Genesis Advanced Technologies GBG800L User manual

8" Bench Grinder with Lights

Meuleuse d'établi de 8 po, avec éclairages

Esmeriladora de banco de 8”, con luces

Operator's Manual

Manuel d’utilisation

Manual del Operario

GBG800L

English

8" Bench Grinder with Lights

Operator’s Manual GBG800L

8" BENCH GRINDER WITH LIGHTS 3/4 HP

Operator’s Manual

Speciﬁcations:

• Model:  GBG800L

• RatedVoltage: 120VAC,60HZ

• RatedInputPower: 3/4HP

• NoLoadSpeed: 3550RPM

• WheelSize:  8”

• ShaftDiameter: 3/4”

Includes:(1)36GWheel,(1)60GWheelandLightBulbs

 WARNING:To reduce the risk of injury, user must read and understand

this operator’s manual before operating this tool. Save this Manual for future

reference.

Toll-Free Help Line: 1-888-552-8665

WARNING:TheOperationofanypowertoolcanresultinforeign

objectsbeingthrownintoyoureyes,whichcanresultinsevereeyedamage.

Beforebeginningtooloperation,alwayswearsafetygogglesorsafetyglasses

withsideshieldsandafullfaceshieldwhenneeded.WerecommendWide

VisionSafetyMaskforuseovereyeglassesorstandardsafetyglasseswith

sideshields.AlwaysweareyeprotectionwhichismarkedtocomplywithANSI

Z87.1.

Look for this symbol to point out important safety

precautions. It means attention!!! Your safety is

involved.

GENERAL SAFETY RULES

 WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

• Leadfromlead-basedpaints,

• Crystallinesilicafrombricksandcementandothermasonryproducts,and

• Arsenicandchromiumfromchemicallytreatedlumber.

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to ﬁlter out microscopic particles.



WEARYOUR

FORESIGHTISBETTER

THANNOSIGHT

SAFETYGLASSES

English

 WARNING:READ AND UNDERSTAND ALL WARNINGS, CAUTIONS

AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure

to follow all instructions listed below may result in electric shock, ﬁre and/or

serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA SAFETY

•

Keep your work area clean and well lit.Clutteredbenchesanddarkareasinvite

accidents.

•

Do not operate power tools in explosive atmospheres,suchasinthe

presenceofammableliquids,gases,ordust.Powertoolscreatesparkswhichmayignitethedust

orfumes.

• Keep bystanders, children, and visitors away while operating a power

tool.Distractionscancauseyoutolosecontrol.

ELECTRICAL SAFETY

•

Power tool plugs must match the outlet. Nevermodifythepluginanyway.Donot

useanyadapterplugsinanyearthed(grounded)powertools.Doubleinsulatedtoolsareequipped

withapolarizedplug(onebladeiswiderthantheother).Thisplugwilltinapolarizedoutletonly

oneway.Iftheplugdoesnottfullyintheoutlet,reversetheplug.Ifitstilldoesnott,contact

aqualiedelectriciantoinstallapolarizedoutlet.Donotchangethepluginanyway.Double

insulationeliminatestheneedforthethreewiregroundedpowercordandgroundedpowersupply

system.

•Donotexposepowertoolstorainorwetconditions.Waterenteringapower

toolwillincreasetheriskofelectricshock.

•Avoidbodycontactwithearthedorgroundedsurfacessuchaspipes,

radiators, ranges and refrigerators. Thereisanincreasedriskofelectricshockif

yourbodyisgrounded.

•Donotabusethecord.Neverusethecordforcarrying,pullingorunpluggingthepower

tool.Keepcordawayfromheat,oil,sharpedgesormovingparts.Damagedcordsincreasetherisk

ofelectricshock.

•Whenoperatingapowertooloutside,useanextensioncordsuitable

for outdoor use. Thesecordsareratedforoutdooruseandreducetheriskofelectricshock.

•DonotuseAConlyratedtoolswithaDCpowersupply.Whilethetoolmay

appeartowork.TheelectricalcomponentsoftheACratedtoolarelikelytofailandrateahazardto

theoperator.

PERSONAL SAFETY

•

Stay alert, watchwhatyouaredoingandusecommonsensewhenoperatingapowertool.

Donotusetoolwhiletiredorundertheinuenceofdrugs,alcohol,ormedication.Amomentof

inattentionwhileoperatingpowertoolsmayresultinseriouspersonalinjury.

•Usesafetyequipment.Alwaysweareyeprotection.Safetyequipmentsuchasdust

mask,non-skidsafetyshoes,hardhat,orhearingprotectionforappropriateconditionswillreduce

personalinjuries.

•Dressproperly.Donotwearlooseclothingorjewelry.Keepyourhair,clothingandgloves

awayfrommovingparts.Looseclothes,jewelryorlonghaircanbecaughtinmovingparts.Air

ventsmaycovermovingpartsandshouldbeavoided.

English

8" Bench Grinder with Lights

Operator’s Manual GBG800L

•Avoidaccidentalstarting.Ensuretheswitchisintheoffpositionbeforepluggingin.

Carryingpowertoolswithyourngerontheswitchorplugginginpowertoolsthathavetheswitch

oninvitesaccidents.

•Removeanyadjustingkeysorwrenchesbeforeturningthepower

tool on. Awrenchorkeythatisleftattachedtoarotatingpartofthetoolmayresultinpersonal

injury.

•Donotoverreach.Maintainproperfootingandbalanceatalltimes.Lossofbalancecan

causeaninjuryinanunexpectedsituation.

•Ifdevicesareprovidedforconnectionofdustextractionand

collection facilities, ensure these are connected and properly used.

Useofthesedevicescanreducedustrelatedhazards.

•Donotusealadderorunstablesupport.Stablefootingonasolidsurfaceenables

bettercontrolofthetoolinunexpectedsituations.

•Keeptoolhandlesdry,cleanandfreefromoilandgrease.Slipperyhandles

cannotsafelycontrolthetool.

TOOL USE AND CARE

•

Secure the work piece. Useclamporotherpracticalwaytoholdtheworkpiecetoa

stableplatform.Holdingtheworkpiecebyhandoragainstyourbodyisunstableandmayleadto

lossofcontrol.

•Donotforcethepowertool.Thetoolwillperformthejobbetterandsaferatthefeed

rateforwhichitisdesigned.Forcingthetoolcouldpossiblydamagethetoolandmayresultin

personalinjury.

•Usethecorrectpowertoolforthejob.Don’tforcethetoolorattachmenttodoa

jobforwhichitisnotdesigned.

•Donotuseatooliftheswitchdoesnotturnitonoroff.Anytoolthat

cannotbecontrolledwiththeswitchisdangerousandmustberepairedorreplacedbyan

authorizedservicecenter.

•Turnthepowertooloff,anddisconnecttheplugfromthepowersourceand/

orbatterypackfromthepowertoolbeforemakinganyadjustments,changingtheaccessories,or

storingthetools. Suchpreventivesafetymeasuresreducetheriskofanaccidentalstartupwhich

maycausepersonalinjury.

•Storeidletooloutofreachofchildrenandotherinexperienced

persons. Itisdangerousinthehandofuntrainedusers.

•Maintainpowertoolswithcare.Checkforproperalignmentandbindingofmoving

parts,components,andanyotherconditionsthatmayaffectthetool’soperation.Aguardorany

otherpartthatisdamagedmustbeproperlyrepairedorreplacedbyanauthorizedservicecenterto

avoidriskofpersonalinjury.

•Userecommendedaccessories.Usingaccessoriesandattachmentsnot

recommendedbythemanufacturerorintendedforuseonthistypetoolmaycausedamageto

thetoolorresultinpersonalinjurytotheuser.Consulttheoperator’smanualforrecommended

accessories.

•Keepcuttingtoolssharpandclean.Properlymaintainedcuttingtoolswithsharp

cuttingedgesarelesslikelytobindandareeasiertocontrol.

English

•Feedtheworkpieceinthecorrectdirectionandspeed.Feedthework

pieceintoablade,cutter,orabrasivesurfaceagainstthedirectionofthecuttingtool’sdirection

ofrotationonly.Incorrectlyfeedingtheworkpieceinthesamedirectionmaycausethework

piecetobethrownoutathighspeed.

•Neverleavethetoolrunningunattended,turnthepoweroff.Donot

leavethetooluntilitcomestoacompletestop.

•Neverstartthepowertoolwhenanyrotatingcomponentisin

contact with the work piece.

SERVICE

•

Have Your Power Tool Serviced by a qualiﬁed repair person using

only identical replacement parts. Thiswillensurethatthesafetyofthepowertool

ismaintained.

•ServiceYourPowerToolperiodically.Whencleaningatool,becarefulnotto

disassembleanyportionofthetoolsinceinternalwiresmaybemisplacedorpinched.

WARNING:

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING

INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all

instructions listed below may result in electric shock, ﬁre and/or serious

personal injury.

EXTENSION CORDS

Grounded tools require a three wire extension cord.Doubleinsulatedtoolscan

useeitheratwoorthreewireextensioncord.Asthedistancefromthepowersupplyoutletincreases,

youmustuseaheaviergaugeextensioncord.Usingextensioncordswithinadequatelysizedwire

causesaseriousdropinvoltage,resultinginlossofpowerandpossibletooldamage.Refertothe

tableshownbelowtodeterminetherequiredminimumwiresize.

Thesmallerthegaugenumberofthewire,thegreaterthecapacityofthecord.Forexample:a

14-gaugecordcancarryahighercurrentthana16-gaugecord.Whenusingmorethanoneextension

cordtomakeupthetotallength,besureeachcordcontainsatleasttheminimumwiresizerequired.

Ifyouareusingoneextensioncordformorethanonetool,addthenameplateamperesandusethe

sumtodeterminetherequiredminimumwiresize.

Guidelines for Using Extension Cords

• Ifyouareusinganextensioncordoutdoors,besureitismarkedwiththesufx“W-A”(“W”in

Canada)toindicatethatitisacceptableforoutdooruse.

• Besureyourextensioncordisproperlywiredandingoodelectricalcondition.Alwaysreplacea

damagedextensioncordorhaveitrepairedbyaqualiedpersonbeforeusingit.

• Protectyourextensioncordsfromsharpobjects,excessiveheat,anddamporwetareas.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate

Amperes

(At Full Load)

Extension Cord Length

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 200 Feet

0–2.0 18 18 18 18 16 16

2.1–3.4 18 18 18 16 14 14

3.5–5.0 18 18 16 14 12 12

5.1–7.0 18 16 14 12 12 10

7.1–12.0 18 14 12 10 8 8

12.1–16.0 14 12 10 10 8 6

16.1–20.0 12 10 8 8 6 6

English

8" Bench Grinder with Lights

Operator’s Manual GBG800L

SPECIFIC SAFETY RULES FOR BENCH GRINDERS

 WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT

(GAINED FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT

SAFETY RULES. If you use this tool unsafely or incorrectly, you can suffer

serious personal injury!

•Makesurethebenchgrinderisonarm,levelsurfaceandproperly

secured toavoidinjuryfromunexpectedmovement.Firmlyclamporboltthebenchgrinder

toasupportsurfacetopreventslippingorslidingduringtheoperation.

• Unplug the tool before making adjustments, repairs, maintenance

or storing.

•Alwaysswitchoffthetoolbeforeunpluggingittoavoidaccidentalstarting

whenrepluggingthetoolintoapowersource.

•Weareyeprotection.Donotweargloves,necktie,orlooseclothing.

•Donotoperatethebenchgrinderuntilitisassembledandinstalledaccordingto

thismanual’sinstructions.

•Alwaysmakesurethewheelguardsandeyeshieldsareinplace,properly

adjustedandsecuredinplace.

•Useonlyattachmentsratedfor3600RPMorhigherwitha1/2"arborhole

orappropriatesizedbushing.Neveruseanattachmentratedlowerthan3600RPMorattemptto

machineanundersizedwheeltotthearbor.

•Alwaysusethewheelangesfurnishedwiththistooltomountgrinding

wheelsonthegrindershafts.

•Donotovertightenthewheelnut.Excessivetighteningcancausethewheelto

crackpriortoorduringoperation.

•Inspectgrindingwheelsbeforestartingthemachineforvisibledefects

suchasssures,cracksorchips.Replacedamagedgrindingwheelsimmediately.

•Keepthesparkguardsclosetothewheelandreadjustthemasthe

wheel wears.

•Adjusttoolrestdistancefromthegrindingwheeltomaintainaseparation

of1/8"orlessasthewheeldiameterdecreasesfromuse.

•Donotuseagrindingwheelthatvibrateswhenused.Ifdressingthe

wheeldoesnotsolvethevibration,replaceit.Alsoinspectthemachineforothercausesof

vibrationsuchaswornbearingsorbentshaft.Repairorreplacebrokencomponentsimmediately

beforereusingthemachine.

•Donotusethemachineiftheswitchdoesnotturnitonandoff.Defectiveswitches

shouldbeimmediatelyreplacedbyanauthorizedservicecenterandthemachinenotusedunder

repairsarecompleted.

•Donotrapidlyturnthemachineonandoff.Thisactioncancausethewheelto

loosenandcreateapossiblehazard.

English

•Donotstanddirectlyinfrontofthemachinewhenturningit"ON".

Alwaysstandofftothesideofthemachineanddonotallowanypartofyourbodytobeinline

withthepathofthewheel.

•Nevergrindonacoldwheel.Thegrindershouldalwaysbestartedandallowedto

runatidlespeedforonfullminutebeforeapplyingworktothegrindingwheel.

•Nevergrindonthesideofthewheel.Alwaysgrindonthefaceofthewheelonly.

•Neverapplycoolantdirectlytothegrindingwheel.Coolantmayweaken

thebondingstrengthofthewheelcausingittofail.Dipthehotworkpieceintowatertocoolit.

•Neverstartthegrinderwiththeworkpiecepressedagainstthegrindingwheelor

otherattachments(wirebrushes,bufngwheels,etc.)

•Alwayseasetheworkpieceagainstthewheelwhenstartingtogrind.Use

lightpressurewhenapplyingtheworkpiecetothegrindingwheel.Excessivepressurecan

causethewheeltocrackoroverloadthemotor.

•Avoidawkwardoperationsandhandpositionswhereanunexpectedor

suddenslipthatcouldcauseyourhandorngerstomoveintothegrindingwheel,wirebrush,

bufngwheel,etc.

•Alwayskeephandsandngersawayfromrotatingattachments.

•Alwaysholdtheworkpiecermlyagainstthetoolrest.Besurethetool

restissecurelytightenedinplacetopreventmovementduringuse.

•Donotgrindmagnesiumoraluminum,remayresult.

•Grindingcreateshazardoussparks,neveroperatethegrindernear

ammablegas,liquids,orinanexplosiveatmosphere.

•Dressthegrindingwheelfaceonly.Dressingthewheelsidescancauseitto

becometoothinforsafeuse.

•Ifanypartofthegrinderismissing,damagedorfailsinanyway,

orshouldanyelectricalcomponentfailtoperformproperly,shutofftheswitch.Removethe

machineplugfromthepowersourceandhavedamaged,missing,orfailedpartsreplaced

beforeresumingoperation.

•Cleanthegrindingdustfrombeneaththegrinderfrequently

•Donotoperateinrainorindamplocations.

•Groundingrequired.

SAVE THESE INSTRUCTIONS

1.ON/OFFSwitch

2.ToolRest

3.ToolRestLockingKnob

4.EyeShield

5.EyeShieldLockingknob

6.SparkGuard

7.Motor

8.WorkLights

9.WheelGuard

10.GrindingWheel

11.GrindingWheelLockingNut

12.GrindingWheelOuterFlange

13.MountingHoles

14.Base

English

8" Bench Grinder with Lights

Operator’s Manual GBG800L

YOUR 8" BENCH GRINDER

FIG 1

A  BenchGrinder 1 

B  EyeShieldBrackets 2

C  LeftSparkGuard 1

D  RightSparkGuard 1

E  LeftToolRest 1

F RightToolRest 1

G  EyeShieldLockingKnobs2

H  BracketLockingKnobs2

I  ToolRestLockingKnobs2

J  SmallFlatWashers 4

K BigFlatWahsers 2

L SmallLockWashers2

M BigLockWashers 2

N  StarLockWashers 2

O  ToolRestBolts 2

P  EyeShields 2

Q Operator'sManual(notshown)



English

UNPACKING AND CONTENT

IMPORTANT:Due to modern mass production techniques, it is

unlikely the tool is faulty or that a part is missing. If you ﬁnd anything

wrong, do not operate the tool until the parts have been replaced or

the fault has been rectiﬁed. Failure to do so could result in serious

personal injury.

Contents in Package: (FIG 2)

Item Description QTY Item Description QTY

WARNING: If any parts are missing or damaged, do not attempt to

assemble the tool, plug in power cord or turn the switch on until the missing or

damaged parts are replaced.

FIG 2

English

8" Bench Grinder with Lights

Operator’s Manual GBG800L

ASSEMBLY AND ADJUSTMENTS

 WARNING: Always be sure that the tool is switched off and unplugged

from the power source before adjusting, adding accessories, or checking a

function on the tool

Attaching and Adjusting Spark Guards and Eye Shields (FIG 3,4)

NOTE:

Alwayschecktoensuretheeyeshieldsarecorrectlyattachedandthesparkguardsare

correctlyadjustedeachtimethegrinderisused.Eyeshieldsandsparkguardsmustbeattachedover

eachgrindingwheel.

Thereisaleftandarightsparkguard.ConsultFIG3to

properlydeterminethemountingpositionofeachsparkguard.

FollowthestepstoattachtheSparkGuardandEyeShieldon

theLEFTsideofthegrinder.

1.InsertBracketLockingKnob(H)throughabiglockwasher

(M),abigatwasher(K),theeyeshieldbracket(B)andthe

LEFTsparkguard(C),thenscrewintotheholeintheleft

wheelguard.Tightensufcientlytoholdthesparkguard

andtheeyeshieldbracketinplace.(SeeFIG3)

2.Adjustthesparkguardtomakeitsloweredgeabout1/8"

(3.2mm)awayfromthegrindingwheelface.Rotatethe

wheelbyhandonerevolutiontoensurethewheelcanrotate

withoutcontactingwiththesparkguard.Firmlytightenthe

lockingknob(H)tosecurethesparkguardandeyeshield

bracketontothewheelguard.

3.Inserttheshieldlockingknob(G)throughastarwasher(N)

andasmallatwasher(J)andtheeyeshield(P),andthen

screwandtightensecurelyontotheeyeshieldbracket(B)

(seeFIG4)

RepeattheabovestepstoattachtheRIGHTsparkguardand

theeyeshieldontherightsideofthegrinder.

Attaching and Adjusting Tool Rests (FIG 5,6)

Thetoolrestsarerequiredforeachhighspeedgrindingwheel

toassistinthegrindingoperation.

WARNING: Never use a bench grinder on

which tool rest has not been attached or where

the tool rest has not been correctly adjusted.

NOTE:

Thereisaleftandarighttoolrest.Thetoolrestwith

v-groove(E)istheleftsidetoolrest(SeeFIG5).Whenproperly

mountedwiththeslottedportionofthetoolrestboltedushto

thetoolrestbracket,thetoolrestwillbepositioneddirectlyin

frontofthegrindingwheel.

1.HoldtheLEFTtoolrest(E)inthecorrectpositionagainstthetoolrestbracket(2)onleftwheel

guard(seeFIG6).

2.Inserttoolrestbolt(O)throughtoolrestbracket(2)andtoolrest(E),followedbyasmallatwasher

(J),asmalllockwasher(L),andthetoolrestlockingknob(I).

3.Tightenthelockingknob(I)sufcientlytosupportthetoolrestbutstillallowingthetoolresttoslide

inwardsandoutwards.

FIG 3

FIG 5

FIG 4

G JN

FIG 6

English

4.Slidethetoolresttowithinamaximumof1/16"(1.5mm)fromthewheel.Rotatethewheelonefull

revolutionbyhandtoensurethewheeldoesnotcontactthetoolrest.

5.Tightenthelockingknobrmlytoretaintheassembly.

6.RepeattheassemblyoperationfortheRIGHTtoolrest.

Mounting Bench Grinder

Ifduringoperationofthebenchgrinderthereisanytendencyforthegrindertoslideor"walk"orto

tipover,thenthegrindermustbesecuredtoaworkbenchorothersupportingsurfaceusingfasteners

(notsupplied)throughthetwoholesinthegrinderbase.

Beforemountingthegrindertoaworkbenchorsimilarsurface,determinetheidealmountingposition

byperformingaseriesofnon-poweredtestswithitemsthatwilltypicallybeusedonthegrinder(e.g.

lawnmowerblades,scissors,knives,woodchisels,woodturningtools,etc.)Thesetestsrunswillhelp

determinehowneartheworkbenchedgethegrindershouldbemountedsothatthebenchtopdoes

interferewithgrindingoperations.Besuretheworkbenchorpedestaltowhichthebenchgrinder

willbemountedisat,level,andsturdyenoughtobeartheweightofthegrinder,othertools,andthe

materialbeingworked.

Changing the Grinding Wheels (FIG 7)

WARNING: Useonlygrindingwheelsratedfor3,600rpmorhigherwith

a1/2"arborholeorappropriatesizedbushing.Neveruseagrindingwheel

ratedlowerthan3,600rpmorattempttomachineanundersizedwheeltot

the arbor.

1.Removethethreebolts(1)attachingtheprotectivesidecover(2)to

thegrinder;thenremovethesidecover.

2.Preventtheshaftfromrotatingbyplacingawedgebetweenthe

wheelandthetoolrest.

3.Facingthefrontofthebenchgrinder:toreplacethewheelon

theleftside,turnthearbornut(3)clockwisetoloosenand

counterclockwisetotightenthearbornut.

4.Toreplacethewheelontheright:turncounterclockwisetoloosen

andclockwisetotighten.

NOTE:Manygrindingwheelsuseremovableandadjustablearbor

bushingstoallowadaptationtovariousmachinearbordiameters.

Savethisbushingforfutureuseifnotneededtoinstallthe

replacementwheel.

5.Removethearbornut(3),outerange(4)andtheoldwheel.

6.Installthereplacementwheelandouterangeontheshaft.Make

surethewheelisslidet(notloose)ontheshaft.

7.Replacethearbornutandtighten.

8.Replacethesidecover.Reinsertthethreeboltsandtightentheside

coverinplace.

9.Re-adjusttoolrest,sparkguardandeyeshield.

10.Rotatethewheelbyhandtocheckfreemovementandproper

adjustments.

WARNING: Do not overtighten wheel nuts when installing grinding

wheels. Tighten the wheel nut enough to drive the wheel and prevent slippage.

FIG 7

English

8" Bench Grinder with Lights

Operator’s Manual GBG800L

OPERATION

IMPORTANT:Before each use of the bench grinder, inspect its general condition.

Check for loose screws, damaged electrical wiring, cracked, chipped, or damaged

wheels and misalignment or binding of the moving parts. If bench or pedestal

mounted, check that all fasteners are in place and tight.

CAUTION: Keep your bench grinder clean by removing dust from working parts,

the lower portion of the wheel guard assembly, and the work area surrounding the

grinder.

ON/OFF Switch (FIG 8)

TheSwitch(1)islocatedonthefrontofthegrinder.

To turn the grinder "ON",pushtherighthandportionof

theswitch,withthewhitedot,down.

To turn the grinder "OFF", pushthelefthandportionof

theswitchdown.

Work Light

Yourgrinderisequippedwithtwoexibleworklightsforbettervisibilityintheworkareaduring

operation.Whenthetoolisturnedon,thelightswillturnonautomaticallyandstayonuntilthetoolis

turnedoff.

 WARNING: Always be sure that the tool is switched off and unplugged

from the power source before adjusting, adding accessories, or checking a

function on the tool

Grinding Wheels

Forbestgrindingresultsandmaintaininggoodbalance,alwayskeepthewheel(s)properlydressed.

Neverforceaworkpieceagainstacoldwheelbutuselightpressureuntilthewheelbecomeswarm.

Westronglyrecommendusingonlybalancedwheelsonthesegrinders.Balancedwheelswilladdyears

oflifetogrinderbearingsandarborshaft,andeliminatethemostcommoncauseofvibration,which

willyieldmoreaccuratework.

Dressing a Grinding Wheel

Whenthegrindingwheelisoutofbalance,wornoutofshape,ordull,loadedandglazed,itmustbe

truedanddressed.Truingordressingthewheelisbestdoneusinga"star-wheel"dresser,silicone

carbidesticktypedresseroradiamondfaceddressingtool(notsupplied).Dressthewheelbymoving

thedresserforwardonthetoolrestuntilitjusttouchesthehighpointonthefaceofthewheel,then

dressthewheelbymovingthedresserbackandforthacrossthewheelface.Repeatthisprocedure

untilthefaceofthegrindingwheeliscleanandthecornersofthewheelsaresquare.

BASIC GRINDER OPERATIONS

 WARNING: Always wear safety goggles or safety glasses with side

shields during operation of any power tool. If the operation is dusty, wear

appropriate protective mask.

YourBenchGrinderisequippedwithonecoarsegrindingwheelandonemediumgrindingwheel.It

istheidealtoolforsharpeningtoolssuchaswoodchisels,coldchisels,planerblades,scissors,lawn

mowerblades,etc.

FIG 8

English

 WARNING: Never sharpen or grind anything made of or containing

aluminum or magnesium.

Becausegrinderscanremovematerialrapidly,afreshlydressedwheelandtheamountofworkpiece

pressureappliedtothewheelarekeystoefcientgrinding.Usethefollowingbasicguidelinestoaid

inworkingmetalsandavoidoverheating:

• Neverforcetheworkpieceagainstthegrindingwheel.

• Alwayskeeptheworkpiececonstantlymovingagainstthegrindingwheelwithlightpressure

andevenmotion.

• Keeptheworkpiececoolbymaintainingacontainerofwaternearbyfordippingthework

piece.

• Alwaysusethefaceofthegrindingwheelwiththewheelmovingdownward,intotheobject

beingworked.

• Donotperformgrindingoperationsonthesideofthewheel.

Lawn Mower Blades

Asyoupreparetosharpenthelawnmowerblade,ensurethereisadequateworkingspaceto

maneuvertheblade.Lawnmowerbladesaregenerallysharpenedonthebeveledsideandthen

dressedupslightlyontheothersidewiththegrinderorle.

Firstremoveanynicksthatmaybepresentonthecuttingedgebyrestingthebladeatonthetool

rest,movingthebladesidetosideuntiltheedgeisnickfree.Tosharpenthebevel,eitheradjustthe

toolrestangletomatchtheblade’sbevelangleorholdthebladeatthebevelanglewhilerestinga

portionofthebladeonthetoolrestforaddedstability.Usealighttouch,removingaslittlemetalas

possibletoattainthedesirededge;thenlightlydress-uptheatbacksideoftheblade.Ideally,lawn

mowerbladesshouldnotbehonedtorazorlikesharpness;thisincreasesthelikelihoodofnickingand

promotesrapiddulling.Usealeorthebenchgrindertolightlyfacethecuttingedge.

Afterthebladehasbeensharpened,besuretochecktheblade’sbalancewithanappropriateshop

madejigorcommerciallyavailableunit.Balancethebladebyprogressivelyremovingmetaluntil

balanceisattained.

 WARNING:An unbalanced lawn mower blade may cause excessive

vibration, causing damage to the mower and engine shaft.

Sharpening Twist Drill Bits:

Sharpeningtwistdrillscanbeatrickyoperationthatevensomeexperiencedmechanicsnevermaster.

Sharpeningtwistbitsfreehandwillrequireconsiderablepracticeanddryrunswiththegrinder

"OFF"toacquiretheskillofrotatingthebitwhilemaintainingtheoriginalcuttingedgeangle.Ifyou

anticipatesharpeningnumerousbitsconsiderpurchasingaspecializedsharpeningjig,availableat

mosthardwareandhomecenters.Atypicaltechniqueforsharpeningatwistdrillbitisasfollows:

1.Setthegroovedtoolresthorizontaltothefaceofthegrindingwheel.

2.Holdthedrillshankbetweenthethumbandindexnger,restingthebackoftheindexngeronthe

toolrest.

3.Besurethatthecuttinglipisstraightacrossthefaceofthewheelbeforebeginningeachstroke

4.Whenthedrillcontactsthewheel,pushthedrillshankdownwardandtotheleftataslightangle.At

thesametime,rotatethedrillsotheotherlipisjustvisible.

5.Repeatthisprocessontheotherliptosharpentheentiretwistdrill.

English

8" Bench Grinder with Lights

Operator’s Manual GBG800L

Sharpening Wood Chisels & Plane Irons:

Asinallfreehandsharpeningoperations,practicingthetechniqueandactualsharpeningexperience

arethebestteachers.Sharpeningchiselsandironsonthebenchgrinderwillproducerazorsharp

hollowgroundbevelswhichmustbefollowedbyhoningonawhetstone.Usethefollowingtipsto

helpdevelopyoursharpeningskillandsuccess.

1.Thechiselcuttingedgemustbefreeofnicksandbe90°tothechiseledge.Withthetoolrestat,

lightlydressthecuttingedgeifnicksarepresentorit’soutofsquare.

2.Adjustthetoolrestangleto25-30degreestothefaceofthegrindingwheel.Restthechiselon

theangledtoolrestandmoveitlaterallyacrossthefaceofthewheel.

3.Besuretooccasionallycoolthetoolinwatertomaintainitshardness.

4.Continuegrindingthecuttingedgeandbeveluntilthelengthofthebevelisroughlytwicethe

thicknessofthechisel.Removeonlythematerialnecessarytoachievethedesiredbevelangle

withasharpandsquarecuttingedge.

5.Thisprocessproducesasharphollowgroundbevelwithasmallamountof"wire"burrwhichwill

beremovedbynalhoningonawhetstone.

Consultwoodworkingpublicationsforadditionaltoolsharpeninginformationandexamplesofshop

madejigsandxturesandtechniquestonelytuneyourchisels,planeirons,planerblades,etc.

Refurbishing Screwdriver Tips:

Screwdrivertipsoftengetwornorbentoutofshapeandmustbereshapedbygrindingtoperform

properly.

1.Selectaat-headscrewwithaslotthesamewidthasthescrewdriverbladetip.

2.Grindscrewdrivertipsquareandremoveallgaps,nicks,andtwistsinthescrewdriverblade.

Applyonlylightpressuretothebladewhilemovingitbackandforthacrossthegrindingwheel

face.

3.Turnthescrewdriverfrequentlytokeepbothsidesparallel.

4.Ifgroundcorrectly,thetipshouldtcompletelyintothescrewslotwithnovisiblegaps.

MAINTENANCE

CLEANING

Avoidusingsolventswhencleaningplasticparts.Mostplasticsaresusceptibletodamagefrom

varioustypesofcommercialsolventsandmaybedamagedbytheiruse.Usecleanclothstoremove

dirt,dust,oil,grease,etc.

WARNING: Donotatanytimeletbrakeuids,gasoline,petroleum-

based products, penetrating oils, etc., come in contact with plastic parts.

Chemicals can damage, weaken or destroy plastic which may result in serious

personal injury.

Electrictoolsusedonberglassmaterial,wallboard,spacklingcompounds,orplasteraresubjectto

acceleratedwearandpossibleprematurefailurebecausetheberglasschipsandgroundingsare

highlyabrasivetobearings,brushes,commutators,etc.Consequently,wedonotrecommendusing

thistoolforextendedworkonthesetypesofmaterials.However,ifyoudoworkwithanyofthese

materials,itisextremelyimportanttocleanthetoolusingcompressedair.

LUBRICATION

Thistoolispermanentlylubricatedatthefactoryandrequiresnoadditionallubrication.

English

TWO-YEAR WARRANTY

Thisproductiswarrantedfreefromdefectsinmaterialandworkmanshipfor2yearsafterdate

ofpurchase.Thislimitedwarrantydoesnotcovernormalwearandtearordamagefromneglect

oraccident.Theoriginalpurchaseriscoveredbythiswarrantyanditisnottransferable.Priorto

returningyourtooltostorelocationofpurchase,pleasecallourToll-FreeHelpLineforpossible

solutions.THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL

PURPOSES. ACCESSORIES INCLUDED ARE NOT COVERED BY THE 2 YEAR WARRANTY.

TOLL-FREE HELP LINE

ForquestionsaboutthisoranyotherGENESISProduct,

PleasecallToll-Free:888-552-8665.(Mon-Fri,9:00amto4:30pmEST.)

Orvisitourwebsite:www.richpowerinc.com

Richpower Industries, Inc.

736 Hampton Road

Williamston, SC USA

Genesis Advanced Technologies GBG800L, Grinder GBG800L User manual

Other documents