Dual CP1222 User manual

Brand: Dual

Model: CP1222

Category: Car media receivers

Type: User manual

This manual is also suitable for

XD1222

AM/FM/CD Receiver with Auxiliary Input, USB Charging Port and

Detachable Face

XD1222

Charge Port

INSTALLATION/OWNER'S MANUAL

Preparation

KEYS

HEX BOLT

MOUNTING SLEEVE

PLAIN WASHER

HEX NUT

MOUNTING STRAP

TYPICAL MOUNTING METHOD

XD1222 INSTALLATION

Please read entire manual before installation.

Before You Start

•Disconnectnegativebatteryterminal.Consultaqualifiedtechnicianforinstructions.

•Avoidinstallingtheunitwhereitwouldbesubjecttohightemperatures,suchasfrom

directsunlight,orwhereitwouldbesubjecttodust,dirtorexcessivevibration.

Getting Started

•Remove2transitscrewslocatedontopoftheunit.

•Insertthesuppliedkeysintotheslotsasshown,andslidetheunitoutofthemounting

sleeve.

•Installmountingsleeveintoopening,bendingtabstosecure.

•Connectwiringharnessandantenna.Consultaqualifiedtechnicianifyouareunsure.

•Certainvehiclesmayrequireaninstallationkitand/orwiringharnessadapter(sold

separately).

•Testforcorrectoperationandslideinto

mounting sleeve to secure.

•Snaptrimringintoplace.

Rear Preamp Output

Connect to amplifier RCA input

Antenna Connector

RCA Cable

(sold separately)

AMP

BLUE

BLACK

RED

YELLOW

Remote Turn-On

Connect to amplifier or power

antenna. Insulate wire if not used.

Ground

Connect to vehicle

chassis ground.

Accessory

Connect to ignition

circuit or switched 12 volt source.

Memory

Connect to battery

circuit or constant 12 volt source.

Right Front

Gray/Black (-)

Gray (+)

Left Front

White/Black (-)

White (+)

Right Rear

Violet/Black (-)

Violet (+)

Left Rear

Green/Black (-)

Green (+)

5 AMP

AGC Fuse

Wiring Diagram

FUSE

When replacing the fuse,

makesurenewfuseisthe

correct type and amperage.

Using an incorrect fuse

could damage the radio.

TheXD1222usesone5amp

AGC fuse located in-line.

* Caution-Donotattachanyspeakerleadstogroundasseveredamagewilloccur.

XD1222 INSTALLATION

Control Locations

Release

Mode

Power

Rotary Encoder

Preset 4/Play/Pause

Preset1/Repeat

Preset5

Preset 2/Random

Preset 3/Intro

Preset 6

Tune/TrackDown

Eject

Tune/TrackUp

EQ/Stereo/Mono

Auxiliary Input

Audio/Loudness

USB Charge

AS/PS

Band

Display

17 16

2 3 8

19 18

XD1222 OPERATION

TheXD1222hasaneasy-to-useinterfacethatprovidesarewardingexperience,as

wellassupportforyourfavoritetunes.AudioCD-RandCD-RWdiscplaybackensures

compatibility with your music collection, and the RCA preamp output provides the right

connections to expand your system. From its front panel auxiliary input for connecting your

MP3 player, to the detachable face for security assurance, this head unit has you covered.

4 65 119 12 137 10

141520

General Operation

Press RELEASE and pull away from the left side to remove.

Tore-install,insertrightsideoffaceplatefirstthenpushleft

side to secure.

Removetrimringandinstallsupplied#1x7/32”Phillipshead

screw through left side of mounting frame into faceplate.

Press PWR to turn the unit on. Inserting a CD will turn the

unit on automatically. Press PWR to turn the unit off.

Press MODE to select between AM/FM, CD or auxiliary input.

Modes of operation are indicated in the display.

Press and hold LOUD for 2 seconds to activate and deactivate

the loud feature. Activating this feature will enhance the

bassandtreblefrequencieswhenlisteningtomusicatlow

volumes.

Inserta3.5mmconnectorinthefrontpanelAUXport.

Connecttheotherendofthe3.5mmconnectortothe

headphone output of an audio device, MP3 player, etc. Press

MODEtoselectAUXmode.

Adjustvolumeusingthe rotary encoder(00-46).

Press DISPtodisplaytheclock.Theradiofrequency(tuner

mode)andCDtrack/elapsedtime(CDplayermode)willbe

shown by default.

Press DISPtodisplaytheclock,thenrelease.Pressand

hold DISPfor2seconds,theclockwillbegintoflash.Press

TRACK

toadjustthehoursandTRACK

toadjust

theminutes.Clocksettingswillbesavedafter5seconds.

Theclockwilldisplay12-hourAM/PMtimeinUSAfrequency

spacingmode(PM10:00).InEuropeanfrequencyspacing

mode,theclockwilldisplay24-hourtime(22:00).

Press and hold for more than 2 seconds to RESET the unit

uponinitialinstallation.TheRESET button is located behind

the faceplate.

Faceplate Removal

Semi-permanent Faceplate

Installation

Power On/Off

Mode

Loud

Auxiliary Input

Volume

Display

Set the Clock

12/24-hour Clock

Reset

XD1222 OPERATION

General Operation

Insert the USB connector of a battery powered USB device

into the USB charging port on the front panel, which

provides5voltsDCand1.0amps.TheUSBdevicewill

immediately begin charging.

Note:TheUSBchargingportmaynotbecompatiblewith

everydeviceduetodifferencesinpowerrequirements.

Note:ThisUSBportprovidespoweronly,andwillnot

playbackmusicfromaUSBdevice.

Press AUDIOtoselectbetweenVolume(default),Bass,

Treble,Balance&Fader.

Press AUDIO until BA appears

Rotate the rotary encoderleft/righttoadjust

(-6minimum/6maximum)

Press AUDIOuntilTRappears

Rotate the rotary encoderleft/righttoadjust

(-6minimum/6maximum)

Press AUDIO until B appears

Rotate the rotary encoderleft/righttoadjust

(BL15/BR15)B00representsequalbalance.

Press AUDIO until F appears

Rotate the rotary encoderleft/righttoadjust

(FF15/FR15)F00representsequalbalance.

Press EQ to select between CLS, POP, ROC and OFF

(default)equalizationcurves.AnyadjustmenttotheBassor

TreblesettingsautomaticallycancelsthecurrentEQcurve.

USB Charging Port

Select Audio

Bass

Treble

Balance

Fader

Preset EQ Curves

BASSVOLUME TREBLE BALANCE FADER

XD1222 OPERATION

Tuner Operation

Press TUNE

or TUNE

momentarilytoseekthe

next strong station.

Press TUNE

or TUNE

for more than 2 seconds,

thenrelease.“MANU”willmomentarilyappearinthedisplay.

Press TUNE

or TUNE

momentarily to move radio

frequencyupordownonestepatatime.Pressandholdto

advancequickly.Iftuningisnotadjustedfor5seconds,the

unitwillreturntoseektuningmode(default).“AUTO”will

momentarily appear in the display.

Press ST/MO for more than 2 seconds during FM tuner

operationtoselectmonoorstereo(default)receptionofthe

broadcast signal.

Press BANDtoselectbetweenFM1,FM2,FM3andAM1,AM2

bands.

Press and hold BAND then press TUNE

to select

Europeanfrequencyspacing.PressandholdBAND then

press TUNE

toselectUSAfrequencyspacing(default).

Anytimefrequencyspacingischanged,allstationpresets

are erased.

Upto18FMstationsand12AMstationscanbestored.

Tostoreastation,selectthedesiredbandandstation.

Press and hold the desired preset button for more than 2

seconds. When stored, the preset number will appear in the

display.Thestationcanberecalledanytimebypressingthe

corresponding preset button.

Press AS/PS for more than 2 seconds to automatically store

the six strongest stations in the current band.

Press AS/PSmomentarilytoscanpresets1-6onthecurrent

band,pausingfor5secondsateach.PressAS/PS again to

cancel.

Seek Tuning

Manual Tuning

FM Stereo/Mono

Band

Frequency Spacing

Storing and Recalling

Station Presets

Automatically Store

Stations

Preset Scan

XD1222 OPERATION

CD Player Operation

Withthelabelfacingup,insertastandardsizeCDintothe

CDslot.TheCDwillautomaticallybeginplayback.

Press the EJECTbuttontostopandejecttheCD.

Theunitwillchangetotunermode.

Press TRACK

toskiptothebeginningofthenexttrack.

Press TRACK

to return to the beginning of the current

track.PressingTRACK

againskipstothebeginningof

theprevioustrack.

Press and hold TRACK

or TRACK

to fast forward

orreverseatrack.

Press

totemporarilystopCDplayback.

Press

againtoresumeplayback.

Press INTtoplaythefirst10secondsofeachtrack.

Press INT to cancel.

Press RPTtocontinuouslyrepeatselectedtrack.

Press RPT to cancel.

Press RDMtoplayalltracksinrandomorder.

Press RDM again to cancel.

Some CD-Rs and CD-RWs may be incompatible with this

unit, depending on media type and recording method.

Note:CD-Rrecordingsessionsmustbeclosed(finalized)for

playback.

Insert CD

Eject CD

Track Select

Fast Forward and Reverse

Pause

Intro

Repeat

Random

CD-R/CD-RW

Compatibility

XD1222 OPERATION

Troubleshooting

Problem Cause Action

Yellow wire not connected or incorrect voltage

Red wire not connected or incorrect voltage

Checkconnectionsforpropervoltage

(11~16VDC)

Blackwirenotconnected Checkconnectiontoground

Fuse blown Replace fuse

Speakerwiresnotconnected Checkconnectionsatspeakers

Oneormorespeakerwirestouchingeach

other or touching chassis ground

Insulateallbarespeakerwiresfrom

each other and chassis ground

Yellow or red wire touching chassis ground Checkforpinchedwire

Speakerwirestouchingchassisground Checkforpinchedwire

Incorrect fuse rating Use fuse with correct rating

Unitisnotmountedcorrectlyorbackstrapis

not secure

CD mechanism position out of alignment

CD transit screws still in place

Checkmountingsleeveandbackstrap

support

Physicaldefectinmedia(CD,CD-RorCD-

RW) Checkmediaforscratches

PressEJECTfor3secondstoreset

CD mechanism position

Remove 2 transit screws located on top

of the unit.

Unit will not turn on

(nopower)

Unit has power

(butnosound)

Unit blows fuses

Excessiveskipping

Unit will not accept

a disc

Error Codes

Error Code Cause Action

ER-1appearsondisplay Disc error PressejectorRESET

ER-2 appears on display Mechanism error PressejectorRESET

ER-3 appears on display Servo error or disc is in upside down PressejectorRESET

XD1222 OPERATION

Limited One Year Warranty

Thiswarrantygivesyouspecificlegalrights.

You may also have other rights which vary from

state to state.

Dual Electronics Corp. warrants this product to

the original purchaser to be free from defects in

materialandworkmanshipforaperiodofone

year from the date of the original purchase.

Dual Electronics Corp. agrees, at our option,

during the warranty period, to repair any defect

inmaterialorworkmanshiportofurnishan

equalnew,renewedorcomparableproduct

(whicheverisdeemednecessary)inexchange

withoutcharges,subjecttoverificationofthe

defect or malfunction and proof of the date of

purchase.Subsequentreplacementproducts

are warranted for the balance of the original

warranty period.

Who is covered? Thiswarrantyisextendedto

the original retail purchaser for products

purchased and used in the U.S.A.

What is covered? Thiswarrantycoversall

defectsinmaterialandworkmanshipinthis

product.Thefollowingarenotcovered:

installation/removal costs, damage resulting

from accident, misuse, abuse, neglect, product

modification, improper installation, incorrect

linevoltage,unauthorizedrepairorfailureto

follow instructions supplied with the product,

or damage occurring during return shipment of

the product.

What to do?

1.Beforeyoucallforservice,checkthe

troubleshooting guide in your owner’s

manual.Aslightadjustmentofanycustom

controls may save you a service call.

2.Ifyourequireserviceduringthewarranty

period,youmustcarefullypacktheproduct

(preferablyintheoriginalpackage)andship

it by prepaid transportation with a copy of the

original receipt from the retailer to an

authorizedservicecenter.

3. Please describe your problem in writing and

include your name, a return UPS shipping

address(P.O.Boxnotacceptable),anda

daytime phone number with your shipment.

4. For more information and for the location of

thenearestauthorizedservicecenterplease

contactusbyoneofthefollowingmethods:

•Callustoll-freeat1-866-382-5476

•E-mailusat[email protected]

ExclusionofCertainDamages:Thiswarranty

is exclusive and in lieu of any and all other

warranties, expressed or implied, including

without limitation the implied warranties of

merchantability and fitness for a particular

purpose and any obligation, liability, right,

claim or remedy in contract or tort, whether

or not arising from the company’s negligence,

actual or imputed. No person or representative

isauthorizedtoassumeforthecompanyany

other liability in connection with the sale of

this product. In no event shall the company be

liableforindirect,incidentalorconsequential

damages.

XD1222 WARRANTY

XD1222 NOTES

Specifications

Frequencyresponse:20Hz-20kHz

Channelseparation@1kHz:>65dB

D/Aconverter:1Bit

Tuningrange:87.5MHz-107.9MHz

Usablesensitivity:12dBf

50dBquietingsensitivity:16dBf

Stereoseparation@1kHz:40dB

Frequencyresponse:30Hz-13kHz

Tuningrange:530kHz-1710kHz

Usablesensitivity:30uV

Frequencyresponse:80Hz-2kHz

Operatingvoltage:11-16VDC,negativeground

Speakeroutputimpedance:4~8ohms

Fuse:5ampAGC

Dimensions:7"x7"x2"(178x178x51mm)

Designandspecificationssubjecttochangewithoutnotice.

CD Player

FMTuner

AMTuner

General

CEA-2006 Power Standard Specifications

(reference:14.4VDC+/-0.2V,20Hz~20kHz)

PowerOutput:5WattsRMSx4channelsat4ohmsand<1%THD+N

Signaltonoiseratio:75dBA(reference:1wattinto4ohms)

Dual Electronics Corp.

TollFree:1-866-382-5476

www.dualav.com

NSA0608-V01

Dual CP1222 User manual

Brand: Dual

Model: CP1222

Category: Car media receivers

Type: User manual

This manual is also suitable for

XD1222

Download PDF

report

Dual CP1222 User manual

This manual is also suitable for

Dual CP1222 User manual

Related papers

Other documents