Danfoss IHx Controller Operating instructions
- Type
- Operating instructions
Instructions
IHx control family PM2+P, PTC2+P, IHPT
73691900 DH-SMT/SI VI.LJ.A3.9P © Danfoss 04/2008 1
PM2+P PTC2+P, IHPT IDLE controller
ENGLISH
Integrated heat exchanger self-acting controller
IHx control family PM2+P, PTC2+P, IHPT
www.danfoss.com Page 5
DANSK
Integreret selvvirkende regulator til varmevekslere
IHx regulatorer PM2+P, PTC2+P, IHPT
www.danfoss.dk Side 5
DEUTSCH
Direkt am Wärmeübertrager angeschlossener selbsttätiger
Regler IHx Reglerserie PM2+P, PTC2+P, IHPT
www.danfoss.de Seite 6
NEDERLANDS
Geintegreerde automatische temperatuurregelaar voor warmte
wisselaars. IHx regelaar behoort tot de groep PM2+P, PTC2+P, IHPT
www.danfoss.nl Blz. 6
Page is loading ...
Page is loading ...
Page is loading ...
73691900 DH-SMT/SI VI.LJ.A3.9P © Danfoss 04/2008 5
DANSKENGLISH
Safety Notes
Prior to assembly and commissioning
to avoid injury of persons and damages
of the devices, it is absolutely necessary
to carefully read and observe these
instructions.
Necessary assembly, start-up, and
maintenance work must be performed
only by qualified, trained and authorized
personnel.
Prior to assembly and maintenance work
on the controller, the system must be:
- depressurized,
- cooled down,
- emptied and
- cleaned.
Please comply with the instructions of the
system manufacturer or system operator.
Definition of Application
1
IHx is an integrated self-acting family
of controllers developed for controlling
instantaneous heating of domestic hot
water with heat exchangers. The capacity
of controllers fully cover the needs of
domestic hot water for flats, one family
houses or dwellings and can be mounted
to district heating network directly, to a
block of heating systems or central located
boiler system in a dwelling house.
Assembly
Connecting of IDLE controller
(relevant only at PM2+P and PTC2+P
controllers)
At no load - application preheated to set
temperature
2
At no load - only supply lines pre-heated,
Heat exchanger kept cold
3
Idle controller
Mounting
4
Sensor mounting
5
(relevant only at PTC2+P and IHPT controllers)
Dimensions
7
Two different connections are possible:
A - Union nut
B - O-ring
Pressure test
The maximum test pressure is: 1.5 × PN
PN - see product label!
Temperature setting
6
DANSK
Sikkerhedsbestemmelser
Disse instruktioner SKAL læses
omhyggeligt forud for montering
og indkøring samt respekteres for at
undgå skader på personer og udstyr.
Nødvendigt monterings-, opstart- og
vedligeholdelsesarbejde må kun udføres af
faglært og autoriseret personale.
Forud for monterings- og
vedligeholdelsesarbejde på regulatoren
skal systemet være:
- trykløst,
- nedkølet,
- tømt og
- rengjort.
Systemproducentens eller -operatørens
instruktioner skal overholdes.
Anvendelse
1
IHx er en række af integrerede selvvirkende
regulatorer udviklet specielt til regulering
af brugsvand i varmevekslere.
Regulatorernes kapacitet dækker fuldt
ud kravet til brugsvand i lejligheder og
enfamilieshuse og kan monteres direkte i
ernvarmenettet eller i et centralt placeret
varmesystem.
Montering
Tilslutning af regulator
PM2+P, PTC2+P
I tomgang er anlægget opvarmet til
indstillet temperatur
2
I tomgang er kun forsyningsrør forvarmede,
varmeveksleren holdes kold
3
.
af regulator
Montering
4
Følermontering
5
PTC2+P, IHPT
Dimensioner
7
Trykprøvning
Det maksimale prøvetryk er: 1,5 × PN
PN fremgår af produktetiketten
Temperaturindstilling
6
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Danfoss IHx Controller Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- Deutsch: Danfoss IHx Controller Bedienungsanleitung
- Nederlands: Danfoss IHx Controller Handleiding
- dansk: Danfoss IHx Controller Betjeningsvejledning
Related papers
-
Danfoss IHx Controller Operating instructions
-
-
Danfoss IHx Controllers - PM2+P, PTC2+P, IHPT - PN16 Operating instructions
-
-
-
-
-
-
-