Cisco Systems BEFSR81 User manual

USER GUIDE

EtherFast

®

Cable/DSL Router

with 8-Port Switch

Model: BEFSR81

About This Guide

i

EtherFast Cable/DSL Router with 8-Port Switch

About This Guide

Icon Descriptions

While reading through the User Guide you may see

various icons that call attention to specific items. Below is

a description of these icons:

NOTE: This check mark indicates that there is

a note of interest and is something that you

should pay special attention to while using the

product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is

something that could damage your property or

product.

WEB: This globe icon indicates a noteworthy

website address or e-mail address.

Online Resources

Website addresses in this document are listed without

http:// in front of the address because most current web

browsers do not require it. If you use an older web browser,

you may have to add http:// in front of the web address.

Resource Website

Linksys www.linksys.com

Linksys International www.linksys.com/international

Glossary www.linksys.com/glossary

Network Security www.linksys.com/security

Copyright and Trademarks

Linksys, EtherFast, Cisco, and the Cisco Logo

are registered trademarks or trademarks

of Cisco Systems, Inc. and/or its affiliates

in the U.S. and certain other countries.

rights reserved. Other brands and product

names are trademarks or registered

trademarks of their respective holders.

Table of Contents

ii

EtherFast Cable/DSL Router with 8-Port Switch

Chapter 1: Product Overview 1

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Chapter 2: Advanced Conguration 2

How to Access the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Security > Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Security > VPN Passthrough. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Applications and Gaming > Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . . 9

Applications & Gaming > Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Applications and Gaming > UPnP Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Appendix A: Troubleshooting 16

Appendix B: Specications 17

Appendix C: Warranty Information 18

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Appendix D: Regulatory Information 20

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Appendix E: Software License Agreement 25

Software in Linksys Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Chapter 1

Product Overview

1

EtherFast Cable/DSL Router with 8-Port Switch

Chapter 1:

Product Overview

Thank you for choosing the Linksys by Cisco EtherFast

Cable/DSL Router with 8-Port Switch. The Router lets

you access the Internet through its eight switched ports.

You can also use the Router to share resources such as

computers, printers and files. A variety of security features

help to protect your data and your privacy while online.

Security features include a Stateful Packet Inspection (SPI)

firewall and NAT technology. Configuring the Router is

easy using the provided browser-based utility.

Front Panel

QoS (Green) The QoS LED lights up when the

QoS feature is active.

Power (Green) The Power LED lights up and

will stay on while the Router is powered on.

It flashes when the Router goes through its

self-diagnostic mode during every boot-up or

upgrades its firmware.

1-8 (Green) These numbered LEDs correspond

with the numbered ports on the Router’s back

panel. These LEDs have a dual function. If the

LED is continuously lit, the Router is successfully

connected to a device through that port. A

flashing LED indicates network activity over

that port.

Internet (Green) The Internet LED lights up

when there is a connection made through the

Internet port. A flashing LED indicates network

activity over the Internet port.

Back Panel

Reset There are two ways to reset the Router to

its factory default settings. Use a straightened

paper clip or similar object to press and hold the

Reset button for approximately five seconds.

You can also restore the defaults from the

Administration > Factory Defaults screen of the

Router’s web-based utility.

Internet The Internet port is where you will

connect your cable or DSL Internet connection.

1-8 These Ethernet ports (1, 2, 3, 4, 5, 6, 7, 8)

connect the Router to computers on your wired

network and other Ethernet network devices.

Power The Power port is where you will

connect the power adapter.

Chapter 2

Advanced Configuration

2

EtherFast Cable/DSL Router with 8-Port Switch

Chapter 2:

Advanced Configuration

After setting up the Router with the Setup Wizard (located

on the CD-ROM), the Router will be ready for use. However,

if you’d like to change its advanced settings, use the

Router’s web-based utility. This chapter describes each

web page of the utility and each page’s key functions. You

can access the utility via a web browser on a computer

connected to the Router.

The web-based utility has these main tabs: Setup, Security,

Applications & Gaming, Administration, and Status.

Additional tabs will be available after you click one of the

main tabs.

NOTE: When first installing the Router, you

should use the Setup Wizard on the Setup

CD-ROM. If you want to configure advanced

settings, use this chapter to learn about the

web-based utility.

How to Access the Web-Based Utility

To access the web-based utility, launch the web browser on

your computer, and enter the Router’s default IP address,

192.168.1.1, in the Address field. Then, press Enter.

A login screen will appear. Leave the User Name field

blank. The first time you open the web-based utility, use

the default password admin. (You can set a new password

from the Administration > Management screen.) Click OK

to continue.

Login Screen

Setup > Basic Setup

The first screen that appears is the Basic Setup screen. This

allows you to change the Router’s general settings.

Setup > Basic Setup

Internet Setup

The Internet Setup section configures the Router to your

Internet connection. Most of this information can be

obtained through your Internet Service Provider (ISP).

Internet Connection Type

Select the type of Internet connection your ISP provides

from the drop-down menu. These are the available types:

Obtain an IP Automatically •

Static IP •

PPPoE •

RAS •

PPTP •

Heart Beat Signal •

L2TP •

Obtain an IP Automatically

By default, the Router’s Internet Connection Type is set to

Obtain an IP automatically, which should be kept only if

your ISP supports DHCP or you are connecting through a

dynamic IP address. (This option usually applies to cable

connections.)

Internet Connection Type > Obtain an IP Automatically

Chapter 2

Advanced Configuration

3

EtherFast Cable/DSL Router with 8-Port Switch

Static IP

If you are required to use a permanent IP address to

connect to the Internet, select Static IP.

Internet Connection Type > Static IP

IP Address Enter the Router’s IP address, as seen from the

Internet. This is provided by your ISP.

Subnet Mask Enter the Router’s subnet mask, as seen by

users on the Internet (including your ISP). This is provided

by your ISP.

Default Gateway Your ISP will provide you with the IP

address of the ISP server.

Static DNS 1-3 Your ISP will provide you with at least one

DNS (Domain Name System) server IP address.

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocol

over Ethernet) to establish Internet connections. If you are

connected to the Internet through a DSL line, check with

your ISP to see if they use PPPoE. If they do, you will have

to enable PPPoE.

Internet Connection Type > PPPoE

User Name and Password Enter the User Name and

Password provided by your ISP.

Service Name If provided by your ISP, enter the Service

Name.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

RAS

Remote Access Service (RAS) is a service that applies to

connections in Singapore only. For users in Singapore,

check with Singtel for information on RAS.

Internet Connection Type > RAS

User Name and Password Enter the User Name and

Password provided by Singtel.

RAS Plan Select the type of plan you have.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5 minutes.

Keep Alive: Redial Period

If you select this option, the

Router will periodically check your Internet connection. If

you are disconnected, then the Router will automatically

re-establish your connection. To use this option, select

Keep Alive. In the Redial Period field, you specify how often

you want the Router to check the Internet connection. The

default value is 30 seconds.

Chapter 2

Advanced Configuration

4

EtherFast Cable/DSL Router with 8-Port Switch

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service that

applies to connections in Europe only.

Internet Connection Type > PPTP

IP Address Enter the Router’s IP address, as seen from the

Internet. This is provided by your ISP.

Subnet Mask Enter the Router’s subnet mask, as seen by

users on the Internet (including your ISP). This is provided

by your ISP.

Default Gateway Your ISP will provide you with the IP

address of the ISP server.

User Name and Password Enter the User Name and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5 minutes.

Keep Alive: Redial Period

If you select this option, the

Router will periodically check your Internet connection. If

you are disconnected, then the Router will automatically

re-establish your connection. To use this option, select

Keep Alive. In the Redial Period field, you specify how often

you want the Router to check the Internet connection. The

default value is 30 seconds.

Heart Beat Signal

Heart Beat Signal is a service used in Australia only. If you

are using a Heart Beat Signal connection, check with your

ISP for the necessary setup information.

Internet Connection Type > Heart Beat Signal

User Name and Password Enter the User Name and

Password provided by your ISP.

Heart Beat Server Enter the IP address of your ISP’s Heart

Beat server. This is provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5 minutes.

Keep Alive: Redial Period

If you select this option, the

Router will periodically check your Internet connection. If

you are disconnected, then the Router will automatically

re-establish your connection. To use this option, select

Keep Alive. In the Redial Period field, you specify how often

you want the Router to check the Internet connection. The

default value is 30 seconds.

L2TP

L2TP is a service that applies to connections in Israel only.

Internet Connection Type > L2TP

Server IP Address Enter the IP address of the L2TP server.

This is provided by your ISP.

User Name and Password Enter the User Name and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

Chapter 2

Advanced Configuration

5

EtherFast Cable/DSL Router with 8-Port Switch

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify

with your ISP before making any changes.

Optional Settings

Host Name and Domain Name These fields allow you to

supply a host and domain name for the Router. Some ISPs,

usually cable ISPs, require these names as identification.

You may have to check with your ISP to see if your

broadband Internet service has been configured with a

host and domain name. In most cases, leaving these fields

blank will work.

MTU MTU is the Maximum Transmission Unit. It specifies

the largest packet size permitted for Internet transmission.

Select Enable if you want to manually enter the largest

packet size that is transmitted. To have the Router select

the best MTU for your Internet connection, keep the

default setting, Disable.

Size When Manual is selected in the MTU field, this option

is enabled. Leave this value in the 1200 to 1500 range. The

default size depends on the Internet Connection Type:

DHCP, Static IP, or Telstra: • 1500

PPPoE: • 1492

PPTP or L2TP: • 1460

Network Setup

The Network Setup section changes the settings on the

network connected to the Router’s Ethernet ports.

Router IP

This presents both the Router’s IP Address and Subnet

Mask as seen by your network.

Router IP

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic

Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A

DHCP server automatically assigns an IP address to each

computer on your network. If you choose to enable the

Router’s DHCP server option, make sure there is no other

DHCP server on your network.

Network Address Server Settings (DHCP)

Local DHCP Server DHCP is enabled by factory default.

If you already have a DHCP server on your network, or you

don’t want a DHCP server, then select Disable (no other

DHCP features will be available).

Start IP Address Enter a value for the DHCP server to

start with when is

suing IP addresses. Because the Router’s

default IP address is 192.168.1.1, the Start IP Address must

be 192.168.1.2 or greater, but smaller than 192.168.1.253.

The default is 192.168.1.100

.

Number of Address Enter the maximum number of

computers that you want the DHCP server to assign IP

addresses to. This number cannot be greater than 253.

The default is 50.

DHCP Address Range Displayed here is the range of

available IP addresses.

Client Lease Time The Client Lease Time is the amount

of time a network user will be allowed connection to the

Router with their current dynamic IP address. Enter the

amount of time, in minutes, that the user will be “leased”

this dynamic IP address. After the time is up, the user will

be automatically assigned a new dynamic IP address. The

default is 0 minutes, which means one day.

Static DNS 1-3

The Domain Name System (DNS) is how

the Internet translates domain or website names into

Internet addresses or URLs. Your ISP will provide you with at

least one DNS Server IP address. If you wish to use another,

enter that IP address in one of these fields. You can enter up

to three DNS Server IP addresses here. The Router will use

these for quicker access to functioning DNS servers

.

WINS The Windows Internet Naming Service (WINS)

manages each PC’s interaction with the Internet. If you

use a WINS server, enter that server’s IP address here.

Otherwise, leave this blank.

Chapter 2

Advanced Configuration

6

EtherFast Cable/DSL Router with 8-Port Switch

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS)

feature. DDNS lets you assign a fixed host and domain

name to a dynamic Internet IP address. It is useful when

you are hosting your own website, FTP server, or other

server behind the Router.

Before you can use this feature, you need to sign

up for DDNS service with a DDNS service provider,

www.dyndns.org or www.TZO.com. If you do not want to

use this feature, keep the default setting, Disabled.

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then

select DynDNS.org from the drop-down menu. If your

DDNS service is provided by TZO, then select TZO. The

features available on the DDNS screen will vary, depending

on which DDNS service provider you use.

DynDNS.org

Setup > DDNS > DynDNS.org

User Name Enter the User Name for your DDNS account.

Password Enter the Password for your DDNS account.

Host Name The is the DDNS URL assigned by the DDNS

service.

Internet IP Address The Router’s Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

TZO.com

Setup > DDNS > TZO

E-mail Address, TZO Password Key, and Domain

Name Enter the settings of the account you set up with

TZO.

Internet IP Address The Router’s Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a unique

piece of hardware for identification. Some ISPs will require

you to register a MAC address in order to access the

Internet. If you do not wish to re-register the MAC address

with your ISP, you may assign the MAC address you have

currently registered with your ISP to the Router with the

MAC Address Clone feature.

Setup > MAC Address Clone

Chapter 2

Advanced Configuration

7

EtherFast Cable/DSL Router with 8-Port Switch

MAC Clone

MAC Clone Service To have the MAC address cloned,

select Enable.

MAC Address Enter the MAC address registered with

your ISP here.

Clone Click this button to clone the MAC address of the

computer you are using.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Setup > Advanced Routing

This screen is used to set up the Router’s advanced

functions. Dynamic Routing automatically adjusts how

packets travel on your network. Static Routing sets up a

fixed route to another network destination.

Setup > Advanced Routing

Advanced Routing

NAT

Enable/Disable If this Router is hosting your network’s

connection to the Internet, keep the default, Enable. If

another router exists on your network, select Disable.

When the NAT setting is disabled, the Dynamic Routing

feature can be enabled.

Dynamic Routing (RIP)

Enable/Disable This feature enables the Router to

automatically adjust to physical changes in the network’s

layout and exchange routing tables with the other router(s).

The Router determines the network packets’ route based

on the fewest number of hops between the source and

the destination. When the NAT setting is enabled, the

Dynamic Routing feature is automatically disabled. When

the NAT setting is disabled, this feature is available. Select

Enable to use the Dynamic Routing feature.

Transmit RIP Version To use dynamic routing for

transmission of network data, select the protocol you

want: RIP1, RIP1-Compatible, or RIP2.

Receive RIP Version To use dynamic routing for reception

of network data, select the protocol you want, RIP1 or

RIP2.

Static Routing

A static route is a pre-determined pathway that network

information must travel to reach a specific host or network.

Enter the information described below to set up a new

static route.

Select Entry To set up a static route between the Router

and another network, select a number from the drop-

down list. Click Delete Entry to delete a static route.

Destination IP Address Enter the IP address of the

remote network or host to which you want to assign a

static route.

Subnet Mask Enter the subnet mask. This determines

which portion of a Destination IP Address is the network

portion, and which portion is the host portion.

Gateway Enter the IP address of the gateway device that

allows for contact between the Router and the remote

network or host.

Hop Count Enter the maximum number of steps between

network nodes that data packets will travel. A node is any

device on the network, such as a computer, print server,

or router.

Interface Select the appropriate interface. This tells you

whether the Destination IP Address is on the LAN (Local

Area Network) or the Internet.

Click Show Routing Table to view the static routes you

have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet

Mask, Gateway, Hop Count, and Interface are displayed.

Click Refresh to update the information.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Chapter 2

Advanced Configuration

8

EtherFast Cable/DSL Router with 8-Port Switch

Security > Filter

The Filter screen is used to set up filters to block specific

internal users from accessing the Internet and enhance

your network’s security.

Security > Filter

Filter IP Address Range

You can create up to five different IP Address Range filters.

Users who have filtered IP addresses will not be able to

access the Internet at all. If you only want to filter one IP

address instead of a range of IP addresses, enter the same

value into both fields. For instance, if you wish to filter the

PC with the IP address of 192.168.1.5, enter 5 into both

fields on one line: 192.168.1.5 ~ 192.168.1.5.

Start Enter the starting IP address of the range you wish

to filter.

End Enter the ending IP address of the range you wish

to filter.

Filter Port Range

You can create up to five different Port Range filters. Users

connected to the Router will no longer be able to access

any port number listed here.

Protocol Select the protocol you want to filter, TCP, UDP,

or Both.

Start Enter the starting port number of the range you

wish to filter.

End Enter the ending port number of the range you wish

to filter.

Filter MAC Address

This feature blocks computers with specific MAC addresses

from going out to the Internet.

Edit MAC Filter Setting To set the MAC filter, click Edit

MAC Filter Setting.

Filter > MAC Access Control Table

Use the MAC Access Control Table to select the MAC

addresses you want to filter.

Filtered MAC Address • Select the range of MAC

address entries.

mac 1-10 • Enter the MAC address.

Click Apply before closing the window. To cancel

changes, click Undo.

Block WAN Requests

Use these features to enhance your network’s security and

filter multicasting.

Block Anonymous Internet Requests This feature

makes it more difficult for outside users to work their

way into your network. This feature is enabled by default.

Select Disabled to allow anonymous Internet requests

.

Filter Multicast Multicasting allows for multiple

transmissions to specific recipients at the same time. If

multicasting is permitted, then the Router will allow IP

multicast packets to be forwarded to the appropriate

computers. Select Enabled to filter multicasting. This

feature is disabled by default.

Filter Internet NAT Redirection This feature uses port

forwarding to block access to local servers from local

networked computers. Select Enabled to filter Internet

NAT redirection. This feature is disabled by default.

Filter IDENT (Port 113) This feature keeps port 113 from

being scanned by devices outside of your local network.

This feature is enabled by default. Select Disabled to allow

port 113 to be scanned.

Chapter 2

Advanced Configuration

9

EtherFast Cable/DSL Router with 8-Port Switch

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Security > VPN Passthrough

The VPN Passthrough screen allows you to enable VPN

tunnels using IPSec, PPPoE, or PPTP protocols to pass

through the Router’s firewall.

Security > VPN Passthrough

VPN Passthrough

IPSec Passthrough Internet Protocol Security (IPSec) is

a suite of protocols used to implement secure exchange

of packets at the IP layer. To allow IPSec tunnels to pass

through the Router, keep the default, Enabled.

PPPoE Passthrough Point-to-Point over Ethernet

(PPPoE) Passthrough allows your computer(s) to use the

PPPoE client software provided by your ISP. Some ISPs

may request that you use this feature on the Router. To

allow PPPoE Passthrough, keep the default, Enabled.

PPTP Passthrough Point-to-Point Tunneling Protocol

(PPTP) allows the Point-to-Point Protocol (PPP) to be

tunneled through an IP network. To allow PPTP tunnels to

pass through the Router, keep the default, Enabled.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Applications and Gaming > Port Range

Forwarding

The Port Range Forwarding screen allows you to set up

public services on your network, such as web servers,

ftp servers, e-mail servers, or other specialized Internet

applications. (Specialized Internet applications are any

applications that use Internet access to perform functions

such as videoconferencing or online gaming. Some Internet

applications may not require any forwarding.)

When users send these types of requests to your network via

the Internet, the Router will forward those requests to the

appropriate servers (computers). Before using forwarding,

you should assign static IP addresses to the designated

servers.

If you need to forward all ports to one computer, click the

DMZ tab.

Applications and Gaming > Port Range Forwarding

Port Range Forwarding

To forward a port, enter the information on each line for

the criteria required.

Application In this field, enter the name you wish to give

the application. Each name can be up to 12 characters.

Start and End Enter the number or range of port(s)

used by the server or Internet applications. Check

with the Internet application documentation for more

information.

Protocol Select the protocol used for this application,

either TCP or UDP, or Both.

IP Address For each application, enter the IP address of

the PC running the specific application.

Enabled Select Enabled to enable port forwarding for

the applications you have defined.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Applications & Gaming > Port Triggering

The Port Triggering screen allows the Router to watch

outgoing data for specific port numbers. The IP address of

the computer that sends the matching data is remembered

by the Router, so that when the requested data returns

through the Router, the data is pulled back to the proper

computer by way of IP address and port mapping rules.

Chapter 2

Advanced Configuration

10

EtherFast Cable/DSL Router with 8-Port Switch

Applications and Gaming > Port Triggering

Port Triggering

Application Enter the application name of the trigger.

Triggered Range

Start Port and End Port For each application, enter

the starting and ending port numbers of the triggered

port number range. Check with the Internet application

documentation for the port number(s) needed.

Forwarded Range

Start Port and End Port For each application, enter

the starting and ending port numbers of the forwarded

port number range. Check with the Internet application

documentation for the port number(s) needed.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Applications and Gaming > UPnP

Forwarding

The UPnP Forwarding screen displays preset application

settings as well as options to customize port services for

other applications.

Applications and Gaming > UPnP Forwarding

UPnP Forwarding

Application

Ten applications are preset. For custom applications,

enter the name of your application in one of the available

fields.

The preset applications are among the most widely used

Internet applications. They include the following:

FTP (File Transfer Protocol) A protocol used to transfer

files over a TCP/IP network (Internet, UNIX, etc.). For

example, after developing the HTML pages for a website

on a local machine, they are typically uploaded to the web

server using FTP.

Telnet A terminal emulation protocol commonly used on

Internet and TCP/IP-based networks. It allows a user at a

terminal or computer to log onto a remote device and run

a program.

SMTP (Simple Mail Transfer Protocol) The standard e-

mail protocol on the Internet. It is a TCP/IP protocol that

defines the message format and the message transfer

agent (MTA), which stores and forwards the mail.

DNS (Domain Name System) The way that Internet

domain names are located and translated into IP addresses.

A domain name is a meaningful and easy-to-remember

“handle” for an Internet address.

TFTP (Trivial File Transfer Protocol) A version of the

TCP/IP FTP protocol that has no directory or password

capability.

Finger A UNIX command widely used on the Internet

to find out information about a particular user, such as a

telephone number, whether the user is currently logged

on, and the last time the user was logged on. The person

Chapter 2

Advanced Configuration

11

EtherFast Cable/DSL Router with 8-Port Switch

being “fingered” must have placed his or her profile on

the system in order for the information to be available.

Fingering requires entering the full user@domain

address.

HTTP (HyperText Transport Protocol) The

communications protocol used to connect to servers on

the World Wide Web. Its primary function is to establish a

connection with a web server and transmit HTML pages to

the client web browser.

POP3 (Post Office Protocol 3) A standard mail server

commonly used on the Internet. It provides a message

store that holds incoming e-mail until users log on and

download it. POP3 is a simple system with little selectivity.

All pending messages and attachments are downloaded at

the same time. POP3 uses the SMTP messaging protocol.

NNTP (Network News Transfer Protocol) The protocol

used to connect to Usenet groups on the Internet. Usenet

newsreaders support the NNTP protocol.

SNMP (Simple Network Management Protocol) A

widely used network monitoring and control protocol.

Data is passed from SNMP agents, which are hardware

and/or software processes reporting activity in each

network device (hub, router, bridge, etc.), to the workstation

console used to oversee the network. The agents return

information contained in a MIB (Management Information

Base), which is a data structure that defines what is

obtainable from the device and what can be controlled

(turned off, on, etc.).

Ext. Port. Enter the number of the external port used by

the server in the Ext. Port column. Check with the Internet

application documentation for more information.

TCP or UDP Select the protocol UDP or TCP for each

application. You cannot select both protocols.

Int. Port Enter the number of the internal port used

by the server in the Int. Port column. Check with the

Internet application software documentation for more

information.

IP Address Enter the IP address of the server that you

want the Internet users to be able to access.

Enabled Select Enabled to enable the service you have

defined.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Applications and Gaming > DMZ

The DMZ feature allows one network computer to be

exposed to the Internet for use of a special-purpose

service such as Internet gaming or videoconferencing.

DMZ hosting forwards all the ports at the same time to

one PC. The Port Range Forwarding feature is more secure

because it only opens the ports you want to have opened,

while DMZ hosting opens all the ports of one computer,

exposing the computer to the Internet.

Applications and Gaming > DMZ

DMZ

Any PC whose port is being forwarded must have its DHCP

client function disabled and should have a new static IP

address assigned to it because its IP address may change

when using the DHCP function.

DMZ To disable DMZ hosting, keep the default, Disable.

To expose one PC, select Enable. Then configure the

following setting:

DMZ Host IP Address Enter the IP address of the

computer you want to expose.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Applications and Gaming > QoS

Quality of Service (QoS) ensures better service to

high-priority types of network traffic, which may

involve demanding, real-time applications, such as

videoconferencing.

Chapter 2

Advanced Configuration

12

EtherFast Cable/DSL Router with 8-Port Switch

Applications and Gaming > QoS

QoS

Enable/Disable To limit outgoing bandwidth for the QoS

policies in use, select Enable. Otherwise, keep the default,

Disable.

Upstream Bandwidth Select the bandwidth to be used

from the drop-down menu. This setting allows you to limit

the outgoing bandwidth for the QoS policies in use, so you

can control how much bandwidth a particular application

is allowed to use.

There are three types of QoS available: Device Priority,

Ethernet Port Priority, and Application Priority.

Device Priority

Device Name Enter the name of your network device.

Priority Select the appropriate priority level.

MAC Address Enter the MAC address of the device.

Ethernet Port Priority

Ethernet Port Priority QoS allows you to prioritize

performance for four of the Router’s ports, LAN Ports

1-4. It does not require support from your ISP because

the prioritized ports are LAN ports going out to your

network.

Priority For each of these ports, select High or Low.

Flow Control If you want the Router to control the

transmission of data between network devices, keep the

default, Enable. To disable this feature, select Disable. The

Router’s other four ports will be automatically assigned

low priority.

Incoming Rate Limit This feature limits the incoming

bandwidth. To use this feature, select 8M, 4M, 2M, 1M,

512K, 256K, or 128K (M stands for Mbps, while K stands

for kbps). If you do not want to use this feature, keep the

default, Disable.

Application Priority

Application Priority QoS manages information as it is

transmitted and received. Depending on the settings of

the QoS screen, this feature will assign information a high

or low priority for the five preset applications and three

additional applications that you specify.

The preset applications are among the most widely used

Internet applications. They include the following:

FTP (File Transfer Protocol) A protocol used to transfer

files over a TCP/IP network (Internet, UNIX, etc.). For

example, after developing the HTML pages for a website

on a local machine, they are typically uploaded to the web

server using FTP.

HTTP (HyperText Transport Protocol) The

communications protocol used to connect to servers on

the World Wide Web. Its primary function is to establish a

connection with a web server and transmit HTML pages to

the client web browser.

Telnet A terminal emulation protocol commonly used on

Internet and TCP/IP-based networks. It allows a user at a

terminal or computer to log onto a remote device and run

a program.

SMTP (Simple Mail Transfer Protocol) The standard

e-mail protocol on the Internet. It is a TCP/IP protocol that

defines the message format and the message transfer

agent (MTA), which stores and forwards the mail.

POP3 (Post Office Protocol 3) A standard mail server

commonly used on the Internet. It provides a message

store that holds incoming e-mail until users log on and

download it. POP3 is a simple system with little selectivity.

All pending messages and attachments are downloaded at

the same time. POP3 uses the SMTP messaging protocol.

Application Name Enter the name of an application you

specify.

Priority For each application, select High or Low.

Specific Port# Enter the port number of each application

you specify.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Administration > Management

The Management screen allows the network’s administrator

to manage specific Router functions for access and

security.

Chapter 2

Advanced Configuration

13

EtherFast Cable/DSL Router with 8-Port Switch

Administration > Management

Router Access

Local Router Access

To ensure the Router’s security, you will be asked for your

password when you access the Router’s web-based utility.

The default is admin.

Router Password Enter a new password for the Router.

Re-enter to confirm Enter the password again to

confirm.

Remote Router Access

Remote Upgrade If you want to be able to upgrade the

Router remotely, from outside the local network, select

Enabled. (You must have the Remote Administration

feature enabled as well.) Otherwise, keep the default,

Disabled.

Remote Administration To permit remote access of the

Router, from outside the local network, select Enabled.

Otherwise, keep the default, Disabled.

Administration Port Enter the port number that will be

open to outside access.

NOTE: When you are in a remote location

and wish to manage the Router, enter

http://<Internet_IP_address>:port,

depending on whether you use HTTP or HTTPS.

Enter the Router’s specific Internet IP address

in place of <Internet_IP_address>, and enter

the Administration Port number in place of the

word port.

UPnP

Universal Plug and Play (UPnP) allows Windows Me and XP

to automatically configure the Router for various Internet

applications, such as gaming and videoconferencing.

UPnP If you want to use UPnP, keep the default setting,

Enabled. Otherwise, select Disabled.

Allow Users to Make Configuration Changes Keep the

default, Enabled, if you want to be able to make manual

changes to the Router while using the UPnP feature.

Otherwise, select Disabled.

Allow Users to Disable Internet Access Keep the default,

Enabled, if you want to be able to prohibit any and all

Internet connections. Otherwise, select Disabled.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Administration > Log

The Router can keep logs of all traffic for your Internet

connection.

Administration > Log

Log

Log To disable the Log function, keep the default setting,

No. To monitor traffic between the network and the

Internet, select Yes. With logging enabled, you can choose

to view temporary logs or keep a permanent record using

the Logviewer software.

Logviewer IP Address For a permanent record of these

logs, the Logviewer software must be used. Download

this software from the Linksys website, www.linksys.com.

The Logviewer software saves all incoming and outgoing

activity in a permanent file on your computer’s hard drive.

Enter the fixed IP address of the computer running the

Logviewer software. The Router will now send updated

logs to that computer.

Incoming Log Click this button to view a temporary log

of the Source IP addresses and Destination Port Numbers

for all the incoming Internet traffic. Click Refresh to

update the log.

Outgoing Log Click this button to view a temporary

log of all the URLs and IP addresses of Internet sites that

users on your network have accessed. The LAN IP address,

Chapter 2

Advanced Configuration

14

EtherFast Cable/DSL Router with 8-Port Switch

Destination URL/IP, and Service/Port Number for each site

are listed. Click Refresh to update the log.

View Log Click this button to view a log of all activities

and to access a drop-down menu of various logs to view.

On the All screen, select the log you wish to view: All,

System Log, or Access Log.

Log > View Log

All • You see a log of all activities, a combination of the

System and Access Logs.

System Log • This log displays a list of cold and warm

starts, web login successes and failures, and packet

filtering policies.

Access Log • This log shows all data traffic.

Click Clear to clear a log. Click Refresh to update a

log.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Administration > Factory Defaults

The Administration > Factory Defaults screen allows you

to restore the Router’s configuration to its factory default

settings.

Administration > Factory Defaults

NOTE: Do not restore the factory defaults unless

you are having difficulties with the Router and

have exhausted all other troubleshooting

measures. Once the Router is reset, you will have

to re-enter all of your configuration settings.

Factory Defaults

Restore Factory Defaults To reset the Router’s settings

to the default values, select Yes and click Save Settings.

Then follow the on-screen instructions. Any settings you

have saved will be lost when the default settings are

restored.

Administration > Firmware Upgrade

The Firmware Upgrade screen allows you to upgrade the

Router’s firmware. Do not upgrade the firmware unless

you are experiencing problems with the Router or the new

firmware has a feature you want to use.

Administration > Firmware Upgrade

NOTE: The Router may lose the settings you

have customized. Before you upgrade its

firmware, write down all of your custom settings.

After you upgrade its firmware, you will have to

re-enter all of your configuration settings.

Upgrade Firmware

Before upgrading the firmware, download the Router’s

firmware upgrade file from the Linksys website,

www.linksys.com. Then extract the file.

Please select a file to upgrade Click Browse and select

the extracted firmware upgrade file.

Upgrade After you have selected the appropriate file,

click this button, and f

ollow the on-screen instructions.

Chapter 2

Advanced Configuration

15

EtherFast Cable/DSL Router with 8-Port Switch

Status > Router

The Router screen displays information about the Router

and its current settings.

Status > Router

Information

Firmware Version This is the version number of the

Router’s current firmware.

MAC Address This is the Router’s MAC address, as seen

by your ISP.

Status

This section shows the current network information

stored in the Router. The information varies depending on

the Internet connection type selected on the Basic Setup

screen.

Click Refresh to update the on-screen information.

Status > Local Network

The Local Network screen displays information about the

local, wired network.

Status > Local Network

Local Network

Local MAC Address The MAC address of the Router’s

local, wired interface is displayed here.

IP Address This shows the Router’s IP address, as it

appears on your local network.

Subnet Mask This shows the subnet mask of the Router.

DHCP Server The status of the Router’s DHCP server

function is displayed here.

DHCP Clients Table Click this button to view a list of PCs

that are using the Router as a DHCP server.

DHCP Clients Table

DHCP Client Table

The DHCP Client Table lists computers and other

devices that have been assigned IP addresses by the

Router. The DHCP Server IP Address is the IP address

of the Router. The table lists the Client Hostname, IP

Address, MAC Address, and Interface for each DHCP

client. To remove a DHCP client, select the client

and click Delete. To retrieve the most up-to-date

information, click Refresh.

Click Refresh to update the on-screen information.

Appendix A

Troubleshooting

16

EtherFast Cable/DSL Router with 8-Port Switch

Appendix A:

Troubleshooting

Your computer cannot connect to the Internet.

Follow these instructions until your computer can connect

to the Internet:

Make sure that the Router is powered on. The Power •

LED should be green and not flashing.

If the Power LED is flashing, then power off all of •

your network devices, including the modem, Router,

and computers. Then power on each device in the

following order:

Cable or DSL modem1.

Router2.

Computer3.

Check the cable connections. The computer should •

be connected to one of the ports numbered 1-4 on

the Router, and the modem must be connected to the

Internet port on the Router.

The modem does not have an Ethernet port.

The modem is a dial-up modem for traditional dial-up

service. To use the Router, you need a cable/DSL modem

and high-speed Internet connection.

You cannot use the DSL service to connect manually to

the Internet.

After you have installed the Router, it will automatically

connect to your Internet Service Provider (ISP), so you no

longer need to connect manually.

The DSL telephone line does not t into the Router’s

Internet port.

The Router does not replace your modem. You still need

your DSL modem in order to use the Router. Connect

the telephone line to the DSL modem, insert the setup

CD into your computer, and then follow the on-screen

instructions.

When you double-click the web browser, you are

prompted for a username and password. If you want to

get rid of the prompt, follow these instructions.

Launch the web browser and perform the following steps

(these steps are specific to Internet Explorer but are similar

for other browsers):

Select 1. Tools > Internet Options.

Click the 2. Connections tab.

Select 3. Never dial a connection.

Click 4. OK.

The Router does not have a coaxial port for the cable

connection.

The Router does not replace your modem. You still need

your cable modem in order to use the Router. Connect your

cable connection to the cable modem, insert the setup

CD into your computer, and then follow the on-screen

instructions.

You need to modify the settings on the Router.

Open the web browser (for example, Internet Explorer or

Firefox), and enter the Router’s IP address in the address

field (the default IP address is 192.168.1.1). When

prompted, leave the User name field blank and enter the

password to the Router (the default is admin). Click the

appropriate tab to change the settings.

WEB: If your questions are not addressed here,

refer to the Linksys website, www.linksys.com.

Appendix B

Specifications

17

EtherFast Cable/DSL Router with 8-Port Switch

Appendix B:

Specifications

Model BEFSR81

Standards IEEE 802.3 (10BaseT), 802.3u

(100BaseTX)

Ports One 10/100 RJ-45 Port for

Broadband Modem

Eight 10/100 RJ-45 Switched Ports

Button Reset

Cabling Type Ethernet Category 5

LEDs Power, QoS, Ethernet, Internet

OS Support Windows 98SE/Me/2000/XP/Vista

Network Protocols TCP/IP

Environmental

Dimensions 7.31" x 6.06" x 1.89"

(186 x 154 x 48 mm)

Unit Weight 12.30 oz. (350 g)

Power External, 12V DC, 1A

Certications FCC, CE

Operating Temp. 32 to 104ºF (0 to 40ºC)

Storage Temp. -4 to 158ºF (-20 to 70ºC)

Operating Humidity 10% to 85%, Noncondensing

Storage Humidity 5% to 90%, Noncondensing

Specications are subject to change without notice.

Page is loading ...

Cisco Systems BEFSR81 User manual

This manual is also suitable for

Cisco Systems BEFSR81 User manual

Related papers

Other documents