Indian Motorcycle 2889224 Saddlebag Light Kit is designed to enhance the visibility and safety of your motorcycle. With its easy installation process, you can quickly add bright LED lights to your saddlebags, improving your visibility to other road users and increasing your riding confidence. The kit includes all necessary hardware and detailed instructions to guide you through the installation process, ensuring a secure and proper fit.
Indian Motorcycle 2889224 Saddlebag Light Kit is designed to enhance the visibility and safety of your motorcycle. With its easy installation process, you can quickly add bright LED lights to your saddlebags, improving your visibility to other road users and increasing your riding confidence. The kit includes all necessary hardware and detailed instructions to guide you through the installation process, ensuring a secure and proper fit.
BBEEFFOORREE YYOOUU BBEEGGIINN
Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
AAPPPPLLIICCAATTIIOONN
Verify accessory fitment at www.indianmotorcycle.com.
KKIITT CCOONNTTEENNTTSS
REF QTY PART DESCRIPTION P/N AVAILABLE
SEPARATELY
1 1 Harness, Rear Lighting 2416016
2 1 Light, Saddlebag, Left 2416021
31Light, Saddlebag, Right 2416022
4 6 Routing Clip 5454593
5 4 Foam, 6.0 x 12 .7 x 50.8 mm (Removable) n/a
TTOOOOLLSS RREEQQUUIIRREEDD
• Socket Set, Hex Bit, Metric
• Socket Set, Torx®Bit
• Safety Glasses
• Torque Wrench
Instr 9939998 Rev 01 2021-09 Page 1 of 18
P/N 2889224
SSAADDDDLLEEBBAAGG LLIIGGHHTT KKIITT
Instr 9939998 Rev 01 2021-09 Page 2 of 18
CCOONNSSUUMMAABBLLEESS RREEQQUUIIRREEDD
• Isopropyl Alcohol (IPA)
IIMMPPOORRTTAANNTT
Your Indian Motorcycle®Saddlebag Light Kit is exclusively designed for your vehicle. Please read the
installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of
debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in
the sequence shown.
IINNSSTTAALLLLAATTIIOONN IINNSSTTRRUUCCTTIIOONNSS
For Indian Chieftain®/Roadmaster®, skip ahead to
page 10.
IINNDDIIAANN CCHHAALLLLEENNGGEERR
VVEEHHIICCLLEE PPRREEPPAARRAATTIIOONN
GGEENNEERRAALL
1. Park motorcycle on a flat surface, fully extend
kickstand, and make sure vehicle is stable.
2. Turn key or ignition switch to OFF position and
remove key. If equipped with keyless fob,
remove fob from proximity of vehicle.
RREEMMOOVVEE LLEEFFTT SSIIDDEE PPAANNEELL
1. Grasp front lower corner left side panel and
gently pull away from vehicle to release three
grommet pins. Use caution to prevent damage to
painted surfaces.
RREEMMOOVVEE SSEEAATT
1. Remove and keep one screw from each side of
seat.
2. Pull seat rearward, then upward to disengage
seat from frame mount and hat bushing. Do not
allow seat mount brackets to contact rear fender.
Instr 9939998 Rev 01 2021-09 Page 3 of 18
WWIIRREELLEESSSS CCOONNTTRROOLL MMOODDUULLEE AANNDD KKEEYY FFOOBB
AANNTTEENNNNAA RREEMMOOVVAALL
1. Pull the hose down and away from the key fob
antenna.
2. Disconnect key fob antenna connector.
3. Move the key fob antenna rearward to release
from bracket.
4. Tilt the key fob antenna up and remove.
5. Disconnect wireless control module connector.
6. Lift wireless control module. Move it down and
remove.
SSAADDDDLLEEBBAAGG RREEMMOOVVAALL
HARD SADDLEBAGS ONLY:
1. Unlock electric saddlebag lock (if equipped).
TIP
Provided key can also be used in latch release
buttons to unlock saddlebag lids.
Instr 9939998 Rev 01 2021-09 Page 4 of 18
2. Disconnect saddle bag lock wiring near seat.
3. Repeat this section for opposite side.
ALL SADDLEBAGS
1. Open saddlebag.
2. Remove and keep two screws A.
3. Tilt saddlebag away from frame and remove
from vehicle.
NOTE
Lift leather saddlebags up-and-off spools before
tilting off frame.
4. Repeat this section for opposite saddlebag.
AACCCCEESSSSOORRYY IINNSSTTAALLLLAATTIIOONN
NOTICE
Left side shown; right side similar.
HHAARRNNEESSSS IINNSSTTAALLLLAATTIIOONN
1. Route harness qunder bracket and through
both left and right hand frame.
Instr 9939998 Rev 01 2021-09 Page 5 of 18
RROOUUTTIINNGG CCLLIIPP IINNSSTTAALLLLAATTIIOONN
1. Clean the inboard side with 50:50 isopropyl
alcohol/water solution.
WARNING
Isopropyl alcohol is hazardous to your health. See
isopropyl alcohol packaging for proper handling
instructions, including recommended personal
protective equipment such as goggles and
chemical resistant gloves.
2. Remove adhesive backer from routing clips r
and firmly push onto locations.
MEASUREMENT
Measurement A:
37/64 in (14.5 mm)
MEASUREMENT
Measurement B:
6 9/64 in (156 mm)
MEASUREMENT
Measurement C:
6 9/64 in (156 mm)
MEASUREMENT
Measurement D:
25/32 in (20 mm)
Instr 9939998 Rev 01 2021-09 Page 6 of 18
LLIIGGHHTTIINNGG IINNSSTTAALLLLAATTIIOONN
NOTICE
Left side shown; right side similar
1. Put 2 foam pieces ton top of the saddlebag
light w, towards the outside edges of the light.
2. Test fit the foam tand saddlebag lighting w
with the saddlebag. Make sure that the foam on
top of the lighting is touching the lid of the
saddlebag.
IMPORTANT
Do not compress the foam.
3. Clean current side with 50:50 isopropyl alcohol/
water solution.
4. Remove the adhesive backer from the light w
and push the light on the saddlebag with the
foam tagainst the saddlebag lid. Hold for 30
seconds.
IMPORTANT
The adhesion will set in 72 hrs. Ideal temperature
range for adhesion application is 70-100°F (21–38°
C). Minimum temperature is 50°F (10°C).
5. Open saddlebag lid and remove foam pieces.
6. Route light harness through routing clips r.
Instr 9939998 Rev 01 2021-09 Page 7 of 18
SSAADDDDLLEEBBAAGG IINNSSTTAALLLLAATTIIOONN
ALL SADDLEBAGS
1. Set saddlebag in place.
2. Open saddlebag.
3. Install two retained screws A. Torque screws to
specification.
TORQUE
Saddlebag Screws A:
18 ft-lbs (24 N·m)
4. Repeat this section for opposite saddlebag.
HARD SADDLEBAGS ONLY:
1. Connect saddle bag lock wiring near seat.
2. Repeat this section for opposite side.
LLIIGGHHTT HHAARRNNEESSSS IINNSSTTAALLLLAATTIIOONN
NOTE
Left side shown; right side similar.
1. Connect light harness wto rear lighting harness
q.
Instr 9939998 Rev 01 2021-09 Page 8 of 18
VVEEHHIICCLLEE RREEAASSSSEEMMBBLLYY
WWIIRREELLEESSSS CCOONNTTRROOLL MMOODDUULLEE AANNDD KKEEYY FFOOBB
AANNTTEENNNNAA IINNSSTTAALLLLAATTIIOONN
1. Insert wireless control module.
2. Connect wireless control module connector.
3. Insert key fob antenna at an angle.
4. Make sure that it is flat against the surface by
moving it down until it touches the bracket.
5. Pull up wires to the appropriate location.
6. Connect the key fob antenna connector.
Instr 9939998 Rev 01 2021-09 Page 9 of 18
IINNSSTTAALLLL SSEEAATT
1. Lower seat onto fender with rear hook behind
frame mount. Pull seat forward to engage frame
mount until screw holes line up with seat bracket
holes.
2. Install two retained screws into seat brackets
and torque to specification.
TORQUE
Seat Bracket Screw:
18 ft-lbs (24 N·m)
SSIIDDEE CCOOVVEERR IINNSSTTAALLLLAATTIIOONN
NOTICE
Left side shown; right side similar.
1. Attach the panel by aligning the three grommet
pins and pushing it in. Use caution to prevent
damage to painted surfaces.
Instr 9939998 Rev 01 2021-09 Page 10 of 18
IINNDDIIAANN CCHHIIEEFFTTAAIINN®®//RROOAADDMMAASSTTEERR®®
VVEEHHIICCLLEE PPRREEPPAARRAATTIIOONN
GGEENNEERRAALL
1. Park motorcycle on a flat surface, fully extend
kickstand, and make sure vehicle is stable.
2. Turn key or ignition switch to OFF position and
remove key. If equipped with keyless fob,
remove fob from proximity of vehicle.
RREEMMOOVVEE SSIIDDEE CCOOVVEERRSS
1. Remove side covers by grasping firmly and
pulling outward. Carefully set aside.
TTRRUUNNKK RREEMMOOVVAALL
NOTICE
Right side shown; left side similar.
1. If equipped, remove and keep security screw
from trunk base latch.
2. Disconnect trunk harness connector underneath
trunk..
3. Lift both trunk base latches.
4. Lift trunk off rear posts and remove from front
posts toward rear.
5. Carefully set trunk aside.
Instr 9939998 Rev 01 2021-09 Page 11 of 18
SSEEAATT RREEMMOOVVAALL
1. Remove and keep one bolt Afrom each side of
seat.
2. If removing a touring (2-person) seat, remove
one bolt Band two washers Cand Dfrom rear
fender.
3. Slide seat rearward while lifting on rear and
remove seat.
OPTIONAL
1. Remove seat strap, if equipped, by removing
two screws E.
UUNNDDEERR SSEEAATT BBRRAACCKKEETT RREEMMOOVVAALL
1. Remove and retain top bracket screw.
2. Disconnect vehicle control module connectors.
Instr 9939998 Rev 01 2021-09 Page 12 of 18
3. Remove and retain bottom wire screw and
washer.
4. Move wire away towards bottom.
5. Move down bracket.
6. Tilt up bracket and remove.
SSAADDDDLLEEBBAAGG RREEMMOOVVAALL
HARD SADDLEBAGS ONLY:
1. Unlock electric saddlebag lock (if equipped).
TIP
Provided key can also be used in latch release
buttons to unlock saddlebag lids.
2. Disconnect saddle bag lock wiring near seat.
3. Repeat this section for opposite side.
ALL SADDLEBAGS
1. Open saddlebag.
Instr 9939998 Rev 01 2021-09 Page 13 of 18
2. Remove and keep two screws A.
3. Tilt saddlebag away from frame and remove
from vehicle.
NOTE
Lift leather saddlebags up-and-off spools before
tilting off frame.
4. Repeat this section for opposite saddlebag.
AACCCCEESSSSOORRYY IINNSSTTAALLLLAATTIIOONN
NOTICE
Left side shown; right side similar.
HHAARRNNEESSSS IINNSSTTAALLLLAATTIIOONN
1. Route harness qthrough both left and right
frames.
IMPORTANT
The rear lighting wire harness should be routed
over both the positive battery harness and the
shock hose. Failure to do so may cause the harness
to become pinched in the shock.
Instr 9939998 Rev 01 2021-09 Page 14 of 18
RROOUUTTIINNGG CCLLIIPP IINNSSTTAALLLLAATTIIOONN
1. Clean the inboard side with 50:50 isopropyl
alcohol/water solution.
WARNING
Isopropyl alcohol is hazardous to your health. See
isopropyl alcohol packaging for proper handling
instructions, including recommended personal
protective equipment such as goggles and
chemical resistant gloves.
2. Remove adhesive backer from routing clips r
and firmly push onto locations.
MEASUREMENT
Measurement A:
37/64 in (14.5 mm)
MEASUREMENT
Measurement B:
6 9/64 in (156 mm)
MEASUREMENT
Measurement C:
6 9/64 in (156 mm)
MEASUREMENT
Measurement D:
25/32 in (20 mm)
Instr 9939998 Rev 01 2021-09 Page 15 of 18
LLIIGGHHTTIINNGG IINNSSTTAALLLLAATTIIOONN
NOTICE
Left side shown; right side similar
1. Put 2 foam pieces ton top of the saddlebag
light w, towards the outside edges of the light.
2. Test fit the foam tand saddlebag lighting w
with the saddlebag. Make sure that the foam on
top of the lighting is touching the lid of the
saddlebag.
IMPORTANT
Do not compress the foam.
3. Clean current side with 50:50 isopropyl alcohol/
water solution.
4. Remove the adhesive backer from the light w
and push the light on the saddlebag with the
foam tagainst the saddlebag lid. Hold for 30
seconds.
IMPORTANT
The adhesion will set in 72 hrs. Ideal temperature
range for adhesion application is 70-100°F (21–38°
C). Minimum temperature is 50°F (10°C).
5. Open saddlebag lid and remove foam pieces.
6. Route light harness through routing clips r.
Instr 9939998 Rev 01 2021-09 Page 16 of 18
SSAADDDDLLEEBBAAGG IINNSSTTAALLLLAATTIIOONN
ALL SADDLEBAGS
1. Set saddlebag in place.
2. Open saddlebag.
3. Install two retained screws A. Torque screws to
specification.
TORQUE
Saddlebag Screws A:
18 ft-lbs (24 N·m)
4. Repeat this section for opposite saddlebag.
HARD SADDLEBAGS ONLY:
1. Connect saddle bag lock wiring near seat.
2. Repeat this section for opposite side.
LLIIGGHHTT HHAARRNNEESSSS IINNSSTTAALLLLAATTIIOONN
NOTE
Left side shown; right side similar.
1. Connect light harness wto rear lighting harness
q.
Instr 9939998 Rev 01 2021-09 Page 17 of 18
VVEEHHIICCLLEE RREEAASSSSEEMMBBLLYY
UUNNDDEERR SSEEAATT BBRRAACCKKEETT IINNSSTTAALLLLAATTIIOONN
1. Insert under seat bracket
2. Move up underseat bracket until the bottom
notch is inserted into the bracket
3. Line up bottom wire with hole. Install wire screw
and washer.
4. Connect vehicle control module connectors.
5. Install top bracket screw.
SSEEAATT IINNSSTTAALLLLAATTIIOONN
1. Install seat in place and slide seat forward until
mounting holes line up. If installed, pull
passenger strap through opening in seat..
Instr 9939998 Rev 01 2021-09 Page 18 of 18
2. Install one bolt Ainto each side of seat. Torque
fastener to specification.
TORQUE
Seat Fastener A:
18 ft-lbs (24 N·m)
3. If installing a touring (2-person) seat, install one
bolt Band two washers Cand Dinto rear
fender.
TORQUE
Passenger Seat Fastener B:
84 in-lbs (9.5 N·m)
IINNSSTTAALLLL SSIIDDEE CCOOVVEERRSS
1. Install side covers by aligning pins with rubber
grommets and pressing into place.
IINNSSTTRRUUCCTTIIOONN FFEEEEDDBBAACCKK FFOORRMM
A feedback form has been created for the installer to provide any comments,
questions or concerns about the installation instructions. The form is viewable
on mobile devices by scanning the QR code or by clicking HERE if viewing on
a PC.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Indian Motorcycle 2889224 Saddlebag Light Kit is designed to enhance the visibility and safety of your motorcycle. With its easy installation process, you can quickly add bright LED lights to your saddlebags, improving your visibility to other road users and increasing your riding confidence. The kit includes all necessary hardware and detailed instructions to guide you through the installation process, ensuring a secure and proper fit.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Indian Motorcycle Indian INTL Rider's Owner's manual
-
Indian Motorcycle Springfield Owner's manual
-
-
-
Indian Motorcycle Chief / Chieftain / Roadmaster Owner's manual
-
Indian Motorcycle Vintage Dark Horse Owner's manual
-
Indian Motorcycle Roadmaster Owner's manual
-
-
-
Indian Motorcycle Roadmaster Owner's manual
Other documents
-
Custom Dynamics Saddlebag LED Dual Color User manual
-
-
-
Custom Dynamics CD-SBL-BCM User manual
-
Custom Dynamics Saddlebag LED Latch Lightz User manual
-
Kawasaki CONCOURS 14 ABS Owner's manual
-
Polaris Indian Owner's manual
-
-
-