Other 8033914 User manual

Issue 1 - 26/05/10

Please read these instructions fully before starting assembly

Assembly Instructions -

Please keep for future reference

Sliding Gazebo

803 3914

Important –

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800

Dimensions

Width - 300cm

Depth - 300cm

Height - 232cm

•Weight: kgs.

•

1

Safety and Care Advice

Important – Pl e a se read th e se instructions fully be fore starting asse mbly

• Check you have all the

components and tools listed on

pages 2 & 3.

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product during assembly,

this could cause damage.

• Assemble the item as close

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

arbour or your floor.

• Parts of the assembly will be

easier with 4 people.

•

We do not

recommend the

use of power

drill/drivers for

inserting screws ,

as this could damage the unit.

Only use hand screwdrivers.

• Dispose of all packaging

efully and responsibly.

Care and mainte nance

Please lift with care.

Warning:

Take care when

operating or moving the unit.

•Only clean using a damp cloth

and mild detergent, do not use

bleach or abrasive cleaners.

•Make sure each screw

matches the corresponding

figure to ensure correct

assembly.

•From time to time check that

there are no loose screws on

this arbour.

•This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

•To prolong the life of this

unit, we recommend it is stored

inside during winter or extended

periods of bad weather.

58

car

Components - Parts

Please check you have all the parts listed below

Sliding top tube on two sides x2

Front horizontal tube x1

Back horizontal tube x1

Top tube x2

Sliding top tube in the middle x1

Leg tube x4

Left hanging fabric tube x1

Right hanging fabric tube x1

Left fabric tube x5

Right fabric tube x5

2

1

2

3

4

5

6

7

8

9

10

Components - Parts

Please check you have all the parts listed below

Footstand x4

Protection cover x1

Roof Cover x1

Components - Fittings

Note:

The quantities

below are the correct amount to complete the assembly.

Ground pins x 16

15mm Screw x 14

Please check you have all the fittings listed below

l required

R uler - Use this ruler to help correctly identify the screws

62mm Screw x 22

Metal washer x 39

Plastic cap x 39

15mm Screw x 10

32mm Screw x 3

Plastic cap x 10

3

11

12

13

A

B

C

D

E

F

G H

I

13mm Screw x 14

K

J

L

M

Spanner x 1

Allen key x 2

Tube cap x 8

Tube cap x 6

Assembly Instructions

Step 1

Assembly frame

Step 2

Use 16 mm screw

and metal washer

to fix footstand

to leg tube

Suggest to complete this

product assembly by four

persons.

.

4

A

E

6

13

then seal it

cap .

H

with

plastic

Tighten the screw

,

A

13

6

3

5

3

A

6

H

E

5 3

&

Take the protective foams

away from two sides of

.

sliding top tube

Step 3

Step 4

use 13 mm screw to

fix it.

5

I

3

5

K

I

J

I

J

2

J

I

Assembly Instructions

5

1

J

2

Insert tube cap to the

5

&

K

sliding top tube

,

K

Insert tube cap to the

J

horizontal tube

1

,

use

13 mm screw to

I

fix it.

Step 5

Insert tube cap to the

J

horizontal tube

2

,

use

13 mm screw to

I

fix it.

1

Step 6

&

6

5

2

.

D

H

Tighten all the screw

and seal them with

plastic cap

4

J

4

I

2

1

3

4

5

2

1

3

4

5

&

3

4

5

&

E

H

D

H

E

D

Assembly Instructions

Insert tube cap to the

J

top tube

4

,

use

13 mm

I

to fix it.

Step 7

sliding top tube

on

Use 62mm screw

and

metal washer

to fix

D

E

top

tubes

4

3

horizontal

&

tube

1

.

screw

Step 6

.

E

7

Assembly Instructions

2

6

3

H

E

D

3

1

E

D

H

Use

62mm screw

and metal washer

to fix sliding top tube

on

Use

62mm screw

and metal washer

to fix horizontal

tube

&

on leg tube

.

D

E

D

E

1 2 6

3

then seal it

cap .

H

with

plastic

Tighten the screw

D

,

leg tube .

6

Assembly Instructions

Step 9

E

7

12

2

7

2

C

H

8

E

C

H

2

C

E

5

9

10

9

10

3

12

9

10

&

B

G

B

9

10

&

9

10

8

12

9

10

3

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

Figure 6

Figure 7

Figure 8

Figure 9

Figure 12

Figure 11

Figure 10

Use 32mm screw

and

metal washer

to fix

hanging fabric tube

&

to back horizontal tube

Use 15mm screw

to fix fabric tube

&

on sliding top tube on two

sides

, as Figure 11,

Connect fabric tube

&

through sliding top tube in

the middle

C

E

7 8

2

B

9 10

3

9

10

5

Tighten

all the screw

C

and seal them with

plastic

cap

H

.

Figure 4, Figure 5.

Figure 12.

.

B

G

Tighten all the screw

and seal them with

plastic cap

as

,

, as Figure 8

Figure 9 and

Connect

fabric tube

8

7

&

,

as Figure 3.

Put fabric tube

&

into roof cover

12

7

8

&

9 10

Figure 4, Figure 5,

as

Figure 6, Figure 7.

Figure 10.

9

Step 10

Use 15mm screw

and

metal washer

to fix

protection cover

on

sliding top tube

&

.

Tighten all the screw

and seal them

cap

.

A

E

11

3 5

A

with plastic

H

Assembly is complete.

Use ground pins

footstand

into ground

if you want to firm this arbou

r

.

to fix

F

13

Argos Limited

489-499 Avebury Boulevard Saxon Gate West Central Milton Keynes Bucks,MK9 2NW

If you need help or have damaged or missing p

For further assistance please visit http://www.argos-support.co.uk/

arts, call the

Customer Helpline: 03456 400800

11

H

A

E

11

13

F

Assembly Instructions

Other 8033914 User manual

This manual is also suitable for

Other 8033914 User manual

Other documents