Sealey YKGS20 User manual

Type
User manual

Sealey YKGS20 is a safety guard for use with floor presses, designed to protect the user and bystanders from injury caused by dislodged workpieces. Its lightweight aluminum frame and tough steel mesh construction provide durability and protection. It features five height increments, allowing for easy workpiece placement and unobstructed operation. The one-way spring-loaded locking clips ensure quick and secure positioning of the guard. Installation involves fixing the guard support brackets to the press table using pre-drilled holes and provided fixings.

Sealey YKGS20 is a safety guard for use with floor presses, designed to protect the user and bystanders from injury caused by dislodged workpieces. Its lightweight aluminum frame and tough steel mesh construction provide durability and protection. It features five height increments, allowing for easy workpiece placement and unobstructed operation. The one-way spring-loaded locking clips ensure quick and secure positioning of the guard. Installation involves fixing the guard support brackets to the press table using pre-drilled holes and provided fixings.

SAFETY GUARD FOR PRESSES
MODEL NO’S: YKGS20, 30, 50, 75
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9 Regularlycheckguardforworn,loose,ordamagedparts.IfyoundanyoftheseconditionsDO NOT USE THE GUARD.
 Failuretodosomaycausesevereinjury!
9 Keeptheguardfreeofdirtanddebris.
8 DO NOTaddtoormodifyanypartoftheguard.Doingsowillvoidyourwarranty.
8 DO NOTusetheguardforpurposesotherthanthoseitwasdesignedfor.
9 Cleanguardwithwaterandmilddetergent.
9 Alwaysrefertothesafetyinstructionsprovidedinyouroorpressinstructionmanual.
WARNING! Thewarnings,cautionsandinstructionsreferredtointhismanualcannotcoverallpossibleconditionsandsituationsthat
 mayoccur.Itmustbeunderstoodthatcommonsenseandcautionarefactorswhichcannotbebuiltintothisproduct,butmustbe
 appliedbytheoperator.
2. INTRODUCTION
Lightweightaluminiumframewithtoughsteelmesh.Adjustableguardprotectstheuserand/orpasserbyfrombeinginjuredifworkpieceis
accidentlydislodgedunderload.Boltsontoeithersideofthetableandfeaturesveheightincrements,allowingtheworkpiecetobeplacedonto
tablewithnoobstruction.One-wayspringloadedlockingclipsthenallowtheguardtobepulledupquicklyandsnapstraightintopositionforfull
protection.
3. SPECIFICATION
Model No: ................................................................ YKSG20
Applications: ............................................ YK209F, YK20FFP
Model No: ................................................................ YKSG30
Applications: .............................YK30F, YK30FAH, YK30FFP
Model No: ................................................................ YKSG50
Applications: ......................... YK509F, YK509FAH, YK50FFP
Model No: ................................................................ YKGS75
Applications: .......................................... YK759F, YK759FAH
4. ASSEMBLY/ OPERATION
4.1.  Choosewhichsideoftheoorpresstottheguard,xtheguardsupportbracketstothe
 tableusingthepre-drilledholesandxingsprovided.Seegs.1&2.
 Ensurethebracketsarettedwiththelocksontheoutsideandthecorrectwayupasg.1.
Refer to
instruction
manual
YKSG20,30,50,75Issue:2(H,F)07/04/22
Original Language Version
©JackSealeyLimited
Guard Support Guard Support
BracketFixingsBracketFixings
Ensure The Correct Ensure The Correct
OrientationOfTheOrientationOfThe
LockingMechanismLockingMechanism
Rear Rear
ViewOfViewOf
BracketBracket
FixingsFixings
g.1
g.2
4.2.  Taketheguardandslideitintothebracketsfromabove;theguardhasastoponeithersideatthetopoftheframe,thisshouldbe
 uppermostandfacingtowardstheoperatorg.3.
4.3.  Pullthelocksbackoneithersideandlowertheguardallthewaydown.
CAUTION! Theguardwilldropfreelyuntilitreachesthestops.
4.4.  Toraisetheguardtooneoftheveheightincrements,pulluptheguardandthespringloadedlockingclipswillsnapintopositionat
 thedesiredheight.
.
Original Language Version
©JackSealeyLimited
Guard Stops
Uppermost
fig.3
YKSG20,30,50,75Issue:2(H,F)07/04/22
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycleunwantedmaterialsinsteadofdisposingofthemaswaste.Alltools,accessoriesandpackagingshouldbesorted,takento
arecyclingcentreanddisposedofinamannerwhichiscompatiblewiththeenvironment.Whentheproductbecomescompletely
unserviceableandrequiresdisposal,drainanyfluids(ifapplicable)intoapprovedcontainersanddisposeoftheproductandfluids
accordingtolocalregulations.
Note:Itisourpolicytocontinuallyimproveproductsandassuchwereservetherighttoalterdata,specificationsandcomponentpartswithoutprior
notice.
Important:NoLiabilityisacceptedforincorrectuseofthisproduct.
Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.
  • Page 1 1
  • Page 2 2

Sealey YKGS20 User manual

Type
User manual

Sealey YKGS20 is a safety guard for use with floor presses, designed to protect the user and bystanders from injury caused by dislodged workpieces. Its lightweight aluminum frame and tough steel mesh construction provide durability and protection. It features five height increments, allowing for easy workpiece placement and unobstructed operation. The one-way spring-loaded locking clips ensure quick and secure positioning of the guard. Installation involves fixing the guard support brackets to the press table using pre-drilled holes and provided fixings.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI