Regency Fireplace Products HZ33CE Owner's manual

HZ33CE
Brand
Regency Fireplace Products
Model
HZ33CE
Category
Thermostats
Type
Owner's manual
9.957.035 05
PROFLAME GTMF SYSTEM
USE AND INSTALLATION INSTRUCTIONS
Read the instructions before use. This control must be installed in accordance with the rules in force.
English -
12
2
2
ENGLISH
The Proflame GTMF is a modular remote control system that directs the functions
of a hearth appliance. The Proflame GTMF is configured to control the on/off
main burner operation, its flame levels and provides on/off and Smart
thermostatic control of the hearth appliance. The system controls a remotely
actuated 120V/60Hz power outlet, fan speed through six (6) levels and has a
constantly powered 120V/60Hz power outlet. Comfort control is advanced by the
Smart thermostat
3
Remote Control
Supply voltage 4.5 V (three 1.5 V AAA batteries)
Ambient temperature ratings 0 - 50 °C (32 - 122 °F)
Radio frequency 315 MHz
Receiver
Supply voltage 6.0 V (four 1.5 V AA batteries)
Ambient temperature ratings 0 - 60 °C (32 - 140 °F)
Radio frequency 315 MHz
Fan Control Module
Supply voltage/frequency: 120 V / 60 Hz
Ambient temperature ratings: 0 to 60 °C (32 to 140 °F)
Three wires bus: two wires to provide DC voltage to the receiver;
one wire gives uni-directionally signal from the receiver
Output voltage/frequency/current: 120 V / 60 Hz / 5 A
Aux switched output: 120 V / 60 Hz / 2 A
Fan speed output: 120 V / 60 Hz / 1 A
TECHNICAL DATA
ENGLISH
WARNING
THE TRANSMITTER AND RECEIVER ARE RADIO FREQUENCE DEVICES.
PLACING THE RECEIVER IN OR NEAR METAL MAY SEVERELY REDUCE THE SIGNAL
RANGE.
ATTENTION!
- TURN “OFF” THE MAIN GAS SUPPLY OF THE APPLIANCE DURING INSTALLATION
OR MAINTENANCE OF THE RECEIVER.
- PLACE THE RECEIVER’S 3 POSITION SLIDER SWITCH IN THE “OFF” POSITION
DURING INSTALLATION OR MAINTENANCE.
- TURN “OFF” MAIN GAS SUPPLY TO THE APPLIANCE PRIOR TO REMOVING OR
REINSERTING THE BATTERIES IN THE RECEIVER.
- DURING APPLIANCE INSTALLATION/MAINTENANCE OR IN CASE OF REMOTE
CONTROL MALFUNCTION TURN OFF THE FAN CONTROL MODULE USING THE
“ON/OFF” MAIN POWER SWITCH ON THE FRONT PANEL OF THE FCM.
The Proflame Remote Control System consists of three elements:
1. Proflame Transmitter.
2. Proflame Receiver and a wiring harness to connect the Receiver to the gas valve, stepper
motor and Fan Control Module.
3. Proflame Fan Control Module (FCM)
The Proflame Transmitter uses a streamline design with a simple button layout and informative
LCD display (Fig. 1).
The Transmitter is powered by 3 AAA type batteries.
A Mode Key is provided to Index between the features and a Thermostat Key is used to turn
on/off or index through Thermostat functions (Fig. 1 & 2).
TRANSMITTER (Remote Control with LCD Display)
SYSTEM DESCRIPTION
4
ENGLISH
Fig. 1: PROFLAME Transmitter.
Blue LCD display
UP/DOWN Arrow Key
ON/OFF Key
THERMOSTAT Key
MODE Key
Low battery alarm
Child safety lock-out
Room
Temperature
Aux ON
Set Point
Temperature/Level/State
Flame ON
Thermostat
OFF/ON/SMART
Fan
Fig. 2: Transmitter LCD display.
Transmission
Fan Control Module (FCM) offers the added ability to control the fan speed through six (6)
speeds, a remotely actuated 120V outlet and a constantly powered 120V outlet. The FCM
provides DC power to the Receiver allowing the batteries to be used only when line power is
interrupted or lost (Fig.4).
The Proflame Receiver (Fig. 3) connects directly to the gas valve and stepper motor and Fan
Control Module with a wiring harness. The Receiver is powered by 4 AA type batteries. The
Receiver accepts commands via radio frequency from the Transmitter to operate the appliance
in accordance with with the particular Proflame system configuration. The Receiver three
position slider switch can be set to one of three positions: ON (Manual Override), Remote
(Remote control) or Off.
5
ENGLISH
3 Positions Slider
PRG Key
Fig. 3: Proflame Receiver body.
12 PIN terminal
Fig. 4: Fan Control Module.
MAINS VOLTAGE
SUPPLY CORD
MODULE ON/OFF SWITCH
COMMUNICATION BUS (3 PIN)
FAN OUTLET PLUG
MAINS VOLTAGE PLUG
AUX OUTLET PLUG
FAN CONTROL MODULE
RECEIVER
INSTALLATION
Receiver
The receiver can be placed inside a standard Junction type wall box or a low temperature area
of the appliance.
Wall Mounting
1. Connect the wiring harness to the back of the Receiver.
6
ENGLISH
2. Install the Receiver in the Junction box using
the existing J box screws. (Fig. 4)
3. Insert the 4 AA type batteries in the battery
compartment with the correct polarity.
4. Place the slider into the cover plate.
5. Put the Receiver switch in the “OFF” position.
6. Make sure the Receiver and cover plate
words “ON”and “UP” are on the same side.
7. Align the slider with the switch on the
Receiver and couple the switch into the slider.
8. Align the screw holes.
9. Using the two (2) screws provided secure the cover plate to the Receiver.
Hearth Mounting
1. Connect the wiring harness to the back of the Receiver.
2. Install the 4 AA type batteries in the battery compartment with the correct polarity.
3. Make sure the Receiver and cover plate words “ON”and “UP” are on the same side.
4. Place the slider into the cover plate.
5. Align the slider with the switch on the Receiver and couple the switch into the slider.
6. Using the two (2) screws provided secure the cover plate to the Receiver.
Fig. 4
Fan Control Module
The FCM can be placed in a low temperature area of the appliance.
Connecting to the Gas Valve and FCM
The wiring harness for the Proflame GTM system has two wires labeled “TH” & “TPTH”. Connect
the wires to the gas valve as labeled. (TH to TH and TPTH to TPTH). Additionally there are
connectors labeled “Motor” and “COM”. Connect the “Motor” connector to the stepper motor
on the gas valve. Connect the “COM” connector to the Fan Control Module connection labeled
“COM” (Fig. 5).
REMOTE
REMOTE
TP
TH
TPTH
MOTOR
RECEIVER
FCM-COM
Green
Whi
te
Red
Black
(+)
(-)
120
V OUT
Fig. 5: Wiring diagram.
ENGLISH
OPERATING PROCEDURE
Initializing the System for the first time
Install the 4 AA batteries into the receiver battery bay. Note the polarity of the battery and
insert into the battery bay as indicated on the Battery cover (+/-). Place the 3 position slider
switch in the “Remote” position. (fig. 3) Using the end of a paper clip, or other similar object,
insert the end of the paper clip into the hole marked “PRG” on the Receiver front cover (fig 3).
The Receiver will “beep” three (3) times to indicate that it is ready to synchronize with a
Transmitter. Install the 3 AAA type batteries in the Transmitter battery bay, located on the
base of the Transmitter. With the batteries already installed in the Transmitter, push the On
button. The Receiver will “beep” four times to indicate the Transmitter’s command is accepted
and sets to the particular code of that Transmitter. The system is now initialized.
Fig. 7: Remote Control display.
Temperature indication Display
With the system in the “OFF” position, press the Thermostat Key and the Mode Key at the same
time. Look at the
LCD screen on the
Transmitter to verify
that a C or F is visible
to the right of the
Room Temperature
display. (Fig. 6)
Fig. 6: Remote Control display in Farenheit and Celsius.
Turn on the Appliance
Press the ON/OFF Key on the Transmitter. The Transmitter display will show all active Icons on the
screen. At the same time the Receiver connects the thermopile to the gas valve millivolt coil and
the appliance main burner turns on. A single “beep” from the Receiver will confirm reception of
the command.
Turn off the Appliance
Press the ON/OFF Key on the Transmitter. The Transmitter LCD display will only show the room
temperature and Icon (Fig. 7). At the same time the Receiver disconnects the thermopile from
the gas valve millivolt coil and the appliance burner turns off. A single “beep” from the Receiver
confirms reception of the command.
7
8
ENGLISH
Remote Flame Control
The proflame GTMF has six (6) flame levels. With the system on, and the flame level at the
maximum in the appliance, pressing the Down Arrow Key once will reduce the flame height by
one step until the flame is turned off.
The Up Arrow Key will increase the flame height each time it is pressed. If the Up Arrow Key is
pressed while the system is on but the flame is off, the flame will come on in the high position.
( Fig. 8 & 9 ) A single “beep” will confirm reception of the command.
Fig. 10
Fig. 11
SET TEMPERATURE
ROOM TEMPERATURE
ROOM THERMOSTAT ( Transmitter Operation)
The Remote Control can operate as a room thermostat. The thermostat can be set to a desired
temperature to control the comfort level in a room.
To activate this function, press the Thermostat Key (Fig. 1). The LCD display on the Transmitter will
change to show that the room thermostat is “ON” and the set temperature is now displayed (Fig.
10). To adjust the set temperature, press the Up or Down Arrow Keys until the desired set
temperature is displayed on the LCD screen of the Transmitter.
Fig. 8: Flame Off Flame Level 1
Fig. 9: Flame level 5 Flame Level Maximum
9
ENGLISH
Fig. 14
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the flame height in accordance to the difference
between the set point temperature and the actual room temperatures. As the room
temperature gets closer to the set point the Smart Function will modulate the flame down.
To activate this function, press the Thermostat Key (Fig. 1) until the word "SMART" appears
to the right of the temperature bulb graphic (Fig. 12). To adjust the set temperature, press
the Up or Down Arrow Keys until the desidered set temperature is displayed on the LCD
screen of the Transmitter (Fig. 13).
Fig. 12: Smart flame function
Fig. 13
Fan Speed Control
If the appliance is equipped with a hot air circulating fan, the speed of the fan can be
controlled by the Proflame system. The fan speed can be adjusted through six (6) speeds. To
activate this function use the Mode Key (fig.1) to index to the fan control icon (Fig. 14). Use the
Up/Down Arrow Keys (Fig.1) to turn on, off or adjust the fan speed (fig. 15). A single “beep”
will confirm reception of the command.
Fig. 15
Transmitter
The life span of the remote control batteries depends on
various factors: quality of the batteries used, the number
of ignitions of the appliance, the number of changes to the
room thermostat set point, etc.
When the Transmitter batteries are low, a Battery Icon will
appear on the LCD display of the Transmitter (Fig. 19) before
all battery power is lost. When the batteries are replaced this
Icon will disappear.
Receiver
The life span of the Receiver batteries depends on various factors: quality of
the batteries used, the number of ignitions of the appliance, the number of
changes to the room thermostat set point, etc.
When the Receiver batteries are low, No “beep” will be emitted from the Receiver when it
receives an On/Off command from the Transmitter. This is an alert for a low battery condition
for the Receiver. When the batteries are replaced the “beep” will be emitted from the Receiver
when the ON/OFF Key is pressed (See Initialization of The System).
10
ENGLISH
Remote Actuated 120V Auxiliary Outlet
The auxiliary function controls the AUX power outlet on the Fan Control Module. To
activate this function use the Mode Key (fig. 1) to index to the AUX icon (fig. 16 & 17).
Pressing the Up Arrow Key will activate the outlet. Pressing the Down Arrow Key will turn
the outlet off. A single “beep” will confirm the reception of the command.
Fig. 16
Fig. 17
Fig. 19
This function will lock the keys to avoid unsupervised
operation.
To activate this function, press the MODE and UP Keys at the
same time (fig. 18).
To de-activate this function, press the MODE and UP Keys at
the same time.
Key lock
Fig. 18
LOW BATTERY P0WER DETECTION
11
ENGLISH
If the batteries of the Receiver or Transmitter are low or depleted, the appliance can be turned
on manually by sliding the three position slider switch on the Receiver to the ON position.
This will bypass the remote control feature of the system and the appliance main burner will
come on if the gas valve is in the “On” position.
MANUAL BYPASS OF THE REMOTE SYSTEM
CAUTION
Property Damage Hazard.
Excessive heat can cause property damage.
The appliance can stay lit for many hours. Turn off the appliance if it is not going to be
attended for any lenght of time.
Always place the Transmitter where children can not reach it.
WARNING
Fire Hazard. Can cause severe injury or death
The Receiver causes ignition of the appliance. The appliance can turn on suddenly. Keep
away from the appliance burner when operating the remote system or activating manual
bypass of the remote system.
WARNING
Shock Hazard. Can cause severe injury or death
This device is power by line voltage. Do not try to repair this device.
In no way is the enclosure to be tampered with or opened.
Disconnect from line voltage before performing any manteinance.
WARNING
Devices rated more than 5A shall not connected to the OUT receptacle.
Devices rated more than 1A shall not connected to the FAN receptacle.
Devices rated more than 2A shall not connected to the AUX receptacle.
PROFLAME Transmitter
PROFLAME Receiver
107
132
PROFLAME FCM
Hearth mounted
Wall mounted
140
37
71
DIMENSIONAL DRAWINGS
Dimensions are in millimeters
PRG
102
42
REMOTE
PRG
115
70
REMOTE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Regency Fireplace Products HZ33CE Owner's manual

HZ33CE
Brand
Regency Fireplace Products
Model
HZ33CE
Category
Thermostats
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents