SINGER SEQS-6000 User manual

Category
Sewing machines
Type
User manual

This manual is also suitable for

63
grey: Warm Gray 5cred: 199 C
INSTRUCTION MANUAL
F-1
F-2
“IMPORTANT SAFETY INSTRUCTIONS”
“WARNING
-
To reduce the risk of burns, re, electric shock, or injury to persons: ”
1. “Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.”
2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.”
3. Use this sewing machine only for its intended use as described in this manual. Use only attachments recommended by the
manufacturer as contained in this manual.”
4. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped
or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for
examination, repair, electrical or mechanical adjustment.”
5. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in
order to avoid a hazard.”
6. Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot
control free from the accumulation of lint, dust, and loose cloth.”
7. “Never drop or insert any object into any opening.”
8. Indoors use only.”
9. “Do not operate where aerosol (spray) products are being used or where oxygen is being administered.”
10. “To disconnect, turn switch to the off („0“) position, then remove plug from outlet.”
11. “ Switch off or unplug the appliance when leaving it unattended, unplug the appliance before carrying out maintenance or
replacing lamps.”
12. “Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.”
13. “Keep ngers away from all moving parts. Special care is required around the sewing machine needle.”
14. “Never sew with a damaged needle plate as this can cause needle to break.”
15. “Do not use bent needles.”
16. “Do not pull or push fabric while stitching. It may deect the needle causing it to break.”
17. Switch the sewing machine off (“0”) when making any adjustments in the needle area, such as threading needle, changing
needle, threading bobbin, or changing presser foot, etc.”
18. Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user
servicing adjustments mentioned in the instruction manual.”
19. To avoid electrical shock never put the machine nor the mains cable or mains plug into water or other liquids.”
20. The LED lamp maximum power is 0.3w, maximum voltage is DC 5v, if the LED lamp is damaged, you should not use the
product and send it to the manufacture or service agent to repair or replace at once.”
21. Attention the following to avoid injury:
- Unplug the foot controller of the appliance when leaving it unattended:
- Unplug the foot controller of the appliance before carrying out any maintenance.”
“SAVE THESE INSTRUCTIONS”
“This product is for household use, or equivalent.”
“When using an electrical appliance, basic safety precautions should always be followed, including the following.”
“Read all instructions before using this sewing machine.”
“DANGER
-
-
To reduce the risk of electric shock:”
1. This sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electric
outlet immediately after using and before cleaning.”
FOOT CONTROL (USA & Canada only)
Use Model YC-485 EC or Model JF-1000 with this sewing machine.
POLARIZED PLUGS CAUTION (USA & Canada only)
This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended
to t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a
qualied electrician to install the proper outlet. Do not modify the plug in any way.
“CAUTION
-
-
Moving parts-To reduce risk of injury, switch off before servicing. Close cover before operating
machine.”
This appliance complies with EEC Directive 2004/108/EC covering the electromagnetic compatibility.
Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation
relating to electrical/ electronic products. If in doubt please contact your retailer for guidance.
SINGER and FUTURA QUARTET are exclusive trademarks of The Singer Company Limited S.à r.l. or its Afliates.
©2011 The Singer Company Limited S.à r.l. or its Afliates. All rights reserved.
1
1. GETTING TO KNOW YOUR MACHINE
Machine identication ---------------------------------------------------2
Accessories ----------------------------------------------------------------3
Setting up your machine -----------------------------------------------4
Spool pins ------------------------------------------------------------------ 4
Winding bobbin -----------------------------------------------------------5
Threading the bobbin thread ------------------------------------------6
Threading the top thread -----------------------------------------------7
Using automatic needle threader ------------------------------- 8 - 9
Needle, thread and fabric chart ------------------------------------ 10
Adjusting top thread tension ---------------------------------------- 11
Changing presser foot ------------------------------------------------ 11
Control panel function ------------------------------------------ 12 - 13
Functions of operation switch panel ------------------------------- 14
2. STARTING TO SEW
Quick reference table of stitch length and width --------- 15 - 16
Straight stitching ------------------------------------------------- 17 - 18
Keeping seams straight, Inserting zippers and piping
Hand-look quilt stitch -------------------------------------------------- 18
Zigzag stitching --------------------------------------------------------- 19
Adjusting stitch width and length, Satin stitch
Placement of patterns
Blind stitch --------------------------------------------------------------- 20
Multi-stitch zigzag ------------------------------------------------------ 21
Stretch stitches --------------------------------------------------- 22 - 25
Straight stretch stitch, Ric-rac stitch,
Honeycomb stitch, Overedge stitch, Feather stitch,
Pin stitch, Ladder stitch, Blanket stitch (1), (2),
Slant pin stitch, Slant overedge stitch,
Greek key stitch, Entredeux stitch, Criss-cross stitch,
Crossed stitch
Decorative Stitching --------------------------------------------------- 25
Continuous patterns --------------------------------------------------- 26
Sewing on a button ---------------------------------------------------- 26
Buttonholes -------------------------------------------------------- 27 - 29
Using buttonhole foot, Procedure, Corded buttonholes
Buttonholing with hard-to-sew fabrics
TABLE OF CONTENTS
3. PREPARATION FOR EMBROIDERY SEWING
Before attaching embroidery unit ---------------------------- 30 - 31
Attaching embroidery foot, Inserting the bobbin,
Threading the top thread, Extension table,
Attaching embroidery unit -------------------------------------------- 32
Removing embroidery unit ------------------------------------------- 32
Securing fabric in embroidery hoop ------------------------------- 33
Using fabric and stabilizer ------------------------------------- 34 - 35
Preparing the machine before installing the hoop ------------- 36
Attaching and removing embroidery hoop ----------------------- 36
Installation of software ------------------------------------------ 37 - 38
Operation switches when embroidery unit is attached ---------- 39
Operation switches, Thread tension control
Troubleshooting -------------------------------------------------- 40 - 43
Helpful information for embroidering with Futura
Multi hoop ---------------------------------------------------------- 44 - 47
Helpful messages when embroidering --------------------------- 48
4. OTHER THINGS YOU SHOULD KNOW
Presser foot lifter ------------------------------------------------------- 49
Feed dog control ------------------------------------------------------- 49
Converting to free-arm sewing ------------------------------------- 49
Performance checklist ------------------------------------------------ 50
Cleaning hook area and feed dogs -------------------------------- 51
Oiling inside the face cover ------------------------------------------ 52
Special accessories --------------------------------------------- 53 - 58
Helpful messages ------------------------------------------------ 59 - 60
Sewing machine
Dimensions: 567 mm × 240 mm × 317 mm
Mass of the equipment: 10.8 kg
Embroidery unit
Dimensions: 504 mm × 411 mm × 141 mm
Mass of the equipment: 3.0 kg
Rated Voltage: 230 V ~
Rated Frequency: 50 Hz
Rated input: 64 W
Using ambient temperature: Normal temperature
Acoustic noise level: less than 70 db(A)
For European version
2
1. Pre-tension guide
2. Bobbin winding tension disk
3. Thread tension control
4. Threading lever
5. Face cover
6. Thread cutter/holder
7. Extension table (Accessory box)
8. Bobbin winder spindle
9. Bobbin winder latch
10. Operation buttons
11. Horizontal spool pin
12. Handle
13. Hand wheel
14. Power/light switch
15. Cord socket
16. Buttonhole lever
17. Feed dog control
18. Presser foot lifter
19. Identication plate
20. Thread guide
21. Twin thread guide
22. Presser foot screw
23. Needle
24. Bobbin cover plate
25. Needle bar
26. Alternate thread cutter
27. Foot release button
28. Needle clamp screw
29. General purpose foot
30. Feed dogs
31. Needle plate
32. Bobbin cover release button
33. Embroidery unit
34 Hoop release lever
35. Carriage
36. Handle
37. Accessory drawer
38. Hoop bracket
39. Release lever
40. Connector
41. Large hoop
42. Inner frame
43. Outer frame
44. Hoop adjusting screw
45. Hoop mounting plate
46. Small hoop
47. Power line cord
48. Foot control
49. USB cable
50. Instruction manual
NOTE: Be sure the USB cable is
attached to your machine when
doing embroidery.
1. GETTING TO KNOW YOUR MACHINE
MACHINE IDENTIFICATION
34
3837 39
4036 35
47
48 50
33
46
43
42
44
45
49
43
42
44
45
41
12
11
13
14
15
16
17
18
19
3
2 1
4
5
6
7
8
9
10
20
21
22
23
24
26
27
28
29
31
32
30
25
3
ACCESSORIES
FOR SEWING MACHINE
1. Needles
2. Bobbins
3. Auxiliary spool pin
4. Spool pin felt discs
5. Spool pin cap (mini)
6. Spool pin cap (small)
7. Spool pin cap (large)
8. Buttonhole opener/Brush
9. Screwdriver for needle plate
10. Screwdriver (large)
11. Screwdriver (small)
12. Zipper foot
13. Blind hem foot
14. Satin foot
15. Button sewing foot
16. Buttonhole foot and underplate
17. Thread spool net (long)
18. Thread spool net (short)
FOR EMBROIDERY
19. Vinyl bag
20. Bobbins
21. Scissors
22. Embroidery presser foot
23. Embroidery software CD
FUTURA embroidery is a “system” in which your
computer software communicates designs to your
embroidery machine. The FUTURA embroidery
designs are accessed via your computer by installing
the FUTURA software.
To install the FUTURA software, refer to the CD insert
for more information.
9 10 11
12
13
14 15
16 17 18
23
19
20
21
22
The Foot that comes on your
Sewing machine is called the
General Purpose Foot and will
be used for the majority of your
sewing.
The Satin Foot (14) is another
very useful foot and should be
used for most decorative sewing.
When purchasing additional
bobbins, be sure they are Class
I5 J.
1 2 5 6
7 8
3 4
4
XL-550-P04-1.eps
Pin
1
3
2
SETTING UP YOUR MACHINE
Be sure to wipe off any surplus oil from needle plate area
before using your machine the rst time.
POWER LINE CORD/FOOT CONTROL
Connect the plug of the power line cord into the cord
socket (1) and your wall outlet (2) as illustrated.
Connect the foot control plug into the machine socket (3),
when using sewing machine only.
NOTE: In sewing mode, the machine can be operated
either with or without the foot control (see page
14).
POWER/LIGHT SWITCH
Your machine will not operate until the power/light switch
is turned on. The same switch controls both the power and
the light.
When servicing the machine, or when changing needles
or lights, etc., the machine must be disconnected from the
power supply.
Always disconnect the machine from power
supply by removing the plug from the wall-
outlet.
SPOOL PINS
HORIZONTAL SPOOL PIN for normal
thread spool
Place thread spool on the pin and secure with a spool cap
to ensure smooth ow of thread.
VERTICAL SPOOL PIN for large thread
spool
Attach the spool pin. Place felt disc over it. Place a thread
spool on the spool pin.
Set power/light switch at “OFF”
Machine socket
Power line cord
Foot control
Power/light switch “OFF” Power/light switch “ON”
Spool Spool pin
Felt disc
Vertical spool pin
Spool
Thread retaining slit
Spool pin cap
5
WINDING BOBBIN
1. Place a spool of thread on the spool pin, and secure it with
the spool pin cap. Pull the thread out from the spool and
place it through thread guides as shown in illustration.
2. Put end of thread through the hole in bobbin as shown.
Place bobbin onto the bobbin winder spindle as far as it
can go.
3. Holding onto the end of the thread, push the bobbin winder
latch against the bobbin until it clicks and bobbin starts to
rotate.
4. Bobbin will disengage automatically and the winding
mechanism will stop when the bobbin is full. Remove the
wound bobbin and cut the thread tail.
Be sure to use Class 15 J bobbins.
1
2
3
4
6
AB
THREADING THE BOBBIN THREAD
1. Raise the needle to its highest position by rotating the hand
wheel counter clockwise (toward you).
2. Remove the bobbin cover plate by pushing the release
button to the right. Bobbin cover will pop up sufciently to
allow you to remove the cover.
3. Insert the bobbin making sure the bobbin rotates counter-
clockwise when you pull the thread.
4. Pull thread through the slot (A) and then to the left.
5. With a finger held gently on top of the bobbin, pull the
thread until it stops in the slot (B). Then pull the thread
along the groove on the needle plate until it is snipped with
cutter on the top left.
6. Replace the clear bobbin cover plate onto the needle plate.
NOTE: Sewing can be started without having to pull
up the bobbin thread.
NOTE: This is a very important step. The bobbin
must rotate counterclockwise when thread is pulled.
Groove
A
Cutter
7
THREADING THE TOP THREAD
A. Raise the presser foot lifter. Always be sure to raise the
presser foot lifter before threading the top thread. (If the
presser foot lifter is not raised, correct thread tension
cannot be obtained.)
B. Turn the hand wheel counter clockwise (toward you) until
the needle is in its highest position.
C. Thread the machine with your left hand while rmly gripping
the thread with your right hand in the following order as
illustrated.
* Guide the thread through thread guides (1 & 2), and then
pull it down along the groove (3).
* Guide the thread into the thread guide (4).
* Pass the thread through the eye of the needle (5) from
front to back. (See following page for instructions on
operation of the Automatic Needle Threader.)
IMPORTANT:
To verify that the machine is threaded properly in the
tension discs, do this simple check:
1.) With the presser foot raised, pull the thread towards
the back of the machine. You should detect only
a slight resistance and little or no deection of the
needle.
2.) Now lower the presser foot and again pull the thread
towards the the back of the machine. This time you
should detect a considerable amount of resistance
and much more deflection of the needle. If you do
not detect the resistance you have mis-threaded the
machine and need to re-thread it.
8
1. Thread the machine with your left hand while gripping the
thread with your right hand. Hook thread to the thread
guide on the needle bar and pull it toward you leaving
about 4” (10 cm) clear.
2. Hook thread into the twin thread guides (A and B).
3. Pull thread gently into the thread cutter/holder to cut and
hold it in place.
4. Pull down the threading lever to its lowest position until the
twin thread guide rotates and stops.
5. Release the threading lever and needle will be threaded
automatically. If it should not return to the original position,
raise it gently by hand.
6. Pull thread loop away from you.
USING AUTOMATIC NEEDLE THREADER
Be sure to raise the presser foot lifter and raise the needle
to its highest position before threading.
Don’t pull thread with strong force or thread may
be pulled off from needle hole after threading.
Make sure that the guide doesn’t touch fabric, etc.
If the needle has not been threaded correctly, re-
thread from STEP 1.
IMPORTANT: If the needle cannot be threaded with the
Automatic Needle Threader due to particular qualities
of the thread, or if the thread is too thick for the
needle being used, then manually thread the needle
after hooking the thread through the thread guide on
the needle bar.
NOTE:
For smooth threading, it is recommended that
the machine be set for straight stitch (in center
needle position) when using the automatic needle
threader.
Heavy thread cannot be threaded through fine
needle.
Don’t lower the threading lever while the machine is
in operation or the threading hook may be broken.
3
Thread cutter/holder
2
Twin thread guide
B
A
1
Threading hook
Thread guide
4
Threading lever
9
6
5
If the threading hook is deviated from needle hole,
adjust the position of the hook using a small screw
driver.
If the threading hook cannot catch thread, adjust
the vertical position by bending the twin thread
guide.
HELPFUL SUGGESTIONS:
Put a drop of sewing machine oil onto the felt disc,
if the machine is used after a long interval.
Felt disc
10
Changing the needle
1. Raise the needle bar to its highest position by turning the
hand wheel counter clockwise (toward you).
2. Loosen the needle clamp screw by turning it toward you.
3. Remove the needle by pulling it downward.
4. Insert the new needle into the needle clamp with the at
side toward the back.
5. Push the needle up as far as it can go.
6. Tighten the needle clamp screw firmly with the screw
driver.
Always disconnect the machine from power
supply by removing the plug from the wall-outlet.
* For best sewing results, always use a Singer Branded Needle.
FABRICS THREAD NEEDLES
The fabrics below can be of any
ber: cotton, linen, silk, wool,
synthetic, rayon, blends. They
are listed as examples of weight.
Light-
Weight
Batiste
Chiffon
Crepe
Medium-
Weight
Corduroy
Flannel
Gabardine
Gingham
Linen
Muslin
Wool Crepe
Medium-
Heavy
Bonded Wovens
Canvas
Coating
Denim
Duck
Sailcloth
Knits Bonded Knits
Double Knit
Jersey
Tricot
Cotton-wrapped
Polyester
100% Polyester
* Mercerized Size 40
* "Heavy Duty"
Cotton-wrapped
Polyester
100% Polyester
* Mercerized Size 60
Cotton-wrapped
Polyester
100% Polyester
* Mercerized Size 50
Nylon
Cotton-wrapped
Polyester
Polyester
Nylon
2000 or 2020
red
shank
2000 or 2020
red
shank
2000 or 2020
red
shank
2001 or 2045
yellow
shank
11/80
orange
band
14/90
blue
band
16/100
purple
band
18/110
yellow
band
TYPE SIZE
11/80
orange
band
14/90
blue
band
16/100
purple
band
NEEDLE, THREAD AND FABRIC CHART
Your fabric will determine the choice of a needle and thread.
The following table is a practical guide to needle and thread
selection. Always refer to it before a new sewing project.
Generally, the same size and type of thread is used in the
bobbin as in the upper thread.
Flat
side
toward
the
back
Flat side
Pin
Needle
11
CHANGING PRESSER FOOT
Be sure the needle is in the highest position. Raise presser
foot lifter.
1. Push presser foot release button to remove the foot.
2. Place the desired foot on the needle plate aligning the
presser foot pin with the foot holder.
3. Lower the presser foot lifter so that the foot holder snaps
on the foot.
1
3
2
ADJUSTING TOP THREAD TENSION
90% of your sewing will be accomplished with the word “S”
exposed on the tension control dial on top of the machine.
STRAIGHT STITCHING
The correct appearance of your stitching is largely determined
by the balanced tension of both top and bobbin threads. The
tension is well balanced when these two threads ‘lock’ in the
middle of layers of the fabric you are sewing.
If, when you start to sew, you nd that the stitching is irregular,
you will need to adjust the tension control. Do this, however,
only after you have determined that the machine is correctly
threaded (see page 7).
Make all adjustments with presser foot ‘down’.
A balanced tension (identical stitches both top and bottom) is
usually only desirable for straight stitch sewing.
ZIGZAG, SATIN STITCH, DECORATIVE and
BUTTON HOLE SEWING
For zigzag sewing, satin stitch and decorative stitch functions,
thread tension should be less than that for straight stitch
sewing.
It is recommended for buttonholes to set thread tension at E.
You will always obtain a nicer stitch and less puckering when
the upper thread appears slightly on the bottom side of your
fabric.
BOBBIN TENSION
The bobbin tension has been correctly set at the factory,
so you do not need to adjust it.
Helpful Hint: A slight adjustment to a higher number or a
lower number may improve sewing appearance.
Under side
Decrease tension Increase tension
Top side
Well balanced
Top stitch too tight Top stitch too loose
Foot release button
Presser foot lifter
Foot holder
12
CONTROL PANEL FUNCTIONS
Pattern selection buttons
Turn on the power switch and the LED indicator above the straight
stitch pattern will be lit. At this point you may sew Straight Stitch.
To select other patterns, push the pattern selection button to
the right of the row that contains your desired pattern. Stop
when the LED indicator above your pattern is lit.
Twin needle mode button
*NOTE: The provided scales and numbers on the length and width controls are for reference only
and do not represent actual sewing parameters of length and width.
LED indicator
LED indicator
Stitch length control
Pattern selection buttons
Stitch width/needle position control
13
Stitch length and width/needle position controls
*Auto/Default settings
Your sewing machine will produce most of your stitching
requirements at an Auto/Default Stitch Length and Width. When
a pattern is selected, it will automatically sew at default settings of
stitch length, width and needle position for straight stitch.
Auto (preprogrammed) default settings are easily determined
by moving the Stitch Length and Width / Needle Position
Control Knob. The LED Indicator next to the Control will light
in orange without blinking and a beep will sound indicating you
are at the Auto / Default Position.
*Manual settings
Once you have determined the Auto / Default position you can
manually change the length, width or straight stitch needle
postition according to your preference. Starting at the Auto
position, slide the control knob left or right to locate each of
the potential adjustments. At each manual adjustment point,
the LED will blink 3 times in green and a beep will sound.
The LED will light in red beyond the potential adjustment range.
NOTES: 1. Some patterns offer more opportunities for
manual adjustments than others.
2. An alternate method of determining
available adjustments is to move the
control knobs while sewing slowly.
Twin needle mode button
The width setting for twin needle sewing can be activated if it is
available for the selected pattern. The LED turns on when twin
needle sewing is activated.
Width setting for twin needle sewing can be activated, if it
is available for a selected pattern. LED turns on when twin
needle sewing is activated.
14
Reverse stitch function
for straight and zigzag
stitches
Tacking stitch function
for tie-off of other
stitches
1
2
3
4
5
FUNCTIONS OF OPERATION SWITCH
PANEL
1. TACKING STITCH MODE BUTTON
Push this button and tacking stitch can be done with LED lit.
The sewing machine makes 4 tiny tacking stitches to tie off
the sewing on all patterns. The position of the tacking stitches
will be at the exact spot in the pattern where the tacking stitch
button is pushed.
2. NEEDLE STOP POSITION SELECTOR BUTTON
When the machine is turned on, needle is set at its up-stop
position with upper LED lamp lit. When the button is pushed,
needle is set at its down-stop position with lower LED lamp
lit. Push it again and it will return to its up-stop position with
upper LED lamp lit.
3. REVERSE STITCH BUTTON
Reverse sewing is carried out by pushing the reverse stitch
button. The machine will sew 4 stitches in reverse and stop.
4. START/STOP BUTTON
When the Start/Stop button is pushed, the machine starts
slowly, and when the button is pushed once more, the
machine stops.
However, when foot control is plugged, the Start/Stop button
will be inactive.
5.
LED INDICATOR
Green light indicates machine is ready to start.
Red light indicates machine is operating.
Flashing red light indicates a problem or an error.
* Flashing for 2 - 3 seconds shows that an incorrect
operation was made.
* Continuous flashing indicates that the machine
malfunctions.
6. SPEED CONTROL LEVER
Sliding the lever sets desired sewing speed. When foot control
is used, the lever serves as a top speed limiter.
6
15
2. STARTING TO SEW
QUICK REFERENCE TABLE OF STITCH LENGTH AND WIDTH
Adjusting needle position for straight stitch
13 needle positions are available for quilting, topstitching, etc.
Width control
Toward rightToward left
Toward rightToward left
STITCH SYMBOL
LENGTH NEEDLE POSITION
AUTO MANUAL AUTO MANUAL
STRAIGHT 2.5 0.5 ~ 4.8
CENTER LEFT - RIGHT
STRAIGHT STRETCH 2.5 1.5 ~ 3.0
HAND-LOOK QUILT 2.5 2.0 ~ 4.0
-
STITCH SYMBOL
LENGTH WIDTH
AUTO MANUAL AUTO MANUAL
REGULAR BLINDHEM 2.0 1.0 ~ 3.0 3.0 1.0 ~ 6.0
STRETCH BLINDHEM 2.0 1.0 ~ 3.0 3.0 2.0 ~ 7.0
CRESCENT 0.5 0.5 ~ 1.5 7.0 3.5 ~ 7.0
ZIGZAG 2.0 0.5 ~ 3.0 5.0 0 ~ 7.0
RIC-RAC 2.5 1.5 ~ 3.0 5.0 2.0 ~ 7.0
MULTI-STITCH ZIGZAG 1.5 0.3 ~ 2.5 6.0 2.5 ~ 7.0
HONEYCOMB 2.0 1.5 ~ 3.0 6.0 3.0 ~ 6.0
16
STITCH SYMBOL
LENGTH WIDTH
AUTO MANUAL AUTO MANUAL
OVEREDGE
2.5 1.5
-
3.0 3.5 3.5
-
7.0
PYRAMID
0.5 0.5
-
1.5 7.0 3.5
-
7.0
FEATHER
2.0 1.0
-
3.0 6.0 3.0
-
6.0
PIN
2.5 1.5
-
3.0 3.0 1.0
-
7.0
LADDER
2.5 1.5
-
3.0 3.5 1.0
-
7.0
STAR
3.0
-
5.0 5.0, 6.0
VINE
2.0 1.5
-
2.5 7.0 3.5, 7.0
SERPENTINE
1.8 0.8
-
2.5 7.0 3.5, 7.0
BLANKET (1)
2.5 1.5
-
3.0 3.5 1.0
-
7.0
SLANT PIN
2.0 0.8
-
2.5 3.5 1.0
-
6.0
SLANT OVEREDGE
2.0 1.0
-
3.0 5.0 1.0
-
7.0
GREEK KEY
2.5 1.3
-
2.5 5.0 3.5
-
7.0
ENTREDEUX
2.5 1.5
-
3.0 3.0 2.0
-
7.0
ARROWHEAD
0.5 0.5
-
1.5 7.0 3.5
-
7.0
BLANKET (2)
2.5 1.5
-
3.0 3.5 1.0
-
7.0
CRISS-CROSS
2.0 1.5
-
3.0 6.0 3.0
-
6.0
CROSSED
2.5 1.0
-
3.0 4.0 2.0
-
6.0
BUTTON SEWING
0
-
3.0 2.0
-
4.5
WIDE BARTACK BUTTONHOLE
0.5 0.5, 0.8 5.5
-
NARROW BARTACK BUTTONHOLE
0.5 0.5, 0.8 3.5
-
17
A
B
C
D
E
F
G
J
1
H
I
STRAIGHT STITCHING
Straight stitch is most frequently used for all types of sewing.
Let’s begin by following the steps below.
1. SETTINGS
Presser foot - General Purpose Foot
Thread tension control - S
A. Thread tension control
B. Tacking stitch mode button
C. Needle up/down position selector button
D. Reverse stitch button
E. Start/stop button
F. Feed dog control (at rear side)
G. Presser foot lifter
H. Stitch length control
I. Stitch width control
J. Power/light switch
2. Pull both threads under the presser foot toward the back of
the machine, leaving about 6” (15 cm) clear.
3. Place the fabric under the presser foot and lower the
presser foot lifter.
4. Turn the hand wheel counter clockwise (towards you) until
the needle enters the fabric.
5. Start the machine. Guide the fabric gently with your hands.
When reaching the edge of the fabric, stop the sewing
machine.
6. First turn the handwheel counter clockwise (toward you)
until the needle is in its highest position, then raise the
presser foot. Draw the fabric to the rear and cut off excess
thread with the thread cutter located on the bottom of the
face cover, as shown.
KEEPING SEAMS STRAIGHT
To keep the seam straight, use one of the numbered guide
lines on the needle plate. The numbers indicate distance from
the needle at its center position.
The guide line on the bobbin cover plate is a ¼” (6mm) seam
guide line, used for piecing quilt blocks or for sewing narrow
seams.
3/4" (19
mm
)
5/8" (16
mm
)
1/2" (13
mm
)
3/8" ( 9
mm
)
1/4" ( 6
mm
)
NOTE: Based upon the weight of the fabric, slight
“ne tuning” of the tension may be desired.
NOTE: Since a straight stitch has no width, the
stitch width control is used to change the needle
position.
NOTE: The Needle Plate has both Metric and Inch
Markings as an aid for guiding your fabric when
sewing a seam.
2
3
6
5
4
18
INSERTING ZIPPERS AND PIPING
Use the zipper foot to sew to the right or left of the zipper or to
sew close to a cord.
INSERTING ZIPPERS
To sew down the right side, attach left side of zipper foot to
presser foot holder so that the needle passes through the
opening on the left side of the foot.
To sew down the left side, attach right side of foot to foot
holder.
PIPING
Create a piping by covering a ller cord with a bias strip of fabric.
Attach the right side of the zipper foot to the foot holder so that
the needle passes through the right side of the zipper foot.
Baste the seam allowances together, enclosing the ller cord,
forming seam tape for the piping.
Helpful Hint: Slight adjusting of the needle position to
sew closer to the piping may be accomplished with
the Stitch Width Control.
HAND-LOOK QUILT STITCH
This stitch is designed to look like hand sewing for topstitching
and quilting.
1. Thread bobbin with desired top stitching color.
2. Thread the needle with either invisible thread or with thread
that is a color which blends in with the fabric color, so it
doesn’t show.
3. Increase thread tension toward 6 or higher until you
achieve the desired appearance.
4. Set the stitich length at 4 (maximum).
5. Start to sew.
Needle to left of foot Needle to right of foot
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

SINGER SEQS-6000 User manual

Category
Sewing machines
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI