Eurotherm 5000 Owner's manual

5000 Series

100 and 180 mm video-graphics recorders

Data acquisition and logging units

Options Manual

E

UR

O

T

H

E

R

M

All rights are strictly reserved. No part of this document may be reproduced, modified, or transmitted

in any form by any means, nor may it be stored in a retrieval system other than for the purpose to act as

an aid in operating the equipment to which the document relates, without the prior written permission

of Eurotherm limited.

Eurotherm Limited pursues a policy of continuous development and product improvement. The speci-

fications in this document may therefore be changed without notice. The information in this document

is given in good faith, but is intended for guidance only. Eurotherm Limited will accept no responsibil-

ity for any losses arising from errors in this document.

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 1

GRAPHICS RECORDER / DATA ACQUISITION UNIT

OPTIONS MANUAL

ALPHABETIC LIST OF SECTIONS

Title Section Page

Effectivity

This manual refers to a number of different recorders and data acquisition units, not all of which support all the op-

tions described herein. If an option is not supported (or not fitted), it does not appear in the configuration menu.

Note that this manual deals with ‘stand alone’ options such as maths, totalisers etc. Those options which are exten-

sions of basic configuration, such as Circular Charts, Auditor Pack and Log Scales are described in the User Guide

supplied with the recorder.

For Remote Viewer and Communications option descriptions (including ASCII Printer Output), please refer to the

Serial Communications and Remote Viewer User guide: HA028122

For recorders which are being operated under Remote Viewer software, any mention, in this manual, of ‘Push’,

‘Touch’ or ‘Operate’ should be read ‘Click-on’.

The User Guide, or Installation and Operation Manual supplied with the unit specifies the Software Version to which

this (options) manual relates.

Batch Recording.................................................................................... Section 1 7

Counters............................................................................................... Section 5 77

Door Lock ........................................................................................... Section 12 105

E-Mail ............................................................................................... Section 11 101

Event Inputs .......................................................................................... Section 7 83

Maths ................................................................................................. Section 3 44

Portability options ............................................................................... Section 10 90

Screen builder (User screens).................................................................. Section 2 13

Timers ................................................................................................. Section 6 81

Totalisers .............................................................................................. Section 4 72

Transmitter power supply (isolated) ......................................................... Section 8 85

Transmitter power supply (non-isolated) ................................................... Section 9 88

User Screens (Screen Builder) ................................................................. Section 2 13

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 2

HA028121

Issue 5 Nov 04

GRAPHICS RECORDER

OPTIONS MANUAL

LIST OF CONTENTS

Section Page

1 BATCH RECORDING OPTION .............................................................. 7

1.1 INTRODUCTION.......................................................................................... 7

1.1.1 Auditor Pack messages......................................................................... 7

1.2 CONFIGURATION ....................................................................................... 8

SCOPE ............................................................................................... 8

ENABLE .............................................................................................. 8

BATCH MODE..................................................................................... 8

BATCH FIELDS ..................................................................................... 8

FIELD 1 ............................................................................................... 8

BATCH NUMBER ................................................................................. 9

FIELDS 2 TO 6..................................................................................... 9

ON START LOG................................................................................... 9

ON STOP LOG.................................................................................... 9

ON NEW CLEAR................................................................................. 9

NAME FILES BY BATCH........................................................................ 9

1.3 OPERATION ................................................................................................ 10

1.3.1 Operator initiation .............................................................................. 10

BATCH MESSAGE DISPLAY................................................................... 11

1.3.2 Non-operator initiation ......................................................................... 12

JOB INITIATION .................................................................................. 12

COUNTER INITIATION......................................................................... 12

MODBUS INITIATION .......................................................................... 12

1.3.3 Event sources........................................................................................ 12

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 3

LIST OF CONTENTS (Cont.)

Section Page

2 SCREEN BUILDER................................................................................ 13

2.1 INTRODUCTION.......................................................................................... 13

2.1.1 Versions ............................................................................................... 13

FULL ................................................................................................... 13

LITE .................................................................................................... 13

2.1.2 Display Access .................................................................................... 14

2.1.3 Importing/Exporting screens ................................................................. 14

IMPORTING SCREENS ......................................................................... 15

EXPORTING SCREENS ......................................................................... 15

2.2 DISPLAY CREATION ..................................................................................... 15

2.2.1 Before starting ..................................................................................... 15

2.2.2 Screen components .............................................................................. 16

2.2.3 Example.............................................................................................. 17

ACCESS TO THE PROPERTIES PAGE...................................................... 17

OPTIONS PAGE ITEMS ........................................................................ 18

PROCEDURE ....................................................................................... 19

2.3 PARAMETER DEFINITIONS............................................................................ 23

2.3.1 Basic parameters ................................................................................. 23

2.3.2 Advanced parameters .......................................................................... 25

2.4 COMPONENT DEFINITIONS ........................................................................ 31

2.4.1 Group Vertical/Horizontal Trend ........................................................... 31

2.4.2 Group vertical bargraph....................................................................... 31

2.4.3 Group horizontal bargraph................................................................... 31

2.4.4 Group numeric display ......................................................................... 32

2.4.5 Channel vertical/horizontal bargraph.................................................... 32

2.4.6 Channel Numeric................................................................................. 32

2.4.7 Channel data ...................................................................................... 32

2.4.8 Dialogue Action................................................................................... 32

2.4.9 Navigation Action................................................................................ 32

2.4.10 Operator button................................................................................. 33

2.4.11 Event Button ...................................................................................... 33

2.4.12 Image ............................................................................................... 33

2.4.13 Text .................................................................................................. 34

2.4.14 Round rectangle................................................................................. 34

2.4.15 Rectangle .......................................................................................... 34

2.4.16 Polyline - series of points..................................................................... 35

2.4.17 Polygon - closed area......................................................................... 36

2.4.18 Oval................................................................................................. 37

2.4.19 Line ................................................................................................... 37

Example.............................................................................................. 37

2.4.20 Arc................................................................................................... 38

Example.............................................................................................. 38

2.5 USER SCREENS WITH REMOTE VIEWER........................................................ 39

2.5.1 Quick Build Features ............................................................................ 40

TOP OF SCREEN ................................................................................. 41

BOTTOM OF SCREEN - PRIMARY SET ................................................... 41

BOTTOM OF SCREEN - SECONDARY SET............................................. 41

2.5.2 User Screens options page.................................................................... 42

OPTIONS PAGE ITEMS ........................................................................ 42

2.6 MEASURING UNIT COMPARISONS .............................................................. 43

2.6.1 VGA screen......................................................................................... 43

2.6.2 1/4VGA screen................................................................................... 43

2.7 ERROR CODES ............................................................................................ 43

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 4

HA028121

Issue 5 Nov 04

LIST OF CONTENTS (Cont.)

Section Page

3 MATHS .............................................................................................. 44

3.1 CONFIGURATION ....................................................................................... 44

3.1.1 Maths number ..................................................................................... 44

3.1.2 Value .................................................................................................. 44

3.1.3 Reset Now .......................................................................................... 44

3.1.4 Function .............................................................................................. 45

3.1.5 Scale Low / Scale High........................................................................ 48

3.1.6 PV Format ........................................................................................... 48

3.1.7 Remaining configuration items............................................................... 48

3.2 FUNCTION DETAILS..................................................................................... 48

3.2.1 Polynomial fit....................................................................................... 48

3.2.2 Fvalue................................................................................................. 49

Application Note ................................................................................. 49

3.2.3 Linear Mass flow.................................................................................. 50

SCALING FACTOR............................................................................... 50

SPECIFIC GAS CONSTANT .................................................................. 50

COMPRESSIBILITY FACTOR (Z-FACTOR) ................................................. 51

CONFIGURABLE PARAMETERS ............................................................. 51

3.2.4 Root Mass flow .................................................................................... 52

SCALING FACTOR............................................................................... 52

SPECIFIC GAS CONSTANT .................................................................. 52

COMPRESSIBILITY FACTOR (Z-FACTOR) ................................................. 52

CONFIGURABLE PARAMETERS ............................................................. 53

3.2.5 Rolling Average ................................................................................... 54

3.2.6 Mean Kinetic Temperature (MKT) ........................................................... 54

CONFIGURABLE ITEMS........................................................................ 55

3.2.7 Saturated Steam Mass Flow .................................................................. 56

PARAMETERS ...................................................................................... 56

PRESSURE UNITS CONVERSION .......................................................... 57

3.2.8 Saturated Steam Heat Flow ................................................................... 58

PARAMETERS ...................................................................................... 58

3.2.9 Saturated Steam Heat Consumed .......................................................... 59

PARAMETERS ...................................................................................... 60

3.2.10 Group MKT ....................................................................................... 60

3.2.11 Rate-of-change .................................................................................... 61

3.2.12 Oxygen (O2) correction ..................................................................... 62

APPLICATION NOTE ............................................................................ 62

3.2.13 Relative Humidity ................................................................................ 63

3.2.14 Zirconia probe .................................................................................. 64

OXYGEN CONCENTRATION ............................................................... 64

OXYGEN POTENTIAL .......................................................................... 66

3.2.15 Group Minimum ................................................................................ 68

DESCRIPTORS ..................................................................................... 68

3.3 MODBUS ADDRESSING............................................................................... 69

3.3.1 Maths channel configuration data.......................................................... 69

3.3.2 Maths Channel Run-Time data ............................................................... 70

3.3.3 IEEE 32-bit channel configuration data................................................... 70

3.3.4 IEEE Area Maths Channel run-time data ................................................. 71

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 5

4 TOTALISER OPTION............................................................................ 72

4.1 INTRODUCTION.......................................................................................... 72

4.2 CONFIGURATION ....................................................................................... 72

4.3 TOTALISER MODBUS ADDRESSING .............................................................. 74

4.3.1 Totaliser configuration data................................................................... 74

4.3.2 Run-Time data...................................................................................... 75

4.3.3 IEEE 32-bit configuration data ............................................................... 75

4.3.4 IEEE Area Totaliser run-time data ........................................................... 76

5 COUNTER OPTION ............................................................................. 77

5.1 INTRODUCTION.......................................................................................... 77

5.2 CONFIGURATION ....................................................................................... 77

5.2.1 Configurable parameters ...................................................................... 77

5.3 COUNTER MODBUS ADDRESSING............................................................... 78

5.3.1 Counter configuration data ................................................................... 78

5.3.2 Run-Time data...................................................................................... 79

5.3.3 IEEE 32-bit configuration data ............................................................... 79

5.3.4 IEEE Area Counter run-time data............................................................ 80

6 TIMERS OPTION................................................................................. 81

6.1 INTRODUCTION.......................................................................................... 81

6.2 CONFIGURATION ....................................................................................... 81

6.2.1 Configurable parameters ...................................................................... 82

SELF-START EXAMPLE ........................................................................... 82

7 EVENT INPUTS ................................................................................... 83

7.1 INTRODUCTION.......................................................................................... 83

7.2 SIGNAL WIRING TERMINATION .................................................................. 83

7.3 INPUT WIRING............................................................................................ 84

7.4 SPECIFICATION ........................................................................................... 84

8 ISOLATED TRANSMITTER POWER SUPPLY (TRS) OPTION...................... 85

8.1 INTRODUCTION.......................................................................................... 85

8.2 FUSING ...................................................................................................... 85

8.2.1 Fuse Rating ......................................................................................... 85

8.2.2 Access to the user connections/fuse ....................................................... 86

8.2.3 User wiring ......................................................................................... 87

9 NON-ISOLATED TRANSMITTER POWER SUPPLY (TRS) OPTION............. 88

9.1 INTRODUCTION.......................................................................................... 88

9. 2 PINOUT ..................................................................................................... 88

9.3 WIRING...................................................................................................... 89

LIST OF CONTENTS (Cont.)

Section Page

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 6

HA028121

Issue 5 Nov 04

10 PORTABLE CASE OPTIONS................................................................. 90

10.1 BASIC OPTION ......................................................................................... 91

10.1.1 Introduction ....................................................................................... 91

10.1.2 Wiring.............................................................................................. 91

SUPPLY VOLTAGE................................................................................. 91

SIGNAL WIRING................................................................................. 91

INTERNAL WIRING ............................................................................. 91

10.2 TRANSMITTER POWER SUPPLY (TRS) OPTION.............................................. 93

10.2.1 Internal wiring ................................................................................... 93

10.3 HTM2010 QUARTERLY TEST KIT.................................................................. 95

10.3.1 Introduction ....................................................................................... 95

10.3.2 Wiring.............................................................................................. 95

SUPPLY VOLTAGE................................................................................. 95

SIGNAL WIRING................................................................................. 95

10.3.3 Specification ..................................................................................... 96

INTERNAL WIRING ............................................................................. 96

10.4 THERMOCOUPLE OPTION ......................................................................... 97

10.4.1 Introduction ....................................................................................... 97

10.4.2 Wiring.............................................................................................. 97

SUPPLY VOLTAGE................................................................................. 97

SIGNAL WIRING................................................................................. 97

THERMOCOUPLE WIRING ................................................................... 98

10.4.3 Specification ..................................................................................... 99

10.5 LOW SUPPLY VOLTAGE OPTION................................................................. 100

11 EMAIL ............................................................................................. 101

11.1 E-MAIL CONFIGURATION .......................................................................... 101

11.1.1 Configurable parameters .................................................................... 102

11.2 E-MAIL DETAILS.......................................................................................... 103

11.2.1 The header area ................................................................................ 103

11.2.2 The body area................................................................................... 104

11.3 OPERATION .............................................................................................. 104

12 Door Lock option............................................................................. 105

Index .................................................................................................... 107

LIST OF CONTENTS (Cont.)

Section Page

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 7

1 BATCH RECORDING OPTION

Note: This option is not available with all models.

1.1 INTRODUCTION

Batch records form a part of recording history and are included in the normal archiving process to ‘disk’ or to a re-

mote PC (section 4.1 of the User Guide supplied with the unit). Batches can be initiated directly by the operator (if

access permission is granted), automatically whenever a specified counter changes value, by job or remotely via

MODBUS/TCP.

Batches can be defined as start/stop, or continuous and can incorporate all channels, or just those associated with a

Group. For start/stop batches, the batch record starts when the batch is started, and continues until it is stopped. For

continuous batches, the batch record starts when the batch is started and continues until the next batch is started, or

until batch recording is disabled.

When using 'PC review' software the 'Go to Batch' feature can be used to select a particular batch record.

If ' Name files by Batch' is enabled (section 1.2.8), a separate history file is created for each batch.

For each batch start, a start message is printed:

DD/MM/YY HH:MM:SS Batch start (User Full Name)

Where DD/MM/YY is the date, HH:MM:SS is the time, and User Full name is either the current user name or security

level (e.g. Engineer). A similar message is printed at Batch Stop. (There are no stop messages associated with con-

tinuous batch selection).

In addition to the above start/stop messages, up to six lines of text can, if required, be printed on the ‘chart’ at the start

of a batch and, if required, at the end of a batch. The messages are in two parts, which for the sake of this document,

are called ‘Headings’ and ‘Values’ The Headings are entered in Fields 1 to 6 in Batch Configuration (section 1.2).

The Values associated with these headings are entered by the operator at initiation (section 1.3).

1.1.1 Auditor Pack messages

If the Auditor Pack option is fitted a Config/Security Revision message appears immediately after the Batch Start

message:

DD/MM/YY HH:MM:SS Config Revision:NNNNNN Security Revision:SSSSSS

DD/MM/YY HH:MM:SS Batch start (User Full Name)

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 8

HA028121

Issue 5 Nov 04

1.2 CONFIGURATION

Figure 1.2 Batch configuration menu

As depicted in figure 1.2, the following configuration entries can be made:

SCOPE

Allows the user to define all configured channels (instrument) or just those in a particular group, for batch control. If

'Group' is selected, a further picklist appears allowing a specific group to be selected. If multiple groups are not

available, this list contains only group 1.

ENABLE

Allows the batch function to be switched on or off.

BATCH MODE

Allows batch mode to be selected as Continuous or Start/Stop.

BATCH FIELDS

Allows the maximum number of messages to be printed at batch start/stop to be selected between one and six.

FIELD 1

This field is the first of up to six which can be used as headings for batch information. Headings can be up to 20 char-

acters long (including spaces). In the example shown in Figure 1.2, Heading 1 has been entered as ‘Batch Number:’.

When initiating the batch, the operator has to enter a value to be associated with this heading (see section 1.3 Opera-

tion, below), unless 'Use Counter' is selected in the following 'Batch Number' field.

Enable

Batch mode

Batch Fields

Field 1

On start log

4

On stop log

On new clear

1

Name files by batch

Start/Stop

4

Batch Number:

Apply Discard

Field 2

Customer Name:

Field 3

Operator Name:

Field 4

Supervisor:

Archive

System

Save/Restore

Config

Security

Network

Group

Scope

Group

1) Group 1

Select

Instrument

or Group

Select

Start/Stop

or Continuous

Instrument

Groups

Channels

Views

Archive

Events

Event Buttons

Messages

User Linearisations

Batch

Maths

Totalisers

Counters

Timers

Serial Comms

Master Comms

Output Cha

Batch number: Use Counter

Counter Counter 1

Select

Counter or Text

Select Counter

(Appears only if 'Use

Counter' selected)

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 9

1.2 BATCH CONFIGURATION (Cont.)

BATCH NUMBER

This allows the Value entered for Field 1's heading to be selected as 'Use Text' or 'Use Counter'.

USE TEXT. When Text is selected, the value for field 1 is entered by the operator on initiation of the batch.

USE COUNTER. When Counter is selected, a further field appears ('counter') allowing a specific counter to be se-

lected from a picklist. The selected counter initiates a new batch whenever it changes value, and the counter value is

appended to the text associated with Field 1.

FIELDS 2 TO 6

Fields 2 to 6 are also used as headings for batch information. Values for these headings must be entered by the opera-

tor prior to Batch initiation. See also ‘On new clear’, below. Headings can be up to 20 characters long (including

spaces).

ON START LOG

This defines how many of the selected Fields are to be printed at batch start. An entry of ‘1’ means that only Field 1

will be printed. An entry of ‘2’ means that Fields 1 and 2 will be used, and so on. An entry of 0 means that only the

‘Batch Start’ message (section 1.1 above) will be printed. It is not possible to print only, say, Field 3. If Field 3 is

required, it must be preceded by Fields 1 and 2.

ON STOP LOG

As for On start log, above, but for batch stop. This item appears only if Start/Stop is selected as batch mode.

ON NEW CLEAR

For 'Use Text' Batches only, this allows the user to clear none or more of the batch entries at each batch start. In the

example above, if the user enters a batch number of say 001130.001, with Customer Name: FishesRus, Operator

name: Marvin, Supervisor: Fred, then setting ‘On New Clear’ to ‘1’, causes the batch number to be cleared, and to

have to be re-entered, each time a new batch is started.

In a similar way, setting ‘On New Clear’ to ‘2’ means that the batch number value and the Customer Name: value to

be cleared. A new batch cannot be started without new values first being entered.

NAME FILES BY BATCH

As an aid to identification, if ‘Name Files by Batch’ is selected, the Batch Name, as entered by the operator (section

1.3.1), is inserted into the history file name.

For example, if a batch name of 001130.001 is amongst the items archived to disk, then this file will appear in the

form:

Group Name~001130.001~HHHHHHHHHHHHHHHH,

Where HH----HH is a 16 digit hex code* used by the recorder and by review software to identify the file. If name

files by batch is not selected, the Batch name is not included, and the file will appear as:

Group Name~HHHHHHHHHHHHHHHH,

*The HHH--HHH code contains the following information:

HHHHHHHHHHHHHHHH

Lowest 3 bytes of the

instrument MAC address

History file format

version identifier

Group number

Group 1 = 00, Group 2 = 01 etc.

Sequential number (May skip one if there

is a configuration change)

622 6

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 10

HA028121

Issue 5 Nov 04

1.3 OPERATION

1.3.1 Operator initiation

This section describes how the operator initiates a new batch. Batches can be initiated from any of the trend, bar-

graph or numeric display modes, but the start/stop and other messages appear only on the Trend Graph screen, and its

associated trend history display. Batch information and status are retained whilst power is off.

To initiate a batch, either

Figure 1.3.1a Batch values entry page

Enter History

Channel Cycling Off

Faceplates On/Off

Batch

Note

Option Menu

Group 1Group

New Close

No batch in progressStatus

'Group' data appears only if

Scope = Group (Section 1.2)

Batch Number:

Customer Name:

Operator name:

Supervisor:

001130.001

FishesRus

Marvin

Fred

Batch

Start

CloseStore

a) Operate the Option key, then press ‘Batch’ in the Option

menu* which appears, or

b) Touch the (dark green) message area at the top of the screen.

*Note: The option menu is context sensitive, so its appearance may

differ from the example shown

The batch Status page appears - in this example - with no batch

running.

Press new.

A new display page appears (figure 1.3.1a), showing all the head-

ings entered in Field 1 to Field 6 during configuration. If the

Batch Fields entry (Section 1.2.3) is less than 6, then only the

selected number appear (in our example, 4).

‘Values’ can now be entered for these headings by entering strings of up to 60 characters (including spaces). This is

done, as usual, by touching the empty field and using the resulting pop-up keyboard to type-in the entry. Once the

entries are complete, operation of the Start button initiates batch recording. Operation of the Store button saves the

configuration for later initiation by counter or via MODBUS/TCP, if either option is fitted.

The Values entry page is replaced by the batch status page (figure 1.3.1b), this time showing details of the batch in

progress. This page allows the batch to be stopped or a new one triggered.

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 11

1.3.1 BATCH INITIATION (Cont.)

Figure 1.3.1b Status page (Batch running)

BATCH MESSAGE DISPLAY

The messages are displayed on the Graph Trend display as shown in figure 1.3.1c, below. This figure uses the exam-

ple given in the previous sections, and uses only four messages. Further messages would appear above message 4.

The figure also shows that time and date are added to the messages, and that the currently running batch number is

given in the Group name area. Touching this area calls the Batch status page.

Figure 1.3.1c Typical Batch start messages

Note: for Modbus initiated

messages, the Operator name

or login level ('Engineer' in

this example) is replaced by

'Modbus'.

Batch

Stop

Close

New

Batch in progressStatus

Batch Number: 001130.001

Customer Name: FishesRus

Operator Name: Marvin

Supervisor: Fred

Channel 1

400.00

800.00

700.87

Group 1

Batch Number 001130.001

14:25:59

30/11/00

14:24:33

30/11/00

14:21:51

30/11/00

14:19:11

30/11/00

Engineer

720.00640.00

30/11/00 14:25:28 Supervisor: Fred

30/11/00 14:25:28 Operator Name: Marvin

30/11/00 14:25:28 Customer name: FishesRus

30/11/00 14:25:28 Batch number: 001130.001

30/11/00 14:25:28 Batch start (Engineer)

Batch start message

Operator entries

480.00 560.00

Touching this area calls the

batch status page

Date and time auto-

matically printed

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 12

HA028121

Issue 5 Nov 04

1.3.2 Non-operator initiation

Batch start/stop can be initiated by job, by counter or via MODBUS/TCP

JOB INITIATION

As described in section 4.7.9 of the User Guide supplied with the unit, a job can be set up to initiate a batch whenever

the job source becomes active. If 'Scope' is set to 'Group' a specific group can be selected (default = Group 1) and the

job will act only on the batch associated with this group.

COUNTER INITIATION

If Batch Number is selected as 'Use Counter', (section 1.2) then a new batch will automatically be started whenever

the selected counter changes value (increment, decrement or preset). The new value of the counter is used as the

value associated with Field 1.

For the other fields to have values printed on the chart, these must have been entered as described above for Operator

initiation, then the 'Store' button touched.

The 'On new clear' setting (section 1.2) is ignored, the stored values being used each new batch.

Batch recording cannot be stopped by Counter action.

MODBUS INITIATION

In order to initiate batch recording via MODBUS/TCP, a Batch Start flag has to be set (value = 0001). For Scope =

Group (section 1.2), the flag for the specified group must be set. For Scope = Instrument any group's Batch Start flag

may be used.

The address of the flag for group 1 is decimal 42364; the address for group N is {42364 + 629(N-1)}

For further details of the Modbus option see section 2 of the Communications Manual.

If Batch mode = Start/Stop (section 1.2), batches can also be stopped via MODBUS. The address for group 1 is

42365; the address for group N is {42364 + 629(N-1)}. Again the value must be set to 0001.

Modbus start messages are of the form:

DD/MM/YY HH:MM:SS Batch start (Modbus)

Stop messages are similar.

1.3.3 Event sources

As described in section 4.3.6 of the User Guide (Event Configuration), ‘Batch Start’, ‘Batch Running’ and ‘Batch

Stop’ can be selected as event sources. If 'Scope' = 'Group' in Batch configuration (described above), then the user

can select which group's batch is to be used as the event source.

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 13

2 SCREEN BUILDER

Note: This option is not available with all models.

2.1 INTRODUCTION

This option allows the user to create screen layouts using recorder data, simple drawing tools, text and/or imported

image files. The option comes in two variants, known as ‘Lite’ and ‘Full’.

2.1.1 Versions

FULL

The Full version offers 24 user screens editable from the operator interface plus up to 100 extra screens which can

be created only at the remote viewer. Once created, such screens (25 to 124) can be copied or moved to one or

more of screens 1 to 24, thus becoming accessible at the instrument’s operator interface. (For the data acquisition

and logging unit, which has no operator interface other than Remote Viewer, there is no distinction between screens

1 to 24 and screens 25 to 124.)

When creating any of the screens at the remote viewer, a number of extra features are available to speed up the

screen creation process. These ‘Quick-build’ features include the ability to edit the position and size of a screen

component using familiar ‘click and drag’ mouse techniques, and the ability to ‘clone’ components. See section

2.5.1 for details.

LITE

The lite version is identical with the full version with the following exceptions:

1. There are only 6 user screens, all accessible from the user interface (if fitted).

2. The remote viewer does not include the ‘Quick-build’ features.

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 14

HA028121

Issue 5 Nov 04

Home Time-out

Home Group

Dark Trend Background

Dark History Background

Scope

Group

Display Enable

Home Page

Vertical Trend

Horizontal Trend

Vertical Bargraph

Horizontal Bargraph

Numeric Page

User Screen 1

User Screen 2

User Screen 3

User Screen 4

1) Group 1

Apply Discard

0

Group

1) Group 1

User Screen 1

User Screen 23

User Screen 24

Remote View User Screens

100

Archive

System

Save/Restore

Config

Security

Network

Instrument

Groups

Channels

Views

Archive

Events

Event Buttons

Messages

User Linearisations

Batch

Maths

Totalisers

Counters

Timers

Serial Com

Minutes

User Screens 1 to 6 appear only if the

User Screens 'Lite' option is fitted.

Remaining user screen fields appear

only if the User Screens 'Full' option is

fitted. See section 2 of the options

manual for User Screen details.

2.1.2 Display Access

As shown in figure 2.1, the user screens can be included in the display mode selection menus, described in section 3.4

of the User Guide supplied with the unit, and a User screen can be selected as the 'Home page'.

Note: Circular Trend option displays are not supported in User screens with this release of software.

Figure 2.1 .2 Views configuration menu

2.1.3 Importing/Exporting screens

The Save/Restore screen (figure 2.1.3) includes the categories 'Import screen' and ‘Export screen’.

Save

Restore

New

Text

Archive

System

Save/Restore

Config

Security

Network

Import Screen

Export Screen

File Name

User Screen

Import

See section 4.2 of the User

Guide for descriptions of

other Save/Restore func-

tions.

Import User Linearisation

Export User Linearisation

User Screen 1

screen

Import Printer Driver

Figure 2.1.3 Save/Restore menu (Import screen)

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 15

IMPORTING/EXPORTING SCREENS (Cont.)

IMPORTING SCREENS

Touching the filename area, allows a previously created user screen to be selected either from the Flash memory or

from disk to be imported. The User Screen picklist allows the user to define which User screen is to be 'replaced' by

the imported file.

EXPORTING SCREENS

Allows user screens to be exported to Flash memory, or disk, The operator can assign a suitable filename before

exporting.

2.2 DISPLAY CREATION

The following description is an attempt to show how to create a simple screen layout. The technique used is to define

an object, then to specify its size, and where its top left corner is to be located on the screen.

The option offers two levels of sophistication - basic and advanced. The basic system defines size, position, fill col-

our etc. for components (section 2.3.1). Advanced parameters allow a more sophisticated fine-tuning of the appear-

ance of the components

Note: X is horizontal, increasing rightwards. Y is vertical, increasing downwards.

As implied in figure 2.2.3a, screen component position and dimensions can be specified as percentage, absolute pixels

or relative pixels. Percentage is ‘percentage of screen size'. Absolute pixels allow position and/or dimensions to be

defined as an absolute number of pixels. Relative pixels are the same as absolute pixels, except that if the display is

rescaled on, say, a pc screen, the absolute pixel object will remain unchanged, whereas the relative pixel object will

scale appropriately. Similarly, for transfer from a VGA screen recorder to a 1/4VGA recorder or vice-versa.

2.2.1 Before starting

Before starting to lay the screen out:

1. The user must have ‘full configuration’ access permission.

2. One or more user screens must be enabled in Views Configuration (section 2.1)

3. A layout plan is produced, with all the required screen’s components listed with their top left corner co-ordinates,

their widths and heights, and where appropriate background and foreground colours.

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 16

HA028121

Issue 5 Nov 04

2.2.2 Screen components

Table 2.2.2 shows the selectable screen components, their default top-left corner positions, widths/heights and draw

order. All these components are described in section 2.4 below.

Table 2.2.2 User screen selectable item default values

Arc 0 0 10 10 10

Channel data 0 0 10 10 20

Channel horizontal bargraph 0 0 50 30 20

Channel numeric 0 0 50 20 20

Channel vertical bargraph 0 0 10 40 20

Dialogue action 0 0 10 10 10

Event Button 0 0 10 10 10

Group horizontal bargraph 0 0 50 50 30

Group horizontal trend 0 0 50 50 30

Group numeric 0 0 50 50 30

Group vertical bargraph 0 0 50 50 30

Group vertical trend 0 0 50 50 30

Image 0 0 10 10 10

Line 0 0 10 10 10

Main 0 0 100 100 1

Navigation action 0 0 10 10 10

Operator Button 0 0 10 10 10

Oval 0 0 10 10 10

Polygon 0 0 N/A N/A 10

Polyline 0 0 N/A N/A 10

Rectangle 0 0 10 10 10

Round rectangle 0 0 10 10 10

Text 0 0 0 0 20

Component

Draw

Order

X Y Width Height

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

HA028121

Issue 5 Nov 04

Options

Page 17

2.2.3 Example

To produce a new display screen with channels one to four inclusive each displayed as an independent bar graph

across the width of the screen, with Group 1 vertical trend display below. To achieve the above, the following items

will be required:

1. Bar1: Horizontal bargraph with X = 0, Y = 0, Width = 100, Height = 10, channel = Channel 1

2. Bar2: Horizontal bargraph with X = 0, Y = 12, Width = 100, Height = 10, channel = Channel 2

3. Bar3: Horizontal bargraph with X = 0, Y = 24, Width = 100, Height = 10, channel = Channel 3

4. Bar4: Horizontal bargraph with X = 0, Y = 36, Width = 100, Height = 10, channel = Channel 4

5. Group 1: Vertical trend group with X = 25, Y = 48, Width = 50, Height = 50. Group name to appear above display.

Figure 2.2.3a Component properties and

User screen options pages

ACCESS TO THE PROPERTIES PAGE

1. Ensure that one or more user screens is enabled in

views Configuration (section 2.1). If necessary, call

the required User screen to the display using the Root

menu 'Goto View' menu.

2. Press the Option key to call the Option Menu.

3. Press ‘Edit Screen’ to call the ‘Component Property

Editor’ page to the display. This display contains the

basic properties of the ‘Main’ (background) screen

onto which the required components are to be overlaid.

Note: This may take some seconds, according to the

complexity of the configuration

4. A further press of the Option key calls the user screen

Options display page.

For this example, only the basic attributes will be re-

quired, so the basic/advanced pick list can be ignored.

Component descriptions are not required for display,

so the Component info on screen check box can be left

un-selected.

The final check box (Quick entry to edit) can be se-

lected. When selected, the option key calls the compo-

nent properties page directly from the user screen,

without the option menu appearing.

5 Use the option key again to return to the Component

Properties display

Add

Del

main_1.2

Identifier main_1.2

Component Property Editor - Screen 1

Save Discard New Close

Component picklist field

Add/Delete component keys

Note

Batch

Option Menu

Edit Screen

Usr Screen Options

Edit level

Component info on screen

Quick entry to edit

Basic

Last Error

Page Title

X Position

Y Position

Width

Height

Draw Order

Component Type Main

-1

100

0

%

Dimension picklist.

Select %, absolute pixels,

or relative pixels.

Component properties

(Fields vary according to

component type)

Background Colour -1

GRAPHICS RECORDER/DATA ACQUISITION AND LOGGING UNIT: OPTIONS MANUAL

Options

Page 18

HA028121

Issue 5 Nov 04

2.2.3 SCREEN CREATION PROCESS (Cont.)

KEY DESCRIPTIONS

Add Calls the Component selection list

Del Deletes (after confirmation) the component in the Identifier field (except the Main pane which cannot be de-

leted).

Save Causes all changes made since the last ‘Save’ to be applied to the screen.

Discard Causes all changes made since the last ‘Save’ to be discarded, after confirmation.

New Removes (after confirmation) all components from the current list and generates a new, empty background

(main) page to be worked on. This change is permanent and cannot be 'Discarded'.

Close Closes the component properties page and displays the screen currently being edited. If this key is operated

whilst there are still unapplied changes, a confirmation pop-up appears (Save Discard, Cancel).

Note: When working on the full version from remote viewer, further keys appear (e.g. Goto Canvas). These

are fully explained in section 2.5.1.

OPTIONS PAGE ITEMS

Edit level

Allows Basic or Advanced edit level to be selected for further use.

Component info on screen

Enabling this box causes a component description to appear at the top left corner of each component. This de-

scription is in the form: Identifier(X,Y)+[∂X,∂Y], where X and Y defines the top left corner position in pixels,

and ∂X and ∂Y are the width and height of the component in pixels. The identifier is the component name as

appears in the Identifier field of the Component Property Editor page.

Quick entry to edit

If selected, this function allows direct entry from the user screen being edited to the Component Property editor

page, without the options menu first appearing offering the choice of ‘Batch’ or ‘Edit Screen’.

If Quick entry is selected, the option menu does not appear when the option key is touched. The Batch status

page can be called by touching the ‘Page Name’ (Dark Green) area at the top of the screen, as an alternative to the

option menu.

Quick entry has no effect on screens other than user screens.

Note: When working on the full version from remote viewer, further items appear (e.g. Use Last Properties).

These are fully explained in section 2.5.2.

Page is loading ...

Eurotherm 5000 Owner's manual

This manual is also suitable for

Eurotherm 5000 Owner's manual

Related papers

Other documents