Hyundai H-LEDVD19V10 User manual

Category
LCD TVs
Type
User manual

This manual is also suitable for

LED TV with built-in DVD player
Руководство по эксплуатации Instruction manual
H-LEDVD24V10
Телевизор цветного
изображения c
жидкокристаллическим
экраном и встроенным
DVD-проигрывателем
Zoom
Repeat
A-B
Step
Display
Program
Subtitle
Angle
MP3 operation
Intro
Title
Audio
Goto function
Disc menu operation
System setup
General setup
Audio setup
Dolby Digital setup
Preference setup
General information
Troubleshooting
Causes of interference
Accessories
Specifications
Table of contents
Before you start
Utilization of the product
Important safeguards
Installation
Wall mounting
Stand installation
Connection
Connection
Outdoor antenna connection
Other connections
Operation
Control elements
Front panel
Back panel
Remote controller
Changing the battery
General operations
Signal sources
Teletext operations
PC screen
OSD operation
Channel setting
Picture setting
Sound setting
Timer setting
Option setting
Screen setting
USB operation
General operations of file playback
DVD playback operation
Turn on/off DVD
Insert disc
Play the disc
Stop
Rewind/Fast forward
Previous/next track/chapter/title
Slow playback
2 3
Table of contents Before you start
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read
this manual carefully before connecting, operating and/or adjusting the product and keep
the manual for reference in the future.
2
3
3
3
4
4
4
5
5
5
5
6
6
6
6
7
7
8
8
8
9
9
9
10
10
10
10
10
11
11
11
11
12
12
12
12
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
13
14
14
14
14
15
15
15
16
16
17
2 3
Table of contents Before you start
If you want to dispose this product, do not mix it with general household waste. There is
a separate collection system for used electronic products in accordance with legislation
that requires proper treatment, recovery and recycling.
Please contact your local authorities for the correct method of disposal. By doing so,
you will ensure that your disposed product undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on the environment and human
health.
Utilization of the product
Important safeguards
• Before connecting the AC power cord
to the DC adapter outlet, make sure that
the voltage designation of the DC adapter
corresponds to the local electrical supply.
• Accessories include a DC adaptor RS-
330/120-S325. Do not use other adaptors with
this unit.
• Please unplug the power cord from the AC
outlet and contact a service center for repair
if following occurs: any obvious abnormality
appears in the unit, such as smoky, peculiar
smell or strange sound; liquid has been spilled or
other objects have fallen into the unit; no picture
or sound; cover or panel is broken; although you
have operated the unit following the operating
instructions, it still cannot work normally.
• This unit should only be connected to a
wall socket having grounding.
• Always disconnect the power cord and
antenna during a storm.
• Do not fix the power cord with a metal nail.
• Unplug the power cord from the AC outlet;
also unplug the signal cables from the input
ports when the unit is unused for long periods
of time.
• When unplugging the plug, always hold
the wide slot, do not touch the metal part, and
do not destroy, refit, twist, pull or roast the
power cord.
• Please contact the service center
immediately if you found that the core is
showed in the air or has been broken.
• Please replace the AC outlet if the metal
bolt cannot be inserted into the power socket
completely or it cannot be fastened even when
it was pushed in, otherwise, any accidents of
shocks and fires would happen.
• Never touch the antenna lie or power plug
if it stars to thunder.
• Do not touch the power plug with wet
hands.
• Do not use any non-rated power socket
with numerous devices jointed on one power
socket or cable device. The wire of non-
designated capacity may cause the fire due to
the generation of heat.
• All instructions must be read and
understood well before you operate the unit.
Heed all warnings and follow all instructions.
• Please use the accessories provided
by the manufacturer. Using inadequate
accessories may result in accidents.
• Please adjust the product through the
panel buttons or the remote controller, do
not remove the cover or attempt to service
the product by yourself. Do not disassemble
back cover and do not make maintenance by
yourself to avoid the electric shock.
• Over-press the panel may destroy the
product.
• Do not place the product on an unstable
cart, stand surface, tripod, bracket, or table.
The product may fall, causing serious accidents
as well as the damage to the product.
• Please place the product on a flat surface
Installation
Wall mounting
For wall mounting the back panel of this
unit is equipped with 4 screw holes (4 mm
diameter, 100 mm horizontal/vertical spread
distance). A wall-mount bracket should be
used for wall mounting (the bracket is not
included and should be acquired separately).
Manufacturer is not responsible for improper
mounting resulting in damage of the unit.
Stand installation
Place the TV on a solid flat surface. Use soft
material to place over the screen to avoid any
damage. Then position the stand on the below
angle and turn it anti-clockwise to ensure that
the stand is locked to the TV as shown below:
To disassemble the stand, lift the plastic tab as
shown in the middle picture below and then turn
the stand clockwise to unlock. To avoid breaking,
do not lift the plastic tab with too much force.
4
Before you start
in a well-ventilated location. Keep it away from
the burning-light, direct sunlight, vibration,
high-temperature and humidity.
• Do not place any vase, potted plant, cup,
medicine and any container with water on this
product. If the liquid is spilt, it may cause the
fire, electric shock or breakdown.
• Do not install it at the place on the strong
magnetic field or current field. It may cause
break down. This equipment may be observed
deterioration of the picture by electromagnetic
radiation in electromagnetic environment.
• Fasten the wheel of the product or shelf
with wheels when installing this product. If it
moves or is tipped over, it may be damaged.
• Do not place any fire source such as
candlelight close to this product or place it on
this product. If it is tipped over or fallen down, it
may cause damage or fire.
• Do not place the unit into closed space
of TV for better ventilation; it can reduce the
product lifetime. Keep a space at least 10 cm
at above, left and right of the TV.
• Please place all the signal cords behind of
rear panel.
• Do not overexert or touch the panel when
you convey the product. Do not transfer the
LCD TV up or down display direction.
• Do not transport it with the power cord
or the connection cable connected. If you
move this product with the power cord or the
connection cable connected, the damaged
power cord, connection cable or connection
terminal may cause the fire, the electric shock
or breakdown.
• 2 persons or more shall transport the
device, which is heavier than 18 kg. If you drop
or tip over the device, it can be damaged.
• The temperature of the product’s body
becomes a little higher after a long period use.
This phenomenon indicates that heat exchange
in normal working mode, thus please do not
let children or anyone who is sensitive of
temperature to touch.
All images provided herein are schematic
drawings and may differ from of real objects.
5
Connection
Connection
Outdoor Antenna Connection
Use 75Ω coaxial cable plug or 300-75Ω
impedance converter to plug in antenna input
terminal on the rear of the cabinet.
Other connections
• Connect the audio sources (Including
DVD, VCDR, CAMCORDER and PC) to the
proper Audio input jacks ‘L’ and ‘R’.
• Connect the video source to the
Composite video jack by RCA cable.
• If the video source has a SCART output
jack, you can connect the signal to the monitor
by the SCART cable (not included).
• Component input Y/Pb/Pr is intended
to receive component video signal from the
external device.
• Connect the power cord to the DC
adaptor, then connect the adapter to the DC
power jack of this unit.
• When using the LCD as a computer
screen, connect the PC to the VGA jack from
the monitor by the relevant cable (not included).
• This unit has PC audio in jack. Connect
this jack to PC main unit with related audio
cable in PC mode and adjust the volume to
what you want.
• If the video source has a HDMI output
jack, you can connect the signal to the monitor
by the HDMI cable (not included).
• Connect your headphones or earphones
(not included) to the headphone socket of
this unit. When earphones are connected, the
sound output through the built-in speakers of
this unit is mute.
• Coaxial output is intended for transmitting
multi-channel sound to an external decoder
(e.g. in 5.1-CH format). RCA cable should be
used for connection.
75 Ohm co-axis cable
TVRF antenna jack
Antenna cable connector
6
Operation
Control elements
Front panel
1
2
1. IR sensor
2. Power indicator
1. Disc slot
2. PLAY/PAUSE button
3. EJECT button
4. POWER button
5. TV/AV button
6. CH+/CH- buttons
7. VOL+/VOL- buttons
8. MENU button
9. DC adapter input
10. USB port
11. HDMI input
12. VGA input
13. PC audio input
14. SCART connector
15. Headphone jack
16. Coaxial output
17. RF antenna jack
18. Stereo audio input (white=left;
red=right)
19. Composite video input
20. Component video input
(YPbPr)
Back panel
2
1
3
4
5
6
7
8
9 10 11 12 13 14 15 16
17
18
19
20
7
Operation
Remote controller (RC)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
1. POWER button
2. Number buttons
3. ASPECT button
4. VOL+/VOL- buttons
5. DISPLAY button
6. ENTER button/cursor buttons (LEFT/RIGHT/
UP/DOWN)
7. LCD MENU button
8. P.MODE button
9. INPUT button
10. HOLD/ button
11. TEXT/
button
12. /INDEX button
13. /SIZE button
14. button
15. button
16. TITLE button
17. D.MENU button
18. PROGRAM/Red button
19. INTRO/Green button
20. AUTO/ button
21. MUTE button
22. button
23. NICAM button
24. CH+/CH- buttons
25. DVD SETUP button
26. SMODE button
27. SLEEP button
28. PGUP/SLOW button
29. PGDW/STEP button
30. SUBPAGE/ZOOM button
31. REVEAL/AUDIO button
32. D.SUB button
33. ANGLE button
34. GOTO button
35. D.DISP button
36. A-B/Blue button
37. REPEAT/Yellow button
Changing the battery
1. Remove the battery compartment cover
on the back of the RC.
2. Insert 2 x AAA batteries batteries into
the battery compartment making sure that the
correct polarity is observed.
3. Install the cover back.
• The RC should be pointed at remote
sensor within 8 meters and within 30 degrees
at the left or the right side.
• Take the battery out of the RC if it is not
used for a long time. Do not mix new and used
batteries or different types of batteries. Weak
batteries can leak and severely damage the RC.
• Do not expose the RC to shock, liquids,
and do not place it in an area with high
humidity.
8 9
Operation Operation
General operations
• Press POWER button on the unit or on the
RC to switch on the power, the indication light
will be in green color. Press POWER button
again to switch off the power, and the light will
be in red color.
• The picture setup, sound setup, previous
channel can be memorized before you switch
off the unit. The unit will restart under the
previous state when you switch on it again.
• Press VOL- button repeatedly to decrease
the volume; press VOL+ button repeatedly to
increase the volume from 0 to 100.
• Press SLEEP button repeatedly to set the
sleep time (from 0 to 240 min).
• Select the TV function mode. Channel
‘1’ will appear on the left bottom corner
after channel searching is completed. Press
CH-/CH+ buttons to select previous or next
channels; or press number buttons to enter a
channel number directly; or press [-/--] button
until the screen displays ‘-’ or ‘--’ or ‘---’, then
use number buttons to enter a channel number
from 1 to 199.
• Press button on the RC to select
from the present channel and the previously
displayed channel.
• Press NICAM button in TV mode
repeatedly to switch between different Nicam
sound modes (can be unavailable for some
channels).
• Press P.MODE button repeatedly to cycle
through the available video picture modes from
the following 4 types: Dynamic => Standard =>
Mild => User.
• Press S.MODE button repeatedly to cycle
through the available sound modes from the
following 5 types: Movie => Sports => User =>
Standard => Music.
• Press MUTE button to cut off sound, press
this button again or adjust volume to resume
sound.
• Press DISPLAY button to display the
preset TV channel play information.
• Press ASPECT button repeatedly to select
a screen display size from the available list:
16:9/ZOOM1/ZOOM2/Auto/4:3/Just Scan.
Available aspects may differ for different
signal sources.
Signal sources
Press INPUT button on the RC or TV/AV
button on the unit, then press UP/DOWN
cursor buttons to cycle through the available
source list as follows: TV - AV - SCART -
YPBPR - HDMI - PC - Media - DVD. Press
ENTER button to confirm.
TELETEXT operations (option)
• Press INPUT button to select the TV
mode. Then press CH-/CH+ buttons to select
TV channel in order to pick up the picture
signal of TELETEXT.
• Press PGUP/PGDW buttons to select the
previous page or the next page; use number
buttons and [-/--] button to enter into a page.
• Teletext button functions are as follows:
TEXT: Press TEXT button to enter into
TEXT mode. Press this button again to return
to the channel you are watching.
PGDW: Press this button to view the next
teletext page’s program.
PGUP: Press this button to view the previous
teletext page’s program.
HOLD: Press this button to stop the move to
the next page, and the hold symbol will appear
in the top left hand corner of the screen. Press
this button again to cancel operation.
INDEX: Press this button to go to the index
page.
SIZE: Press this button to enlarge the text
shown on the teletext screen, and one half of
page could be shown. Press this button again
to view the second half of this page. Press this
button third time to normal size text page view.
REVEAL: Press this button to reveal the
cancelled information. Press this button again
to cancel the information.
SUBPAGE: Press this button to select sub
page, and the sub-page symbol will appear in
the left top hand corner of the screen. Enter the
8 9
Operation Operation
number of sub page and use numeric buttons
in the format 0001 for sub page 1. The teletext
will search for the sub page.
Red/Green/Yellow/Blue buttons: Press
these 4 color buttons to access directly to
corresponding color page displayed at the
lower parts of teletext screen.
PC screen
Select the PC input (TV into PC) mode. The
unit has a VGA jack for a normal computer.
Connect the monitor with a PC by this jack and
the unit can be used as the monitor for the PC.
OSD operation
1. Press LCD MENU button to enter the
setting menu displayed on the screen.
2. Press LEFT/RIGHT cursor buttons on the
RC or VOL+/- buttons on the panel to select
setting page.
3. Press DOWN cursor button or ENTER
button on the RC or CH+ button on the panel
to go to the parameter list.
4. Press UP/DOWN cursor buttons on the
RC or CH+/- buttons on the panel to select a
parameter to adjust.
5. Press cursor buttons on the RC or VOL+/-
or CH+/- buttons on the panel to adjust the
selected parameter.
6. Press LCD MENU button to return to the
previous menu page.
Some menu items may be in grey color,
in this case they are not adjustable. Pictures
of OSD menu are for reference only; they may
differ from the real screens.
Channel setting (only for TV source)
CHANNEL
Auto tuning
ATV Manual tuning
Programme edit
Move Menu OK Exit
Auto tuning: press LEFT/RIGHT buttons
to start automatic search of available channels.
To stop the process press LCD MENU button.
ATV Manual tuning: Press ENTER button
to enter into manual tuning menu:
Current Channel: select channel number.
Colour System: select corresponding colour
system.
Sound System: select corresponding sound
system.
Fine-tune: perform fine adjustment of the
current frequency.
AFC: set On/Off automatic frequency
correction.
Search: press LEFT/RIGHT buttons; the
unit will search for next available channel
downward or upward and save it under the
current number.
Program Edit: this item allows you to sort
TV programs according to your preferences.
Enter into program edit menu:
Delete: Select the channel you want to delete.
Press red button to delete the channel.
Rename (only in ATV mode): Highlight the
needed channel. Press green button; then press
UP/DOWN buttons to select a symbol. Press
LEFT/RIGHT buttons to select the next symbol.
Press ENTER button to confirm.
Move: Highlight the needed channel. Press
yellow button; select the position to put the
channel into. Press yellow button to confirm.
Skip: Highlight the needed channel. Press
blue button; now this channel will be skipped
when you select previous/next channels.
10
Operation
Picture setting
PICTURE
Picture mode
Contrast
Brightness
Color
Tint
Sharpness
Color temperature
Noise reduction
Move Menu OK Exit
Picture Mode: Dynamic/Standard/Mild/
User.
Contrast
Brightness
Color
Tint: adjust the tone of color when your
system is in NTSC.
Sharpness
Colour Temperature: Normal/Warm/Cool.
Noise Reduction: Digital noise reduction
effect for reducing the video noise level: Off/
Low/Middle/High.
Sound setting
SOUND
Sound mode
Treble
Bass
Balance
Auto volume
SPDIF mode
Move Menu OK Exit
Sound mode: Movie/Sports/User/
Standard/Music.
Treble: adjust treble frequency.
Bass: adjust bass frequency.
Balance: adjust balance between left and
right speaker.
Auto volume: set the auto volume
correction on/off.
SPDIF mode: select PCM/Auto/Off.
Timer setting
TIME
Sleep timer
Auto sleep
OSD timer
Move Menu OK Exit
Sleep timer: select the period until
automatic switch-off of the unit (0 - 240 min).
Auto sleep: select the period of time after
which the unit will automatically switch off if no
operation is done.
OSD timer: select the period of time after
which the OSD will be hidden.
Option setting
OPTION
OSD language
TT language
Aspect ratio
Blue screen
Key lock
Reset
Software upgrade (USB)
Move Menu OK Exit
OSD Language: select the language of
the OSD menu.
TT Language: select teletext language.
Aspect ratio: 16:9/ZOOM1/ZOOM2/
Auto/4:3/Just Scan. The set of available
aspects can vary depending on the current
signal source.
Blue screen: set on or off blue screen
activation when no signal.
Key lock: select ON to lock all buttons on
the panel. Set OFF to unlock the buttons.
Reset: reset the parameters to initial
factory settings.
• Software upgrade: this option is intended
for using by qualified technicians only.
11
Operation
Screen setting (only for PC mode)
SCREEN
Auto adjust
Horizontal Pos.
Vertical Pos.
Clock
Phase
Move Menu OK Exit
Auto adjust: automatical setting of the
parameters. Also to perform this function you
can press AUTO/ button on the RC.
Horizontal Position: adjust horizontal
position of the image.
Vertical Position: adjust vertical position
of the image.
Clock: adjust the image frequency
manually.
Phase: adjust the phase manually.
USB operation
Insert a USB into the USB jack. Select
Media source and press ENTER button. The
screen will show a USB playback window, in
which you can select Music, Photo, Movie and
Text contents to play by pressing LEFT/RIGHT
cursor buttons and ENTER button.
USB file systems supported: FAT,
FAT32. 2.0 USB version is supported. For
correct and satisfactory operation, licensed
USB devices of famous brands should be
used with this unit. Avoid using USB devices
of unknown brands. Playback of some file
formates cannot be supported.
General operations of file playback
• Press cursor buttons to select Return
option and press ENTER button if you want to
go back to the previous menu.
• In the content menu, press cursor buttons
to select folder, press ENTER button or
TEXT/ button to enter it, then press cursor
buttons to select the file you want to watch
or to listen to. When highlighting the file, the
file information will appear on the right (not
available for text files) and picture will be
previewed in the center (not available for music
and text files). Press ENTER button or TEXT/
button to play the selected file.
• While playback, press INFO button; the
bottom of the screen will show playback menu
in which you can select an operation by LEFT/
RIGHT cursor buttons on perform this opera-
tion by pressing ENTER button.
• While playback, press TEXT/
button
to pause or resume playback. Press HOLD/
button to stop playback.
• When playing photo, movie and music
files, you can press REPEAT button to select
the repeat play mode.
• When playing music files you can press
/ buttons to fast reverse or forward. You can
press
/ buttons to select the desired files
manually in normal condition.
• When playing photo files, you can press
/ buttons to page up or page down the
file. Press LEFT/RIGHT cursor buttons to
rotate the image.
DVD player operation
Turn on and off the DVD function
Turn on the LCD TV and then select DVD
source.
Insert disc
• Insert the disc to the disc slot, the player
will load the disc automatically. After loading
the disc content, it will switch to play mode
automatically.
• Insert disc with reflective data side facing
the front of the unit. When inserting the
disc incorrectly, you may damage the DVD
mechanism. Some slight picture noise and
some sounds can be produced when the disc
is loading, unloading and during playback, this
is normal and can be ignored.
12 13
Operation Operation
• For some discs, after loading the content
of the disc, you need to press TEXT/ button
or select from the disc menu to start.
• To eject the disc from the loader press
AUTO/
button on the RC or EJECT button on
the unit.
• Only standard shape and 12-cm size discs
can be used.
Play the disc
According to the disc content, menu will
display for your selection. When playing the
disc, you may use TEXT/
button on the RC
or PLAY/PAUSE button on the unit to toggle
between Play and Pause mode.
Manufacturer guarantees regular
playback of licensed discs only. Some AVI files
cannot be played due to their parameters and
recording conditions. Video files more than 2 Gb
having AVI extension can be played partially.
Stop
While playback, press HOLD/ button to
stop playback. If you press TEXT/ button,
playback will resume from the stop point.
Press HOLD/ button twice; if afterwards you
press button, playback will start from the
beginning.
For some kinds of discs last memory
function is not available.
Rewind/Fast forward
While playback, press repeatedly /
buttons to fast reverse or forward. With each
pressing, the playback speed will increase as
follows: 2X - 4X - 8X - 16X - 32X - Normal.
While fast playback, press TEXT/ button to
go to normal speed playback.
Previous/next track/chapter/title
While playback press / buttons to
select previous or next track/chapter. Press
number button to select the track under
corresponding number.
Slow playback
Press PGUP/SLOW button repeatedly to
select slow playback speed: 1/2 - 1/4 - 1/8 - 1/16
- Normal. While slow playback, press TEXT/
button to go to normal speed playback.
Zoom
While playback press ZOOM button to zoom
in or out the image as follows: 2x - 3x - 4x - 1/2
- 1/3 - 1/4 - Normal. When zoomed in, you can
press cursor buttons to move the picture.
Repeat
While playback press REPEAT button to
select repeat mode (repeat track/chapter/title
repeat all tracks/chapters/titles, etc.). Available
repeat modes may differ depending on the type
of the disc.
A-B
While playback press A-B button on the
RC to set the beginning of the fragment to
play repeatedly. Press this button again to set
the final point of the fragment. The selected
fragment will be played repeatedly. Press this
button again to cancel repeat playback.
Step
While video playback press PGDW/STEP
button once to make the picture still. Press this
button repeatedly to play the video frame by
frame. Press TEXT/
button to go to normal
speed playback. While step playback, the sound
is cut off.
Display
While playback press D.DISP button on the
RC to show the current playback information
such as Title/Chapter elapsed/remaining etc.
Available data may differ depending on the
type of the disc.
Program
• While playback press PROGRAM button
to call programming menu. Press cursor
buttons on the RC to select a position, then
press number buttons to set the number
12 13
Operation Operation
of track/title (depending on the disc type).
After all the positions are filled, press press
TEXT/
button or select PLAY item and
press ENTER button to start playback of the
programmed track/chapter sequence. To
cancel programming, select EXIT item and
press ENTER button or just press PROGRAM
button. The programming menu will hide.
• If you press HOLD/
button twice or turn
off the unit, the program will be deleted.
Subtitle
Press D.SUB button repeatedly to toggle
between different subtitle languages.
Selectable subtitle languages depend
on the availability in the DVD contents.
Angle
Press ANGLE button repeatedly to toggle
between different view angles. After selecting
an angle, press TEXT/
button to confirm.
Selectable view angles depend on the
availability in the DVD contents.
MP3 operation
• After you insert an MP3 disc, the player
will initialize the disc and the directory (folder)
will be shown in an MP3 Menu on screen.
• Press LEFT/RIGHT cursor button twice
to select and highlight the PLAY MODE. Then
press UP/DOWN cursor button each way to
select play mode options (repeat, shuffle, etc.)
Then press LEFT/RIGHT cursor button twice
and then DOWN button to select and highlight
an MP3 file (song). Press TEXT/ button
to highlight your list of songs. Press DOWN
button to select and highlight.
• Press TEXT/ button to play the MP3 file.
Press / buttons during playback to skip
the tracks. If you need to return to the main
directory (folder), press HOLD/ button.
The left column of the MP3 Menu is a
list showing the name of the folder. The right
column is a list showing the name of the song
and the sub-folder. During MP3 playback, you
cannot access to PLAY MODE folder or songs.
Intro
Press INTRO button to enable intro mode;
the first 10 seconds of each MP3 track will be
played. Press this button again to cancel.
Title
Press TITLE button to display the disc title
menu. Press cursor or number buttons to
select your favorite title, then press ENTER
button to confirm. It will play from the first
chapter of selected title.
For some kinds of discs this function
can be unavailable.
Audio
Press REVEAL/AUDIO button to toggle
between different audio channels (left/right) or
audio languages.
Selectable audio languages or channels
depend on the availability in the disc contents.
Goto function
You could choose from your favorite place
to play the disc by using GOTO button. Press
GOTO button during playback. By pressing
cursor buttons move the cursor, and input the
numbers to select the title, chapter and time (or
track) you want. Press TEXT/ button to play
from the point you choose.
For different discs, GOTO button may
be have different functions.
Disc menu operation
• Press D.MENU button to display disc
menu or return to the root menu when playing
the disc. Press TEXT/ button to start from
highlighted content.
• Press HOLD/ button once to stop, press
TEXT/ button to resume from where you
stopped; Press HOLD/ button twice to stop,
press TEXT/ button to start from beginning.
For different discs D.MENU button may
have different menu display information.
14
Operation
System setup
1. Press DVD SETUP button to enter the
setup menu. In Setup menu, press DVD
SETUP button again to quit the setup page.
2. Use LEFT/RIGHT cursor buttons to
choose a setup page: General setup, Audio
setup, Dolby Digital setup, Preference page.
3. Press DOWN cursor button to enter the
setup page selected.
4. Use UP/DOWN cursor buttons to select
the option you want to adjust.
5. Press RIGHT cursor button to enter the
adjustment list. Use UP/DOWN cursor buttons
to select the adjustment and press ENTER
button to confirm and LEFT cursor button to
return to options list.
6. To return to setup page list press LEFT
cursor button when in the option list.
Pictures of OSD menu are for reference
only; they may differ from the real screens.
General setup
General setup page
TV display
OSD lang
Screen saver
Last memory
TV Display: select the TV picture fromat.
4:3 PS: The wide-screen image is shown on
the full screen, but some part is cut off.
4:3 LB: The wide-screen image is shown
and black stripes appear on the top and bottom
of screen.
16:9: Normal picture format.
OSD Lang: select on-screen display
language.
Screen Saver: Set screen saver on/off.
Last Memory: When this function is on,
the unit can memorize the time elapsed from
the last time you played the disc. Then at the
next playing, it will resume playing from the
memorized time.
Audio setup
Audio setup page
Speaker setup
Speaker setup: Downmix: select a mode
of downmix (LT/RT or Stereo).
Dolby Digital setup
Dolby digital setup
Dual mono
Dynamic
Dual Mono
Stereo: stereo output signal,
L-Mono: left output signal,
R-Mono: right output signal,
Mix-Mono: left and right output average
signal.
Dynamic: If watching large dynamic scope
movie program at night, selecting this mode
you can reduce the volume to a very low level,
at the same time, to keep the fine details sound.
15
General information
Preference setup
Preference page
TV Type
Audio
Subtitle
Disc menu
Parental
Password
Default
TV type: Select PAL/Multi/NTSC.
Audio, Subtitle, Disc Menu: Set the
language of the audio, subtitles or disc menu.
Parental: The control level is for parental to
control playing content and protect your children
from violence and erotic. The disc, the level of
which is higher than the setting level cannot be
played.
Password: Change the password. The
initial factory password is 123456. You can set
your own password.
Default: Restore the initial factory settings.
Troubleshooting
Below is a table describing simple measures that can help you eliminate most problems likely
to emerge when this unit is in use. If below measures do not help, turn to a service center or to the
nearest dealer.
Symptom Cause Solution
No picture, no
sound, and no
indicator light
The power cord is not plugged in.
Contrast, brightness, sharpness, color
and volume are all in the minimum
value or TV is in mute mode.
Plug the power cord in.
Alter the value of contrast,
brightness, sharpness, color and
volume.
Picture and
sound with
abnormity
Contrast and color are set improperly.
Color system is set improperly.
Sound system is set improperly.
Set the value of Contrast and color
properly.
Set the sound system properly.
Picture is spotted
or with snow
Signal source is low-grade or the
signal is in a lower quality.
Use the qualified signal cord.
Blue background No video signal or the signal cord is
improperly/not connected.
Connect the signal cord properly.
16
General information
Picture is not in
the middle of the
screen
Picture is not well adjusted. Adjust H/V position manually to
adjust it.
No sound No audio signal or the signal cord is
im-properly/not connected.
Connect the audio signal cord
properly.
Set the sound system properly.
Disc cannot be
loaded
The unit already contains a disc. Remove the disc in the player then
put a new one.
Disc cannot be
read
The disc is inserted with a wring
side.
Insert the compact disc with the right
side.
Compact disc is extremely dirty or
defective.
Clean the disc or try to play a new
one.
The RC does not
work
Batteries are improperly installed or
exhausted.
Make sure the positive and the
negative polarities are correct.
Reattach the battery lid.
Replace the batteries.
Causes of interference
Your TV receiver has the most up-to-date
devices to eliminate interference. Local
radiation, however, can create disturbances,
which visibly affect your picture. Proper
installations, a good aerial are your best
safeguards against these disturbances.
• RF INTERFERENCE: Moving ripples
across the screen are caused by nearby
transmitting or receiving short-wave radio
equipment.
• DIATHERMY: Herringbone pattern
and partial picture loss can result from the
operation of diathermy equipment from a
nearby doctor’s surgery or hospital.
• SNOW: Weak TV signals from long
distant stations result in an instead picture
and give the effect of falling snow. An antenna
adjustment or antenna amplifier may be
needed.
• GHOST: Multiple image, caused by
TV signals reflected back from surrounding
buildings, hills, aircraft, etc. is minimized by
correct aerial positioning.
• CAR IGNITION: Nearby cars and electrical
motors can cause small streaks across the
picture or make the picture roll.
Accessories
1. LED TV 1 pc
2. Remote controller 1 pc
3. Battery 2 pcs
4. Stand 1 pc
5. Power adaptor 1 pc
6. Power cord 1 pc
7. AV RCA cable 1 pc
8. Consumer information 1 pc
9. Warranty card 1 pc
10. Instruction manual 1 pc
17
General information
Specifications
S
ize (diagonal) 23.6” (60 cm)
Response time 5 ms
Resolution 1920 x 1080
Aspect ratio 16:9
Color system PAL, SECAM
Sound system B/G, DK, I
NICAM Stereo 2 x 3 W
Storage support CD-R/RW, DVD-R/RW, DVD+R/+RW, USB
Component video input +
AV RCA input +
USB port +
VGA input +
HDMI input +
PC audio input +
Coaxial output +
SCART connector +
Headphone output +
Russian and English OSD +
Progressive scan +
Digital comb filter +
Sleep timer +
Quantity of channels 199
Teletext pages 1000
USB movie, photo and audio support +
Power supply (DC adapter) ~110-240 V, 50/60 Hz (12 V; 3.3 A)
Power consumption 40 W
Electric shock protection class II
Unit dimensions (with stand) 573 x 408 x 155 mm
Net/Gross weight 5.6 kg/6.6 kg
The LCD panel is a high technology product with many thin film transistors that can
give you a fine picture details. Occasionally, a few non-active pixels may appear on the screen
as a fixed point of blue, green, red, black or white, please note that this does not affect the
performance of your LCD TV.
Warning: Specifications may be subject to change without notice for improvement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

Hyundai H-LEDVD19V10 User manual

Category
LCD TVs
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI