XD1222

Dual XD1222, CP1222 User manual

  • Hello! I am an AI chatbot trained to assist you with the Dual XD1222 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
AM/FM/CD Receiver with Auxiliary Input, USB Charging Port and
Detachable Face
XD1222
Charge Port
INSTALLATION/OWNER'S MANUAL
2
Preparation
KEYS
HEX BOLT
MOUNTING SLEEVE
PLAIN WASHER
HEX NUT
MOUNTING STRAP
TYPICAL MOUNTING METHOD
XD1222INSTALLATION
Please read entire manual before installation.
Before You Start
•Disconnectnegativebatteryterminal.Consultaqualifiedtechnicianforinstructions.
•Avoidinstallingtheunitwhereitwouldbesubjecttohightemperatures,suchasfrom
directsunlight,orwhereitwouldbesubjecttodust,dirtorexcessivevibration.
Getting Started
•Remove2transitscrewslocatedontopoftheunit.
•Insertthesuppliedkeysintotheslotsasshown,andslidetheunitoutofthemounting
sleeve.
•Installmountingsleeveintoopening,bendingtabstosecure.
•Connectwiringharnessandantenna.Consultaqualifiedtechnicianifyouareunsure.
•Certainvehiclesmayrequireaninstallationkitand/orwiringharnessadapter(sold
separately).
•Testforcorrectoperationandslideinto
mounting sleeve to secure.
•Snaptrimringintoplace.
3
Rear Preamp Output
Connect to amplifier RCA input
Antenna Connector
RCA Cable
(sold separately)
AMP
BLUE
BLACK
RED
YELLOW
Remote Turn-On
Connect to amplifier or power
antenna. Insulate wire if not used.
Ground
Connect to vehicle
chassis ground.
Accessory
Connect to ignition
circuit or switched 12 volt source.
Memory
Connect to battery
circuit or constant 12 volt source.
Right Front
Gray/Black (-)
Gray (+)
Left Front
White/Black (-)
White (+)
Right Rear
Violet/Black (-)
Violet (+)
Left Rear
Green/Black (-)
Green (+)
5 AMP
AGC Fuse
Wiring Diagram
FUSE
When replacing the fuse,
makesurenewfuseisthe
correct type and amperage.
Using an incorrect fuse
could damage the radio.
TheXD1222usesone5amp
AGC fuse located in-line.
* Caution-Donotattachanyspeakerleadstogroundasseveredamagewilloccur.
XD1222INSTALLATION
4
Control Locations
Release
Mode
Power
Rotary Encoder
Preset 4/Play/Pause
Preset1/Repeat
Preset5
Preset 2/Random
Preset 3/Intro
Preset 6
1
2
3
4
5
6
7
8
9
10
Tune/TrackDown
Eject
Tune/TrackUp
EQ/Stereo/Mono
Auxiliary Input
Audio/Loudness
USB Charge
AS/PS
Band
Display
11
12
13
14
15
16
17
18
19
17 16
1
2 3 8
19 18
XD1222OPERATION
TheXD1222hasaneasy-to-useinterfacethatprovidesarewardingexperience,as
wellassupportforyourfavoritetunes.AudioCD-RandCD-RWdiscplaybackensures
compatibility with your music collection, and the RCA preamp output provides the right
connections to expand your system. From its front panel auxiliary input for connecting your
MP3 player, to the detachable face for security assurance, this head unit has you covered.
4 65 119 12 137 10
141520
20
5
General Operation
Press RELEASE and pull away from the left side to remove.
Tore-install,insertrightsideoffaceplatefirstthenpushleft
side to secure.
Removetrimringandinstallsupplied#1x7/32”Phillipshead
screw through left side of mounting frame into faceplate.
Press PWR to turn the unit on. Inserting a CD will turn the
unit on automatically. Press PWR to turn the unit off.
Press MODE to select between AM/FM, CD or auxiliary input.
Modes of operation are indicated in the display.
Press and hold LOUD for 2 seconds to activate and deactivate
the loud feature. Activating this feature will enhance the
bassandtreblefrequencieswhenlisteningtomusicatlow
volumes.
Inserta3.5mmconnectorinthefrontpanelAUXport.
Connecttheotherendofthe3.5mmconnectortothe
headphone output of an audio device, MP3 player, etc. Press
MODEtoselectAUXmode.
Adjustvolumeusingtherotary encoder(00-46).
Press DISPtodisplaytheclock.Theradiofrequency(tuner
mode)andCDtrack/elapsedtime(CDplayermode)willbe
shown by default.
Press DISPtodisplaytheclock,thenrelease.Pressand
hold DISPfor2seconds,theclockwillbegintoflash.Press
TRACK
nn
toadjustthehoursandTRACK 
ll
toadjust
theminutes.Clocksettingswillbesavedafter5seconds.
Theclockwilldisplay12-hourAM/PMtimeinUSAfrequency
spacingmode(PM10:00).InEuropeanfrequencyspacing
mode,theclockwilldisplay24-hourtime(22:00).
Press and hold for more than 2 seconds to RESET the unit
uponinitialinstallation.TheRESET button is located behind
the faceplate.
Faceplate Removal
Semi-permanent Faceplate 
Installation
Power On/Off
Mode
Loud
Auxiliary Input
Volume
Display
Set the Clock
12/24-hour Clock 
Reset
XD1222OPERATION
6
General Operation
Insert the USB connector of a battery powered USB device
into the USB charging port on the front panel, which
provides5voltsDCand1.0amps.TheUSBdevicewill
immediately begin charging.
Note:TheUSBchargingportmaynotbecompatiblewith
everydeviceduetodifferencesinpowerrequirements.
Note:ThisUSBportprovidespoweronly,andwillnot
playbackmusicfromaUSBdevice.
Press AUDIOtoselectbetweenVolume(default),Bass,
Treble,Balance&Fader.
Press AUDIO until BA appears
Rotate the rotary encoderleft/righttoadjust
(-6minimum/6maximum)
Press AUDIOuntilTRappears
Rotate the rotary encoderleft/righttoadjust
(-6minimum/6maximum)
Press AUDIO until B appears
Rotate the rotary encoderleft/righttoadjust
(BL15/BR15)B00representsequalbalance.
Press AUDIO until F appears
Rotate the rotary encoderleft/righttoadjust
(FF15/FR15)F00representsequalbalance.
Press EQ to select between CLS, POP, ROC and OFF
(default)equalizationcurves.AnyadjustmenttotheBassor
TreblesettingsautomaticallycancelsthecurrentEQcurve.
USB Charging Port
Select Audio
Bass
Treble
Balance
Fader
Preset EQ Curves
BASSVOLUME TREBLE BALANCE FADER
XD1222OPERATION
7
Tuner Operation
Press TUNE
nn
or TUNE 
ll
momentarilytoseekthe
next strong station.
Press TUNE
nn
or TUNE 
ll
for more than 2 seconds,
thenrelease.“MANU”willmomentarilyappearinthedisplay.
Press TUNE
nn
or TUNE 
ll
momentarily to move radio
frequencyupordownonestepatatime.Pressandholdto
advancequickly.Iftuningisnotadjustedfor5seconds,the
unitwillreturntoseektuningmode(default).“AUTO”will
momentarily appear in the display.
Press ST/MO for more than 2 seconds during FM tuner
operationtoselectmonoorstereo(default)receptionofthe
broadcast signal.
Press BANDtoselectbetweenFM1,FM2,FM3andAM1,AM2
bands.
Press and hold BAND then press TUNE
nn
to select
Europeanfrequencyspacing.PressandholdBAND then
press TUNE 
ll
toselectUSAfrequencyspacing(default).
Anytimefrequencyspacingischanged,allstationpresets
are erased.
Upto18FMstationsand12AMstationscanbestored.
Tostoreastation,selectthedesiredbandandstation.
Press and hold the desired preset button for more than 2
seconds. When stored, the preset number will appear in the
display.Thestationcanberecalledanytimebypressingthe
corresponding preset button.
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band.
Press AS/PSmomentarilytoscanpresets1-6onthecurrent
band,pausingfor5secondsateach.PressAS/PS again to
cancel.
Seek Tuning
Manual Tuning
FM Stereo/Mono
Band
Frequency Spacing
Storing and Recalling 
Station Presets
Automatically Store 
Stations
Preset Scan
XD1222OPERATION
8
CD Player Operation
Withthelabelfacingup,insertastandardsizeCDintothe
CDslot.TheCDwillautomaticallybeginplayback.
Press the EJECTbuttontostopandejecttheCD.
Theunitwillchangetotunermode.
Press TRACK 
ll
toskiptothebeginningofthenexttrack.
Press TRACK
nn
to return to the beginning of the current
track.PressingTRACK
nn
againskipstothebeginningof
theprevioustrack.
Press and hold TRACK 
ll
or TRACK
nn
to fast forward
orreverseatrack.
Press
l
/
II
totemporarilystopCDplayback.
Press
l
/
II
againtoresumeplayback.
Press INTtoplaythefirst10secondsofeachtrack.
Press INT to cancel.
Press RPTtocontinuouslyrepeatselectedtrack.
Press RPT to cancel.
Press RDMtoplayalltracksinrandomorder.
Press RDM again to cancel.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method.
Note:CD-Rrecordingsessionsmustbeclosed(finalized)for
playback.
Insert CD
Eject CD
Track Select
Fast Forward and Reverse
Pause
Intro
Repeat
Random
CD-R/CD-RW 
Compatibility
XD1222OPERATION
9
Troubleshooting
Problem Cause Action
Yellow wire not connected or incorrect voltage
Red wire not connected or incorrect voltage
Checkconnectionsforpropervoltage
(11~16VDC)
Blackwirenotconnected Checkconnectiontoground
Fuse blown Replace fuse
Speakerwiresnotconnected Checkconnectionsatspeakers
Oneormorespeakerwirestouchingeach
other or touching chassis ground
Insulateallbarespeakerwiresfrom
each other and chassis ground
Yellow or red wire touching chassis ground Checkforpinchedwire
Speakerwirestouchingchassisground Checkforpinchedwire
Incorrect fuse rating Use fuse with correct rating
Unitisnotmountedcorrectlyorbackstrapis
not secure
CD mechanism position out of alignment
CD transit screws still in place
Checkmountingsleeveandbackstrap
support
Physicaldefectinmedia(CD,CD-RorCD-
RW) Checkmediaforscratches
PressEJECTfor3secondstoreset
CD mechanism position
Remove 2 transit screws located on top
of the unit.
Unit will not turn on
(nopower)
Unit has power
(butnosound)
Unit blows fuses
Excessiveskipping
Unit will not accept
a disc
Error Codes
Error Code Cause Action
ER-1appearsondisplay Disc error PressejectorRESET
ER-2 appears on display Mechanism error PressejectorRESET
ER-3 appears on display Servo error or disc is in upside down PressejectorRESET
XD1222OPERATION
10
Limited One Year Warranty
Thiswarrantygivesyouspecificlegalrights.
You may also have other rights which vary from
state to state.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
materialandworkmanshipforaperiodofone
year from the date of the original purchase.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
inmaterialorworkmanshiportofurnishan
equalnew,renewedorcomparableproduct
(whicheverisdeemednecessary)inexchange
withoutcharges,subjecttoverificationofthe
defect or malfunction and proof of the date of
purchase.Subsequentreplacementproducts
are warranted for the balance of the original
warranty period.
Who is covered? Thiswarrantyisextendedto
the original retail purchaser for products
purchased and used in the U.S.A.
What is covered? Thiswarrantycoversall
defectsinmaterialandworkmanshipinthis
product.Thefollowingarenotcovered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
linevoltage,unauthorizedrepairorfailureto
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
What to do?
1.Beforeyoucallforservice,checkthe
troubleshooting guide in your owner’s
manual.Aslightadjustmentofanycustom
controls may save you a service call.
2.Ifyourequireserviceduringthewarranty
period,youmustcarefullypacktheproduct
(preferablyintheoriginalpackage)andship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorizedservicecenter.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address(P.O.Boxnotacceptable),anda
daytime phone number with your shipment.
4. For more information and for the location of
thenearestauthorizedservicecenterplease
contactusbyoneofthefollowingmethods:
•Callustoll-freeat1-866-382-5476
•E-mailusat[email protected]
ExclusionofCertainDamages:Thiswarranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
isauthorizedtoassumeforthecompanyany
other liability in connection with the sale of
this product. In no event shall the company be
liableforindirect,incidentalorconsequential
damages.
XD1222WARRANTY
11
XD1222NOTES
Specifications
Frequencyresponse:20Hz-20kHz
Channelseparation@1kHz:>65dB
D/Aconverter:1Bit
Tuningrange:87.5MHz-107.9MHz
Usablesensitivity:12dBf
50dBquietingsensitivity:16dBf
Stereoseparation@1kHz:40dB
Frequencyresponse:30Hz-13kHz
Tuningrange:530kHz-1710kHz
Usablesensitivity:30uV
Frequencyresponse:80Hz-2kHz
Operatingvoltage:11-16VDC,negativeground
Speakeroutputimpedance:4~8ohms
Fuse:5ampAGC
Dimensions:7"x7"x2"(178x178x51mm)
Designandspecificationssubjecttochangewithoutnotice.
CD Player
FMTuner
AMTuner
General
CEA-2006 Power Standard Specifications
(reference:14.4VDC+/-0.2V,20Hz~20kHz)
PowerOutput:5WattsRMSx4channelsat4ohmsand<1%THD+N
Signaltonoiseratio:75dBA(reference:1wattinto4ohms)
Dual Electronics Corp.
TollFree:1-866-382-5476
www.dualav.com
©2008DualElectronicsCorp.Allrightsreserved.
NSA0608-V01
/