Tripp Lite 2342M User manual

Tripp Lite
Brand
Tripp Lite
Model
2342M
Category
Flat panel wall mounts
Type
User manual

This manual is also suitable for

Tripp Lite DWM 2342M can support TVs and LCD panels with a maximum load capacity of 50KG/110lbs. The screw size range is 23" to 42", and the adjustable angle is ±10°. The wall plate measures 548x195x25mm, and the left/light TV rail measures 428x70x65mm. The package includes various hardware, such as lag bolts, concrete anchors, plastic spacers, machine screws, washers, and an Allen key. The installation process involves drilling holes in a concrete or wooden wall, mounting the wall plate, attaching the rails to the TV or LCD panel, and finally, mounting the plate to the arm assembly.

Tripp Lite DWM 2342M can support TVs and LCD panels with a maximum load capacity of 50KG/110lbs. The screw size range is 23" to 42", and the adjustable angle is ±10°. The wall plate measures 548x195x25mm, and the left/light TV rail measures 428x70x65mm. The package includes various hardware, such as lag bolts, concrete anchors, plastic spacers, machine screws, washers, and an Allen key. The installation process involves drilling holes in a concrete or wooden wall, mounting the wall plate, attaching the rails to the TV or LCD panel, and finally, mounting the plate to the arm assembly.

C31357A
73103M-26
SC30764-100
SC30764
SC30764
SC30764-100
73103M-26
DWM 2342M
INSTALLATION GUIDE
Max load capacity:50KG/110lbs
Screw size range:23"-42"
Adjustable angle: ±10°
IMPORTANT:If necessary, please consult a professional installer
if these instructions do not apply to your mounting
application.
4
7MM lag bolt Ø7X64mm
concrete anchor
Ø13X57mm
plastic spacer
Ø16X20mm
plastic spacer
Ø12X13mm
Install sleeve
machine screw
Ø8X40mm
machine screw
Ø8X25mm
machine screw
Ø6X30mm
washer
Ø18X1.5mm 6mm
washer
Ø20X1.5mm 8mm
plate
548x195x25mm T:2mm
left/light TV rail 428x70x65mm T:2mm
washer Ø15X1.5mm 5mm
PACKAGE CONTENTS
4
4
4
1
4
4
4
4
8
4
1
2
NO.
Apperance
Qty
Description
Size
1
wall plate
V
4
S
R
4
4
SC30764
2
Allen Key 6mm
C31357A
C31620-300
C31213-300
SC30764-100
SC10840
SC10825
SC10630
A106-100
SC11815-200
SC13015-200
SC11515-200
703103M-24
703103M-25
73103M-26
1、Using a level, place the wall plate against the wall
and mark the position of the holes to be drilled.
2.75"(70mm)
concrete wall
wood wall
Ø12(15/32)
Ø6(15/64)
2、Drill 2.75"(70mm) deep holes with a ∅12 bit.(If you
installthe wall plate in a wooden wall,Use a ∅6 bit.)
3、Mount the wall plate using the hardware as
shown below.
concrete wall
wood wall
SC13015-200
SC13015-200
2.75"(70mm)
R
V
73103M-26
S
C31620-300
C31213-300
703103M-25
PLASMA
5、Mount the plate to the arm assembly. Level the plate
and tighten the mounting hardware.
6、Put the TV or LCD panel onto the plate using the
hooks. Once positioned, tighten the lower screws
shown to lock the rails into place.
4、Using the correct length hardware, mount the
rails to the TV or LCD panel. Determine the
amount of tilt you need before tightening.
10.0°
10.0°
703103M-24
703103M-25
703103M-25-1
！ WARNING:
4、For added security, always use the included
Allen wrench to tighten the hardware by hand.
2、Do not over tighten the mounting hardware.
3、Completely remove the the TV or LCD panel
before loosening any of the mounting screws.
1、It is not recommended to use this mount
on hollow walls. Always mount to concrete,
brick or wall studs.
703103M-25
-2
548
MAX=500 MIN=50
100
220
428
±
10
°
±
90
°
The viewing angle can be adjusted
by loosen or tighten 703103M-25-2.
SC10840
SC10825
SC10630
SC11815-200
SC13015-200
SC11515-200
703103M-24
  • Page 1 1
  • Page 2 2

Tripp Lite 2342M User manual

Tripp Lite
Brand
Tripp Lite
Model
2342M
Category
Flat panel wall mounts
Type
User manual
This manual is also suitable for

Tripp Lite DWM 2342M can support TVs and LCD panels with a maximum load capacity of 50KG/110lbs. The screw size range is 23" to 42", and the adjustable angle is ±10°. The wall plate measures 548x195x25mm, and the left/light TV rail measures 428x70x65mm. The package includes various hardware, such as lag bolts, concrete anchors, plastic spacers, machine screws, washers, and an Allen key. The installation process involves drilling holes in a concrete or wooden wall, mounting the wall plate, attaching the rails to the TV or LCD panel, and finally, mounting the plate to the arm assembly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents