Samsung CTI613GIN User manual

Brand: Samsung

Model: CTI613GIN

Category: Hobs

Type: User manual

This manual is also suitable for

CTI613GI

The Samsung CTI613GIN induction hob offers precise and efficient cooking with its state-of-the-art features. Equipped with touch control sensors, it allows for intuitive selection of cooking zones and heat settings. The appliance boasts a range of safety features, including a child safety lock, residual heat indicators, and automatic switch-off to prevent accidents. With its sleek and modern design, the Samsung CTI613GIN enhances your kitchen's style while providing a superior cooking experience.

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/global/register

Induction Hob

user manual

CTI613GI series

CTI613GI series_EN-00205A_XSA.in1 1 2009-02-25  10:10:28

2_ using this manual

using this manual

Please take the time to read this owner’s manual, paying particular attention

to the safety information contained in the following section, before using

your appliance. Keep this manual for future reference. If transferring

ownership of the appliance, please remember to pass the manual on to

the new owner.

THE FOLLOWING SYMBOLS ARE USED IN THE TEXT

This is the safety alert symbol.

Warning indicates information concerning your personal safety.

Important indicates information on avoiding damage to the appliance.

This symbol refers to measures that can be taken to help protect the

environment.

This symbol indicates useful information and practical tips.

1. Numbers like these indicate step - by - step instructions for using the appliance.

2. ...

3. ...

This manual contains information on steps you can take yourself to diagnose and resolve

problems that may arise. Refer to the section “Troubleshooting”.

CTI613GI series_EN-00205A_XSA.in2 2 2009-02-25  10:10:28

safety instructions _3

SAFETY INSTRUCTIONS

safety instructions

The safety aspects of this appliance comply with all accepted technical and safety

standards. However, as manufacturers we also believe it is our responsibility to

familiarize you with the following safety instructions.

ELECTRICAL SAFETY

• Be sure the appliance is properly installed and grounded by a qualiﬁed technician.

• The appliance should be serviced only by qualiﬁed service personnel. Repairs

carried out by unqualiﬁed individuals may cause injury or serious malfunction. If your

appliance is in need of repair, contact your local service centre. Failure to follow these

instructions may result in damage and void the warranty.

• Flush - mounted appliances may be operated only after they have been installed

in cabinets and workplaces that conform to the relevant standards. This ensures

sufﬁcient protection against contact for electrical units as required by the essential

safety standards.

• If your appliance malfunctions or if fractures, cracks or splits appear:

- switch off all cooking zones;

- disconnect the hob from the mains supply; and

- contact your local service centre.

If the surface is cracked, switch off the appliance to avoid the possibility of electric

shock.Do not use your hob until the glass surface has been replaced.

CHILD SAFETY

This appliance is not intended for use by young children or inﬁrm persons without

the adequate supervision of a responsible adult.

Young children should be supervised to ensure that they do not play with the

appliance.

The cooking zones will become hot when you cook. Always keep small children

away from the appliance.

CTI613GI series_EN-00205A_XSA.in3 3 2009-02-25  10:10:28

4_ safety instructions

SAFETY DURING USE

• Metallic objects such as knives, forks, spoons and lids should not be placed on the

hob surface since they can get hot.

• After use, switch off the hob element by its control and do not rely on the pan

detector.

• The appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

• This appliance is to be used only for normal cooking and frying in the home. It is not

designed for commercial or industrial use.

• Never use the hob for heating the room.

• Take care when plugging electrical appliances into mains sockets near the hob.

Mains leads must not come into contact with the cooktop.

• Overheated fat and oil can catch ﬁre quickly. Never leave surface units unattended

when preparing foods in fat or oil, for example, when cooking chips.

• Turn the cooking zones off after use.

• Always keep the control panels clean and dry.

• Never place combustible items on the hob. It may cause ﬁre.

• Do not use the hob to heat aluminium foil, products wrapped in aluminium foil or

frozen foods packaged in aluminium cookware.

• There is the risk of burns from the appliance if used carelessly.

• Cables from electrical appliances must not touch the hot surface of the hob or hot

cookware.

• Do not use the hob to dry clothes.

• Never store ﬂammable materials such as aerosols and detergents in draws or

cupboards under the hob.

Warning: Users with Pacemakers and Active Heart Implants must keep their upper

body at a minimum distance of 30cm from induction cooking zones when turned

on. If in doubt, you should consult the manufacturer of your device or your doctor.

SAFETY WHEN CLEANING

• Always turn the appliance off before cleaning.

• For safety reasons do not clean the appliance with a steam jet or high - pressure

cleaner.

• Clean the hob in accordance with the cleaning and care instructions contained in this

manual.

CTI613GI series_EN-00205A_XSA.in4 4 2009-02-25  10:10:28

disposal instructions _5

DISPOSAL INSTRUCTIONS

disposal instructions

DISPOSING OF THE PACKAGING MATERIAL

All materials used to package the appliance are fully recyclable. Sheet and hard

foam parts are appropriately marked. Please dispose of packaging materials and old

appliances with due regard to safety and the environment.

PROPER DISPOSAL OF YOUR OLD APPLIANCE

Warning: Before disposing of your old appliance, make it inoperable so that it

cannot be a source of danger.

To do this, have a qualiﬁed technician disconnect the appliance from the mains

supply and remove the mains lead.

• The appliance may not be disposed of in the household rubbish.

• Information about collection dates and public refuse disposal sites is available from

your local refuse department or council.

CTI613GI series_EN-00205A_XSA.in5 5 2009-02-25  10:10:29

6_ Contents

contents

INSTALLING THE HOB

7 Regulations and compliance

7 Safety instructions for the installer

8 Connecting to the mains power suppl

9 Installing into the counterto

PARTS AND FEATURES

11 Cooking zones

11 Control panel

12 Components

12 Induction heating

13 The key features of your appliance

14 Safety shutoff

14 Residual heat indicator

15 Temperature detection

BEFORE YOU BEGIN

15 Initial cleaning

HOB USE

16 Cookware for induction cooking zones

16 Suitability tes

16 Size of pan

17 Using suitable cookware

17 Using the touch control sensors

18 Switching the appliance on

18 Select cooking zone and heat settin

18 Switching the appliance of

19 Switching a cooking zone off

19 Using the child safety lock

20 Timer

21 Power boost contro

21 Bridge Control

22 Power Managemen

22 Suggested settings for cooking

speciﬁc foods

CLEANING AND CARE

23 Hob

24 Hob Fram

e (option)

24 To avoid damaging your appliance

WARRANTY AND SERVICE

25 FAQs and troubleshooting

26 Service

TECHNICAL DATA

27 Technical data

27 Cooking rings

CTI613GI series_EN-00205A_XSA.in6 6 2009-02-25  10:10:29

installing the hob _7

INSTALLING THE HOB

installing the hob

Important:

Be sure the new appliance is installed and grounded only by qualiﬁed personnel.

Please observe this instruction. The warranty will not cover any damage that may

occur as a result of improper installation.

Technical data is provided at the end of this manual.

REGULATIONS AND COMPLIANCE

This appliance meets the following standards:

• EN 60335 - 1 and EN 60335 - 2 - 6, relating to the safety of electrical appliances for

household use and similar purposes;

• EN 60350, or DIN 44546 / 44547 / 44548, relating to the operating features of electric

cookers, hobs, ovens, and grills for household use;

• EN 55014-1

• EN 55014-2

• EN 61000 - 3 - 2; and

• EN 61000 - 3 - 3, relating to basic requirements for electromagnetic compatibility (EMC).

This appliance complies with the following EU Directives:

• 2006/95/EC, Low Voltage Directive

• 2004/108/EEC, Electromagnetic Compatibility Directive

SAFETY INSTRUCTIONS FOR THE INSTALLER

• A device must be provided in the electrical installation that allows the appliance to be

disconnected from the mains at all poles with a contact opening width of at least 3 mm.

Suitable isolation devices include line protecting cut - outs, fuses (screw type fuses are to

be removed from the holder), earth leakage trips and contactors.

• With respect to ﬁre protection, this appliance corresponds to EN 60335 - 2 - 6. This type

of appliance may be installed with a high cupboard or wall on one side.

• Drawers may not be ﬁtted underneath the hob.

• The installation must guarantee shock protection.

• The kitchen unit in which the appliance is ﬁtted must satisfy the stability requirements of

DIN 68930.

• For protection against moisture, all cut surfaces are to be sealed with a suitable sealant.

• On tiled work surfaces, the joints in the area where the hob sits must be completely ﬁlled

with grout.

• On natural, artiﬁcial stone, or ceramic tops, the snap action springs must be bonded in

place with a suitable artiﬁcial resin or mixed adhesive.

• Ensure that the seal is correctly seated against the work surface without any gaps.

Additional silicon sealant must not be applied; this would make removal more difﬁcult

when servicing.

• The hob must be pressed out from below when removed.

• A board is to be installed underneath the hob.

• The ventilation gap between the worktop and front of the unit underneath it must not be

covered.

CTI613GI series_EN-00205A_XSA.in7 7 2009-02-25  10:10:29

8_ installing the hob

CONNECTING TO THE MAINS POWER SUPPLY

Before connecting, check that the nominal voltage of the appliance, that is, the voltage

stated on the rating plate, corresponds to the available supply voltage. The rating plate is

located on the lower casing of the hob.

Shut off power to circuit before connecting wires to circuit.

The heating element voltage is AC230 V~. The appliance also works perfectly on

networks with AC220 V~ or AC240 V~.

The hob is to be connected to the mains using a device that allows the appliance to be

disconnected from the mains at all poles with a contact opening width of at least 3 mm,

eg. automatic line protecting cut - out, earth leakage trips or fuse.

A type H05RN - F cable or one of a higher grade must be used as the mains connecting

cable.

Rated current of appliance (A) Nominal cross-sectional area (mm

)

1N~ > 25 and ≤ 32

≥ 2.5

2N~ > 10 and ≤ 16

≥ 1.5

The connection must be carried out as shown in the diagram. The connecting links

should be ﬁtted according to the appropriate connection diagram.

The earth lead is connected to terminal. The earth lead must be longer than leads

carrying electric current.

The cable connections must be made in accordance with regulations and

the terminal screws tightened securely.

The connecting cable is to be secured with the mains cable cleat and the covering

closed by pressing ﬁrmly (locking into place). Before switching on for the ﬁrst time, any

protective foil or stickers must be removed from the ceramic glass surface.

Once the hob is connected to the mains supply, check that all cooking zones are

ready for use by brieﬂy switching each on in turn at the maximum setting with suit-

able cookware.

When the hob is powered on for the ﬁrst time, all displays light and the child safety

lock is activated.

Warning: Pay attention (conformity) to phase and neutral allocation of house

connection and appliance (connection schemes); otherwise, components can be

damaged.

Warranty does not cover damage resulting from improper installation.

Warning: If the supply cord is damaged, it must be replaced by a special cord or

assembly available from the manufacturer or its service agent.

220-240V ~

380-415V ~

< IN ~ >

L: Brown

N: Blue

PE: Green

CTI613GI series_EN-00205A_XSA.in8 8 2009-02-25  10:10:29

installing the hob _9

INSTALLING THE HOB

INSTALLING INTO THE COUNTERTOP

Make a note of the serial number on the appliance rating plate prior to installation.

This number will be required in the case of requests for service and is no longer

accessible after installation, as it is on the original rating plate on the underside of

the appliance.

Pay special attention to the minimum space and clearance requirements.

Secure the brackets at both sides with the provided screws before mounting the

hob onto the brackets.

x 4

ø 6

90°

560

±1

min. 20

490

±1

600

Min. 50 mm

Min. 5 mm

560 mm

Induction Hob

ventilation gap

20 mm

min. 5 mm

Insulation Panel

Oven

CTI613GI series_EN-00205A_XSA.in9 9 2009-02-25  10:10:30

10_ installing the hob

90°

x 4

ø 2

100

490

±1

CTI613GI series_EN-00205A_XSA.in10 10 2009-02-25  10:10:30

parts and features _11

PARTS AND FEATURES

parts and features

COOKING ZONES

1. Induction cooking zone 2200W with Power Boost 3200W

2. Induction cooking zone 1400W with Power Boost 2000W

3. Induction front Bridge zone 1800W with Power Boost 2600W

4. Induction rear Bridge zone 1800W with Power Boost 2600W

5. Induction complete Bridge zone 3600W with Power Boost 5200W

6. Control panel

CONTROL PANEL

1. Cooking zone selectors

2. Heat setting selectors and Timer setting selectors

3. Lock control sensor

On/Off control sensor

5. Power Boost selector

6. Power Pre-selections

7. Indicators for heat settings and residual heat

Timer indicator and control sensor

Complete Bridge zone selector

210 mm

160 mm

8 6 5

431

7 9

CTI613GI series_EN-00205A_XSA.in11 11 2009-02-25  10:10:30

12_ parts and features

COMPONENTS

Induction Hob Installation Brackets Screws

INDUCTION HEATING

• The Principle of Induction Heating: When you place your cookware on a cooking

zone and you turn it on, the electronic circuits in your induction hob produce

“induced currents” in the bottom of the cookware which instantly raise cookware’s

temperature.

• Greater speed in cooking and frying: As the pan is heated directly and not the

glass, the efﬁciency is greater than in other systems because no heat is lost. Most of

the energy absorbed is transformed into heat.

Induction coil

Induced currents

Electronic circuits

CTI613GI series_EN-00205A_XSA.in12 12 2009-02-25  10:10:30

parts and features _13

PARTS AND FEATURES

THE KEY FEATURES OF YOUR APPLIANCE

• Ceramic glass cooking surface: The appliance has a ceramic glass cooking

surface and four rapid - response cooking zones.

• Touch control sensors: Your appliance is operated using touch control sensors.

• Easy cleaning: The advantage of the ceramic glass cooking surface and the control

sensors is their accessibility for cleaning. The smooth, ﬂat surface is easy to clean.

• On / Off sensor: The “On / Off” control sensor provides the appliance with a

separate mains switch. Touching this sensor switches the power supply on or off

completely.

• Control and function indicators: Digital displays and indicator lights provide

information about settings and activated functions, as well as the presence of

residual heat in the various cooking zones.

• Safety shutoff: A safety shutoff ensures that cooking zones switch off automatically

after a period of time if the setting has not been changed.

• Residual heat indicator: An icon for residual heat appears in the display if the

cooking zone is so hot that there is a risk of burning.

• Power Pre-selections: You can choose pre-selected power conveniently.

Heat setting ‘ ’

• Power Boost : Use this function to heat up the contents of the pan faster than

maximum power level ‘ ’. ( The display will show ‘ ’. )

• Complete Bridge zone selector : Use this function to expand cooking zone into

complete right side.

• Auto Pan-Detection: Each cooking zone incorporates an automatic pan-detection

system, the system is calibrated in order to recognize pans of a diameter just slightly

smaller than the cooking zone. Pans must always be placed centrally on each

cooking zone. And you should use suitable cookware.

• Digital displays: The four display ﬁelds are assigned to the four cooking zones.

They show the following information:

- the appliance has been switched on,

- to ,

selected heat settings,

- residual heat,

- the child lock is activated; and

- error message, the sensor has been touched for longer than 10

seconds.

- error message, when the hob is overheated because of abnormal

operation. (example : operation with empty cookware)

error message, cookware is unsuitable or too small or no cookware has

been placed on the cooking zone.

CTI613GI series_EN-00205A_XSA.in13 13 2009-02-25  10:10:31

14_ parts and features

SAFETY SHUTOFF

If one of the cooking zones is not switched off or the heat setting is not adjusted after an

extended period of time, that particular cooking zone will automatically switch itself off.

Any residual warmth will be indicated with (for “hot”) in the digital displays

corresponding to the particular cooking zones.

The cooking zones switch themselves off at the following times.

Heat setting Switch off

1-3 After 6 hours

4-6 After 5 hours

7-9 After 4 hours

10-15 After 1.5 hours

If the Hob is overheated because of abnormal operation, will be displayed.

And the Hob will be switched off.

If cookware is unsuitable or too small or no cookware has been placed on the

cooking zone, will be displayed. And after 5 minutes the corresponding cooking

zone will be switched off.

Should one or more of the cooking zones switch off before the indicated time has

elapsed, see the section “Troubleshooting”.

Other reasons why a cooking zone will switch itself off

All cooking zones will immediately switch themselves off if liquid boils over and

lands on the control panel.

The automatic shutoff will also be activated if you place a damp cloth on the

control panel. In both of these instances, the appliance will need to be switched

on again using the main On/Off control sensor after the liquid or the cloth

has been removed .

RESIDUAL HEAT INDICATOR

When an individual cooking zone or the hob is turned off, the presence of residual heat is

shown with an (for “hot”) in the digital display of the appropriate cooking zones. Even

after the cooking zone has been switched off, the residual heat indicator goes out only

after the cooking zone has cooled.

You can use the residual heat for thawing or keeping food warm.

Important: As long as the residual heat indicator is illuminated, there is a risk of

burns.

Important: If the power supply is interrupted, the symbol will go out and

information about residual heat will no longer be available. However, it may still be

possible to burn yourself. This can be avoided by always taking care when near the

hob.

CTI613GI series_EN-00205A_XSA.in14 14 2009-02-25  10:10:32

before you begin _15

BEFORE YOU BEGIN

TEMPERATURE DETECTION

If for any reason the temperatures on any of the cooking zones were to exceed the

safety levels, should this happen then the cooking zone will automatically reduce to a

lower power level.

When you have ﬁnished using the hob, the cooling fan will continue to run until the hob’s

electronics has cooled down. And the cooling fan switched itself on and off depending

upon the termperature of the electronics.

before you begin

INITIAL CLEANING

Wipe the ceramic glass surface with a damp cloth and ceramic cooktop glass cleaner.

Important: Do not use caustic or abrasive cleaners. The surface could be

damaged.

CTI613GI series_EN-00205A_XSA.in15 15 2009-02-25  10:10:32

16_ hob use

hob use

COOKWARE FOR INDUCTION COOKING ZONES

The induction hob can only be turned on when a cookware with a magnetic base is

placed on one of the cooking zones. You can use the following suitable cookware.

Cookware material

Cookware material Suitable

Steel, Enamelled steel Yes

Cast iron Yes

Stainless steel If appropriately labelled by the manufacturer

Aluminium, Copper, Brass No

Glass, Ceramic, Porcelain No

Cookware for induction hob is labelled as suitable by the manufacturer.

Certain cookware can make noise when being used on induction cooking

zones. These noise are not a fault in the appliance and do not affect

operation in any way.

SUITABILITY TEST

Cookware is suitable for induction cooking,

if a magnet sticks to the bottom of the

cookware.

SIZE OF PANS

Induction cooking zones adapt automatically to the size of the bottom of the cookware

up to a cerain limit. However the magnetic part of the bottom of the cookware must

have a minimum diameter depending upon the size of the cooking zone.

Diameter of cooking zones Minimum diameter of the bottom of the cookware

210 mm 180 mm

160 mm 100 mm

Front or Rear Bridge 145 mm

Complete Bridge 180mm, oval, ﬁ sh kettle

CTI613GI series_EN-00205A_XSA.in16 16 2009-02-25  10:10:32

hob use _17

HOB USE

USING SUITABLE COOKWARE

Better pans produce better results.

• You can recognise good pans by their bases. The base should be as thick and ﬂat as

possible.

• When buying new pans, pay particular attention to the diameter of the base.

Manufacturers often give only the diameter of the upper rim.

• Do not use pans which have damaged bases with rough edges or burrs. Permanent

scratching can occur if these pan are slid across the surface.

• When cold, pan bases are normally bowed slightly inwards (concave). They should

never be bowed outwards (convex).

• If you wish to use a special type of pan, for example, a pressure cooker, a simmering

pan, or a wok, please observe the manufacturer’s instructions.

Energy saving tips

You can save valuable energy by observing the following points.

• Always position pots and pans

before switching on the cooking

zone.

• Dirty cooking zones and pan bases

increase power consumption.

• When possible, position the lids

ﬁrmly on the pots and pans to

cover completely.

• Switch the cooking zones off before

the end of the cooking time to use

the residual heat for keeping foods

warm or for thawing.

USING THE TOUCH CONTROL SENSORS

To operate the touch control sensors, touch the desired panel with the tip of your

pointed ﬁnger until the relevant displays illuminate or go out, or until the desired function

is activated.

Ensure that you are touching only one sensor panel when operating the appliance. If

your ﬁnger is too ﬂat on the panel, an adjacent sensor may be actuated as well.

Right!

Wrong!

CTI613GI series_EN-00205A_XSA.in17 17 2009-02-25  10:10:32

18_ hob use

SWITCHING THE APPLIANCE ON

1. Touch the Lock control sensor for approximately 3 seconds.

The appliance is switched on using the On/Off

control sensor.

Touch the On/Off control sensor for 1

second.

The digital displays will show .

After the On/Off control sensor has been actuated to switch on

your appliance, a heat setting must be selected within approximately 10

seconds. Otherwise, the appliance will switch itself off for safety reasons.

SELECT COOKING ZONE AND HEAT SETTING

1. For selecting the cooking zone, touch the

corresponding cooking zone’s key.

For setting and adjusting the power level (

) for cooking, touch the Heat setting

selectors ( or ).

For faster adjustment, keep your ﬁnger on the Heat setting selectors (

or ) until the required value is obtained.

If more than one sensor is pressed for longer than 10 seconds, will

show in the heat setting display. To reset, touch the On/Off control

sensor.

SWITCHING THE APPLIANCE OFF

To completely switch off the appliance, use the

On/Off control

sensor.

Touch the On/Off control sensor.

approx

1 sec.

CTI613GI series_EN-00205A_XSA.in18 18 2009-02-25  10:10:33

hob use _19

HOB USE

After switching off a single cooking zone or the entire cooking surface,

the presence of residual heat will be indicated in the digital displays of the

corresponding cooking zones in the form of an (for “hot”).

SWITCHING A COOKING ZONE OFF

To switch off a cooking zone, return the setting to

by using the control panel’s control sensor.

To switch off more quickly, touch the corresponding cooking zone’s key

twice.

USING THE CHILD SAFETY LOCK

You can use the child safety lock to safeguard against unintentionally turning on a

cooking zone and activating the cooking surface.

Also the control panel, with the exception of the On/Off control sensor, can

be locked in order to prevent the settings from being changed unintentionally, for

example, by wiping over the panel with a cloth.

Switching the child safety lock on / off

1. Touch the Lock control sensor for

approximately 3 seconds.

An acoustic signal will sound as conﬁ rmation.

2. Touch any control sensor .

will appear in the displays, indicating the child safety lock

has been activated.

3. For switching the child safety lock off, touch the Lock control sensor

again for 3 seconds.

An acoustic signal will sound as conﬁ rmation.

approx

3 sec.

CTI613GI series_EN-00205A_XSA.in19 19 2009-02-25  10:10:34

20_ hob use

TIMER

There are two ways to use the timer:

Using the timer as a safety shutoff:

If a speciﬁc time is set for a cooking zone, the cooking zone will shut itself off once

this period of time has elapsed. This function can be used for multiple cooking zones

simultaneously.

Using the timer to count down:

The countdown timer cannot be used if a cooking zone has been switched on.

Setting the safety shutoff

The cooking zone(s) for which you want to apply the safety shutoff must be

switched on.

1. Using the Timer control sensor, select the

cooking zone for which the safety shutoff time

is to be set.

After the ﬁrst active cooking zone is selected,

touching the timer’s control sensor will cause

the corresponding indicator to ﬂash slowly.

For example, the front left indicator

corresponds to the front left cooking zone. will appear in the timer

display.

The next active cooking zone is selected by touching the Timer control

sensor again .

Use the Timer setting selectors (

or ) to set the desired amount

of time, for example, 15 minutes,

after which the cooking zone will

automatically switch itself off.

The safety shutoff is now activated.

To display the time remaining for any of the cooking zones, use the Timer

control sensor.

The corresponding control indicator will begin to blink slowly.

The settings are reset using the Timer setting selectors ( or ). After the

set period of time has elapsed, the cooking zone automatically switches itself off,

an acoustic signal sounds as conﬁrmation and the timer display indicates .

To make the settings more quickly, touch any of the or control

sensors until the desired value is reached.

If the control sensor is touched ﬁrst, the time setting will begin at 99

minutes; if the control sensor is touched ﬁrst, the time setting will begin

at 1 minute.

CTI613GI series_EN-00205A_XSA.in20 20 2009-02-25  10:10:34

Page is loading ...

Samsung CTI613GIN User manual

Brand: Samsung

Model: CTI613GIN

Category: Hobs

Type: User manual

This manual is also suitable for

CTI613GI

Download PDF

report

Samsung CTI613GIN User manual

This manual is also suitable for

Samsung CTI613GIN User manual

Related papers

Other documents