Miller STANDARD RUNNING GEA Owner's manual
- Category
- Car kits
- Type
- Owner's manual
This manual is also suitable for
OWNER’S MANUAL
ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2020 Miller Electric Mfg. LLC
OM-269238D 2020−03
Standard Running Gear/Cylinder Rack (301239)
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
DANGER ! - Indique une situation dangereuse qui, si elle
n’est pas évitée, entraînera la mort ou des blessures
graves. Les éventuels risques sont représentés par les
symboles joints ou expliqués dans le texte.
Fsafe1 2013-10
Wear safety glasses with side shields.
Porter des lunettes de sécurité avec écrans latéraux.
Fsafe8 2013-10
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Indique une situation dangereuse qui, si elle n’est pas
évitée, entraînera la mort ou des blessures graves. Les
éventuels risques sont représentés par les symboles
joints ou expliqués dans le texte.
Fsafe2 2013-10
Tipping equipment can injure, and damage equipment. Do
not move cart where two wheels are at different heights
and cart could tip − avoid tipping. Be careful when moving
unit over uneven surfaces.
Do not use an oversized cylinder or exceed maximum
cylinder weight.
Un appareil qui bascule peut s’endommager ou causer
des blessures. Pour éviter un renversement, ne pas dé-
placer un chariot sur un terrain incliné. Demeurez prudent
lors du déplacement sur un sol inégal.
Ne pas utiliser de bonbonnes surdimensionnées et ne
pas dépasser le poids maximum d’une bonbonne.
Fsafe23 2013-10
NOTICE
AVIS
Indicates statements not related to personal injury.
Signale des consignes non associées aux dommages
corporels.
Indicates special instructions.
Fournit des instructions spéciales.
Fsafe3 2013-10
Cylinders contain gas under high pressure and can ex-
plode if damaged. Never let a welding electrode touch
any cylinder. Always secure cylinder to running gear, wall,
or other stationary support.
Les bonbonnes contiennent du gaz sous haute pression
et peuvent exploser si elles sont endommagées. Ne
jamais toucher une bonbonne avec une électrode. At-
tacher toujours une bonbonne à un mur ou à un support
fixe.
Wiresafe1 2013-10
Beware of electric shock from wiring. Disconnect input
power before installing this kit. Reinstall all panels and
covers.
Attention aux décharges électriques au contact des
câbles. Couper l’alimentation électrique avant d’installer
ce kit. Réinstaller tous les panneaux et couvercles.
Fsafe7 2013-10
Falling equipment can injure, and damage equipment.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift and sup-
port unit only with proper equipment and correct proced-
ures. Follow the guidelines in the Applications Manual for
the Revised NIOSH Lifting Equation (Publication No.
94−110) when manually lifting heavy parts or equipment.
La chute de l’équipement peut provoquer des blessures
ou des dommages matériels. Ne jamais mettre une partie
du corps sous l’appareil pendant le levage. Les fourches
de levage doivent ressortir du côté opposé de la base. Ne
soulever l’appareil qu’avec un équipement en bon état
selon les procédures correctes. Suivre les consignes du
Manuel des applications pour l’équation de levage NIOSH
révisée (publication Nº 94–110) lors du levage manuel de
pièces ou équipements lourds.
Fsafe19 2013-10
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Cancer and Reproductive Harm − www.P65W
arnings.ca.gov
PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS
AVERTISSEMENT : cancer et troubles de la reproduction − www.P65W
arnings.ca.gov
.
Fsafe26 2018-01
OM-269238 Page 2
1. 267164 Frame Rails, Mounting (2)....
2. 267165 Handle, (1).................
3. 267166 Tray, Top (1)................
4. 267167 Tray, Bottom (1).............
5. 267168 Axle, Running Gear (1)......
6. 267169 Frame, Mounting Rear (1).....
7. 267170 Wheel (2)..................
8. 267171 Bracket, Support Bottle (1)....
9. 267172 Hanger, Cable Vertical (4).....
10. 267173 Tab, Locking (1).............
11. 278722 Bracket, Consumable Tray (1).
127493 Box, Plastic 5 Compartment (1)
12. 267773 Caster, Swvl (2).............
13. 200120 Chain, Double Loop (1).......
14. 235618 Label, Warning (1)..........
267772 Hardware Kit (consisting of)
15. Screw, No. 10 x .625 Philips (17)
16. Screw, 1/4−20 x 2.5” (8).....
17. Screw, 1/4−20 x .5” (2).......
18. Washer, Flat 1/4” (10).........
19. Nut, 1/4-20 Hex (10)..........
20. Washer, Flat 1/2” (2).........
21. Nut, 1/2-13 Hex (2)..........
22. Retaining Ring (2)...........
23. Plug, Tubing (4).............
24. Spacer (2)..................
Be sure to provide Model number when
ordering replacement parts.
Ref. 269250-B / Ref. 269249-D
Description (Qty)
Part
No.
Item
No.
1
2
6
5
3
4
7
8
9
10
11
12
19
16
15
13
22
21
20
18
17
24
23
14
2. Parts Location And Assembly
OM-269238 Page 3
3. Assembly Instructions
Slide Axle (5) thru axle holes on
Frame Rails (1).
Attach Bottom Tray (4) to Frame
Rails using two #10 Phillips screws
(15).
Attach Top Tray (3) to Frame Rails
(1) using four #10 Phillips screws
(15).
Attach casters (12) using washer
(20) and nut (21). Use 3/4 in.
wrench to tighten.
Install spacers (24) over each end
of Axle (5). Slide wheels (7) onto
Axle (5) . Lightly tap Retaining
Rings (22) into slots on each end of
Axle.
Attach Bottle Support Bracket (8) to
Rear Mounting Frame (6) using
three No. 10 Phillips Screws (15).
Attach Rear Mounting Frame (6) to
Frame Rails (1) using screw (16),
washer (18), and nut (19) . Hand−
tighten all hardware. Use 7/16 in.
wrenches to tighten completely.
Attach Consumable Tray Bracket
(11) to Frame Rails (1) using
screws (16), washers (18) and nuts
(19). Hand-tighten all hardware.
Use 7/16 in. wrenches to tighten
completely.
Attach Cable Hangers (9) to Handle
(2) and Rear Mounting Frame (6)
using eight No. 10 Phillips screws
(15).
Attach Handle (2) to Frame Rails
(1) using screw (16), washer (18),
and nut (19). Hand−tighten all hard-
ware. Use 7/16 in. wrenches to
tighten completely.
Lightly tap four Tubing Plugs (23)
into the exposed ends of Rear
Mounting Frame (6) and Frame
Rails (1).
Be sure that all hardware is tight,
then place welding power source
onto cart.
Attach Locking Tab (10) to Top Tray
(3) by loosely installing two screws
(17), washers (18), and nuts (19).
Slide locking tab against front panel
of power source to secure welding
power source to cart. Tighten the
hardware using 7/16 in. wrenches.
Slide Plastic Box (not shown) into
Consumable Tray Bracket (11).
Connect Chain (13) to slots in Bottle
Support Bracket (8).
. If using a small shielding gas
bottle, install Chain (13) into
slots in Top Tray (3).
Ref. 269249-D
7/16 in., 3/4 in.
Phillips Screwdriver
Tools Needed:
1
2
6
5
3
4
7
8
9
10
11
12
19
16
15
13
22
21
20
18
17
24
23
14
-
1
-
2
-
3
Miller STANDARD RUNNING GEA Owner's manual
- Category
- Car kits
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Miller MF000000 Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
HobartWelders RUNNING GEAR/CYLINDER RACK Owner's manual
-
Grizzly T10280 Owner's manual
-
Blue Rhino GBC621CR-C User manual
-
-
-
-
NAPOLEON 495 Owner's manual
