Page is loading ...
AUTOMATIC SOAP DISPENSER
16.9 FLUID OUNCE CAPACITY
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
Copyright
©
2005 by Harbor Freight Tools
®
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
®
TO HELP PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
Model 93140
PRODUCT SPECIFICATIONS
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep this manual and invoice in a safe and dry place for future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed in this
manual may result in serious injury.
SAVE THESE INSTRUCTIONS
SKU 93140
PAGE 2For technical questions, please call 1-800-444-3353.
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists on page 7
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
IMPORTANT SAFETY INSTRUCTIONS
Item Description
Electrical Requirements Requires 4 “AA” batteries (not included)
Product Compatibility May be used with liquid soap, shampoo, or lotion
* See Warnings
Storage Capacity Approximately 16.9 Fluid ounces
Infra-red Sensor Range Approximately 1/2” to 4”
Dimensions 8-1/2” High x 5-1/2” Deep x 7-1/4” Wide
Additional Features May be used with stand or mounted on wall
Unit Weight 1.50 Pounds
SKU 93140 For technical questions, please call 1-800-444-3353. PAGE 3
1. This product is designed for use with liquid soap, shampoo, or lotion only.
Never use chemicals or other toxic liquids.
2. Always wear eye protection. Wear ANSI approved safety impact
goggles when assembling and installing this product.
3. Do not force the product. Use the correct product for your application. The
correct product will do the job better and safer at the rate for which it is
designed.
4. Remove the batteries from the Soap Dispenser before making any
adjustments, changing accessories, or storing the unit. Such preventive
safety measures reduce the risk of starting the unit accidentally.
5. Check for misalignment or binding of moving parts, broken parts, and any
other condition that may affect the Soap Dispenser’s operation. If
damaged, have the unit serviced before using.
6. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one Soap Dispenser may become
hazardous when used on another Soap Dispenser.
7. Product service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in
a risk of injury.
8. When servicing the Soap Dispenser, use only identical replacement parts.
Follow instructions in the
“Inspection, Maintenance, And Cleaning”
section
of this manual. Use of unauthorized parts or failure to follow maintenance
instructions may create a risk of electric shock or injury.
9. Maintain labels and nameplates on the Soap Dispenser. These carry
important information. If unreadable or missing, contact Harbor Freight Tools for
a replacement.
10. Use the right product for the job. There are certain applications for which this
product was designed. Do not use small equipment, tools, or attachments to do
the work of larger industrial equipment, tools, or attachments. Do not use this
product for a purpose for which it was not intended.
11. WARNING! The warnings and cautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.
SKU 93140 For technical questions, please call 1-800-444-3353. PAGE 4
ASSEMBLY INSTRUCTIONS
To Assemble As A Self-Standing Unit:
1. Attach the Stand (4) to the rear of the Base (5). (See Figure A.)
2. Insert the Body (2) onto the top of the Stand (4). Then, secure the Body to the
Stand using the Stand Screw (7). (See Figure A.)
STAND (4)
BASE (5)
BODY (2)
BASE (5)
STAND (4)
BODY (2)
STAND SCREW (7)
1. NOTE: The Soap Dispenser may be assembled and used either as a
self-standing
unit or as a
wall mounted
unit:
LID (1)
BATTERY COVER (3)
SKU 93140 For technical questions, please call 1-800-444-3353 PAGE 5
To Assemble As A Wall Mounted Unit:
1. Place the Wall Mount (6) at the desired location against the wall and use the Wall
Mount as a template to mark the position of two 1/4” diameter holes to be drilled.
(See Figure B.)
2. Drill two 1/4” diameter holes and insert the Wall Plugs (9) in the holes.
CAUTION: When drilling holes always first make sure no electrical cables or
wires are in the drilling path. Then, secure the Wall Mount (6) to the wall using
two Wall Mount Screws (8).(See Figure B.)
3. Slide the Body (2) of the Soap Dispenser downward onto the Wall Mount (6).
(See Figure B.)
To Install Batteries:
1. Remove the Battery Cover (3) from the Body (2) of the Soap Dispenser to expose
the Battery Compartment. Install four “AA” alkaline batteries, making sure the
polarity (“+” and “--”) of the batteries match that as shown in the Battery
Compartment. Then, replace the Battery Cover. (See Figure A.)
OPERATING INSTRUCTIONS
1. Raise the Lid (1) of the Soap Dispenser and fill the unit with up to 16.9 fluid
ounces of liquid soap, shampoo, or lotion. Then, close the Lid. (See Figure A.)
2. Place your hand under the Sensor located on the underside of the Body (2) to
automatically dispense the liquid soap, shampoo, or lotion. NOTE: When the
WALL MOUNT (6)
BODY (2)
WALL PLUG (9)
WALL MOUNT SCREW (8)
FIGURE B
Soap Dispenser is new it is full of
air pockets
inside the pump system. When you
use the Soap Dispenser for the first time or just after the replacement of liquid
soap, shampoo, or lotion, the unit needs to be automatically turned on several
times to fill those air pockets with liquid soap, shampoo, or lotion.
Note: If the dispenser fails to work properly, always check batteries; they may
need to be replaced.
INSPECTION, MAINTENANCE, AND CLEANING
1. CAUTION! Always make sure the Soap Dispenser’s batteries are removed
prior
to performing any inspection, maintenance, or cleaning of the unit.
2. Before each use, inspect the general condition of the Soap Dispenser. Check
for clogging throughout the system, misalignment or binding of moving parts,
damaged or leaking batteries, and any other condition that may affect its safe
operation. If abnormal noise or vibration occurs, have the problem corrected
before further use. Do not use damaged equipment.
3. When replacing batteries, never attempt to incinerate batteries as they may
explode. Dispose of old batteries according to local solid waste authority
guidelines.
4. When cleaning, wipe the exterior of the Soap Dispenser with a damp, clean
cloth. Do not introduce water or any other liquid into the interior of the Body.
5. CAUTION! All maintenance, service, or repairs not listed in this manual
should only be performed by a qualified service technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 93140 For technical questions, please call 1-800-444-3353 PAGE 6
PARTS LIST AND ASSEMBLY DIAGRAM
SKU 93140 For technical questions, please call 1-800-444-3353. PAGE 7
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
1
2
3: BATTERY COVER NOT SHOWN
6: WALL MOUNT NOT SHOWN
7: STAND SCREW NOT SHOWN
8: WALL MOUNT SCREWS NOT SHOWN
9: WALL PLUGS NOT SHOWN
4
5
Part # Description Qt
y
. Part # Description Qt
y
.
1 Lid 1 6 Wall Mount 1
2 Body 1 7 Stand Screw 1
3 Battery Cover 1 8 Wall Mount Screw 2
4 Stand 1 9 Wall Plug 2
5 Base 1
/
