De Dietrich ALEZIO - AWHP MIV-II Owner's manual

Brand: De Dietrich

Model: ALEZIO - AWHP MIV-II

Category: Heat pumps

Type: Owner's manual

This manual is also suitable for

ALEZIO AWHP MIV-II

ALEZIO

Reversible air / water heat pump "Split Inverter"

AWHP MIV-II

User Guide

300023321-001-03

Contents

1 Introduction ................................................................................................4

1.1 Symbols used .......................................................4

1.1.1 Symbols used in the manual ...................................4

1.1.2 Symbols used on the equipment .............................4

1.2 Abbreviations and lexicon ...................................5

1.3 General ..................................................................5

1.3.1 Manufacturer’s liability .............................................5

1.3.2 Installer’s liability .....................................................5

1.3.3 User’s liability ..........................................................6

2 Safety instructions and recommendations ..............................................7

2.1 Safety instructions ...............................................7

2.2 Recommendations ................................................7

3 Description ..................................................................................................9

3.1 General description ..............................................9

3.2 Control panel .......................................................10

3.2.1 Description ............................................................10

3.2.2 Description of the display ......................................10

4 Operating the appliance ..........................................................................12

4.1 Starting and stopping the heat pump ...............12

4.1.1 Starting the heat pump ..........................................12

4.1.2 Switching off the central heating ...........................14

4.2 Information menu display ..................................14

4.2.1 Reading out measured values ..............................15

4.2.2 Energy consumption display .................................15

4.3 Changing the user parameters ..........................16

4.3.1

Modifying the set room temperature dH ...............17

4.3.2 Modifying the domestic hot water

temperatureHr .....................................................17

4.3.3 Changing the operating mode ...............................18

4.3.4 Forcing the additional heating ...............................18

4.3.5 Hybrid operating mode ..........................................19

23/04/2013 - 300023321-001-03

5 Checking and maintenance .....................................................................21

5.1 General instructions ...........................................21

5.2 Periodic checks ..................................................21

5.3 Top up the installation with water .....................22

5.4 Bleeding the heating system .............................22

5.4.1 Manual venting ......................................................23

5.4.2 Automatic venting ..................................................23

6 Troubleshooting .......................................................................................24

6.1 Error messages ...................................................24

6.2 Incidents and solutions ......................................25

7 Technical specifications ..........................................................................27

7.1 Technical specifications ....................................27

7.1.1 Heat pump .............................................................27

8 Energy savings .........................................................................................29

8.1 Energy savings ...................................................29

8.1.1 Energy-saving advice ............................................29

8.1.2 Room thermostat and settings ..............................29

9 Warranty ....................................................................................................30

9.1 General ................................................................30

9.2 Warranty terms ...................................................30

Contents

23/04/2013 - 300023321-001-03

1 Introduction

1.1 Symbols used

1.1.1. Symbols used in the manual

In these instructions, various danger levels are employed to draw the

user’s attention to particular information. In so doing, we wish to

safeguard the user’s safety, obviate hazards and guarantee correct

operation of the appliance.

DANGER

Risk of a dangerous situation causing serious physical

injury.

WARNING

Risk of a dangerous situation causing slight physical

injury.

CAUTION

Risk of material damage.

Signals important information.

¼Signals a referral to other instructions or other pages in the

instructions.

1.1.2. Symbols used on the equipment

Protective earthing

Alternating current

Before installing and commissioning the device, read

carefully the instruction manuals provided.

Dispose of the used products in an appropriate recovery

and recycling structure.

This appliance must be connected to the protective earth.

D000241-C

AWHP MIV-II

1. Introduction

23/04/2013 - 300023321-001-03

Caution: danger, live parts.

Disconnect the mains power prior to any operations.

1.2 Abbreviations and lexicon

4 MIV: Indoor module

4 HP: Heat pump

4 DHW: Domestic hot water

4 Flow temperature: Temperature of the water circulating in the

radiators or in the underfloor heating

4 Ambient temperature: Temperature inside the house or in a room

4 Room temperature setpoint: Temperature programmed in the

control system that must be reached by the heat pump

4 Forced back-up operation: Function enabling the ignition of a

heating system to complement the heat pump in periods of

extreme cold

1.3 General

1.3.1. Manufacturer’s liability

Our products are manufactured in compliance with the requirements

of the various applicable European Directives. They are therefore

delivered with [ marking and all relevant documentation.

In the interest of customers, we are continuously endeavouring to

make improvements in product quality. All the specifications stated in

this document are therefore subject to change without notice.

It is our responsibility to inform customers, in accordance with Article

L. 113-3 of the Consumer Code, of their obligation to have this

equipment installed by a certified operator whenever the refrigerant

load is more than two kilograms or when a refrigerant connection is

necessary (the case with split systems, even when fitted with a quick

coupling device).

Our liability as the manufacturer may not be invoked in the following

cases:

4 Failure to abide by the instructions on using the appliance.

4 Faulty or insufficient maintenance of the appliance.

4 Failure to abide by the instructions on installing the appliance.

1.3.2. Installer’s liability

The installer is responsible for the installation and inital start up of the

appliance. The installer must respect the following instructions:

4 Read and follow the instructions given in the manuals provided

with the appliance.

1 2

M002628-A

1. Introduction

AWHP MIV-II

23/04/2013 - 300023321-001-03

4 Carry out installation in compliance with the prevailing legislation

and standards.

4 Perform the initial start up and carry out any checks necessary.

4 Explain the installation to the user.

4 If a maintenance is necessary, warn the user of the obligation to

check the appliance and maintain it in good working order.

4 Give all the instruction manuals to the user.

1.3.3. User’s liability

To guarantee optimum operation of the appliance, the user must

respect the following instructions:

4 Read and follow the instructions given in the manuals provided

with the appliance.

4 Call on qualified professionals to carry out installation and initial

start up.

4 Get your installer to explain your installation to you.

4 Have the required checks and services done.

4 Keep the instruction manuals in good condition close to the

appliance.

This appliance is not intended to be used by persons (including

children) whose physcial, sensory or mental capacity is impaired or

persons with no experience or knowledge, unless they have the

benefit, through the intermediary of a person responsible for their

safety, of supervision or prior instructions regarding use of the

appliance. Care should be taken to ensure that children do not play

with the appliance.

To prevent hazardous situations from arising, if the mains lead is

damaged it must be replaced by the original manufacturer, the

manufacturer’s dealer or another suitably skilled person.

AWHP MIV-II 1. Introduction

23/04/2013 - 300023321-001-03

2 Safety instructions and

recommendations

2.1 Safety instructions

DANGER

If smoke is released or in case of refrigerant leak:

1. Switch the appliance off.

2. Open the windows.

3. Evacuate the premises.

4. Contact a qualified professional.

WARNING

Depending on the settings of the appliance:

4 The temperature of the radiators may reach 80°C.

4 Do not touch the refrigeration connection pipes with

your bare hands while the appliance is running.

Danger of burns or frost injury.

CAUTION

Do not neglect to service the appliance. Contact a qualified

professional or take out a maintenance contract for the

annual servicing of the appliance.

2.2 Recommendations

WARNING

Only qualified professionals are authorised to work on the

appliance and the installation.

4 Regularly check that the water pressure in the installation is

between 1,5 and 2 bar.

4 Ensure that the appliance is accessible at all times for

maintenance purposes.

4 Avoid draining the installation.

4 Use only original spare parts.

4 Never remove or cover labels and rating plates affixed to the

appliance. Labels and rating plates must be legible throughout the

entire lifetime of the appliance.

4 To guarantee the following functions, select the Off/Antifreeze

mode but do not switch off the appliance:

- Anti blocking of pumps

2. Safety instructions and recommendations

AWHP MIV-II

23/04/2013 - 300023321-001-03

- Antifreeze protection

AWHP MIV-II 2. Safety instructions and recommendations

23/04/2013 - 300023321-001-03

3 Description

3.1 General description

The ALEZIO heat pump comprises:

4 An outside module for energy production in hot mode only when

it is combined with an uninsulated inside module.

4 A reversible outside module for energy production in hot or cold

mode when it is combined with an insulated inside module

4 An inside module with a control panel to handle the thermal

exchange between the R410A fluid and the hydraulic circuit

The two units are connected by means of refrigeration and electrical

connections.

The system offers the following advantages:

4 The heating circuit is housed in the insulated volume within the

home. There is no danger of the pipes freezing.

4 Thanks to the DC inverter system, the heat pump modulates its

output to adapt to the needs of the home.

4 The control panel uses the outside temperature sensor to adjust

the temperature of the heating circuit according to the outside

temperature.

3. Description AWHP MIV-II

23/04/2013 - 300023321-001-03

3.2 Control panel

3.2.1. Description

Display

On/Off switch

Pressure gauge

Confirm key S or K

T DHW temperature button r or +

Y Heating temperature button d or -

Key > [Escape]

Back-up forcing button

Menu key

3.2.2. Description of the display

The display shows the operating status of the heat pump, the heating

flow temperature and any error codes.

M002226-B

6 5 4

2 3

AWHP MIV-II

3. Description

23/04/2013 - 300023321-001-03

Menus

4 Q: Information menu display

4 W: User menu

4 ?: Installer’s settings

Operating modes

4 r: Domestic hot water mode

4 w: Cooling mode (Only in reversible versions)

4 p: Stop/Antifreeze mode

4 b: Heating mode

4 v: Compressor on

4 G: Additional heating on, stage 1-2

Forced back-up operation

4 m + d: Heating

4 m + r: DHW

4 m + d + r: Heating + DHW

Other information

4 a: Default active

4 dHr: Adjusting the setpoint temperatures

4 K: A manual vent cycle is running / Permanent

display of the Information menu / The screed drying

function is active

M002227-B

3. Description AWHP MIV-II

23/04/2013 - 300023321-001-03

4 Operating the appliance

4.1 Starting and stopping the heat pump

4.1.1. Starting the heat pump

WARNING

Only a qualified professional may carry out initial start up

or a start up when the heat pump has completely stopped.

Start the heat pump to produce heating, domestic hot water or

cooling (Cooling mode: Only in reversible versions).

To restart the heat pump that is in off/antifreeze mode, perform the

following operations:

1. Press button

2 times to modify the operating mode.

See chapter: "Changing the operating mode", page 18.

2. Press the

key to confirm and exit the menu.

If no buttons are pressed, the settings menus are exited

automatically after 10 seconds, without saving the

parameters.

Press the key

to exit the menu.

The following information is displayed and tells you which operating

mode the heat pump is set to:

M002239-B

M002249-B

AWHP MIV-II 4. Operating the appliance

23/04/2013 - 300023321-001-03

Operating mode Screen display

Heating and domestic hot water

M002290-A

Heating

M002289-A

Domestic hot water

M002293-A

Cooling and domestic hot water

M002292-A

Cooling

M002291-A

4. Operating the appliance AWHP MIV-II

23/04/2013 - 300023321-001-03

Operating mode Screen display

Stop/Antifreeze mode

M002288-A

Pool

M002289-A

Swimming pool and domestic hot water

M002290-A

4.1.2. Switching off the central heating

It is possible to shut down the central heating and select an operating

mode suited to the situation and the desired comfort level:

4 In summer, by using comfort, it is possible to operate cooling w

(Only in reversible versions).

4 In the event of a prolonged absence (weekend, holiday), it is

possible to switch to shutdown/frost protection mode .

4 It is possible to prepare domestic hot water r all year round.

4.2 Information menu display

To display the data in the Information menu, proceed as follows:

1. Press the

key.

M002246-B

AWHP MIV-II

4. Operating the appliance

23/04/2013 - 300023321-001-03

2. The symbol

flashes.

Press the

key.

3. The information SERVICE flashes for 5 seconds.

If no buttons are pressed for 10 seconds, the screen goes back to

the main display.

To stay in the Information menu, press the

button, the

information SERVICE no longer flashes.

4. Use the - and + keys to scroll through the information.

5. Press the key

to exit the menu.

4.2.1. Reading out measured values

Parameter

Description Unit

t1:

4 In heating mode: Heating flow set point temperature

4 In DHW mode: DHW setpoint temperature

4 In cooling mode: Cooling setpoint temperature

4 In swimming pool mode: Pool set temperature

°C

t2: Measured start temperature °C

t2: Domestic hot water temperature measured °C

t2: Outside temperature measured °C

lt: Water flow Litres/minute

S;ft

Software version

4.2.2. Energy consumption display

Parameter

Description Unit

c1:

Estimated consumption of electrical energy in heating mode

(1)

kWh

c2:

Estimated consumption of electrical energy in DHW mode

(1)

kWh

c3:

Estimated consumption of electrical energy in cooling mode

(1)

(2)

kWh

(1) Display available if the estimated electrical energy consumption function is activated

(2) Cooling mode must be enabled

M002247-C

M002278-C

M002248-C

4. Operating the appliance AWHP MIV-II

23/04/2013 - 300023321-001-03

The estimated electricity consumption is displayed in 3 digits. The

fourth digit indicates the scale (x1, x10, x100, x1000).

Display example Description

C004232-B

The displayed value is 123 kWh. The unit is 1 kWh.

C004233-B

The displayed value is 1230 kWh. The unit is 10 kWh. The fourth digit indicates

the scale x10. Only the first 3 figures are displayed.

C004234-B

The displayed value is 12300 kWh. The unit is 100 kWh. The fourth digit

indicates the scale x100. Only the first 3 figures are displayed.

C004235-B

The displayed value is 123000 kWh. The unit is 1000 kWh. The fourth digit

indicates the scale x1000. Only the first 3 figures are displayed.

4.3 Changing the user parameters

If no buttons are pressed, the settings menus are exited

automatically after 10 seconds, without saving the

parameters.

AWHP MIV-II 4. Operating the appliance

23/04/2013 - 300023321-001-03

4.3.1.

Modifying the set room temperature dH

1. Press the

key.

2. Press the + or - keys to change the value.

Temperature

Adjustment range Increment Factory

setting

Room temperature

setpoint

from 15 to 30°C 1 °C 20 °C

3. Press the

key to confirm and exit the menu.

When a room thermostat is connected, set the room

thermostat to a value 2 K higher than the room temperature

setpoint dH.

4.3.2. Modifying the domestic hot water

temperatureHr

1. Press the

key.

2. Press the + or - keys to change the value.

Temperature

Adjustment range Increment Factory setting

DHW set temperature from 40 to 65°C 1 °C 50 °C

3. Press the

key to confirm and exit the menu.

M002240-B

M002241-B

M002243-B

M002244-B

4. Operating the appliance

AWHP MIV-II

23/04/2013 - 300023321-001-03

4.3.3. Changing the operating mode

1. Press the

key 2 times.

2. When the symbol

flashes on the display, press the

button.

3. Press the + or - keys to change the value (See table below).

4. Press the

key to confirm and exit the menu.

Operating mode

Value Screen display

Heating and domestic hot water 1

b + r

Heating 2

Domestic hot water 3

Cooling and domestic hot water

(1)

w + p + r

Cooling

(1)

w + p

Stop/Antifreeze mode 6

Pool 7

Swimming pool and domestic hot water 8

b + r

(1) Only in reversible versions

4.3.4. Forcing the additional heating

It is impossible to force the additional heating when the off/

antifreeze mode is selected.

It is possible to force use of the additional heating to complement the

heat pump. To force use of the additional heating, perform the

following operations:

1. Press keys

and

simultaneously.

M002249-B

M002250-B

M002251-B

M002261-C

AWHP MIV-II

4. Operating the appliance

23/04/2013 - 300023321-001-03

2. Hold the

key down and press the

key successively to

choose the forcing desired.

Display Back-up

Forcing additional heating for heating

Forcing additional heating for DHW

Forcing additional heating for heating and

DHW

The

symbol disappears from

the display

Additional heating forcing deactivated

4.3.5. Hybrid operating mode

CAUTION

The hybrid operating mode is only available for appliances

with hydraulic back-up.

The appliance offers a choice between several hybrid operating

modes. The modes available offer either optimised energy

consumption according to energy cost, or optimised energy

consumption according to primary energy consumption. Both hybrid

operating modes are available via parameter U1. In optimised

primary energy consumption mode, the control system chooses the

generator that consumes the least primary energy. In optimised

energy cost mode, the control system chooses the cheapest

generator according to the coefficient of performance of the heat

pump and according to energy cost.

To access the parameters:

Press the

key 3 times.

The symbol

flashes.

Press the key

to enter the "Installer" menu.

3. Use the + and - keys to switch from one parameter to another.

4. Use the + and - keys to change the parameter value.

Press the

key to confirm the setting.

To modify another parameter, repeat the procedure from

step 3.

M002264-D

M002253-B

M002254-B

4. Operating the appliance AWHP MIV-II

23/04/2013 - 300023321-001-03

Page is loading ...

De Dietrich ALEZIO - AWHP MIV-II Owner's manual

Brand: De Dietrich

Model: ALEZIO - AWHP MIV-II

Category: Heat pumps

Type: Owner's manual

This manual is also suitable for

ALEZIO AWHP MIV-II

Download PDF

report

De Dietrich ALEZIO - AWHP MIV-II Owner's manual

This manual is also suitable for

De Dietrich ALEZIO - AWHP MIV-II Owner's manual

Related papers

Other documents