Burley Baby Snuggler Owner's Instruction And Safety Manual

Brand: Burley

Model: Baby Snuggler

Type: Owner's Instruction And Safety Manual

Baby Snuggler

Children must be able to sit upright without

support and have adequate neck strength to

support their head before being carried in a

trailer. With younger children, this product is

recommended for strolling and jogging use only.

Consult a pediatrician to determine if a child is

of sufficient developmental age to be carried in

a bicycle trailer.

Recommended age: 6 to 24 months

the Burley Baby Snuggler can be used in any

Burley child trailer with the 5-point harness

system (2003 and later), but works best

on those models with seat pad attachment

strips on the child seat. For more information,

consult your Authorized Burley Dealer or visit

www.burley.com.

Installation

SOLO TRAILER, ONE INFANT:

1. Remove existing shoulder harness pad and

seat pad. Insert shoulder straps through

openings in Baby Snuggler back. Use the

lower strap openings for a shorter infant,

and the upper openings for a longer

infant. FIGURE A

2. Insert crotch strap through opening in Baby

Snuggler bottom. FIGURE A

3. Slide padded tubes onto shoulder straps,

with straps oriented so that FLAT parts of

male buckles face each other. FIGURE A

4. Position infant in Baby Snuggler, with infant’s

upper back centered on the Snuggler’s

lumbar support.

5. Snap male buckles into Y-buckle, with

Y-buckle positioned at infant’s sternum.

Adjust straps so infant cannot move too far

forward in Snuggler. FIGURE A

6. To secure head and shoulders, adjust

side tension cords and toggles. The upper

Snuggler will narrow, cradling the infant’s

head. To change angle of infant’s legs, adjust

side straps. FIGURE C

Baby Snuggler

Installation Instructions

FIGURE A: Baby Snuggler Installation

FIGURE B: Baby Snuggler Installation in d’lite Trailer

FIGURE C: Baby Snuggler in Reclining Position

Seat

Belt

1. For Longer

Infant

1. For Shorter

Infant

3. Strap

Tubes

2. Crotch

Strap

Adjustable

Side Tension

Cord

Adjustable

Seat Crotch

Strap

Adjustable

Side Strap

Trailer

Front

Seat Belt

Snugly

Fastened

DOUBLE PASSENGER TRAILERS, ONE INFANT:

Install Baby Snuggler in center of trailer, using the two center shoulder straps and center crotch

strap. FIGURE B Follow steps 1-7.

DOUBLE PASSENGER TRAILERS, ONE INFANT, ONE CHILD:

Install Baby Snuggler on one side of trailer, using shoulder straps and crotch strap on that side.

Follow steps 1-7, positioning infant and making Baby Snuggler adjustments before placing child

in trailer seat.

DOUBLE PASSENGER TRAILERS, TWO INFANTS:

Install Baby Snugglers using both shoulder harnesses and two outer crotch straps.

Follow steps 1-7.

FOR TRAILERS WITH RECLINING SEAT FEATURE:

For added comfort, make the following adjustments to your trailer:

1. Loosen tension on the upper and lower straps behind the trailer seat.

2. Place Baby Snuggler in trailer, with Baby Snuggler bottom toward the front of the trailer

seat. Lengthen crotch strap. FIGURE C

3. Follow steps 1-7.

Consult your Burley trailer manual for more information about the reclining seat feature.

If you do not have a copy of your trailer instruction manual, do not use the Burley Baby Snuggler.

To replace your manual, go to http://burley.com/support/manuals_current.cfm.

ALWAYS SECURE CHILDREN WITH HARNESS AND LAP BELT BEFORE USE. SECURE ACCORDING TO INSTRUCTIONS ON TRAILER SEAT

LABEL AND IN OWNER’S MANUAL. CONSULT A PEDIATRICAN BEFORE USING THIS PRODUCT. NEVER LEAVE A CHILD UNOBSERVED OR

UNATTENDED. FAILURE TO DO SO COULD RESULT IN AN ACCIDENT AND SERIOUS INJURY OR DEATH.

WARNING

SINGLE PASSENGER MUST BE SEATED IN CENTER POSITION.

IMPORTANT:

STRAPS BEHIND CHILD SEAT MUST ALWAYS BE SECURED WHEN TRAILER IS IN USE.

IMPORTANT:

Burley Baby Snuggler Owner's Instruction And Safety Manual

Burley Baby Snuggler Owner's Instruction And Safety Manual

Burley Baby Snuggler Owner's Instruction And Safety Manual

Related papers

Other documents