MultiSync
®
E Series
User’s Manual
MultiSync
®
E Series
User’s Manual
NEC Enterprise Series
Contents 1
Quick Start 2-3
Controls 4-5
Recommended Use 6-7
Specifications 8-9
Features 10
Troubleshooting 11
References 12
Limited Warranty 13
78131861 5/21/98, 2:22 PM1
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE
THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This
symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this
unit has been included. Therefore, it should be read carefully in order to avoid any problems.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouiller du Canada.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations
according to C.S.A. 22.2 #950.
Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele
Canadiens selon CAN/CSA 22.2 No. 950.
FCC Information
1.
Use the attached specified cables with the JC-1575VMA and JC-1746UMA
color monitors
so as not to interfere with radio and television reception.
(1) Please use the supplied power cable or equivalent to ensure FCC compliance.
(2) Shielded captive type signal cable.
Use of other cables and adapters may cause interference with radio and television
reception.
2.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician
for additional suggestions. The user may find the following booklet, prepared by the Federal
Communications Commission, helpful: ”How to Identify and Resolve Radio-TV Interference
Problems.“ This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
78131861 5/21/98, 2:22 PM2
Contents
Power Cord
Registration Card
MultiSync
®
E Series
User’s Manual
MultiSync
®
E Series
User’s Manual
NEC
Enter
prise
Series
— Important —
To help us in our continuing efforts to
better serve and support you, and to bring
you new and innovative products, please
take a few moments to register your new
NEC MultiSync monitor.
By returning this card, we confirm your
date of purchase and records the model
and serial numbers. This facilitates our
ability to process warranty claims,
especially if your original proof of
purchase is lost.
Thank you for your time and for choosing
an NEC MultiSync monitor.
THANK YOU FOR
CHOOSING AN NEC
MultiSync
©
MONITOR
PRODUCT REGISTRATION
SEE, HEAR AND FEEL THE DIFFERENCE.
™
NEC MultiSync Monitors
1
Your new NEC Technologies MultiSync
®
E Series monitor box*
should contain the following:
• MultiSync E Series Monitor with tilt/swivel base
MultiSync E500
™
, JC-1575VMA
MultiSync E700
™
, JC-1746UMA
• Power Cord
• Captive Signal Cable
• User’s Manual
• Registration Card
User’s Manual
Captive Signal Cable
* Remember to save your original box
and packing material to transport
or ship the monitor.
Note: You can now register your
product on the Internet at
http://www.prodreg.com/nec
78131861 5/21/98, 2:22 PM3
Quick Start
To attach the MultiSync
®
E Series monitor to your system, follow
these instructions:
1. Turn off the power to your computer.
2. If necessary, install the display card into your system. For more information,
refer to the display card manual.
3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the
connector of the display card in your system (Figure A.1). Tighten all screws.
For the Mac: Connect the MultiSync E Series Macintosh cable adapter (not
included) to the monitor connector on the Macintosh (Figure B.1). Attach the
15-pin mini D-SUB end of the captive signal cable to the Macintosh cable
adapter on the computer (Figure B.1). Tighten all screws.
NOTE: To obtain the MultiSync E Series cable adapter, call
NEC Technologies at (800) 820-1230.
4. Connect one end of the power cord to the MultiSync E Series monitor and the
other end to the power outlet (Figure C.1).
5. Turn on the monitor (Figure D.1) and the computer.
NOTE: If you have any problems, please refer to the Troubleshooting section of
this User’s Manual.
2
Figure A.1
15-pin mini D-SUB
Captive Signal Cable
78131861 5/21/98, 2:22 PM4
Quick Start
3
Power
Cord
Power Outlet
Figure D.1
RESETPROCEEDEXIT
CONTROL
MultiSync E
500
Figure C.1
Figure B.1
Computer
Mac Adapter
(Not included)
Captive Signal
Cable
15-pin mini D-SUB
78131861 5/21/98, 2:22 PM5
4
OSM
™
(On-Screen Manager) control buttons on the front of the monitor function
as follows:
EXIT Exits the OSM controls.
CONTROL § / ©
Moves the highlighted area left/right to select one of the controls.
CONTROL +/– Moves the bar in the + or – direction
to increase or decrease
the adjustment.
PROCEED Enters OSM menu and selects icons at the top of the menu.
RESET Resets the highlighted control to the factory setting.
Brightness/Contrast Controls
Adjusts the overall image and background screen brightness.
Adjusts the image brightness in relation to the background.
Size and Position Controls
Moves the image horizontally (left or right).
Moves the image vertically (up or down).
Increases or decreases the horizontal size of the image.
Increases or decreases the vertical size of the image.
Geometry Controls
The Geometry controls allow you to adjust the curvature or angle of the
sides of your display.
Increases or decreases the curvature of the sides either inward or outward.
Increases or decreases the curvature of the sides either to the left or right.
Increases or decreases the tilt of the sides either to the left or right.
Increases or decreases the top of the screen to be the same as the bottom.
Color Control/AccuColor
®
Control System
Two color presets select the desired color setting. Each color setting is
adjusted at the factory to the stated degree Kelvin.
R, G, B: NEC’s AccuColor Control System increases or decreases the
monitor’s red, green or blue color guns depending upon which is
selected. The change in color guns will appear on screen and the direction
(increase or decrease) will be shown by the bars.
Controls
78131861 5/21/98, 2:23 PM6
Tools
Degauss Control: Eliminates the buildup of stray magnetic fields that
alter the correct scan of the electron beams and affect the purity of the
screen colors, focus and convergence. When activated, your screen
image will jump and waver a bit as the screen is demagnetized.
Caution: Please allow a minimum of 20 minutes to elapse
between uses of the Degauss Control.
Indicates the frequency setting of the monitor.
IPM
™
System: On: The IPM System works normally and all stages
of energy savings are utilized.
Off: The Off Mode of the IPM System is not used.
NOTE: For standard systems and graphics boards, keep the
factory setting at ON.
Selecting ALL RESET allows you to reset all OSM
™
control settings back to
the factory settings except IPM System. Individual settings can be reset
by highlighting the control to be reset and pressing the RESET button.
5
Controls
78131861 5/21/98, 2:23 PM7
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC
®
E SERIES COLOR MONITOR:
• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside
and opening or removing covers may expose you to dangerous shock hazards
or other risks. Refer all servicing to qualified service personnel.
• Allow adequate ventilation around the monitor so that heat can properly
dissipate. Do not block ventilated openings or place the monitor near a
radiator or other heat sources. Do not put anything on top of monitor.
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may touch
dangerous voltage points, which can be harmful or fatal or may cause electric
shock, fire or equipment failure.
• Do not place any heavy objects on the power cord. Damage to the cord may
cause shock or fire.
• Do not place this product on a sloping or unstable cart, stand or table, as the
monitor may fall, causing serious damage to the monitor.
• Keep the monitor away from high capacity transformers, electric motors and
other devices such as external speakers or fans, which may create strong
magnetic fields.
• If possible, position the monitor so that it is facing the east to minimize the
effects of the earth’s magnetic field.
• Changing the direction of the monitor while it is powered on may cause image
discoloration. To correct this, turn the monitor off for 20 minutes before
powering it back on.
• The power cable connector is the primary means of detaching the system from
the power supply. The monitor should be installed close to a power outlet
which is easily accessible.
• Handle with care when transporting. Save packaging for transporting.
Immediately unplug your monitor from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the monitor.
• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet damaged.
• If the monitor does not operate normally by following operating
instructions.
Recommended Use
6
78131861 5/21/98, 2:23 PM8
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR
CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE
FOLLOWING WHEN YOU POSITION THE MONITOR:
Recommended Use
• Adjust the monitor height so that the top of the screen is at or slightly below
eye level. Your eyes should look slightly downward when viewing the middle
of the screen.
• Position your monitor no closer than 12 inches and no further away than 28 inches
from your eyes. The optimal distance is 18 inches.
• Rest your eyes periodically by focusing on an object at least 20 feet away.
Blink often.
• Position the monitor at a 90° angle to windows and other light sources to
minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do
not reflect on your screen.
• If reflected light makes it hard for you to see your screen, use an anti-glare filter.
• Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a
non-alcohol, neutral, non-abrasive cleaning solution or glass cleaner to
minimize dust.
• Adjust the monitor’s brightness and contrast controls to enhance readability.
• Use a document holder placed close to the screen.
• Position whatever you are looking at most of the time (the screen or
reference material) directly in front of you to minimize turning your head
while you are typing.
• Get regular eye checkups.
For more detailed information on setting up a healthy work environment, call NEC
at (800) 820-1230, NEC FastFacts
™
information at (800) 366-0476 and request
document #900108 or write the American National Standard for Human Factors
Engineering of Visual Display Terminal Workstations – ANSI-HFS Standard
No. 100-1988 – The Human Factors Society, Inc. P.O. Box 1369, Santa Monica,
California 90406.
7
78131861 5/21/98, 2:23 PM9
Specifications
8
Monitor MultiSync
®
E500
™
Notes
Specifications Monitor
Picture Tube Diagonal: 15 inch 90° deflection, 0.25 mm mask pitch,
Viewable Image Size: 13.8 inch CromaClear
™
CRT, medium-short persistence
Radius: 1080 mm phosphor, multi-layered, anti-static screen
coating, dark-tint screen, Invar Shadow Mask
and OptiClear
®
screen surface.
Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms
Sync: Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors Analog input: Unlimited number of Colors Depends on display card used.
Synchronization Horizontal: 31 kHz to 69 kHz Automatically
Range Vertical: 55 Hz to 120 Hz Automatically
Resolutions Supported 640 x 480 @ 60 to 120 Hz
Some systems may not support
Resolution based on
horizontal and
800 x 600 @ 55 to 108 Hz
all modes listed.
vertical frequencies only
832 x 624 @ 55 to 103 Hz
1024 x 768 @ 55 to 85 Hz .......................
NEC cites recommended resolution at
1152 x 870 @ 55 to 75 Hz
75 Hz for optimal display performance.
1280 x 1024 @ 55 to 65 Hz
Active Display Area Horizontal:
270 mm/10.6 inches Dependent upon signal timing used,
(Factory Setting) Vertical:
202 mm/8 inches and does not
include border area.
Active Display Area
280 mm/11 inches Dependent upon signal timing used,
(Full Scan)
210 mm/8.3 inches and does not
include border area.
Power Supply
AC 100 – 120 V, 50/60 Hz
Current Rating 1.8A @ 100
–
120 V
Dimensions
372 mm (W) x 402 mm (H) x 412 mm (D)
14.6 inches (W) x 15.8 inches (H) x 16.2 inches (D)
Weight 15.1 kg
33.2 lbs
Environmental Considerations
Operating Temperature: 10°C to +35°C
Humidity: 30% to 80%
Feet: 0 to 10,000 Feet
Storage Temperature: -20°C to +60°C
Humidity: 10% to 90%
Feet: 0 to 45,000 Feet
NOTE: Technical specifications are subject to change without notice.
78131861 5/21/98, 2:23 PM10
9
Monitor MultiSync
®
E700
™
Notes
Specifications Monitor
Picture Tube Diagonal: 17 inch 90° deflection, 0.25 mm mask pitch,
Viewable Image Size: 15.6 inch CromaClear
™
CRT, medium-short persistence
Radius: 1210 mm phosphor, multi-layered, anti-static screen
coating, dark-tint screen, Invar Shadow
Mask and OptiClear
®
screen surface.
Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms
Sync: Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors Analog input: Unlimited number of Colors Depends on display card used.
Synchronization Horizontal: 31 kHz to 82 kHz Automatically
Range Vertical: 55 Hz to 120 Hz Automatically
Resolutions Supported 640 x 480 @ 60 to 120 Hz
Some systems may not support
Resolution based on
horizontal and
800 x 600 @ 55 to 120 Hz
all modes listed.
vertical frequencies only
832 x 624 @ 55 to 120 Hz
1024 x 768 @ 55 to 100 Hz .....................
NEC cites recommended resolution at
1152 x 870 @ 55 to 89 Hz
85 Hz for optimal display performance.
1280 x 1024 @ 55 to 76 Hz
1600 x 1200 @ 55 to 65 Hz
Active Display Area Horizontal:
306 mm/12.0 inches Dependent upon signal timing used,
(Factory Setting) Vertical:
230 mm/9.1 inches and does not
include border area.
Active Display Area
316 mm/12.4 inches Dependent upon signal timing used,
(Full Scan)
237 mm/9.3 inches and does not
include border area.
Power Supply
AC 100 – 120 V, 50/60 Hz
Current Rating 1.8A @ 100
–
120 V
Dimensions
403 mm (W) x 426 mm (H) x 453 mm (D)
15.9 inches (W) x 16.8 inches (H) x 17.8 inches (D)
Weight 19.5 kg
43.0 lbs
Environmental Considerations
Operating Temperature: 10°C to +35°C
Humidity: 30% to 80%
Feet: 0 to 10,000 Feet
Storage Temperature: -20°C to +60°C
Humidity: 10% to 90%
Feet: 0 to 45,000 Feet
NOTE: Technical specifications are subject to change without notice.
78131861 5/21/98, 2:23 PM11
10
Features
CromaClear
™
CRT: Delivers images with more clarity than found in traditional
CRT’s. Phosphors appear elliptical when illuminated, resulting in screen images
with more depth and dimension.
OptiClear
®
Screen Surface: Reduces reflection and glare and increases contrast
without sacrificing focus level, clarity or brightness. Along with the flat square
technology CRT, a high contrast screen with 0.25 mm mask pitch delivers crisp,
clean text and graphics.
Invar Shadow Mask: Holes in the thin metal sheet behind the glass of the CRT
surface correspond to each phosphor dot on the inner surface of the CRT’s
faceplate, allowing the correct electron beam (red, green, blue) to hit the correct
color phosphor for improved focus, brightness and color.
AccuColor
®
Control System: Allows you to adjust the colors on your screen and
customize the color accuracy of your monitor to a variety of standards.
OSM
™
(On-Screen Manager) Controls: Allow you to quickly and easily adjust all
elements of your screen image via simple to use on-screen menus.
ErgoDesign
®
Features: Enhance human ergonomics to improve the working
environment, protect the health of the user and save money. Examples include
OSM controls for quick and easy image adjustments, tilt/swivel base for pre-
ferred angle of vision and compliance with MPRII guidelines for lower emissions.
Plug and Play: The Microsoft
®
solution with the Windows
®
95 operating system
facilitates setup and installation by allowing the monitor to send its capabilities
(such as screen size and resolutions supported) directly to your computer,
automatically optimizing display performance.
IPM
™
(Intelligent Power Manager) System: Provides innovative power-saving
methods that allow the monitor to shift to a lower power consumption level when
on but not in use, saving two-thirds of your monitor energy costs, reducing
emissions and lowering the air conditioning costs of the workplace.
Reduced Magnetic Field
™
Technology: Reduces magnetic and alternating electric
field emissions and static electricity, addressing ergonomic concerns regarding
potential risks from extended computer monitor use.
Multiple Frequency Technology: Automatically adjusts monitor to the display
card’s scanning frequency, thus displaying the resolution required.
FullScan
™
Capability: Allows you to use the entire screen area in most resolu-
tions, significantly expanding image size.
OSM Display Screen Copyright 1997 by NEC Technologies, Inc.
78131861 5/21/98, 2:23 PM12
11
Troubleshooting
No picture
• Display card should be completely seated in its slot.
• Power Button and computer power switch should be in the ON position.
• Signal cable should be completely connected to display card/computer.
• Check connector for bent or pushed-in pins.
Image is scrolling or unstable
• Signal cable should be completely attached to the computer.
• Check pin assignments and signal timings of the monitor and your
display card with respect to recommended timings and pin assignments.
• If the Macintosh cable adapter is used, check for prior connection or
make sure the display card is Macintosh compatible and that the card is
properly seated in the computer.
LED on monitor is not lit
(no green, orange, yellow color can be seen)
• Power Switch should be in the ON position and power cord should
be connected.
Picture is fuzzy or color looks blotchy
• Adjust Brightness and Contrast Controls.
• Access the Degauss Control through OSM™ controls. Activate the
Degauss Control.
CAUTION: A minimum interval of 20 minutes should elapse before the
Deguass Control is used a second time when not switching
between modes.
Picture bounces or a wavy pattern is present
in the picture
• Move electrical devices that may be causing electrical interference away
from the monitor.
• See inside cover of User’s Manual for FCC information.
Edges of the display image are not square
• Use the OSM Geometry Controls to straighten the edges.
• If possible, position the front of the monitor facing east.
Display image is not centered, too small, or too large
• Use the OSM Size and Position Controls to adjust the image.
78131861 5/21/98, 2:23 PM13
12
References
• BBS (508) 635-4706
NEC Technologies’ Remote Bulletin Board System is an electronic service
accessible with your system and a modem. Communication parameters
are: 300/1200/2400/9600/14.4k/28.8k bps, no parity, 8-data bits,
1 stop bit
• Customer Service/
Technical Support (800) 632-4662
Fax (508) 635-4298
• Direct Sales (800) 374-8000
• Electronic Channels:
Internet e-mail: [email protected]
Internet ftp site: ftp.nectech.com
World Wide Web: http://www.nec.com
• FastFacts™ Information (800) 366-0476
INFORMATION DESCRIPTION DOCUMENT #
MultiSync
®
E500
™
monitor Detailed monitor information 157501
MultiSync
®
E700
™
monitor Detailed monitor information 174601
Glossary Definition of terms related 900203
to functions, features and
installation of the
MultiSync monitor
More Information Names and addresses of 900204
other groups involved in
standards and features of
the MultiSync monitor
Macintosh Connection Detailed information on 153006
connecting the MultiSync
monitor to a Macintosh
Healthy Work Environment Detailed information on 900108
setting up a healthy work
environment
• Literature & Sales Info (800) NEC-INFO [(800) 632-4636]
• MultiSync Fulfillment (800) 820-1230
[For software & accessories]
• TeleSales (800) 284-4484
78131861 5/21/98, 2:23 PM14
NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from
defects in material and workmanship and, subject to the conditions set forth below, agrees
to repair or replace any part of the enclosed unit which proves defective for a period of three
(3) years from the date of first consumer purchase. Spare parts are warranted for ninety
(90) days.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. This warranty is limited to the original purchaser of the Product and is not
transferable. This warranty covers only NECTECH-supplied components. Service required as
a result of third party components is not covered under this warranty.
Proof of Purchase will be required by NECTECH to substantiate date of purchase. Such proof
of purchase must be an original bill of sale or receipt containing name and address of seller,
purchaser, and the serial number of the product.
It shall be your obligation and expense to have the Product shipped, freight prepaid, or
delivered to the authorized reseller from whom it was purchased or other facility authorized
by NECTECH to render the services provided hereunder in either the original package or a
similar package affording an equal degree of protection. All Products returned to NECTECH
for service MUST have prior approval, which may be obtained by calling 1-800-632-4662.
The Product shall not have been previously altered, repaired, or serviced by anyone other
than a service facility authorized by NECTECH to render such service, the serial number
of the product shall not have been altered or removed. The Product shall not have been
subjected to accident, misuse, or abuse or operated contrary to the instructions contained
in the User’s Manual.
NECTECH SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,
OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NECTECH
PRODUCT OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF
ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE
LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
This Product is warranted in accordance with the terms of this limited warranty. Consumers
are cautioned that Product performance is affected by system configuration, software, the
application, customer data, and operator control of the system, among other factors. While
NECTECH Products are considered to be compatible with many systems, specific functional
implementation by the customers of the Product may vary. Therefore, suitability of a Product
for a specific purpose or application must be determined by consumer and is not warranted
by NECTECH.
For the name of your nearest authorized NECTECH service facility, contact NECTECH
at 1-800-632-4662.
Limited Warranty
13
78131861 5/21/98, 2:23 PM15
NEC Enterprise Series
Part No. 78131861
Printed in Malaysia
PROPRIETARY NOTICE AND LIABILITY DISCLAIMER
The information disclosed in this document, including all designs and related materials, is the valuable property of NEC
Technologies and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this
document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights
are expressly granted to others.
The NEC Technologies product(s) discussed in this document are warranted in accordance with the terms of the Limited
Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon
factors such as system configuration, customer data and operator control. Since implementation by customers of each
product may vary, the suitability of specific product configurations and applications must be determined by the customer
and is not warranted by NEC Technologies.
To allow for design and specification improvements, the information in this document is subject to change at any time
without notice. Reproduction of this document or portions thereof without prior approval of NEC Technologies is
prohibited.
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
U.S. Responsible Party: NEC Technologies, Inc.
Address: 1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143
Tel. No.: (630) 775-7900
Type of Product: Computer Monitor
Equipment Classification: Class B Peripheral
Models: JC-1575VMA and JC-1746UMA
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
MultiSync is a registered trademark of NEC Technologies, Inc. in the U.S. and of NEC Home Electronics, Ltd. in Canada, UK, Germany, France,
Spain, Italy, Austria, Benelux, Switzerland, Denmark, Finland, Norway and Saudi Arabia. AccuColor, OptiClear and ErgoDesign are
registered trademarks of NEC Technologies, Inc. in the U.S. and Canada. E500, E700, Reduced Magnetic Field, IPM, FastFacts, FullScan and
OSM are trademarks of NEC Technologies, Inc. in the U.S. NEC is a registered trademark of NEC Corporation Copyright 1997 by NEC
Technologies, Inc. OSM Display Screens Copyright 1997 by NEC Technologies, Inc. Windows is a registered trademark of Microsoft
Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners.
The Energy Star emblem does not represent EPA endorsement of any product or service.
78131861 5/21/98, 2:23 PM16
/
