Whirlpool AWO 9166 Program Chart

Category
Washing machines
Type
Program Chart
5019 301 05600/A
GB AWO 9166 PROGRAMME CHART
1)
For improved garment care spin speed is restricted to 1000 rpm in this programme.
2)
For improved garment care spin speed is restricted to 400 rpm in this programme.
Whirlpool is a registered trademark of Whirlpool USA
A. Programme selector knob and
“Start/Pause” button
LCD-Display
B.
“Menu” button ( )
C.
“Back” button
D.
“Info” button
E.
“Up” and “Down” buttons to set
temperature and spin speed
F.
“OK” button for confirmation
G.
“Reset” button
H.
“Start Delay” button
Programme
Care
Labels
Type of wash/
Degree of soiling
Max.
load
Detergent and Additives
Selectable special options =
Tempe-
rature
Max.
Spin
Speed
Notes
Softener Main
wash
Pre-
wash
Start
Delay
Pre-
wash
Intensive
Rinse
Rinse
Hold
Speed
Reduction
Easy
Iron
Extra
care
Kg
Avvio
ritardato
°C rpm
Cotton
Cotone
Normal to heavily soiled bed linen, table
linen and underwear, towels, shirts etc.
made of cotton or linen.
6.0
Yes
❉❉
20 to 95 1600
“Prewash” can be additionally
selected for heavily soiled laundry at
any temperature.
Synthetic
Sintetici
Normal soiled blouses, shirts and other
outer clothing made of polyester (Diolen,
Trevira), polyamide (Perlon, Nylon) or
mixtures of these fibres with cotton.
2.5
Yes
❉❉
1)
❉❉
20 to 60 1000
1)
“Prewash” can be additionally
selected for heavily soiled laundry.
Daily Load
Normal to lightly soiled textiles made of
cotton and/or easy care fibres.
3.0
Yes
❉❉
30 to 60 1600
Rapid Plus
Rapido
Lightly soiled outer and sport clothing
made of cotton, polyester, polyamid and
mixed cotton fabrics.
3.0
Yes
––
❉❉
––
20 to 60 1600
Delicates
Delicati
Curtains and delicate dresses, skirts,
shirts and blouses.
1.5
Yes
❉❉
1)
––
20 to 40 1000
1)
Wool
Lana
Only woollens with a felt-free finish,
labelled with the woolmark and stated as
machine washable.
1.0
Yes
––
1)
––
20 to 40 1000
1)
If you select “Rinse Hold” do not
leave items to soak for too long.
Handwash
Lavaggio a
mano
Textiles made of linen, silk, wool or
viscose marked as “handwashable”.
1.0
Yes
––
2)
––
20 to 30 400
2)
If you select “Rinse Hold” do not leave
items to soak for too long. A very
gentle spin is used in this programme.
Rinse & Spin
Risciacquo &
Centrifuga
––
6.0
––
❉❉
––
20 1600
Same as the spin cycle in the
“Coloured Cotton” programme.
Spin
Centrifuga
––
6.0
––
––
––
1600
In this programme spinning is
intensive. Same as the spin cycle in
the “Coloured Cotton” programme.
Gentle Spin
Centrifuga
breve
––
1.5
––
––
1)
––
1000
1)
A very gentle spin is used in this
programme. Same as the spin cycle in
the “Wool” programme.
Drain
Scarico acqua
––
––
This programme only drains (alternative
method of terminating the programme
after “Rinse Hold” without spinning). In
addition all running programmes can be
cancelled with this programme.
6
th
Sense
intelligent technology always guarantees perfect results with maximum efficiency whatever
the wash load.
6
th
Sense
intelligent technology always guarantees perfect results with maximum efficiency whatever
the wash load.
B
E
F
C
G
A
H
D
3gb05600a.fm Page 1 Friday, October 1, 2004 5:39 PM
Black process 45.0° 100.0 LPI
5019 301 05600/A
Whirlpool is a registered trademark of Whirlpool USA
Add the detergent as described in the chapter “Detergent
and Additives” in the booklet.
1. Turn the
programme selector knob
in any direction
to the desired programme.
This appears in the LCD display, together with spin
speed, wash temperature and wash programme
duration (in hours and minutes). The indicator light
above the
“Start/Pause”
button will blink.
2. Temperature and spin speed can be changed using the
“menu”
button as well as the “ ” and “ ” buttons.
The additional options available for the wash
programme can be selected with the
“menu”
button.
Pour an appropriate amount of chlorine bleach into the
main wash.
Use ONLY “Rapid Plus” programme at MAXIMUM
temperature of 20°C.
“Spin Speed”
A maximum spin speed is assigned to each
programme.
Press the
“menu”
button until “To set Spin Speed”
appears in the LCD display. The set spin speed blinks
and can be changed with the “” and “” buttons.
If the spin speed “0” is selected, the final spin is
cancelled. The water is drained out only.
“Prewash”
Only for heavily soiled laundry (for example. sand or
granular dirt). Programme duration is increased by
some 15 min.
“Intensive rinse”
An additional rinse cycle is carried out.
This additional option is particularly suitable for areas
with very soft water, for washing baby linen and
helping people with detergent allergies.
“Rinse hold”
The laundry remains in the last rinse water without
being spun: discoloration of the laundry and additional
creasing are prevented.
This option is particularly recommended for the
programme “Easy Care” or “Delicates”.
This additional function is particularly useful if you want
to postpone spinning to a later time.
Note:
The programme has reached “Rinse hold” when
the corresponding symbol blinks in the LCD.
Terminate the “Rinse Hold” option:
•Press the
“Start/Pause”
button; the programme will
terminate automatically with the appropriate spin cycle
for the current programme.
If you do not wish to spin the clothes, turn the
programme selector knob to “Drain” and press the
“Start/Pause”
button.
CONSUMPTION DATA
*
Programme Temperature
(°C)
Size of wash
(kg)
Water
(l)
Energy
(kWh)
Programme duration **
approx.
(hours : minutes)
Cotton
95 6.0 49*** 1.90 2:00
Cotton
60 6.0 44 1.14 2:20
Cotton with “Extra care” ****
60 6.0 44 1.02 2:30
Cotton
40 5.0 42 0.70 2:00
Easy Care
60 2.5 55*** 0.70 1:30
Easy Care
40 2.5 50 0.50 1:15
Daily Load
40 3.0 43 0.55 1:00
Rapid Plus
30 3.0 37 0.40 0:30
Delicates
30 1.5 60 0.50 0:45
Wool
40 1.0 60 0.50 0:40
Handwash
30 1.0 45 0.40 0:35
*Consumption
values
were measured in normal conditions in compliance with Standard IEC/EN 60456.
** The
programme duration
may vary from the chart values. The washing machine will allow for individual household
conditions and adapt the programme run time accordingly.
*** To reduce
the water temperature, some cold water is
added at the end of the main wash cycle, before the pump
drains the water out.
**** Reference Programme for Energy Label
POUR IN DETERGENT, CLOSE THE DOOR
AND SELECT A PROGRAMME
USING CHLORINE BLEACH
PRESS THE DESIRED SPECIAL OPTION
BUTTON
“Extra care”
With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Easy Iron”
To lessen creasing, the water quantity is increased and
the clothes are spun very gently at reduced power.
This makes your laundry significantly damper at the
end of the programme.
Turn the programme selector to “Memory”.
Select one of the 10 storage spaces using the “ ” or
” button and confirm with
“OK”
.
A list of all the available wash programmes appears in
the LCD. Select the desired programme with “
and “ ” and confirm with
“OK”
.
You can then, as already described, select additional
options for the wash programme and set temperature
and spin speed as desired.
When all the settings have been made and confirmed
with
“OK”
, the programme is stored in the selected
storage space and can be reselected at any time and
run using
“Start/Pause”
.
The “Start Delay” allows you to run the machine at your
convenience, for example at night when electricity is
cheaper.
Press the “Start Delay” button. Using the “ ” and
” keys, you can set the time on the display to
when you want the wash programme to start, then
confirm this with
“OK”
.
Press the
“Start/Pause”
button. “Start at ...” appears
in the LCD display until the preset start time is reached.
The wash programme then starts automatically.
During the programme, the remaining time appears in
the LCD.
“Start Delay” correction
If you have already confirmed the desired start time
with
“OK”
or have already pressed
“Start/Pause”
,
they can still be changed. To do this, press the “Start
Delay” button again.
The set time blinks and can be changed with the “
and buttons. Then you only need to confirm the
changed time with
“OK”
again.
After you have selected the programme and any additional
options, the indicator light above the
“Start/Pause”
button blinks. Turn on the tap and start the programme by
pressing the
“Start/Pause”
button.
The indicator light above the button will now illuminate.
The stage of the wash programme appears in the LCD, as
well as the time remaining until the end of the wash
programme.
Within the first 15 minutes after the start of the “Cotton”
and “Easy Care” programmes the door can be opened to
add further laundry.
“You can add an item” will appear in the LCD as long as this
option exists. This is not possible if “Rapid Plus” is selected.
The time remaining on the LCD shows 0:00, and
displays “END OF CYCLE”.
1. Turn the programme selector with the marking to the
top.
2. Close the water tap.
3. Open the door and unload the machine.
A newly-selected programme will continue in the same
programme section during which the current programme
was interrupted. Therefore do not add any more detergent.
1. Press the
“Start/Pause”
button to interrupt the
programme.
The indicator light flashes.
2. Select the new programme (with temperature), any
additional options and - if you wish - another spin
speed. In this way you can also select an additional
option later, without changing the current programme.
3. Press the
“Start/Pause”
button again to re-start the
programme.
If you are in the “Prewash” programme step this
additional option can not be deselected as described
(to do this see “Cancel/Delete programme”)
1. Press the
“Start/Pause”
button to interrupt the
programme.
The indicator light flashes.
2. Press the “Reset” button.
“Do you want reset” appears in the LCD.
3. Confirm with the
“OK”
button to start draining the
water.
STORE INDIVIDUAL PROGRAMME
(“Memory”)
START DELAY
PROGRAMME START
DOOR LOCK
PROGRAMME END
RESELECT AFTER PROGRAMME START
CANCEL/DELETE PROGRAMME
3gb05600a.fm Page 2 Friday, October 1, 2004 5:39 PM
Black process 45.0° 100.0 LPI
GB
Brief instructions for washing machines with LCD display
Your washing machine is ready to use
5019 301 05600/A
Whirlpool is a registered trademark of Whirlpool USA
First use
Please always follow the installation instructions enclosed with the
appliance.
Turn the programme selector knob with the marking to
highlight
“Settings”.
Select the language and time by pressing “Up/Down”.
Confirm your selection by pressing “OK”; press “Up/Down” to
change the language or time; confirm the language and time with
“OK”.
If you have accidentally made an incorrect
choice of language...
...you can reset as follows:
- turn the programme selector knob to “Settings”;
- press the “Reset” button;
- turn the selector switch marking to the top and then back to
Settings.
The desired language can now be selected.
 UPDPOGJSN
4FUDMPDL
4FUDPOUSBTU
4FUMBOHVBHF
Up
Down
Please follow
the instructions
on the LCD display
Set language
Set time
In the same way, you can adjust contrast and brightness as well as
switching the buzzer and child safety on and off.
Important Note
Please refer to the installation instructions enclosed in the
appliance.
*UBMJBOP
%FVUTDI
 UPDPOGJSN
&OHMJTI
&OHMJTIDPOGJSNFE
 UPDPOGJSN
4FUMBOHVBHF
4FUDPOUSBTU
4FUDMPDL
5PTFUUJNF
5PDPOGJSN

"55&/5*0/
EJEZPVSFNPWF
USBOTQPSUCSBDFT
5PDPOGJSN
Set Child safety
Turn the programme selector knob to “Settings”.
Select “Set Child safety” and confirm with “OK”.
With the child safety activated, you can select a wash programme
and run it, but you cannot change or cancel it while it is running.
If you want to cancel or change a running programme, you can
temporarily release the child safety by pressing simultaneously.
You can then select or run a new programme. While this
programme is running, the child safety device is re-activated in
order to prevent accidental programme changes.
For fault messages, please read through the enclosed “Instructions
for Use” (“Troubleshooting Guide”).
To deactivate Child safety:
- turn the programme selector knob to “Settings”;
-select “Set Child safety” by pressing “Up/Down”, confirm
selection by pressing “OK”;
- on the LCD display “Off” is flashing - confirm deactivation of
child safety by pressing “OK”.
,
5PDPOGJSN
4FU#SJHIUOFTT
4FU#V[[FS
4FU$IJMETBGFUZ
and
3gb05600a.fm Page 1 Wednesday, October 6, 2004 4:05 PM
Black process 45.0° 100.0 LPI
GB
5019 301 05600/A
Whirlpool is a registered trademark of Whirlpool USA
Select and start
wash programme
Turn the programme selector knob with the marking to highlight
the desired programme.
It will appear on LCD display with the preset speed and
temperature. You can now start the wash programme, or change
the temperature and spin speed and, if required, select additional
options.
Press the “Menu” button to select additional functions (please follow
the instructions on the LCD display). The additional options you can
choose are displayed as symbols on the LCD display:
As soon as you have selected the desired additional options, you
can start the wash programme, by pressing the flashing Start
symbol on the programme selector knob. For that, you must not
go to the end of the selection displayed on the LCD display.
End of cycle
&BTZDBSF
1VTI PS
 xD
Pre-
Intensive
Rinse
Rinse hold
Extra care
Easy
Iron
Wash
&/%0'$:$-&
 xD
Button functions
Press the “Menu” button to call up the next screen.
Activate or deactivate additional options and set the spin speed
and/or temperature with the “Up/Down” arrow buttons.
Confirm with “OK”.
Press the “Back” button to return to the previous screen.
Press the “Info” button to obtain additional information
.
Press the “Reset” button:
- to cancel a running wash program;
- to cancel changes to a selected programme (e.g. change of
temperature, selected options) before the programme has been
started;
- to cancel a wash programme stored under “Memory”.
Storing frequently used wash
programmes
Turn the programme selector knob to “Memory”.
With the arrow buttons, select a free storage space (from M1 to
M10) and confirm with “OK”.
Select the required programme from the list of wash programmes
displayed and confirm with “OK”. As already described, you can
change the wash temperature and spin speed and select additional
options as desired.
Confirm with “OK” at the end of the displayed selection.
The wash programme will then be stored in the selected storage
space and can be selected again at any time.
Cancelling stored wash programmes
- Turn the programme selector knob to “Memory”;
- With the arrow buttons, select the stored wash programme to
be cancelled;
- Press the “Reset” button and hold the button down for a few
seconds, until “Empty” appears next to the storage space in
question.
,
5PTFMFDU
.FNQUZ
.FNQUZ
.FNQUZ
,
5PTFMFDU
&BTZDBSF
%BJMZMPBE
$PUUPO
,
5PTFMFDU
.FNQUZ
.FNQUZ
.&BTZDBSF x$
3gb05600a.fm Page 2 Wednesday, October 6, 2004 4:05 PM
Black process 45.0° 100.0 LPI
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Whirlpool AWO 9166 Program Chart

Category
Washing machines
Type
Program Chart

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI