Haier HWM75-7288 User manual
- Category
- Washing machines
- Type
- User manual
Haier HWM75-7288 is a fully automatic washing machine with a range of features to make laundry day easier. It has a large capacity, so you can wash a lot of clothes at once, and it's energy-efficient, so you can save money on your utility bills. The HWM75-7288 also has a variety of wash cycles, so you can choose the right one for your clothes, and it has a built-in lint filter to remove lint and debris from your laundry.
Haier HWM75-7288 is a fully automatic washing machine with a range of features to make laundry day easier. It has a large capacity, so you can wash a lot of clothes at once, and it's energy-efficient, so you can save money on your utility bills. The HWM75-7288 also has a variety of wash cycles, so you can choose the right one for your clothes, and it has a built-in lint filter to remove lint and debris from your laundry.
User’s Manual
Fully Automatic Washing Machine
This manual is for
HWM75-7288
Please read this manual carefully before using.z
Retain it for future reference.z
Index
Safety precautionsy ...............
2
Packing listy ...........................
4
Names of the partsy ...............
4
Installation andy
adjustment............................
5
Preparation beforey
washing .................................
9
Usetheoperationbuttonsy ....
11
Disposal after washingy .........
13
Trouble-shooting Answery
to question............................
14
SpecL¿cationy .........................
15
0030808632
2
Safety precautions
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
ofthemachineorinjurethepersonalsafety of theuser.
FORBIDDEN
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
WARNING
Meaning and description of the symbols
Pleasecheckifpowerreceptaclehasgoodearthingconditionbeforeusingtoguaranteez
your safety.
Pleasecheckifthewaterfaucetisopen,andiftheconnectionofthewaterinletpipeisz
proper.
Itissuggestedtousefoamlesswashingpowder.z
Pleasedon’tusethewasherintheenvironmentbelow 0 °C;ifthewasherhasbeenstoredz
below0°C,pleasebesuretoensurethewasherisplacedundertheroomtemperature
more than 2 hours and then use otherwise the washing effects may be lowered or the
washer may be damaged.
Pleaseinsertthepowercordintospecialreceptaclewithrated voltage.z
Be sure to use single-phase three pins receptacle.The earthing terminal of
the receptacle must be earthed reliably. If possible,please adopt electric
leakage protector.
Thewashingmachinemustbepositionedsothattheplugisaccessible.Bez
suretopulltheplugoffandclosethewaterfaucetinfollowingcases:power
failure, delivering the machine, setting the machine idle or cleaning the
machine.
Donotplugorpullthepowerplugwithwethand.z
Donotbend,extend,twist,bindbyforce.Donotpressornipitwithweight.z
Keep the pin of the power plug clean, if the power plug is polluted with dust,z
please wipe with dry cloth carefully.
Ifthesupplycordisdamaged,itmustbereplacedbythemanufactureroritsz
service agent or a similarly qualL¿ed person in order to avoid a hazard.
Do not let the machine share one receptacle with otherz
electric appliances. If the plugging into the receptacles
loose, do not use the plug any more.
3
In case the washing machine is installed on groundz
with carpet, do not block the ventilation hole
with carpet. Ensure carpet does not obstruct the
openinginthebases.
Do not put the machine at damp place like thez
bathroom. Never wash it with water. Do not put wet
laundries on the control panel.
Do not wash water-proof laundries like the raincoat,z
bikecoversetc.toavoidabnormalvibrations
in spinning. Wash the clothes that can Àoat
onthewatersurfaceeasily,pleasebecareful
especially,for fear damage.
Donotstretchhandsintotheworkingmachine.Itisz
dangerous even if the rotation is slow. Take special
care of the children.
Donotputanyhotorheavyitems(suchasthez
kettle with hot water ) on the washing machine.
Do not wash laundries with volatile materials (suchz
as thinner, petrol etc.)
Thechildrenshallnotapproachtheworkingz
washing machine.
Keep the machine away from direct sunlight andz
heat source like the heater.
Do not decompose, repair or alter the machine byz
yourself.
Donotusewaterhotterthan50°C.z
$OFRKRO
4
Names of the parts
Packing list
Fully automatic
washing machine
Water inlet hose Bottom plate Tapping screws
(One Piece)
User’s manual
Warranty card
Screw cover(left)
Water inlet valve
Water absorption cushion
Back control board
Power line
Back cover
Drain hose
Bleach inlet
Hanging hole
Cabinet handle
Screw cover(right)
Adjustable foot ¿lm(2 pieces)
Top lid
Detergent box
Control panel seat
Outer tub cover
Lint ¿lter(2 pieces)
Balance ring
Inner tub
Filter cover(2 pieces)
Pulsator
Control panel ¿lm
Cabinet
Fixed foot (2 pieces)
Adjustable foot(2 pieces)
AllillustrationsinthisManualarez
givenforreferenceonly.Your
products and accessories may
showdifferencesfromthese
illustrationsduetoourcontinuous
improvement.
5
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important
to your security and correct operating the machine.
Adjust the adjustable foot:z
To twist the adjustable foot, please ¿rst lift up the side of the foot slightly, and then you
can twist the two adjustable feet. Please make sure to keep the washing machine
in balance.
The adjustable foot
Thewashingmachineawayfromwallshouldbeoverrun20mm.Thelargestallowableslope
of the shank base of the machine is 2°. The slanting or rough ground will result in unstable
runningorstoppageofthemachine.Pleaseadjustitwithfollowingmethods:
Confirm
it's horizontal:
Hang the lead line to check if it is horizontal.
z
Soft items
Back
Front
Bottom plate
Section I enlarging
After you open the package, please lean
the washing machine gently down on soft
items (like the towel cloth, blanket, ect. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Fasten the bottom plate to
base frame with one screw
High
Low
6
Screw knife
Figure 4
Figure 5
About 4mm before twisting
About less than 2mm after twisting
Screw
Bushing
Sign plate
Screw nut
Figure 2
Figure 3
Figure 6
2.Loosen the screw till the water faucet can be
accessed. Put the jointer of the water inlet
hose on the faucet. See to Figure 2. (If the
faucet is too large and the jointer can not be
set on the water faucet,please loosen the four
screws and take out the bushing in the jointer.
The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut
as per the indication of the figure to seal up the
exit end face of the faucet. See to Figure 5.
Remark: Before installation, the threading is
4mm above the upper surface of the nut.After
installation, the threading is 2mm above the
upper surface of the nut.See to Figure 6.
Connection between the water inlet hose jointer and the
water faucet
1.Press the lower end of the lock lever and push
down the slider. Take off the water inlet hose
jointer from the water inlet hose component.
See to Figure 1.
water inlet hose jointer
water inlet hose
Figure 1
Slider
Lock lever
The exit end face of the faucet
water faucet, suitable
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth.If not please file it to avoid leakage.
Confirm the water faucet
z
z
water faucet, not suitable
NOTE:The appliance is to be connected to the water mains using new hose-sets and
that old hose-sets should not be reused.
1.Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it happens please contact our
after-sale department immediately.
2.Put the nut of the water inlet hose on the valve
jointer.
3.Fasten the nut. Swing it gently to confirm if it's
suitable.
1.
Push down the slider. Insert the water inlet hose
into the jointer.
2.Hang the lock lever to the jointer. Release the
slider till a click sound is heard.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection between
the jointer of the water inlet hose and the water faucet, and
the installation of the water inlet hose are firm, so as to
prevent dropping from improper installation position.
1.Close the water faucet.
2.Press the locking lever. Push down the slider.Then pull off the water inlet hose.
If the machine is used frequently, the jointer of the water inlet hose can be kept
on the faucet to prevent damaging the fixing screw.
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose and the
water inlet hose
Check the connection between the jointer of the water inlet hose
and the water faucet
Locking lever
Slider
water absorption
cushion
nut of the water
inlet hose
The jointer of the
water inlet hose
Slider
Locking lever
jointer of the
water inlet valve
Connection between the water inlet hose and the washer
7
8
The drain hose shall drain smoothly.
Do not trample or press the drain hose.2.Theheightofthedrainhoseshallbeless
than10cm , orthedrainagewillnotbesmooth,
and cost such long time that the machine may
stop at mid way.
1.
3.
5.
4.
If the drain hose is too long, cut it at mid
point. To make smooth drainage,cut the front
end of the hose slantingly.
If the extra hose is too long,cut it either at A or at B point.
If extra drain hose is needed,please
make separate purchase.The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
Remark: In order to make sure of the correct of installation, it is suggested to change the
direction of the drain hose with our company serviceman.
1.Dismantle the back cover of the washing machine.
2.Press the spring lamination lightly and pull the top
segment of the drain hose decumbent then put
down the drain hose from the drain hose frame.
3.Put down the drain hose, squeeze the drain hose
lightly and take off the hook, put the drain hose into
the cabinet. Take off the small baffle which installed
on the other drain outlet and install it on the side
which won't install the drain hose.
4.Extend the drain hose from the other side and install
it on the base by the drain hose frame
5.Install the back cover.
How to change the direction of the drain hose
Back cover
Drain hose frame
Spring lamination
9
Preparation before washing
Connect the water inlet hose. Open the water faucet.z
Con¿rmthatthewashingmachineisearthedreliably.Theninsert
thepowerplugintothereceptacle.Theearthterminalshallnot
link to gas pipeline and faucet water pipeline.
z
Put down the drain hose.z
Slanting or uneven ground may result in unstable working or
abnormal noise. Please make the machine stand horizontally.
z
Clear the pocket. Take out the coins,sand, hairpins etc.
Confirm if there is special requirement for the laundries.
Checkifthelaundriesareapplicableforwashingwithmachine.z
Pleaserepairthedamagedclothbeforewashinginorderto avoidthesituationworse.z
Dividethelaundriesthatarenotcolorfastfromotherlaundries.z
Put those laundries dif¿cult to absorb water into water with hand.z
For those laundries with heavy soil, please ¿rst remove the dirt like mud or dust. For the parts
with heavy soil, please apply detergent on them in advance, which can make it easier to remove
the soil.
z
Forthoselaundriesthatmaygetlintballandthosewithlongfur,turnit overbeforeputtingin.z
Donotputthoselaundriespollutedbychemicalsintothewashingmachinedirectly.z
Theforeignmaterialswillresultindamageofthemachine.z
The quantity of the laundries shall not be too large. Stretch and loosen the
laundries before putting them in the tub.
Whenthepulsatorisrunning,thebuttonsofthelaundriesmaycausenoise.
For the sake of discretion, please put the laundries with buttons into other
laundries.
Tie the long strips; fasten the buttons;close zippers.
Pay attention to followings before washing the laundries
10
Howtousethewhitener
Howtousethewashingpowder
Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub.z
Avoid using whitener on laundries with color or pattern as they are prone to lose color.z
The whitener shall not touch the laundries directly.z
Refer to the user’s manual for the usage and quantity of the whitener.z
Forpowderwhitener,pleasedissolveitbeforeusing.z
Directlydissolvedinthemachine:(notapplicableforfuzzyprogram )z
.retawfoytitnauqllamslliF.1
completelytievlossidotsdnoces03rofnuR.redwopehtddA.2
.levelretawelbatiu
stceleS.seirdnualehtnituP.3
Theinstantdissolvingofthewashingpowder:z
.reniatnocadnaC°03foretawmraweraperP.1
.tievlossidyllufotgnirritselihwredwopehtddA.2
Thequickprogram,itissuggestedtoadoptliquiddetergentinsteadofz
washingpowdertoguaranteethewashingeffect.
Put in the proper quantities detergent according to the water level and thez
laundries quantities.
It is suggested not to use high sudsingz
detergent. Washing powder with poor
qualityorlongtimestoragemaybecaked.
Please pay attention to cleaning the
detergent box in time.
Thecapacityofwashingandspinningofhemachinerefertothelargestweightz
ofthestandardlaundriesunderdryconditionthatcanbewashedorspinnedinone
time. One time washing quantity shall be lower than the rated capacity.
The thickness, size, type of the cloth will inÀuence the actual washing capacity. Itz
is suitable for one time washing to put in reasonable amount of laundries and the
laundries can be turned round in washing.
Do not select the high water level for laundries less than 1.0kg ,so as to avoidz
splashing of water.
Figure 1
Figure 2
Open
Close
Access for softener
Control panel seat
Bleach inlet
How to use the softener
Theusageanddoseofthesoftener
as per the speci¿cations of softener.
z
Turn the inner tub,you will find a
softener inlet as the figure 1,open
the cover,put the softener into the
inlet as the figure 2.Before washing,
close the cover and the softener will
drop into the inner tub during the
last time rinsing.
z
After the softener is put in,please
don’t place for a long time otherwise
softener may solidify and cause
flowing not smooth.
z
Don’t put in the softener if the quick program is selected.
z
11
Use the operation buttons
Off
On: indicate the program about to run,or indicate
theselectedmodeorindicatethewaterlevel
Flashing: indicate the running program
It displays “--” during detecting.z
Itdisplaystotalremainedtimeduringthez
running program (min).
It displays remained reserved time duringz
reserve program hour
It displays abnormal symbol in abnormalz
situation.(See to Page 14)
Program Applicable situation
SOAK Washing the relatively big thick or very
dirty laundries
STANDARD Common washing
If “STANDARD” program is set, the
machinewillexecutefuzzydetection.The
computer will set the water level and
washing time as per the cloth and quantity
of the laundries.The whole procedure is
under automatic control.
SOFT Washingthewoollentextiles
QUICK Posthaste wash of the laundry under 2.0
kg with light soil.
Thewaterlevelwillautomaticallyset24L.
WASH Justrunthewashingcyclewithout
drainage cycle. The detergent was left
insidethedrumandcanberecycled.
RINSE Remove the left detergent from the clothes
andthenrinsetheclothes
SPIN Whentheclothesarewashedorthe
clothes are quite wet, extra spin is needed.
TUB DRY Drying the inner tub and the outer tub,
which can avoid growing mildew.
Afterthepowerisswitchedon,pressittostart
the machine.
During working, push it to pause.z
Duringpause,pushthisbuttontorestartz
andgoonworking
PushtheOn/Offbuttontoswitchonthez
power.
Whenthepowerison,pushitagaintoz
switch off the power.
thepower.Ifthestart/pausebuttonis
not pushed, the washing machine will
z
automatically switch off the power
after 5 minutes.
Thedigitrondisplaysthetimeremainedz
(inminute)beforethewashingis¿nished.
Push down the reserve button. The reservez
indicator light is on the digitron displays the
reservetimeof¿nishing washing (in hour).
When the machine is started, the reservez
indicator light is on, indicating that the
reservefunctionisrunning.
The washing machine can detect thez
laundries automatically during the
STANDARD program After detection,
it will set the water level to suitable value
among 30L,40L and 50L automatically.
You can also set water level by yourself.z
Afterthemachineisstarted,itwillnotset
water level automatically. You shall push
the start/pause button to make new setting.
If there’s water inside the tub, the machinez
cannotdetectthelaundriesandwilldisplay
waterlevel40L.Ifwetlaundriesareputin,
it may display water level 50L. You must
setsuitablewaterlevelbyyourself.
If quick program is selected, it will displayz
water level 24L.
Iftubdryprogramisselected,thewaterz
levelwillnotrespond.
Duringoperationofwashandrinsez
program,youcanpushdownthewater
levelbuttontoaddwater.Whenyou
releasethebutton,oritreachesthe
overÀowwaterlevel,themachinewillstop
adding water.
The water level decided may be differentz
from actual value because of the different
moisture level of the laundries.
The rinsing water level is one water level
higher than the washing water level( except
the maximal and man-rated water level).
z
PushtheOn/Offbuttontoswitchon
12
Push “
” button to switch on the power
Push “
” button, select suitable water level
Push “
” button to select suitable reserve wash program
Push “
” button to select suitable automatic program
Afterthepowerisswitchedon,“SOAK”isautomaticallyset.Toselectotherfully-autoz
program, please push the “PROGRAM” button till the corresponding indicator is on.
Refer to the “Program” button on Page 11.
Whenthe“soak”isselected,afterthewaterstarttojet,theprogramwash,rinseandz
spinwillbeimplemented(lowwaterlevelsoakfor25minutes,midlevel35minshigh
level 45 mins).
PushPROGRAMbuttonfor 8 times,anditwillresumetheinitialmode.Itwillcirculatez
in that sequence.
Water pressure and water level inÀuence the washing time.z
Eventhere’snowaterinthetub,thespinningwillstartafter a certainperiod.z
Washandspinafterputtingthedamageableclothesintotucknet,toavoidscathe.z
Wash the laundries that are prone to lose colors separately from other laundries.z
Whenwashingstartoropeningcoverintermitting,thewashingmachinewillbegintoz
work after a period time, this is normal phenomenon.
Only select RINSE program,If there’s water inside the tub, the machine will spin beforez
rinsing,Ifthere’snowaterthemachinewillrinsedirectly.
After switching on the power, the washing machine will execute fuzzy program z
automatically to detect the cloth during the standard program. After defection, it can set
the water level automatically. To select other water level, ¿rst push the “START/PAUSE”
button, then push the “ WATER LEVEL ” button to set the water level.
The pulsator will not rotate unless the water is ¿lled to selected water level.z
After switching on the power, the reserve program is set to off mode automatically. If you
need to set the washing procedure to be ¿nished at reserved time, please push the
“ RESERVE ” button to set the reserve wash program. Refer to reserve button in Page 11
for selection.
Con¿rm the operation of reserve program
When the “z RESERVE” function is activated, the indicator light of
the program you have set will be off. The “RESERVE (HOURS)” and
“REMAIN MINUTES” indicator lights will be on. During reserve procedure,
push the “RESERVE” button to display the reserve time mode.
To change the running program or cancel the reserve setting, you z
need to switch off the power and make new selection.
1
3
4
2
Push “ ” button, close the top lid
Finish washing
If the top lid is opened when the machine is spinning, the machine will stop running z
and alarm.
After Finishing washing, it will switch off power automatically.z
5
6
13
Disposal after washing
Please ¿rstpulloffthepowerplugfromthereceptaclebeforecleaning.z
Afterusing,pleasecleanthelintandforeignmaterialsofthelint¿lter andz
overÀow ¿lter in time. Otherwise it may inÀuence your using the machine.
1
1
2
2
34
Themethodof
dismantle: Push it up
aslant and gently.
Themethodofinstall :
install it upwards and
aslant and push it in.
Clean the detergent box and set it on the control panel seat.
Cleaning the lint ¿lter
Push down the spring
piece of the top lint ¿lter
to make the claws out of
the ¿lter cover, and then
pull out the lint ¿lter to
getitdown.
Put the lint ¿lter into ¿lter
cover, and make it tight .
Make sure the lint ¿lter
well installed, or it can
inÀuence your use.
Pull the back of the lint
¿lter, and then you can
getdownitoffthefront
cover of the lint ¿lter.
Sweeptherubbishinthe
lint ¿lter.
Put the back of the lint
¿lter into the front cover .
Notes:
The ¿lterscreenofthewaterinletvalveislikelytobeblockedbyforeignmaterialsandz
inÀuencethewaterinlet.Pleasecleanitwithbrusheverytwo
months.
If the cabinet is dirty, wipe it with wet clothz
Do not Àush it directly with water.z
Wipe it with neutral detergent.z
Donotwipeitwiththinner,petrol,alcoholetc.z
After washing, close the water faucet.z
(Ifneeded, youcandismantlethewaterinlethose).
Do not store water in the washing machine for a long period.z
Drain the water completely after each using.
Besuretopulloffthepowerplugbeforemaintenance.z
Hang up the power cord.z
Wipeoffthewaterdropsonthesurfaceofthemachineandinsidethetub.Openthetoplidz
for some time ( about 1 hour), then close the top lid.
Thinner
Petrol
Alcoho
14
Trouble-shooting Answer to question
Phenomena The reason How to settle
ThedigitrondisplaysE0. ƔThetoplidisopenedduring
reserve procedure.
Closethetoplid.Ź
Thedrainagecannot
work,oristooslow.The
digitron displays E1.
ƔIs the drain hose blocked?
ƔIs the drain hose put down?
Cleantheforeignmaterial.OpenandŹ
closeThetopLidOnce.
It stops running in
midway. The digitron
displays E2.
ƔThetoplidisnotclosed. Closethetoplid.Ź
Thesafetyswitchacts,
and the spinning cannot
work. The digitron
displays E3.
ƔAre the laundries put slantingly?
ƔIs the machine slanting?
Reorder the laundries. Close the top lid.
Ź
The machine will start running after 10Ź
seconds of being placed horizontally.
The water ¿lling does
notwork,orisslow,the
digital displays E4.
ƔIs the water tap opened, or is
therewatersupplyfailure?
ƔIsthewaterinletvalveblocked?
ƔIsthewaterpressuretoolow?
Openthewatertap.Pushthestart/
Ź
Pausebuttononce.
Cleanthewaterinletvalvethenpush
Ź
the start/Pause button once.
Useafterthewaterpressureisnormal.
Ź
ThedigitrondisplaysE6. ƔThe water level sensor is bad. Please contact the after-sales serviceŹ
department.
The
machine
does not
act
Not wash
ƔIs there power failure?
ƔIs the power plug inserted tightly?
ƔIs the water level reached preset
position?
Pleaseuseitwhenthere’spower
Ź
supply.
Insert the power plug tightly.
Ź
Fill water to the preset position.Ź
Not spin ƔIs the power plug inserted tightly?
ƔIsthetoplidclosedreliably?
ƔAre the laundries set Àat?
Insert the power plug tightly.
Ź
Closethetoplid.Ź
Set the laundries Àat.Ź
There’s abnormal sound
inside the machine
ƔIs the machine slanting?
ƔAre the laundries put slantingly in
spinning?
ƔAre there any foreign materials?
Adjust the machine to be even.
Ź
Ź
Reorder the laundries and close the
top lid.
Remove the foreign materials.
Ź
(If there’s breakdown, please pull off the power plug before checking)
The following phenomena are not breakdowns sometimes. Please con¿rmagainbeforesendingitto
repair.
Iftherearerealbreakdowns,pleasecometothespecialmaintenancedepartmentorafter-sale
servicedepartmentofourcompany.Donotrepairitby yourself.
The water tap leaks ƔIs the jointer of water inlet hose
loose or awry?
Fasten the jointer properly.Ź
ŹPutdownthedrainhose.Open and
close the top lid once.
Speci¿cation
Rated voltage/Frequency 220-240V ~ /50Hz
Waterlevel / Waterquantity(about) 1/12L,2/18L,3/24L,4/30L,5/35L,6/40L,7/45L,8/50L
Injection pressure 0.03 MPa ~ 1.0 MPa
Max Washing/Max Spinning capacity 7.5kg/7.5kg
Phenomena Explanation
Thespinningisintermittentwhenitstarts. Balancethelaundriesto avoidslanting.
Pushthe“spin”buttontoselect“Spin”,butitdoesn’t
work.
Theprogramissettingthedraintime.Sometimeis
needed before it starts spinning.
The ¿nalspinningis¿nished,itbecomesrinsingand
begins to inlet water.
Because the washing clothes lean to one side,the
safety switch acts.After water ¿lling and running,
eliminating the eccentricity of washing clothes,then
beginningtospin.
15
There may be some water flowing out of the drain hose
in the first use of machine.
It is the water remained in the factory inspection of
performance.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Haier HWM75-7288 User manual
- Category
- Washing machines
- Type
- User manual
Haier HWM75-7288 is a fully automatic washing machine with a range of features to make laundry day easier. It has a large capacity, so you can wash a lot of clothes at once, and it's energy-efficient, so you can save money on your utility bills. The HWM75-7288 also has a variety of wash cycles, so you can choose the right one for your clothes, and it has a built-in lint filter to remove lint and debris from your laundry.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
