinch hazards exist between moving parts and between moving and static parts. Do not hold the probe head during movements, or when
manually changing a probe.
Beware of unexpected movement. The user should remain outside the full working envelope of probe head/extension/probe combinations.
In all applications involving the use of machine tools or CMMs, eye protection is recommended.
Replace blown fuses with new components of the same type. Refer to the safety information in the relevant product documentation.
For instructions regarding the safe cleaning of Renishaw products, refer to the maintenance information in the relevant product
documentation.
Remove power before performing any maintenance operations.
Refer to the machine supplier's operating instructions.
It is the machine supplier's responsibility to ensure that the user is made aware of any hazards involved in operation, including those
mentioned in Renishaw product documentation, and to ensure that adequate guards and safety interlocks are provided.
Under certain circumstances the probe signal may falsely indicate a probe-seated condition. Do not rely on probe signals to stop machine
movement.
If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
The expected method of providing an emergency stop for Renishaw products is to remove power.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
9
References and associated documents
Title Document number
User's guide: Touch-trigger probes H-1000-5021
User's guide: SP25M H-1000-5104
User's guide: HCU2 H-1000-5631
User's guide: AM1 H-1000-4010
Data sheet: AM2 H-1000-2051
Technical specification: Styli and accessories H-1000-3200
Installation guide: PICS H-1000-5000
Installation and user's guide: PHC10-3 PLUS H-1000-0077
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
10
Introduction
This guide describes the installation and product usage of the PH10 PLUS series of motorised probe heads. This guide gives information on
physical installation and system connections, as well as assistance in fault-finding during the installation of a system.
The components of the PH10 PLUS system are not compatible with PH9 and PH20 system components. No attempt should be made to
connect the PH10 PLUS system components to a PH9 or PH20 system as this will result in damage to the product.
CAUTION: PH10 PLUS must be used in conjunction with the Renishaw PHC10-3 PLUS when part of an OEM installation not using
Renishaw UCC controllers.
This guide should be read in conjunction with the PHC10-3 PLUS installation guide (part number H-1000-0077) in order to fully understand
the system's features, capabilities and operation.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
11
PH10 system description
Product Description
PH10T PLUS A shank-mounted head with two-wired probe capability and an M8
thread.
PH10M PLUS A shank-mounted head with multiwired probe capability and a
Renishaw autojoint.
PH10MQ PLUS A quill-mounted head with multiwired probe capability and a
Renishaw autojoint.
HCU2 A hand control unit for use with PH10 measurement systems.
PHC10-3 PLUS A controller for use with PH10 measurement systems.
The PH10 PLUS range of motorised heads consists of three different models:
Each head in the PH10 PLUS range is a general purpose, versatile unit designed specifically for use on direct computer controlled (DCC)
CMMs and incorporates the following features:
720 indexing positions
0.4 μm indexing repeatability
7.5° indexing steps in both axes
300 mm (maximum) extension bar capability *
* NOTE: 450 mm is possible for PH10M PLUS / PH10MQ PLUS with special order carbon fibre extensions.
WARNING: The components of the PH10 PLUS system are not compatible with PH9 system components. No attempt should be
made to connect PH10 PLUS system components to a PH9 system, as this will result in damage to the product.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
12
System interconnection diagrams
PH10 PLUS system with standard two wired touch-trigger probes
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
13
PH10 PLUS system with standard two wire touch-trigger probe and autochange
Key Description
1 Communication connection to CMM controller RS232 or USB
3 Communication to CMM controller
4 Communication to autochange rack
5 PICS output to CMM
6 Probe output to CMM controller
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
14
PH10 PLUS system with standard two wire touch-trigger probe, PI 200-3 and
autochange
Key Description
1 Communication connection to CMM controller - RS232 or USB
3 Communication to CMM controller
4 Communication to autochange rack
5 PICS output to CMM controller
6 Raw probe output to CMM contoller
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
15
PH10 PLUS system with multiwire scanning probes
Key Description
1 Head cable(s)
2 RJ45 cable (supplied)
3 16 / 0.2 mm earth connection
4 MCU connection
5 Multiwire cable
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
16
Styli
Renishaw manufacture an extensive range of precision styli and stylus accessories. They are available in M2, M3, M4 and M5 thread sizes with
steel, tungsten carbide, graphite fibre and ceramic stems. Each is fitted with a precision industrial synthetic ball (ruby, zirconia or silicon
nitride) available in diameters from 0.3 mm (0.012 in) to 10 mm (0.4 in).
Special application styli including discs, cylinders, pointers, stars and large ceramic balls up to 30 mm (1.18 in) are available in M2 and M3
thread sizes.
For further information on the Renishaw stylus range, please refer to the stylus and accessories guide (part number H-1000-3200).
Renishaw also offer a custom design service if your requirements are not met by the standard range. Please contact your Renishaw supplier
for details.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
17
Probe extension bars
Renishaw manufactures a comprehensive range of extension bars and adaptors to allow increased component penetration.
There are three types in the range:
Autojoint to M8 bush (PAA series)
Autojoint to autojoint (PEM series)
M8 thread to M8 bush (PEL series)
Autojoint to M8 bush
These extension bars connect directly to the autojoint of the PH10M PLUS or PH10MQ PLUS head and terminate in an M8 bush. This permits
the use of two-wire touch-trigger probes.
Extensions Length Material Weight
PAA1 32 mm Steel 57 g
PAA2 144 mm Aluminium 85 g
PAA3 300 mm Aluminium 144 g
The probe is fitted to the extension by hand and tightened by use of the S1 ‘C' spanner as shown.
The S1 spanner is designed to fail before damage can occur to the mechanical joint between the two parts. Using the S1 spanner, fully hand-
tighten the probe body into the M8 bush (0.3 Nm to 0.5 Nm).
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
18
Autojoint to autojoint
These extension bars are compatible with the PH10M PLUS and PH10MQ PLUS heads. They allow direct connection to the head via the
autojoint and terminate in an autojoint. This permits use of a multiwired probe.
Extensions Length Material Weight
PEM25 25 mm Aluminium 60 g
PEM1 50 mm Aluminium 64 g
PEM2 100 mm Aluminium 93 g
PEM3 200 mm Aluminium 147 g
M8 thread to M8 bush
These extension bars can be used directly with the PH10T PLUS head, and also with the PH10M PLUS and PH10MQ PLUS heads using the
PAA1 adaptor.
Extensions Length Material Weight
PEL1 50 mm Aluminium 22 g
PEL2 100 mm Aluminium 43 g
PEL3 200 mm Aluminium 80 g
PEL4 300 mm Aluminium 141 g
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
19
PH10 compatible probes
M8 touch-trigger probes
This range of probes utilises the M8 bush for mounting to the head. These can be fitted directly onto the PH10T PLUS head, but when used
with the PH10M PLUS or PH10MQ PLUS heads, one of the autojoint to M8 bush extension bars of the PAA1 adaptor must be used.
Probe Diameter Application User's guide
TP2-5W 13 mm Universal probe for DCC and
manual CMMs.
H-1000-5021
TP6* 25 mm Universal probe for DCC and
manual CMMs.
H-1000-5008
TP20 13.2 mm Universal probe for DCC and
manual CMMs with module
changing.
H-1000-5021
TP200 13.5 mm Universal probe with strain
gauge for DCC CMM - 100 mm
max stylus length.
H-1000-5014
* An autojoint version (TP6A) is also available
Multiwire (autojoint) probes
This range of probes is compatible with the PH10M PLUS and PH10MQ PLUS heads only and utilise the Renishaw multiwired autojoint
connection to the head.
Probe Diameter Application Weight User's guide
SP25M 25 mm High speed scanning
probe.
65 g (body)
35 g (SM25-1)
40 g (SM25-2)
49 g (SM25-3)
71 g (SM25-4)
45 g (SM25-5)
40 g (TM25-20)
H-1000-5104
TP7M 25 mm Universal probe with
strain gauge for DCC
CMMs.
85 g (without stylus) H-1000-2010
SP600M* 50 mm Analogue contact
scanning probe.
216 g (without stylus) H-1000-5175
Probes in this range require comprehensive integration with your CMM.
* When using PH10MQ PLUS with SP600M, a PEM25 extension bar is required to achieve A = 97.5° or A = 105° in all B‐axis positions.
PH10 PLUS installation and user's guide
www.renishaw.com
Issued 03 2020
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65

Renishaw PH10 Installation & User's Guide

Renishaw
Brand
Renishaw
Model
PH10
Type
Installation & User's Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents