Metra 99-5600 Installation guide

Metra
Brand
Metra
Model
99-5600
Category
Mounting kits
Type
Installation guide

This manual is also suitable for

Metra Electronics 99-5600 is a car stereo installation kit designed to fit a variety of Ford, Lincoln, and Mercury vehicles. It includes a radio housing, equalizer, dummy plate, and rear support bracket. The kit allows you to install a 2-shaft or DIN head unit in your vehicle.

The 99-5600 kit is easy to install. Simply remove your factory head unit and disconnect the wiring. Then, slide the aftermarket head unit into the kit and secure it with the shaft nuts or DIN cage. If you are installing an equalizer, slide it into the back of the radio housing and secure it. If you are not installing an equalizer, snap the equalizer dummy plate into the opening.

Metra Electronics 99-5600 is a car stereo installation kit designed to fit a variety of Ford, Lincoln, and Mercury vehicles. It includes a radio housing, equalizer, dummy plate, and rear support bracket. The kit allows you to install a 2-shaft or DIN head unit in your vehicle.

The 99-5600 kit is easy to install. Simply remove your factory head unit and disconnect the wiring. Then, slide the aftermarket head unit into the kit and secure it with the shaft nuts or DIN cage. If you are installing an equalizer, slide it into the back of the radio housing and secure it. If you are not installing an equalizer, snap the equalizer dummy plate into the opening.

KIT COMPONENTS
Equalizer
Dummy
Plate
Rear Support
Bracket
KIT FEATURES
Shaft and
DIN unit
provisions
Equalizer
provisions
Rear support
provisions
TOOLS REQUIRED
Cutting tool
Phillips screwdriver
86-5618 or AW-FDRT -
Head unit removal keys
99-5600
AW-560FD
INSTALLATION
INSTRUCTIONS
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-09 METRA ELECTRONICS CORPORATION
REV. 08-04-09
Radio Housing
APPLICATIONS
CAR PAGE
FORD
Crown Victoria 1995-09.................... 1-2
Econoline 1997-08............................ 1-2
Explorer 1995-01...............................1-2
Ranger 1995-09................................ 1-2
LINCOLN
Continental 1995-97..........................1-2
Mark VIII 1996-98..............................1-2
Town Car 1995-02.............................1-2
MAZDA
B-Series Pickup 1995-09...................1-2
MERCURY
Grand Marquis 1995-09.....................1-2
Mountaineer 1997-01........................1-2
Marauder 2003-04..............................1-2
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• Please see www.metraonline.com for specific interface harness
Antenna Adapter:
• 40-CR10 - Chrysler antenna adapter 02-up
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.
1
2
4 5
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
Re-connect the battery terminal and test the unit
for proper operation. Mount the Rear Support
Bracket to the back of the unit. Snap the head
unit/kit assembly into the sub-dash. (Be sure the
Rear Support Bracket engages the support shelf
in the dash).
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
Disconnect the negative battery terminal to prevent an accidental short circuit. Using Metra's
86-5618 or AW-FDRT, pull the factory head unit from the dash and disconnect the wiring.
1
B-SERIES PICKUP, ECONOLINE, EXPLORER, MOUNTAINEER, RANGER: Position the
Radio Housing with the radio opening at the TOP for the remainder of the installation. (see
Fig. A)
CONTINENTAL, CROWN VICTORIA, GRAND MARQUIS, MARAUDER, MARK VIII,
TOWN CAR:
Position the Radio Housing with the radio opening at the BOTTOM for the
installation. (see Fig. B)
2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft
nuts. (see Fig. A)
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing. Slide the
DIN cage into the Housing and secure by bending the metal locking tabs down. Slide the
aftermarket head unit into the cage until secure. (see Fig. B)
(If an equalizer will be included, slide the unit into the back of the Radio Housing and secure.
If an equalizer will NOT be included, snap the Equalizer Dummy Plate into the opening).
2
3
Fig. A
Fig. B
ALL VEHICLES
Fig. A
Fig. B
remainder of the
  • Page 1 1
  • Page 2 2

Metra 99-5600 Installation guide

Metra
Brand
Metra
Model
99-5600
Category
Mounting kits
Type
Installation guide
This manual is also suitable for

Metra Electronics 99-5600 is a car stereo installation kit designed to fit a variety of Ford, Lincoln, and Mercury vehicles. It includes a radio housing, equalizer, dummy plate, and rear support bracket. The kit allows you to install a 2-shaft or DIN head unit in your vehicle.

The 99-5600 kit is easy to install. Simply remove your factory head unit and disconnect the wiring. Then, slide the aftermarket head unit into the kit and secure it with the shaft nuts or DIN cage. If you are installing an equalizer, slide it into the back of the radio housing and secure it. If you are not installing an equalizer, snap the equalizer dummy plate into the opening.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents