Frigidaire FGQ1442ES2 Installation guide

Brand: Frigidaire

Model: FGQ1442ES2

Category: Electric laundry dryers

Type: Installation guide

Installation Instructions

Gas & Electric Dryer

Instructionsd'lnstallation

Secheuse a Gaz ou Electrique

instrucciones para la instalaci6n

Secadora a Gas y Electrica

www.frigidaire.com P/N 137101400 (0806)

CONTENTS

Pre-lnstallation Requirements .......................................................................................................................................... 2

Electrical Requirements .................................................................................................................................................. 3

Gas Supply Requirements ............................................................................................................................................... 3

Exhaust System Requirements ...................................................................................................................................... 3-5

Location of Your Dryer.................................................................................................................................................... S

Rough-In Dimensions ..................................................................................................................................................... 6

Unpacking ................................................................................................................................................................... 7

General Installation ....................................................................................................................................................... 7

Replacement Parts........................................................................................................................................................ 7

Mobile Home Installation ............................................................................................................................................... 8

Reversing Door Swing ................................................................................................................................................. 8-10

Electrical Installation .................................................................................................................................................... 11

Grounding Requirements .............................................................................................................................................. 11

Gas Connection ............................................................................................................................................................ 11

Electrical Connections--3-wire ....................................................................................................................................... 12

Electrical Connections--4-wire ........................................................................................................................................ 12

Francais......................................................................................................................................................................... 13-23

Espahol...................................................................................................................................................................... 24-34

SAFETY INSTRUCTIONS

Clothes dryer installation and service must be performed by a qualified installer, service agency or the gas supplier.

install the clothes dryer according to the manufacturer's instructions and local codes.

Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the dryer is

installed correctly and safely. Leave these instructions near the Dryer after installation for future reference.

NOTE: The electrical serviceto the Dryer must conform with localcodes and ordinances and the latest edition of the National Electrical

Code, ANSI/NFPA70, or in Canada, the Canadian electrical code C22.1 part 1.

NOTE: The gasserviceto the Dryer must conform with local codes and ordinances and the latest edition of the National FuelGasCode

ANSI Z223.1, or in Canada, CAN/ACG B149.1-2000

NOTE: The Dryer isdesigned under ANSIZ 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions for HOME USE only.

This Dryer is not recommended for commercial applications such as restaurants or beauty salons, etc.

RiSK OF FIRE, For your safety the information in this manual must be followed to minimize the risk of fire or

explosion or to prevent property damage, personal injury or lossof life. SAVE THESEINSTRUCTIONS.

Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Your safety and the safety of others is very important.

We have provided many important safety messages in the Use & Care Guide, Operating Instructions, Installation Instructions and on

your appliance. Always read and obey all safety messages.

This isthe safety alert symbol. This symbol alerts you to hazards that can kill or hurt you or others. All safety messages

will be preceded by the safety alert symbol and the word "DANGER" or "WARNING". These words mean:

You will be killed or seriously injured if you don't follow instructions.

You can be killed or seriously injured ff you don't follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the

instructions are not followed.

PRE-INSTALLATION REQUIREMENTS

Tools and Materials Required for installation:

1. Phillips head screwdriver. 6.

2. Channel-lock adjustable pliers. 7.

3. Carpenter's level. 8.

4. Flat or straight blade screwdriver. 9.

5. Duct tape.

Rigid or flexible metal 4 inch (10.2 cm) duct.

Vent hood.

Pipe thread sealer (Gas).

Plastic knife.

ELECTRICAL REQUIREMENTS

i ELECTRICDryer

CIRCUIT- individual 30 amp. branch circuit fused with 30 amp.

time delay fuses or circuit breakers.

Use separately fused circuits for washers and dryers, and DO

NOToperate a washer and a dryer on the same circuit.

POWER SUPPLY- 3 wire or 4-wire, 240 volt, single phase, 60

Hz,Alternating Current.

]

POWER SUPPLYCORD KIT- 3 wire - the dryer MUSTemploy a

3-conductor power supply cord NEMA 10-30 type SRDTrated at

240 volt AC minimum, 30 amp., with 3 open end spade lug

connectors with upturned ends or closed loop connectors and

marked for use with clothes dryers. See ELECTRICAL

CONNECTIONSFORA 3-WIRE SYSTEM.

GAS SUPPLY REQUIREMENTS

Replace copper connecting pipe that is not

plastic-coated. Stainless steel or plastic-coated brass MUST

be used.

1. Installation MUSTconform with local codes,or in the absence

of local codes, with the National FuelGasCode, ANSIZ223.1

(latest edition).

4 wire - The dryer MUST employ a 4-conductor power supply 4.

cord NEMA 14-30 type SRDTor ST(asrequired) rated at 240 volt

AC minimum, 30 amp., with 4 open end spade lug connectors 5.

with upturned ends or closed loop connectors and marked for use

with clothes dryers. See ELECTRICALCONNECTIONS FOR A 4-

WIRE SYSTEM.

(Canada - 4-wire power supply cord is installed on dryer.) 6.

WARNING - Risk of Shock, Appliance grounded to neutral

conductor through a link. Grounding through the neutral link is

prohibited for (1) New branch circuit installations (2) mobile homes;

(3) recreational vehicles; and (4) areas where local codes do not

permit grounding through the neutral, (1) disconnect the link from

the neutral, (2) usegrounding terminal or leadto ground appliance

in accordance with local codes and (3) connect neutral terminal

or lead to branch circuit neutral in usual manner (if the appliance

isto be connected by means of a cord kit, use4-conductor cord

for this purpose). USECOPPERCONDUCTOR ONLY.

OUTLET RECEPTACLE- NEMA 10-30R receptacle to be located

so the power supply cord is accessible when the dryer is in the

installed position. (Canada - NEMA 14-30R receptacle.)

NEMA 10-30R NEMA 14-30R

i GAS Dryer ]

CIRCUIT- Individual 15 amp. branch circuit fused with a 15 amp.

maximum time delay fuse or circuit breaker.

POWER SUPPLY- 3 wire, 120 volt single phase,60 Hz,Alternating

Current.

POWER SUPPLYCORD - The dryer isequipped with a 120 volt 3-

wire power cord.

NOTE: Do not under any _f _t_ _

circumstances remove

grounding prong from

plug.

G PRONG

The gas supply line should be of 1/2 inch (1.27 cm) pipe.

If codes allow, flexible metal tubing may be used to connect

your dryer to the gas supply line. The tubing MUST be

constructed of stainless steel or plastic-coated brass.

The gas supply line MUSThave an individual shutoff valve.

A 1/8 inch (0.32 cm) N.RT. plugged tapping, accessible for

test gauge connection, MUST be installed immediately

upstream of the gas supply connection to the dryer.

The dryer MUSTbe disconnected from the gas supply piping

system during any pressure testing of the gas supply piping

system at test pressures in excess of 1/2 psig (3.45 kPa).

Thedryer MUSTbe isolated from the gassupply piping system

during any pressure testing of the gas supply piping system

at test pressures equal to or less than 1/2 psig (3.45 kPa).

EXHAUST SYSTEM REQUIREMENTS

Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible

metal duct and approved vent hood which has a swing-out

damper(s) that open when the dryer is in operation. When the

dryer stops, the dampers automatically dose to prevent drafts

and the entrance of insects and rodents. Toavoid restricting the

outlet, maintain a minimum of 12 inches (30.5 cm) clearance

between the vent hood and the ground or anyother obstruction.

The following are specific requirements for

proper and safe operation of your dryer. Failure to follow

these instructions can create excessive drying times and

fire hazards.

Do not install a dothes dryer with flexible

plastic venting materials. If your present system is made up

of plastic duct or metal foil duct, replace it with a rigid or semi-

rigid metal duct. InCanada and the United States if metal (foil

type) duct is installed, it must be of a specific type identified by

the appliance manufacturer assuitable for usewith clothes dry-

ers and in the United States must also comply with the Outline

for Clothes Dryer Transition Duct, ULstandard 2158A. Flexible

venting materials are known to collapse, be easily crushed and

trap lint. These conditions will obstruct clothes dryer airflow and

increase the risk of fire. Ensure the present duct is free of

any lint prior to installing dryer duct.

iI _ i i_i

ii _iII_

\,y

Correct

Incorrect

- Risk of Fire - A clothes dryer must be ex-

hausted outdoors. Do not exhaust dryer into a chimney, a

wall, a ceiling, an attic, a crawl space or any concealed space

of a building A clothes dryer produces combustible lint. If the

dryer is not exhausted outdoors some fine lint will be expelled

into the laundry area. An accumulation of lint in any area of the

home can create a health and fire hazard. The dryer must be

connected to an exhaust outdoors, Regularly inspect the

outdoor exhaust opening and remove any accumulation of lint

around the outdoor exhaust opening and in the surrounding

area.

Do not allow combustible materials (for ex-

ample: clothing, draperies/curtains, paper) to come in con-

tact with exhaust system. Thedryer MUSTNOT be exhausted

into a chimney, a wall, a ceiling, or any concealed space of a

building which can accumulate lint, resulting in a fire hazard.

Exceeding the length of duct pipe or num-

ber of elbows allowed in the "MAXIMUM LENGTH" charts

can cause an accumulation of lint in the exhaust system. Plug-

ging the system could create a fire hazard, as well as increase

drying times.

Do not screen the exhaust ends of the vent

system, nor use any screws, rivets or other fastening means

that extend into the duct and catch lint to assemble the

exhaust system, Lint can become caught in the screen, on the

screws or rivets, clogging the duct work and creating a fire haz-

ard as well as increasing drying times. Use an approved vent

hood to terminate the duct outdoors, and sealalljoints with duct

tape. All male duct pipe fittings MUSTbe installed downstream

with the flow of air.

Explosion hazard. Do not install the dryer

where gasoline or other flammables are kept or stored. If

the dryer is installed in a garage, it must be a minimum of 18

inches (45.7 cm) above the floor. Failure to do so can result in

death, explosion, fire or burns.

Number

90 °

Turns

Number

90 °

Turns

MAXIMUM LENGTH

of 4" (10.2 cm) Dia. Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

Louvered

(10.2 cm)

50 ft.(18.28 m)

52 ft.(15.84 m) 40 ft.(12.19 m)

44 ft.(13.41 m) 32 ft. (9.75 m)

32 ft.(9.75 m) 24 ft. (7.31 m)

28 ft.(8.53 m) 16 ft. (4.87 m)

MAXIMUM LENGTH

(6.35cm)

48 ft.(14.53 m)

of 4" (10.2 cm) Dia. Flexible Metal Duct

VENT HOOD TYPE

_(Preferred)

I Louvered

_10.2 cm)

30 ft. (9.14 m)

22 ft. (6.71 m)

14 ft. (4.27 m)

(6.35cm)

18ft. (5.49m)

14 ft. (4.27 m)

lO ft. (3.05m)

NOT RECOMMENDED

INSTALL MALE FITTINGS IN CORRECT DIRECTION

In installations where the exhaust system isnot described in the

charts, the following method must be used to determine if the

exhaust system is acceptable:

1. Connect an inclined or digital manometer between the dryer

and the point the exhaust connects to the dryer.

2. Setthe dryer timer and temperature to air fluff (cool down)

and start the dryer.

3. Read the measurement on the manometer.

4. The system back pressure MUSTNOTbe higher than 0.75

inches of water column. If the system back pressure is less

than 0.75 inches of water column, the system isacceptable.

If the manometer reading ishigher than 0.75 inchesof water

column, the system istoo restrictive and the installation is

unacceptable.

Although vertical orientation of the exhaust systemisacceptable,

certain extenuating circumstances could affect the performance

of the dryer:

• Only the rigid metal duct work should be used.

• Ventingverticalthrougharoofmayexposetheexhaustsystem

todowndraftscausinganincreaseinventrestriction.

Runningtheexhaustsystemthroughanuninsulatedareamay

causecondensationandfasteraccumulationoflint.

Compression or crimping of the exhaust system will cause an

increase in vent restriction.

The exhaust system should be inspected and cleaned a minimum

of every 18 months with normal usage. The more the dryer is

used, the more often you should check the exhaust system and

vent hood for proper operation.

EXHAUST DIRECTION

All dryers shipped from the factory are set up for rear exhausting.

However, on electric dryers, exhausting can be to the right or left

side of the cabinet or the bottom of the dryer. On gas dryers,

exhausting can beto the right side of the cabinet or the bottom of

the dryer. Directional exhausting can be accomplished by install-

ing ExhaustKit, P/N131456800, available through your parts dis-

tributor. Follow the instructions supplied with the kit.

EXHAUST DUCT LOCATING DIMENSIONS

3 3/4"

AS OTHER SIDE

3 3/4"

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0(0cm) 0(0cm)

Closet 0 (0 cm) 0 (0 cm) 1 (2.54 cm)

Closet door ventilation required: 2 Iouvered openings each 60

square inches (387 square centimeters)-- 3 inches (7.6 cm) from

bottom and top of door.

This dryer MUST be exhausted outdoors.

5 Thefollowing illustrations show minimum clearancedimensions

for proper operation in a recessor closet installation.

LOCATION OF YOUR DRYER

DO NOTINSTALL YOUR DRYER:

1. In an area exposed to dripping water or outside weather

conditions.

2. In an area where it will come in contact with curtains, drapes,

or anything that will obstruct the flow of combustion and

ventilation air.

3. On carpet. Floor MUST be solid with a maximum slope of 1

inch (2.54 cm).

INSTALLATION IN RECESSOR CLOSET

1. A dryer installed in a bedroom, bathroom, recess or closet,

MUSTbe exhausted outdoors.

2. No other fuel burning appliance shall be installed in the same

closet as the Gasdryer.

3. Your dryer needs the space around it for proper ventilation.

DO NOT install your dryer in a closet with a solid door.

A minimum of 120 squareinches (774.2 square cm) of opening,

equally divided at the top and bottom of the door, isrequired.

Air openings are required to be unobstructed when a door is

installed. A Iouvered door with equivalent air openings for the

full length of the door isacceptable.

ii mm

---_,_--0 (Ocm)

CLOSET DOOR

o" (Ocrn)

1" (2.54 cm)

_11 "_

0"(0 cm)

_11 _

Dryer Installation Dimensions

Free-Standing & Under Counter

48.5" To clear open door

(123.19cm)

(72.39cm)

28.5"

Gas supply pipe

on rear of unit

(5. 72cm)

2.25 _

5.0" (12.7cm)

Center line height

rear, right, left

vent

4.375" To side exhausts (11.12cm)

5.875" To base exhaust (14.93cm)

27.25 to front of cabinet (69.22cm)

27.75 to clear knobs (70.49cm)

28.5 to clear door handle (72.39cm)

_r_

'j,

0 o,_

i.......i

j.'r',_

r i- J

To rear &

base exhaust.,

27.0"

(68. 58cm)

Electrical supply

on rear of unit

36"

(91.44cm)

(94.29cm)

Stacked Dryer Installation Dimensions

(11.12cm)

4.375"

Side

exhausts

41.00"

(104.14cm)

height for rear,

right, left vents

72.00"

(182.88cm)

28.25" to front of cabinet(71.76cm)

28.75" to clear knobs (73.03cm)

29.5" to clear door handle (74.93cm)

49" to clear open door(124.46cm)

(34.29cm)

13.5" <

Gas supply pipe

on rear of unit

JI_ , 'dl"

2.375"

(6.o3cm)_

38.25"

(97.16cm)

(68. 58cm)

27.0"

001

°_,

t ..-r-.

--_--+--4-

0 i.

ILl 0

UNPACKING

1. Using the four shipping carton corner posts (two on each side),

carefully lay the dryer on its left side and remove the foam

shipping base.

Toprevent damage, do not usethe control panel

as a means to pick up or move the dryer.

2. Return the dryer to an upright position.

If your dryer does not operate, please review the "Avoid Ser-

vice Checklist" located in your Use and Care Guide before

calling for service.

Placethese instructions in a location near the dryer for future

reference.

NOTE: A wiring diagram islocated inside the dryer console or

under the top panel.

To stack your dryer on a compatible washer, visit web site

www, frigidaire.com, call your local dealer or call the Toll

Freenumber (1- 800 - 444 - 4944) to find your local distributor

to purchase stacking kit accessory part number STACKIT2.

FOAM

PAD

PACKING

GENERAL INSTALLATION

Connect the exhaust duct to outside exhaust system (seepages

3 and 4). Useduct tape to seal all joints.

With the dryer in its final position, adjust one or more of the

legs until the dryer isresting solid on all four legs. Placea level

on top of the dryer. The dryer MUST be level and resting

sofid on all four legs.

3. Plug the power cord into a grounded outlet. NOTE:Check to

ensure the power isoff at circuit breaker/fuse box before plug-

ging the power cord into the outlet.

4. Turn on the power at the circuit breaker/fuse box.

_ -" " ' Before operating the dryer, make sure the

dryer area is clear and free from combustible materials,

gasoline, and other flammable vapors. Also see that noth-

ing (such as boxes, clothing, etc.) obstructs the flow of

combustion and ventilation air.

5. Runthe dryer through a cycle check for proper operation.

NOTE: On gas dryers, before the burner will light, it isneces-

sary for the gas line to be bled of air. If the burner does not

light within 45 seconds the first time the dryer is turned on,

the safety switch will shut the burner off. If this happens, turn

the timer to "OFF" and wait 5 minutes before making another

attempt to light.

6. If your dryer does not operate, please review the "Avoid Ser-

vice Checklist" located in your Use and Care Guide before

calling for service.

REPLA CEMENT PARTS

Pedestal

A pedestal accessory, Model No. NLPWD15 (White),

NLPWD15GB (Glacier Blue), NLPWD15P (Platinum) and

NLPWD15E (Black), specifically designed for this dryer may be

used when elevating the dryer for ease of use. Failure to use

accessoriescertified by the manufacturer could result in personal

injury, property damage or damage to the dryer.

If replacements parts are needed for your dryer, contact the source

where you purchased your dryer, call 1-800-944-9044, or visit our

website, www.frigidaire.com, for the Frigidaire Company

Authorized PartsDistributor nearest you.

Label all wires prior to disconnection when

servicingcontrols. Wiring errorscan causeimproper and dangerous

operation. Verify proper operation after servicing.

Destroy the carton and plastic bags after the dryer

is unpacked. Children might use them for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight

chambers causing suffocation. Place all materials in a garbage

container or make materials inaccessible to children.

The instructions in this manual and all other

literature included with this dryer are not meant to cover every

possible condition and situation that may occur. Good safe practice

and caution MUST be applied when installing, operating and

maintaining any appliance.

MOBILE HOME INSTALLATION

Dryer MUSTbe exhausted outside (outdoors, not beneath the

mobile home) using metal ducting that will not support

combustion. Metal ducting must be 4 inches (10.16 cm)in

diameter with no obstructions. Rigid metal duct ispreferred.

If dryer isexhausted through the floor and area beneath the

mobile home isenclosed, the exhaust systemMUST terminate

outside the enclosure with the termination securely fastened

to the mobile home structure.

When installing a gas dryer into a mobile home, a provision

must be made for outside make up air. This provision isto be

not lessthan twice the area of the dryer exhaust outlet.

This dryer MUST be fastened to the floor. Mobile Home

Installation Kit No. 346764 isavailable from your dealer.

Referto pages2 and 3 for other important venting requirements.

Installation MUST conform to current Manufactured Home

Construction & Safety Standard (which isa Federal Regulation

Title 24 CFR-Part32-80) or when such standard isnot applicable,

with American National Standard for Mobile Homes.

The dryer isdesigned under ANSI Z21.5.1 or ANSI/

UL2158 - CAN/CSA C22.2 (latest editions) for HOME USEonly.

\ )'

Correct

_iill

ii _: i _

DON'T

'\. S

incorrect

REVERSING DOOR SWING

Sofid Door Reversing Instructions:

1. Open door and remove four (4) plugs in the door opening

opposite the hinges. Retain all parts for uses later, un-

less otherwise noted. Note: Use care in removing plugs

in not scratching paint on the front panel.

REMOVE 4 SCREWS

(ONE FROM EACH

HINGE FIRST)

Begin removing the four (4) screws that attach the hinge

to the front panel. Forbest results, start by only removing

one screw per hinge. Then only loosen the two remaining

screws while firmly holding door to prevent damage to

hinge, front panel or door. After the remaining screws are

loosened, continue to remove all.

3. Placedoor handle side down on a towel or pad to prevent

any possible scratches to door. Remove all remaining

four (4) screws between hinge and door.

4. Remove four (4) screws on opposite side of door.

5. Separateinner door from outer door by placing a flat screw

driver or putty knife. Rotate the inner door 180 degree

and reassemble the two door halves.

6. Install four (4) screws securing door halves where hinge

was previously attached.

7. Install four (4) screws securing hinge to door assembly.

8. Remove striker and discard.

9. Remove square plug and reinstall in hole striker was just

removed.

l O.Install striker (included in literature bag)into hole square

plug was previously installed.

11.Grasping firmly the top of the door, position the door near

the door opening and align the top hinge hole to the top

hole in the front panel door opening. Once the first screw

is started, attach the second screw to the lower hinge.

Once both screws are tightened, install the remaining

two screws.

Window Door Reversal Instructions

Figure 1

1.Open door and remove four (4) plugs in the door opening

opposite the hinges. Retain all parts for uses later, unless

otherwise noted. (Figure 1) Note: Use care in removing plugs

in not scratching paint on the front panel.

Figure 4

5. Remove two (2) door handle screws and two (2) hole plugs

from door. Again taking care not to scratch paint on door.

(Figure 4)

Figure 2

2. Begin removing the four (4) screws that attach the hinge to

the front panel. (Figure 2) For best results, start by only

removing one screw per hinge. Then only loosen the two

remaining screws while firmly holding door to prevent damage

to hinge, front panel or door. After the remaining screws are

loosened, continue to remove all.

Figure 5

6. Pull handle away from door assembley. (Figure 5)

Figure 6

7. Separate the outer door from the inner door assembly with

a putty knife or flat screw driver. (Figure 6)

Figure 3

3. Placedoor on a towel or pad handle side down to prevent

any possible scratches to door. Remove all remaining four (4)

screws between hinge and door. (Figure 3)

4. Remove four (4) screws from side of door opposite of where

hinge was mounted.

Figure 7

11. Reassemble lens to transition ring with holes to install

handle on right-hand side of door assembly. For proper fit

insure the retention tabs on transition ring are on top of lens

8. Remove lens locating screw. (Figure 7)

Figure 8

9. Disengaging several of the retention tabs and pull lens away

from the transition ring. (Figure 8)

Figure 9

Figure 10

Figure 11

12. Reassemblyouter door to inner door assembly. (Figure 11)

13. Install four (4) screws securing hinge to door assembly in

the new location, take note to place hinge in correct

orientation.

14. Install four (4) screws into holes that had secured the

hinge.

15. Remove striker and discard.

16. Remove square plug and reinstall in hole striker was just

removed.

17. Install striker (included in literature bag) into hole square

plug was previously installed.

10. Remove two (2) transition ring plugs and reinstall on

previous handle side. (Figures 9 and 10)

Figure 12

18. Reinstall door handle by placing the handle mounting

bossesthrough holes in lens and transition ring and installing

screws through inner door and tighten into handle bosses.

(Figure 12).

19. Grasping firmly the top of the door, position the door near

the door opening and align the top hinge hole to the top hole

in the front panel door opening. Once the first screw isstarted,

attach the second screw to the lower hinge. Once both screws

are tightened, install the remaining two screws.

20. Install four (4) plugs into the front panel door opening

where hinges were originally installed.

ELECTRICAL INSTALLATION

I ELECTR/CDryer I

The following are specific requirements for

proper and safe electrical installation of your dryer. Failure

to follow these instructions can create electrical shock and/

or a fire hazard.

This appliance MUST be properly grounded.

Electrical shock can result if the dryer is not properly grounded.

Follow the instructions in this manual for proper grounding.

Do not use an extension cord with this dryer.

Some extension cords are not designed to withstand the amounts

of electrical current this dryer utilizes and can melt, creating

electrical shock and/or fire hazard. Locate the dryer within reach

of the receptacle for the length power cord to be purchased,

allowing some slack in the cord. Refer to the pro-installation

requirements in this manual for the proper power cord to be

purchased.

A U.L. approved strain relief must be installed

onto power cord. If the strain relief isnot attached, the cord can

be pulled out of the dryer and can be cut by any movement of the

cord, resulting in electrical shock.

Do not use an aluminum wired receptacle with

a copper wiredpower cord andplug (or vice versa). A chemical

reaction occurs between copper and aluminum and can cause

electrical shorts. The proper wiring and receptade is a copper

wired power cord with a copper wired receptacle.

NOTE: Dryers operating on 208 volt power supply will have longer

drying times than operating on 240 volt power supply.

GROUNDING REQUIREMENTS

I USA ELECTR/CDryer 1

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check with a

licensed electrician if you are in doubt asto whether the appliance

isproperly grounded.

For a grounded, cord-connected dryer:

1. The dryer MUSTbe grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electricalshock

by a path of least resistance for electrical current.

If your dryer isequipped with a power supply cord having an

equipment-grounding conductor and a grounding plug, the

plug MUST be plugged into an appropriate, copper wired

receptacle that is properly installed and grounded in

accordance with all local codes and ordinances. If in doubt,

call a licensed electrician. Do not modify plug provided

with the appliance.

-i

Canadian ELECTR/CDryer j

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check with a

licensed electrician if you are in doubt asto whether the appliance

isproperly grounded.

Fora grounded, cord-connected dryer:

1. The dryer must be grounded. In the event of a malfunction or

breakdown, grounding will reduce the risk of electrical shock

by a path of least resistance for electrical current.

Since your dryer isequipped with a power supply cord having

an equipment-grounding conductor and a grounding plug, the

plug must be plugged into an appropriate outlet that isproperly

installed and grounded in accordance with all local codes and

ordinances. If in doubt, call a licensed electrician. Do not

modify plug provided with the appliance.

ALL GASDryers

1.The dryer isequipped with a three-prong (grounding) plug

for your protection against shock hazard and should be

plugged directly into a properly grounded three-prong

receptacle. Do not cut or remove the grounding prong

from the plug.

GAS CONNECTION

Remove the shipping cap from gas pipe at the rear of the

dryer.

NOTE: DO NOTconnect the dryer to L.R gas servicewithout

converting the gasvalve.An L.Rconversion kit must be installed

by a qualified gas technician.

2.Connect a 1/2 inch (1.27 cm)I.D, semi-rigid or approved pipe

from gas supply line to the 3/8 inch (0.96 cm) pipe located on

the back of the dryer (seepages 6 and 7). Use a 1/2 inch to 3/

8 inch (1.27 cm to 0.96 cm) reducer for a connection. Apply

an approved thread sealer that is resistant to the corrosive

action of liquefied gases on all pipe connections.

3. Open the shutoff valve in the gas supply line to allow gas to

flow through pipe.

4. Testall connections by brushing on a soapy water solution.

NEVER test for gas leaks with an open flame.

For a permanently connected dryer:

1. ThedryerMUSTbe connected to a grounded metal, permanent

wiring system;or an equipment grounding conductor must be

run with the circuit conductors and connected to the

equipment-grounding terminal or lead on the appliance.

VALVE OPEN /

GAS FLOW POSITION

[

ELECTRICALCONNECTIONS

FOR 3- WIRE SYSTEM

USA ELECTRICDryer

Remove the screws securing the terminal block access cover

and the strain relief mounting bracket located on the back of

the dryer upper corner.

install a U.L. approved strain relief into the power cord entry

hole of the mounting bracket. Finger tighten the nut only at

this time.

GREEN

GROUND

SCREW

SILVERTERMINAL

NEUTRAL

GROUND

WIRE

IUT

TIGHTEN NUT

TO THESE

THREADS

RELIEF

MOUNTING

BRACKET

POWER CORD

Thread a U.L. approved 30 amp. power cord, NEMA 10-30

type SRDT,through the strain relief.

Attach the power cord neutral (center wire) conductor to the

silver colored center terminal on the terminal block. Tighten

the screw securely.

Attach the remaining two power cord outer conductors to the

outer brass colored terminals on the terminal block. Tighten

both screws securely.

Do not make a sharp bend or crimp wiring/

conductor at connections.

Reattach the strain relief mounting bracket to the back of the

dryer with two screws. Tighten screws securely.

Tighten the screws securing the cord restraint firmly against

the power cord.

Tighten the strain relief nut securely so that the strain relief

does not turn.

9. Reinstall the terminal block cover.

[

ELECTRICALCONNECTIONS FOR4-WIRE SYSTEM

USA ELECTRICDryer

]

Remove the screws securing the terminal block accesscover

and the strain relief mounting bracket located on the back of

the dryer upper corner.

Install a U.L. approved strain relief in the entry hole of the

mounting bracket. Finger tighten the nut only at this time.

Remove the ground wire from the green ground screw

located above the terminal block.

GREEN POWER CORD

GREEN GROUND WIRE

GROUND _ SILVERTERMINAL

SCREW _ [_._,_.._ . /

_ __:_TERMINALBLOCK

NEUTRAL-- YY BACK 'o H? g2UT

A NUT

_/// RELIEF

/ MoRuENTING

/ /POWERCORD

4. Thread a U.L. approved 30 amp power cord, NEMA 14-30

type STor SRDTthrough the strain relief.

TYPICAL 4

CONDUCTOR_ TYPICAL 4 BLACK

COND UCTOR _ WHITE

30 AMP NEMA 14-30 TYPE SRDT OR ST _GREEN

5. Attach the green power cord ground wire to the cabinet with

the green ground screw.

Attach the white (neutral) power cord conductor from the

power cord and the neutral ground wire from the dryer harness

to the silver-colored center terminal on the terminal block.

Tighten the screw securely.

7. Attach the red and black power cord conductors to the outer

brass-colored terminals on the terminal block.

Do not make a sharp bend or crimp wiring/

conductor at the connections.

8. Tighten the screws securing the cord restraint firmly against

the power cord.

9. Tighten the strain relief nut securely so the strain relief does

not turn.

l O.Reinstallthe terminal block access cover.

Page is loading ...

Frigidaire FGQ1442ES2 Installation guide

Brand: Frigidaire

Model: FGQ1442ES2

Category: Electric laundry dryers

Type: Installation guide

Download PDF

report

in other languages

français: Frigidaire FGQ1442ES2 Guide d'installation
español: Frigidaire FGQ1442ES2 Guía de instalación

Frigidaire FGQ1442ES2 Installation guide

Frigidaire FGQ1442ES2 Installation guide

in other languages

Related papers

Other documents