SMARTECH 103450 User manual

Brand: SMARTECH

Model: 103450

Type: User manual

This manual is also suitable for

Instruction Manual

TECHNICAL DATA

Length...................................420mm

Width.....................................245mm

Height....................................180mm

Wheel Base...........................268mm

Tread (F/R).....................240/245mm

Wheel Diameter...............108*53mm

.................88*41mm

Gear Rate..............................H8.25:1

...............................L5.78:1

Weight.....................................1900g

Engine.......................15CXP/ 18CXP

Our company reserves the right to change or modify this manual without notice.

FEATURES:

DISC BRAKE SYSTEM

15CX /18CXP ENGINE WITH PULL STARTER

EQUIPPED WITH EXHAUST PIPE AND AIR

FILTER

2 SPEED TRANSMISSION AND 4WD SYSTEM

OIL FILLED SHOCK ABSORBER

FRONT/REAR DIFF. BEVEL GEAR

80CC FUEL TANK WITH PRIMER BUTTON

ITEM NO.:103430

ITEM NO.:103450

1:10 SCALE 4WD OFF-ROAD BUGGY

15%-30%

Fuel

Notice before assembly

The following tools are needed for assembly. You must buy them from the local hobby

shops apart from the kits we provided.

Please read and comprehend this instruction manual before assembly.

Tools needed for assembly

Hexagonal wrenches

Scissor

Hobby knife

Cross sleeve

Super

glue

Slide cutter

Needle

nose pliers

Philips head

screw driver

(No.2)

Philips head

screw driver (No.1)

Charger

Igniter

Additional items needed to buy for

running in the engine

Diff. oil

Fuel

bumper

Air filter oil

Shock

absorber oil

Battery

Switch

Receiver

Steering servo

Throttle servo

2-Channel Transmitter system

Please read the transmitter system instructions carefully before use.

The servo must be set at the center position before installation. To set the servo to neutral

position, turn on the transmitter and receiver, and set the servo rod at the center position,

then turn off the receiver and the transmitter in succession. The servo will be at the

proper position.

Transmitter

Type:301332

Stop

Half forward

Full forward

Battery cover

Speed control trigger

"AA" battery

or Ni-cd(*8)

Left Right

Power switch

Antenna

Steering trimmer

Throttle trimmer

Steering trigger(R)

Steering trigger(L)

Throttle trigger(F)

Throttle trigger(B)

LED of power

Steering control wheel

2mm

2.5mm

1.5mm

REV/TH

REV/ST

TROUBLE SHOOTING

Problems Reasons

Solutions

Engine does

not start

Engine

flameout just

after starting

Bad reaction

and response

from engine

Car is hard

to contorl

1. No fuel in tank or in carburetor.

2. The spark plug is damaged, or the port fire

has not been charged.

3. The fuel pipe, air filter or muffler is choked.

4. Too much fuel.

5. The carburetor has not been adjusted properly.

6. The servo link has not been adjusted properly.

1. No fuel in the fuel tank.

2. The fuel pipe, air filter or muffler is choked.

3. The carburetor has not adjusted properly.

4. The engine is overheated.

1. The carburetor has not been adjusted properly.

2. Little oil pressure in muffler.

1. The batteries of the transmitter or receiver

are weak or exhausted.

2. Poor effective of the antenna.

3. The servo link has not been adjusted properly.

1. Fill the tank with fuel and press prime button.

2. replace a new spark plug or charge the portfire.

3. Clean the clogged parts or change with new one.

4. Remove the spark plug and dispose the fuel.

replace a new one if need.

5. Set the idle, main and slow needle to standard

starting position.

6. Set the servo to neutral position and readjust it.

1. Fill the tank with fuel.

2. Clean or change the clogged parts.

3. Readjust the idle, main and slow needle, set

them to starting position.

4. Cool down the engine. Unscrew the main

needle adjusting screw, turn left for 30 degree.

1. Readjust the idle, main and slow needle.

2. Assemble the pipe between the muffler and fuel

tank properly.

1. Charge the battery or replace it.

2. Extend the antenna of the transmitter and receiver.

3. Set the servo to the neutral position and readjust it.

SAFETY PRECAUTIONS

OPERATION PRECAUTION

Operate the car after completely assembled.

Avoid changing the running direction frequently

or abruptly.

Don’t run your car at following places:

-Overgrown with grass.

-Muddy, sandy or rocky.

Checks all screws and screw caps are tighten.

WARNING: To avoid accidents and personal injuries,

please observe the following items:

Handle with fuel safety:

- Only use the fuel outdoors!

- The mixture of petrol and lubricating oil should be

25:1. Suitable is super or super plus petrol.

- Never use fuel indoors, nearby fire brand or heat

producer.

- Never swallow fuel or been splashed into eyes

- Store fuel where is cool, dry and shadow, also out

of children’s reach! Tighten the cap!

- Never throw empty fuel cans into fire! Otherwise,

it may cause explosion.

Never put fingers into rotating moving parts!

Never touch engine and muffler after use, be

careful of burn yourself!

WARNING: Never use the vehicle in following situation!

-On roads or railways.

-The place where children or people gather.

-In residential, parks.

-Indoors or in incapable places.

Operating in disorder may cause personal injury and

improperly losing.

Keep alert that if someone is operating a car nearby.

Never use the same frequency with others simultane-

ously. Otherwise, the signals will be disturbed, then

the car out of control which may cause accidents.

Make sure the batteries of transmitter and receiver is

fully charge. lf not, the transmitter and receiver won’t

work efficiency, in that case, it may cause the car out

of control, even cause serious accident.

Stop the car at once if there is any abnormal with your

car. check it. Solved all problems before operating the

cars. Otherwise, further troubles may cause accidents.

1. Adjust carburetor

Please read the instructions carefully before staring engine.

Before staring

Carburetor is been adjusted in standard and not required

readsjust

Readjust according to user’s requirement

Main needle calibrating screw

1-1.5mm

Opening (rich)

Closing (lean)

Decreasing RPM

unscrewing

Increasing RPM

screwing

Idling adjusting screw

Micro adjusting screw

2. Adjusting idling

Adjusting idling

- 1-1.5mm is the standard setting of factory, adjust the

increased RPM a little bit for easy starting.

- Adjust to fuel and piston. For high neutral, turn

left/unscrew calibrating neutral screw. For slow

neutral, turn right/screw-in the screw.

Decreasing RPM

unscrewing

Increasing RPM

screwing

Calibrating neutral screw

Closing (lean)

Opening (rich)

Main needle Calibrating screw

- Maximum RPM is adjusted with main needle

- At the first drive, run as set. Turning clockwise will

be increasing RPM and turning counter-clockwise

will decreasing RPM. Turning clockwise extremely

will over-heat finally to breakage of inside of engine.

3. Main needle

Adjust the main adjusting screw

Low/middle RPM is adjusted with trimming needle.

For the first drive, try to run as set. Stop driving, and the

neutral tends to stop… finally to stoppage, adjust trimming

needle to continue. Pay attention to balancing for adjusting

both main and trimming needles

Note: When needles are changed, be sure to remember the

original positions, and turn needles by 30 degrees each time.

4. Adjust micro adjusting screw

1. The process of run-in before driving

When you get a new engine, we might remind you that

no matter what kind of engine, it is important to clean

inside of the engine. The engine will be damage if the

dust and scruff get into it.

Secondly, for the run-in process, we adopt traditional

methods. In other words, we carry out the cool run-in

process under the condition of rich gas. However, the

adjustment situation of the needle valve accords with

the situation of leaving factory. Turn down the needle

value until the carburetor is in full speed without stop,

and go on with 5 tanks oil during those process, you

should let the engine stop for a while before carry on

following process.

When going load milling, the curtate range of the needle

valve should not be adjusted excessively, approximately

1/4 round is best under preview work or reaching the

properly middle/low speed. However, the main needle

only need be curtailed a little. We suggest that the

temperature is no more than 90 centidegree .

STARTING ENGINE

2. Switch on transmitter and receiver

Extend out the antennas of transmitter and receiver.

Then, switch on transmitter and receiver.

Be sure to confirm carburetor on neural position

when receiver is put on.

15-30% Fuel Fuel pump Air filter oil

Glow plug starter

Adjust micro adjusting screw

Closing (lean)

Opening (rich)

Micro adjusting screw

Transmitter

Type:301332

Left Right

Power switch

3. Adding fuel

Use the special fuel for the model. After filling,

please fasten the cover of the fuel tank.

4. Chock button

Send the fuel into the inlet of carburetor by pushing

chock button. Push the button twice more until fuel

reaches the gate.

The inlet of the carburetor

5. Starting engine

Heat up the glow plug by the starter, and then pull

the recoil starter handle to starter the engine.

Adjust the throttle trim 2 or 3 degree for easy start.

Increasing RPM until idling stabilize after starting,

then, return to normal.

NOTE: Put the car on the ground and allowed all

wheel ratate freely, and never adjust the accelero-

grap to the maxim position.

6. Over choked

Engine cylinder is flooded with fuel, plug is wet and recoil

starter is heavy, remove plug/pull recoil starter for 20-30

times to discharge the fuel.

7. Stopping engine

Placing neutral position, remove air cleaner and turn off

air intake opening . or block exhaust opening.

NOTE: use gloves to protect hands, as exhaust pipe is

very hot.

8. Maintenance

Keeping the engine clean.

Bearing φ10*φ5*4

E-clip φ2.5

Philips head screw

TPF3*30

×4

×2

103080

103082

103080

(E2.5)

Grease

103080

103079

103104

(TT3*15)

103105

(TT3*15)

103105

103104

(TPF3*30)

103105

(TPF3*30)

103081

103083

(M4*3)

103083

(M4*3)

103081

103041

103081

103100

(TPF2*8)

103079

103042

103080

103042

103100

Bearingφ15*φ10*4

Washers

φ14*φ10.2*0.25

Diff. gear axle

Philips head screw

TT3*15

Inner hex headless

screw ISOH4*3

E-clipφ2.5

Philips head

screw TPF2*8

Diff. bevel gear

axle

×2

×3

×1

×4

×2

×1

①

③

②

④

Tighten the Diff. screw as shown.

(Builds two differentials for front and rear)

Fill the Diff. case to approx 80% with

the Diff. oil.

Front Gear Case

×2

Front and Rear Diff.

Front and Rear Gear Case

Rear Gear Case

103081

(E2.5)

Rear Gear Case

Centre Decrease Mount

Centre Decrease Mount Assembly

103024（60MM）

103025（68MM）

103031

103075

103101

103053

103086

103086(M3*3)

103036

103086

103052

103054

103085

103102

103103

103083

(M4*3)

103084(M4*4)

103088

(TPF3*32)

103088(TPF3*32)

103073

(M3*3)

103054

(TPF2*8)

103101（TPF3*10）

TPF3*10 ×6

103104

(TPF3*10)

103105

(TPF3*10)

103032

103032(M3)

103032

(M3)

103032(M3*5)

TPF3*10 ×4

ISOH4*3 ×1

ISOH4*4 ×1

TPF2*8 ×3

Washer Φ9*Φ5.08*0.2 ×3

TPF3*32 ×2

TM3*16(1/2) ×2

Pin Φ2*9.6 ×1

ISOH4*3 ×1

E-clip φ4 ×2

M3*5

Lock Nut

24MM

Front Susp. Arm Mount (L&R)

Rear Susp. Arm Mount (L&R)

Front&Rear Susp. Arm Mount (L&R)

103028

M3*12

103068

(M3*12)

14MM

103068

(M3*12)

103068

(M3*12)

103037

103011

103010

103070

(TPF3*10)

103010

(TPF3*10)

103070

103069

(TT3*12)

103023

(73mm)

103023

(73mm)

103023

(73mm)

103023

(73mm)

103068

240076

103041

103029

103035

103071

103039

103041

103067

103038

103039

103038

(E2.5)

E-clip φ2.5 ×6

Pin Φ2*9 ×2

TT3*12 ×6

ISOO3*12 ×4

Bearing φ10*φ5*4 ×4

E-clip φ2.5 ×6

Pin Φ2*9 ×2

TT3*12 ×4

ISOO3*12 ×4

Bearing φ10*φ5*4 ×4

TPF3*10

×12

F&R Shock Absorber Unit

Front Shock Absorber Assembly

Rear Shock Absorber Assembly

②

Rear Shock Absorber 2PCSFront Shock Absorber 2PCS

0-1MM

Bubble

18MM

To remove

air bubbles,

move the

positon

upper and

down slowly.

E-clip φ2.5 ×8

O Ring P3 ×8

Ball End Head

5.8 ×4

103033

(E2.5)

103034

(E2.5)

103033

103033 (P3)

103034

(P3)

103033

103021（M3）

103021（TM3*18）

103021

103015

103017

103014

103016

(M3*16)

103016

(M3*16)

103016

103122

103034

(TT3*15)

103020

(TT3*10)

103034

103020

103034

103014

103013

103109

（TT3*10）

103109

103033

103034

103021

(TT3*10)

103034 (TT3*15)

103034

(TT3*15)

103013

(TT3*12)

103034

103033

TT3*10 X1

TT3*10 X2

TT3*10 X4

TT3*12 X2

TM3*18 X2

M3 X2

TT3*15

TM3*15 X2

ISO3*16 X4

M3 X4

M3 X2

103015

(M3*16)

103020

103015(M3)

103020(M3*18)

103020

(M3)

Servo Saver System Assembly

Fuel Tank Assembly

103030

103072

(TM3*10)

103089

103106

80CC

103106

(TPF3*10)

103106

(TT3*6)

103106

(P4)

103106

(P3)

103030

103022

(TM3*16)

103022

(TM3*16)

103022

(M3)

103022

(M3)

103030

(E5.0)

103030

(ISO3*12)

103089 (TM3*12)

103030

TM3*16 (1/2)

E-clip φ5 x1

M3 x2

TT3*10 x1

TPF3*10 ×2

O Ring P3 x1

O Ring P4 x1

TT3*6 x1

10MM

Upper Floor

Upper Floor Assembly

10MM

TT3*10 X8

ISO2*10 ×2

ISO3*12 ×2

TPF3*6 ×2

TPF3*10 ×2

TT3*15

103019

103110

103055

(TT3*10)

103110

301030

103110

(TPF3*10)

103026

301010

(M2*10)

301010

103027

(TPF3*10)

103027

(TPF3*10)

103027

(TPF3*10)

103027

103019

(TPF3*6)

103019

(TPF3*10)

103040

(TT3*15)

103040

103090

103026

(TPF3*10)

103110

(TT3*10)

TPF3*10 ×8

103090

(ISO3*12)

Engine Part

Engine Assembly

②

103064

103065

103063

103062

(M3)

103062

103063

103107

103062

(ISO3*8)

103062

(ISO3*8)

103047

(M3*10)

403063

(ISO3*10)

103066

103051

103045

103046

103049

103046

103046(E7.0)

103075

103048

103047

ISOO3*30 X2

Spring Washer

M3 NYLON NUT x2

M3 NYLON NUT X5

ISOO3*8

Clip φ3.2*φ8*0.5Clip φ5.1*φ10*1.0

ISOH4*4 X1

TT3*15 X2

TM3*10 X4

ISO3*8 X4

ISO3*10 X1

E-clip φ7

103063(M3)

103057（M4）

103057

103056

(M4)

M4 NYLON NUT x4

Front and Rear Tires Assembly

Throttle Rod & Brake Rod

103043

(PB2*10)

103043

103044

ISO2*10 X1

ISOH3*3 ×3 Washer 3.2*8*0.5

103114

(E2.3)

103114(p3)

103114

Front Shock Absorber 2PCS

103113

(E2.3)

103113(p3)

103113

Car Body

②

F&R Shock Absorber Unit

Rear Shock Absorber 2PCS

0-1MM

Bubble

18MM

To remove

air bubbles,

move the

positon

upper and

down slowly.

E-clip φ2.5

O RingP3

Ball End Head 5.8

×8

Universal Drive Shaft Bearing

②

Front Tire Rear Tire

18CXP Engine Aluminum Exhaust Pipe

401770

103075

(φ10*φ5*4)

103120

(M4*4)

115010

115012

182120

103076

(φ10*φ15*4)

Apply Super glue between wheel rim and tire,

when dry, Repeat the procedure on the other

side of the wheel until fully glued.

please make sure the rim and tire fully glued

to avoide chipped off.

Apply Super glue between wheel rim and tire,

when dry, Repeat the procedure on the other

side of the wheel until fully glued.

please make sure the rim and tire fully glued

to avoide chipped off.

103430/103450 Part List (1)

103011-Rear Constuction

Wall

103012-Rear Bumper

103013-Front Bumper

103015-Rear Brace Mount

(L&R)

103122-Wing Mount 103016-Washer

103017-Tie Rod 103018-Chassis 103019-Upper Floor 103020-Rear Shock Tower

103021-Front Shock Tower 103022-Steering Plate 103023-Transmission Shaft

73.1MM

103024-Dogbone 61MM

103026-Battery Case Cover 103027-Battery Case

103028-Front Tie Rod

103029-Rear Tie Rod

103031-Brake Disc

103032-Side Guard

103010-Rear Lower Susp.

Arm

103014-Choke Plate Mount

(L&R)

103025-

Dogbone 68MM

103030-Steering Bellcrank

TT3*12 X2

ISO3*16 X4

Car Body Pin X2

TPF3*6 X2

TT3*10 X2

TM3*18 X2

Nut X2

Lock Nut X2

TPF3*10 X2

TPF3*10 X1

ISO3*12 X4

TM3*5 X6

Lock Nut X6

TT3*12 X4

M3 NUT X4

TPF3*10 X6

PT3.5*20 X2

TT3*12 X2

TM3*16

TT3*12 X4

TT3*10 X2

TM3*18 X2

Nut X2

Lock Nut X2

103430/103450 Part List (2)

103033-Front Shock Absorber 103034-Rear Shock Absorber 103035-Susp. Arm Axle

103037-Lower Susp. Shaft

(L&R)

103038-Front Linker Axle 103039-Wheel Shaft

103043-Throttle Pulling Rod 103044-Brake Rod

103036-Brake lever

103041-Rolling Bearing 103042-Rolling Bearing

103048-Clutch Gear 23T/18T

103049-Clutch Shoe

103052-Bearing 103053-Joint Hub 103054-3# Gear Hub

Pin Φ4 X1

103050-Clutch Gear Unit

103051-Engine Flywheel

103047-Engine Mount103045-Filter Foam

x1 set

103046-Engine Gear Shaft

103040-Front Joint Plate

101099-Car Body

(For 103450)

350130-Car Body

(For 103430)

TT3*15 X2

E-Clip Φ2.3 X2

TT3*15 X2

TT3*15

E-ClipΦ2.3 X4

E-ClipΦ2.3 X2

E-Clip Φ7 X1

ISOH3*3 X2

ISOO3*8 X1

Washer of Spring φ3.2*φ8*0.5

WasherΦ3.2*Φ8*0.5 X1

WasherΦ5.1*Φ10*1.0 X2

PB2*10 X1

ISOH3*3 X1

Washer X4

TM3*10

TPF3*6 X2

TPF3*8 X3

103430/103450 Part List (3)

103055-Anttena

x4 pcs

103056-Rear Wheel Unit 103057-Front Wheel Unit

ISO3*8 X4

TPF3*10 X6

Washer X2

ISOO3*30 X2

ST2.9*12 X4

TT3*12 X2

M3 NYLON NUT X4

M3 NYLON NUT X1

M3 NYLON NUT X2

ISO3*10 X1

103058-Front Rim

103059-Rear Rim 103060-Rear Tire 103061-Front Tire 103062-Engine Holder

103063-Iron Brace 103065- Silicon Connecting

Pipe

103066-Exhaust Pipe

103067-Front Steering Arm 103068-Front Linker (L&R)

103069-Front Lower Susp.

Arm

103070-Front Construction

Wall (L&R)

103071-Rear Bearing Mount

103073-Clutch Unit

103074-Diff Gear Unit103072-Tube

103075-Bearing 103076-Bearing

103078-Diff. Gear Box Unit

103064-Exhaust Pipe

Connector

TM3*10

103077-Brake Cam Set

ISOH3*3 X1

TT3*10

Page is loading ...

SMARTECH 103450 User manual

Brand: SMARTECH

Model: 103450

Type: User manual

This manual is also suitable for

Download PDF

report

SMARTECH 103450 User manual

This manual is also suitable for

SMARTECH 103450 User manual

Other documents