Please visit us at http://solutions.brother.com where you can get product support
and answers to frequently asked questions (FAQs).
KNOWING YOUR
SEWING MACHINE
SEWING BASICS
VARIOUS STITCHES
APPENDIX
INTRODUCTION
Thank you for purchasing this sewing machine. Before using this machine, carefully read the "IMPORTANT
SAFETY INSTRUCTIONS", and then study this manual for the correct operation of the various functions. In
addition, after you have finished reading this manual, store it where it can quickly be accessed for future
reference.
Please read these safety instructions before attempting to use the machine.
DANGER - To reduce the risk of electric shock:
1Always unplug the machine from the electrical outlet immediately after using, when cleaning,
when making any user servicing adjustments mentioned in this manual, or if you are leaving the
machine unattended.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons.
2Always unplug the machine from the electrical outlet when making any adjustments mentioned
in the instruction manual:
•
•
•
To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp
the plug and pull it out of the electrical outlet. Do not pull on the cord.
Plug the machine directly into the electrical outlet. Do not use an extension cord.
Always unplug your machine if the power is cut.
3 Never operate this machine if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or water is spilled on the unit. Return the machine to the nearest
authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
While the machine is stored or in use if you notice anything unusual, such as an odor, heat,
discoloration or deformation, stop using the machine immediately and unplug the power cord.
When transporting the sewing machine, be sure to carry it by its handle. Lifting the sewing
machine by any other part may damage the machine or result in the machine falling, which could
cause injuries.
When lifting the sewing machine, be careful not to make any sudden or careless movements,
otherwise you may injure your back or knees.
IMPORTANT SAFETY
INSTRUCTIONS
1
4 Always keep your work area clear:
• Never operate the machine with any air openings blocked. Keep ventilation openings of the
sewing machine and foot control free from the build up of lint, dust, and loose cloth.
• Do not store objects on the foot controller.
• Do not use extension cords. Plug the machine directly into the electrical outlet.
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
• Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine,
power cord or garment being sewn may ignite, resulting in fire or an electric shock.
• Do not place this sewing machine on an unstable surface, such as an unsteady or slanted table,
otherwise the sewing machine may fall, resulting in injuries.
5 Special care is required when sewing:
• Always pay close attention to the needle. Do not use bent or damaged needles.
• Keep fingers away from all moving parts. Special care is required around the machine needle.
• Switch the sewing machine to the symbol “O” position to turn it off when making any adjustments
in the needle area.
• Do not use a damaged or incorrect needle plate, as it could cause the needle to break.
• Do not push or pull the fabric when sewing, and follow careful instruction when freehand stitching
so that you do not deflect the needle and cause it to break.
6 This machine is not a toy:
• Your close attention is necessary when the machine is used by or near children.
• The plastic bag that this sewing machine was supplied in should be kept out of the reach of
children or disposed of. Never allow children to play with the bag due to the danger of
suffocation.
• Do not use outdoors.
7 For a longer service life:
• When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store
the machine near a space heater, iron, halogen lamp, or other hot objects.
• Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders
can damage the case and machine, and should never be used.
• Always consult the operation manual when replacing or installing any assemblies, the presser feet,
needle, or other parts to assure correct installation.
2
8 For repair or adjustment:
• If the Light unit (light-emitting diode) is damaged, it must be replaced by authorized dealer.
• In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table
in the back of the operation manual to inspect and adjust the machine yourself. If the problem
persists, please consult your local authorized Brother dealer.
Use this machine only for its intended use as described in this manual.
Use accessories recommended by the manufacturer as contained in this manual.
The contents of this manual and specifications of this product are subject to change without notice.
For additional product information, visit our web site at www.brother.com
SAVE THESE INSTRUCTIONS
This machine is intended for household use.
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
FOR USERS IN THE UK, EIRE,
MALTA AND CYPRUS ONLY
IMPORTANT
• In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the
mark, rating as marked on plug.
• Always replace the fuse cover. Never use plugs with the fuse cover omitted.
• If the available electrical outlet is not suitable for the plug supplied with this equipment, you
should contact your authorized dealer to obtain the correct lead.
3
CONTENTS
1. KNOWING YOUR SEWING MACHINE ..........................................................5
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS ....................................................5
The main parts ................................................................................................................................................. 5
Needle and presser foot section ...................................................................................................................... 6
Operation buttons ............................................................................................................................................. 6
Operation panel ................................................................................................................................................ 7
Flat bed attachment ......................................................................................................................................... 7
ACCESSORIES .....................................................................................................................8
Optional accessories ........................................................................................................................................ 8
USING YOUR SEWING MACHINE .....................................................................................9
Power supply precautions ................................................................................................................................ 9
Turning on the machine ................................................................................................................................... 9
Foot controller ................................................................................................................................................ 10
Sewing speed controller (for models equipped with the sewing speed controller) ......................................... 10
Changing the needle stop position ................................................................................................................. 10
Changing the initial needle position ............................................................................................................... 11
Cancelling the operation beep (for models equipped with the operation beep) ............................................. 11
THREADING THE MACHINE ............................................................................................12
Winding the bobbin ........................................................................................................................................ 12
Lower threading ............................................................................................................................................. 15
Upper threading ............................................................................................................................................. 17
Drawing up the lower thread .......................................................................................................................... 20
REPLACING THE NEEDLE .................................................................................................21
Needle precautions ........................................................................................................................................ 21
Needle types and their uses ........................................................................................................................... 21
Checking the needle ...................................................................................................................................... 22
Replacing the needle ..................................................................................................................................... 22
Sewing with a twin needle .............................................................................................................................. 24
REPLACING THE PRESSER FOOT ......................................................................................25
Replacing the presser foot ............................................................................................................................. 25
Removing the presser foot holder .................................................................................................................. 26
2. SEWING BASICS ...........................................................................................27
SEWING ............................................................................................................................27
General sewing procedure ............................................................................................................................. 27
Selecting a stitch ............................................................................................................................................ 28
Starting to sew ............................................................................................................................................... 29
Adjusting thread tension ................................................................................................................................. 31
USEFUL SEWING TIPS ......................................................................................................32
Trial sewing .................................................................................................................................................... 32
Changing the sewing direction ....................................................................................................................... 32
Sewing curves ................................................................................................................................................ 32
Sewing thick fabrics ....................................................................................................................................... 32
Sewing hook-and-loop fastener ..................................................................................................................... 33
Sewing thin fabrics ......................................................................................................................................... 34
Sewing stretch fabrics .................................................................................................................................... 34
Using a free-arm style .................................................................................................................................... 34
—————————————————————————————————————————————————————————
—
4
3. VARIOUS STITCHES .....................................................................................35
STITCH SETTINGS .............................................................................................................35
Utility stitches ................................................................................................................................................. 35
Character stitches (for models equipped with character stitches) .................................................................. 41
OVERCASTING STITCHES ................................................................................................42
BASIC STITCHING ............................................................................................................43
Basic stitching ................................................................................................................................................ 43
BLIND HEM STITCHING ..................................................................................................44
BUTTONHOLE SEWING ...................................................................................................46
Button sewing ................................................................................................................................................. 49
ZIPPER INSERTION ...........................................................................................................51
SEWING STRETCH FABRICS AND ELASTIC TAPE ............................................................52
Stretch stitching .............................................................................................................................................. 52
Elastic attaching ............................................................................................................................................. 52
APPLIQUÉ, PATCHWORK AND QUILT STITCHING ........................................................53
Appliqués ....................................................................................................................................................... 53
Patchwork (crazy quilt) stitching ..................................................................................................................... 54
Piecing ........................................................................................................................................................... 54
Quilting ........................................................................................................................................................... 55
Free-motion quilting ....................................................................................................................................... 56
REINFORCEMENT STITCHING .........................................................................................57
Triple stretch stitching .................................................................................................................................... 57
Bar tack stitching ............................................................................................................................................ 57
DECORATIVE STITCHING ................................................................................................59
Fagoting ......................................................................................................................................................... 60
Scallop stitching ............................................................................................................................................. 61
Smocking ....................................................................................................................................................... 61
Shell tuck stitching ......................................................................................................................................... 62
Joining ............................................................................................................................................................ 62
Heirloom stitching ........................................................................................................................................... 63
SEWING CHARACTERS (for models equipped with character stitches) ............................64
Selecting characters ....................................................................................................................................... 64
Checking characters ...................................................................................................................................... 66
Deleting characters ........................................................................................................................................ 66
Sewing the character stitches ........................................................................................................................ 67
ADJUSTING STITCHES (for models equipped with character stitches) .............................68
4. APPENDIX .....................................................................................................70
MAINTENANCE ................................................................................................................70
Cleaning the machine surface ........................................................................................................................ 70
Cleaning the bobbin case ............................................................................................................................... 70
TROUBLESHOOTING .......................................................................................................72
ERROR MESSAGES ............................................................................................................75
Operation beep (for models equipped with the operation beep) .................................................................... 75
INDEX ...............................................................................................................................76
5
1
1 KNOWING YOUR SEWING MACHINE
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
The main parts
a Bobbin winder (page 12)
This winds the thread onto the bobbin for use as the
lower thread.
b Spool pin (pages 12 and 17)
This holds the spool of thread.
c Hole for extra spool pin (page 24)
This holds a second spool of thread for sewing with two
needles. Not for lubrication.
d Upper tension-control dial (page 31)
This controls the tension of the upper thread.
e Thread guide (pages 12 and 17)
This is used when winding the thread onto the bobbin
and then threading the machine.
f Thread take-up lever (page 18)
g Thread cutter (page 30)
Pass the threads through the thread cutter to cut them.
h Flat bed attachment with accessory compartment
(pages 7 and 34)
i Operation buttons (page 6)
The operation buttons differ depending on the sewing
machine model.
j Operation panel (page 7)
This is used to select the stitch and specify the various
settings.
k Handwheel
Used to manually raise and lower the needle.
l Main power and sewing light switch (page 9)
You can turn the main power and sewing light switch
on and off.
m Jack/socket connector (page 9)
Insert the plug on the power supply cord into the jack/
socket connector.
n Foot controller jack/socket (page 10)
Plug in the foot controller plug.
o Feed dog position lever (pages 49 and 56)
Use the feed dog position lever to lower the feed dogs.
p Presser foot lever (page 17)
Used to raise and lower the presser foot.
q Foot controller (page 10)
You can use this to control the sewing speed, and to
start and stop sewing.
r Handle
Carry the sewing machine by its handle when
transporting the machine.
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
—
6
Needle and presser foot section
a Buttonhole lever
Lower the buttonhole lever when sewing buttonholes
and bar tacks.
b Needle threader (for models equipped with the needle
threader) (page 18)
c Presser foot holder
The presser foot is installed onto the presser foot holder.
d Presser foot holder screw
Use the presser foot holder screw to hold the presser
foot holder in place.
e Presser foot
The presser foot applies pressure consistently on the
fabric as the sewing takes place. Attach the appropriate
presser foot for the selected stitching.
f Feed dogs
The feed dogs feed the fabric in the sewing direction.
g Quick-set bobbin (for models equipped with the quick-
set bobbin)
You can start sewing without pulling up the bobbin thread.
h Bobbin cover
Open the bobbin cover to set the bobbin.
i Needle plate
The needle plate is marked with guides for sewing
straight seams.
j Needle bar thread guide
Pass the upper thread through the needle bar thread guide.
k Needle clamp screw
Use the needle clamp screw to hold the needle in place.
Operation buttons
The operation buttons help you to easily perform various basic sewing machine operations.
The operation buttons differ depending on the sewing machine model.
a Presser foot lever
Raise and lower the presser foot lever to raise and lower
the presser foot.
b Reverse/reinforcement stitch button
Press the reverse/reinforcement stitch button to sew
reverse stitches. Reverse stitches are sewn by keeping
the button pressed down to sew in the opposite
direction. For details, refer to “Sewing reinforcement
stitches” (page 30).
■ Buttons provided on some models
c Start/stop button (for models equipped with the
start/stop button)
Press the start/stop button to start or stop sewing. The
machine sews at a slow speed at the beginning of
sewing while the button is depressed. When sewing is
stopped, the needle is lowered in the fabric. For details,
refer to “Starting to sew” (page 29).
d Needle position button (for models equipped with
the needle position button)
Press the needle position button to raise or lower the
needle. Pressing the button twice sews one stitch.
e Sewing speed controller (for models equipped with the
sewing speed controller)
Slide the sewing speed controller to adjust the sewing
speed.
7
1
Operation panel
The operation panel, located on the front of the sewing machine, allows you to select a stitch and specify how
the stitch will be sewn.
a LCD (liquid crystal display)
The number of the selected stitch (
1), the presser foot
to be used (
2), the stitch length (mm) (3), and the
stitch width (mm) (
4) are displayed here.
b Stitch selection keys
Press the stitch selection keys, and then select the
number for the stitch that you wish to use. For details,
refer to “Selecting a stitch” (page 28).
c Stitch length adjustment key
Press this key to adjust the stitch length.
(For models equipped with the character stitch key)
Press this key to check the combined characters. For
details, refer to “Checking characters” (page 66).
d Stitch width adjustment key
Press this key to adjust the stitch width.
(For models equipped with the character stitch key)
Press this key to add or delete characters. For details,
refer to “SEWING CHARACTERS (for models equipped
with character stitches)” (page 64).
■ Keys and indicators provided on some models
e Utility stitch key
Press this key to sew utility stitches. For details, refer to
“Selecting a stitch” (page 28) .
f Utility stitch indicator
This indicator lights up when the utility stitch key is
pressed.
g Character stitch key
Press this key to sew character stitches. For details, refer
to “SEWING CHARACTERS (for models equipped with
character stitches)” (page 64).
h Character stitch indicator
This indicator lights up when the character stitch key is
pressed.
Flat bed attachment
The accessories are stored in a compartment inside the flat bed attachment.
a
Slide the flat bed attachment to the left to open it.
a Flat bed attachment
b Storage compartment
Note
● Put the accessories in the bag, and then store the bag inside the compartment. If the accessories are not
in a bag, they may fall out, and be lost or damaged.
ABC
3
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
—
8
ACCESSORIES
The following accessories are stored in the flat bed attachment. We have designed these accessories to help you
be able to carry out most sewing tasks.
Note
(For U.S.A. only)
● Foot controller: Model T
This foot controller can be used on the following machine models
:
HS-3000, SQ-9000, SQ9050,
XR9500PRW.
● The screw of the presser foot holder is available through your authorized dealer. (Part code: 132730-122)
Optional accessories
1. 2. 3. 4. 5. 6. 7. 8.
9. 10.
75/11 1 needle
90/14 1 needle
100/16 1 needle
11. 12.
90/14 1 needle
13. 14. 15. 16.
No. Part Name
Part Code
No. Part Name
Part Code
U.S.A. / Canada
Others
U.S.A. / Canada
Others
1 Buttonhole foot “A” XC2691-033 9 Bobbin (4) SA156
XA5539-151
2 Overcasting foot “G” XC3098-031 10 Needle set XC8834-021
3 Monogramming foot “N” XD0810-031 11 Twin needle 131096-121
4 Zipper foot “I” X59370-021 12
Ball point needle
(gold colored)
XD0360-021
5 Zigzag foot “J” (on machine) XC3021-031 13 Cleaning brush X59476-021
6 Blind stitch foot “R” XC4051-031 14 Screwdriver XC8349-021
7 Button fitting foot “M” XE2137-001 15 Extra spool pin 130920-021
8 Seam ripper X54243-051 16 Foot controller
XD0501-021 (EU area)
XC8816-021 (Other areas)
1. 2. 3. 4. 5.
No. Part Name
Part Code
No. Part Name
Part Code
U.S.A. / Canada
Others
U.S.A. / Canada
Others
1 Walking Foot SA140 F033N 4 Quilting guide SA132 F016N
2 Quilting Foot SA129 F005N 5 Eyelet punch XZ5051-001
3
1/4-Inch Quilting
Foot
SA125 F001N
9
1
USING YOUR SEWING MACHINE
Power supply precautions
Be sure to observe the following precautions concerning the power supply.
Turning on the machine
a
Insert the plug into a wall outlet.
a Main power switch
b Jack/socket connector
b
Set the main power switch to “I”.
X The sewing lamp comes on when the
machine is turned on.
c
To turn off the machine, set the main power
switch to “
{
”.
X The sewing lamp goes off when the
machine is turned off.
Note
● If a power outage occurs while the sewing
machine is being operated, turn off the
sewing machine and unplug the power
supply cord. When restarting the sewing
machine, follow the necessary procedure to
correctly operate the machine.
(For U.S.A. only)
● This appliance has a polarized plug (one
blade wider than the other). To reduce the
risk of electric shock, this plug is intended
to fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet,
reverse the plug.
If it still does not fit, contact a qualified
electrician to install the proper outlet. Do
not modify the plug in any way.
● Use only regular household electricity for the power source. Using other power sources may result in
fire, electric shock, or damage to the machine.
● Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power
supply jack on the machine.
● Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
● Turn off the main power and remove the plug in the following circumstances:
• When you are away from the machine
• After using the machine
• When the power fails during use
• When the machine does not operate correctly due to a bad connection or a disconnection
• During electrical storms
● Use only the power cord included with this machine.
● Do not use extension cords or multi-plug adapters with many other appliances plugged in to them. Fire
or electric shock may result.
● Do not touch the plug with wet hands. Electric shock may result.
●
When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from
the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.
● Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled.
Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the
cord and cause fire or electric shock. If the cord or plug is damaged, take the machine to your
authorized dealer for repairs before continuing use.
●
Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a fire may result.
WARNING
CAUTION
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
—
10
Foot controller
Insert the foot controller plug into its jack/socket on
the rear side of the sewing machine.
a Foot controller jack/socket
When you press the foot controller down lightly, the
machine will run at a low speed. When you press
harder, the machine’s speed will increase. When you
take your foot off the foot controller, the machine
will stop.
You should make sure that nothing is placed on the
foot controller when the machine is not in use.
Note
● When the foot controller is plugged in, the
start/stop button cannot be used to start
sewing (only for models equipped with the
start/stop button).
Sewing speed controller
(for models equipped with
the sewing speed controller)
a
Slide the sewing speed controller to the left or
right to select the desired sewing speed.
Slide the sewing speed controller to the left to
sew at a slower speed, or slide the speed
controller to the right to sew at a faster speed.
a Sewing speed controller
• The speed set using the sewing speed
controller is the foot controller’s maximum
sewing speed.
Changing the needle stop position
Normally, the sewing machine is set to leave the needle in
the fabric when sewing is stopped. Instead, the machine can
be set to leave the needle raised when sewing is stopped.
a
Turn off the sewing machine.
b
Hold down the “–” side of (stitch selection
key) on the left and turn on the sewing machine.
After turning on the sewing machine, release
the “–” side of (stitch selection key).
X The needle stop position changes to the
raised position.
Memo
● Perform the same operation to change the
needle stop position to the lowered
position.
● When connecting the foot controller, be sure
to turn off the sewing machine in order to
prevent the machine from accidentally being
started.
● Do not allow pieces of cloth and dust to build
up on the foot controller. Doing so could
cause a fire or an electric shock.
CAUTION
Slower
Faster
CAUTION
11
1
Changing the initial needle
position
Normally, the straight stitch (left needle position) is
automatically selected when the sewing machine is
turned on. The machine can be set so that the
straight stitch (center needle position) is
automatically selected when it is turned on.
a
Turn off the sewing machine.
b
Hold down the “+” side of (stitch selection
key) on the left and turn on the sewing
machine.
After turning on the sewing machine, release
the “+” side of (stitch selection key).
X The initial needle position changes to
the center needle position.
Memo
● The specified initial needle position is
maintained even after the machine is turned
off.
● Perform the same operation to change the
initial needle position to the left needle
position.
Cancelling the operation beep
(for models equipped with the
operation beep)
When the sewing machine is purchased, it is set to
beep each time a key is pressed. This setting can be
changed so that the machine does not beep.
a
Turn off the sewing machine.
b
Hold down the “–” side of (stitch width
adjustment key) and turn on the sewing
machine.
After turning on the sewing machine, release
the “-” side of (stitch width adjustment
key).
X The machine is now set so that it will
not beep.
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
—
12
THREADING THE MACHINE
Winding the bobbin
This section describes how to wind the thread onto the bobbin.
• For details on the fast bobbin winding, see page 14.
a Pre-tension disk
b Bobbin winder shaft
c Bobbin
a
Pull up the spool pin as far as possible, and
then put a spool of thread on this pin.
b
Pass the thread around the pre-tension disk.
c
Pass the end of the thread through the hole on
the bobbin from the inside of the bobbin.
d
Put the bobbin onto the bobbin winder shaft
and slide the bobbin winder shaft to the right.
Turn the bobbin clockwise, by hand, until the
spring on the shaft slides into the groove of
the bobbin.
a Spring on the shaft
b Groove of the bobbin
e
Turn on the sewing machine.
1 Pulling it in as far as
possible.
● Only use bobbins (part code: SA156, SFB) that have been designed for this sewing machine. Using other
bobbins may cause damage to the machine.
● We designed the bobbin that comes with this machine. If you use bobbins from other models, the
machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the
same type (part code: SA156, SFB).
CAUTION
Actual size
This model Other models
11.5 mm
(7/16 inch)
● If the spool of thread is not in the right place,
the thread may tangle on the spool pin.
CAUTION
1
2
13
1
f
While holding the end of the thread, gently
press the foot controller or press (start/
stop button) (for models equipped with the
start/stop button) to wind the thread around
the bobbin a few times. Then stop the
machine.
Note
● If the sewing machine is to be operated
using the foot controller, connect the foot
controller before turning on the machine.
● When the foot controller is plugged in, the
start/stop button cannot be used to start
sewing (only for models equipped with the
start/stop button).
g
Trim the excess thread above the bobbin.
h
Slide the sewing speed controller to the right
(to set the speed to fast) (for models equipped
with the sewing speed controller).
a Sewing speed controller
i
Press the foot controller or press (start/
stop button) (for models equipped with the
start/stop button) to start.
j
When the bobbin seems full and begins
spinning slowly, take your foot off the foot
controller or press (start/stop button) (for
models equipped with the start/stop button).
k
Cut the thread, slide the bobbin winder shaft
to the left and remove the bobbin.
l
Slide the sewing speed controller back to its
original position (for models equipped with
the sewing speed controller).
Memo
● When the sewing machine is started or the
handwheel is turned after winding the
thread around the bobbin, the machine will
make a clicking sound; this is not a
malfunction.
● The needle bar does not move when you
slide the bobbin winding shaft to the right.
● Make sure you follow the instructions
carefully. If you do not cut the thread
completely, and the bobbin is wound, when
the thread runs low it may tangle around the
bobbin and cause the needle to break.
CAUTION
● Not winding the bobbin properly may cause
the thread tension to loosen, and may break
the needle.
a Wound evenly
b Wound poorly
CAUTION
1
2
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
—
14
■ For models equipped with the fast bobbin
winding system
a
Follow steps 1 through 2 of the procedure in
“Winding the bobbin” to pass the thread
around the pre-tension disk (page 12).
b
Place the bobbin on the bobbin winder shaft
so that the spring on the shaft fits into the
notch in the bobbin.
a Notch
b Bobbin winder shaft spring
c
Slide the bobbin winder shaft to the right.
d
While holding the thread that wraps around the
pre-tension disk with your left hand, use your
right hand to wind the free end of the thread
clockwise around the bobbin five or six times.
e
Pull the thread to the right and pass it through
the slit in the bobbin winder seat.
a Slit in bobbin winder seat (with built-in cutter)
X The thread is cut to a suitable length.
f
Slide the sewing speed controller
to the right
(to set the speed to fast) (for models equipped
with the sewing speed controller).
a Sewing speed controller
g
Turn on the sewing machine.
h
Press the foot controller or press (start/
stop button) (for models equipped with the
start/stop button) to start.
Note
● If the sewing machine is to be operated
using the foot controller, connect the foot
controller before turning on the machine.
● When the foot controller is plugged in, the
start/stop button cannot be used to start
sewing (only for models equipped with the
start/stop button).
i
When the bobbin begins spinning slowly, take
your foot off the foot controller or press
(start/stop button) (for models equipped with
the start/stop button).
j
Cut the thread, slide the bobbin winder shaft
to the left and remove the bobbin.
k
Slide the sewing speed controller back to its
original position (for models equipped with
the sewing speed controller).
●
Be sure to cut the thread as described. If the bobbin is
wound without cutting the thread using the cutter built
into the slit in the bobbin winder seat, the thread may
become tangled in the bobbin or the needle may bend
or break when the bobbin thread starts to run out.
CAUTION
●
Not winding the bobbin properly may cause the
thread tension to loosen, and may break the needle
.
a Wound evenly
b Wound poorly
CAUTION
1
2
15
1
Memo
● When the sewing machine is started or the
handwheel is turned after winding the
thread around the bobbin, the machine will
make a clicking sound; this is not a
malfunction.
● The needle bar does not move when you
slide the bobbin winding shaft to the right.
Lower threading
Install the bobbin wound with thread.
• For more details on quick-set bobbin, see page 16.
a
Raise the needle to its highest position by turning
the handwheel toward you (counterclockwise) or
press (needle position button) (for models
equipped with the needle position button), and
raise the presser foot lever.
b
Slide the button and open the cover.
a Cover
b Slide button
c
Put the bobbin in so the thread comes out in
the direction shown by the arrow.
• Only use bobbins that were designed to be
used with this machine.
d
Hold the end of the thread, push the bobbin
down with your finger, and then pass the
thread through the slit, as shown.
• If the thread is not correctly inserted through
the tension-adjusting spring of the bobbin
case, it may cause incorrect thread tension
(page 31).
a Tension-adjusting spring
● Winding the bobbin improperly may cause
the thread tension to loosen, breaking the
needle and resulting in injury.
a Wound evenly
b Wound poorly
● The bobbin was designed specifically for this
sewing machine. If bobbins from other
models are used, the machine will not operate
correctly. Use only the enclosed bobbin or
bobbins of the same type (part code: SA156,
SFB).
● Make sure you turn the power off while
threading the machine. If you accidentally
step on the foot controller and the machine
starts to sew, you could be injured.
CAUTION
1
2
Actual size
This model Other models
11.5 mm
(7/16 inch)
CAUTION
● Make sure you set the bobbin so the thread
unrolls in the right direction. If the thread unrolls
in the wrong direction, it may cause the thread
tension to be incorrect or break the needle.
12
CAUTION
1
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
—
16
e
Replace the bobbin cover. Put the left tab in
place (see arrow a), and then press lightly on
the right side (see arrow b) until the cover
clicks into place.
• Replace the cover so that the end of the
thread comes out from the left side of the
cover (as shown by the line in the diagram).
■ For models equipped with the quick-set bobbin
a
Raise the needle to its highest position by turning
the handwheel toward you (counterclockwise) or
press (needle position button) (for models
equipped with the needle position button), and
raise the presser foot lever.
b
Slide the button and open the cover.
a Cover
b Slide button
c
Put the bobbin in, feed the end of the thread
through the slit, and then pull the thread to cut it.
• Only use bobbins that were designed to be
used with this machine.
a Cutter
• If the thread is not correctly inserted through
the tension-adjusting spring of the bobbin
case, it may cause incorrect thread tension
(page 31).
a Tension-adjusting spring
Memo
● The order that the bobbin thread should be
passed through the bobbin case is indicated
by marks around the bobbin case. Be sure
to thread the machine as indicated.
d
Replace the bobbin cover. Put the left tab in
place (see arrow a), and then press lightly on
the right side (see arrow b) until the cover
clicks into place.
Memo
● You can begin sewing immediately without
drawing up the bobbin thread. If you want
to draw up the bobbin thread before you
start to sew, follow the procedure in
“Drawing up the lower thread” (page 20).
● Make sure you set the bobbin so the thread
unrolls in the right direction. If the thread unrolls
in the wrong direction, it may cause the thread
tension to be incorrect or break the needle.
12
CAUTION
1
1
17
1
Upper threading
Set the upper thread and thread the needle.
• For details on the needle threader, see page 18.
a Spool pin
b Thread guide
c Mark on the handwheel
a
Raise the presser foot using the presser foot
lever.
a Presser foot lever
b
Raise the needle by turning the handwheel
toward you (counterclockwise) so that the
mark on the wheel points up, or press
(needle position button) (for models equipped
with the needle position button) once or twice
to raise the needle.
• If the needle is not correctly raised, the
sewing machine can not be threaded. Be
sure to turn the handwheel so that the mark
on the wheel points up before threading the
sewing machine.
● Make sure you thread the machine properly. Otherwise, the thread could tangle and break the needle.
CAUTION
a Mark b Needle position button
or
KNOWING YOUR SEWING MACHINE ————————————————————————————————————————
—
18
c
Pull up the spool pin as far as possible, and
then put a spool of thread on this pin.
d
Feed the upper thread as shown in the figure
on the previous page.
e
Make sure you guide the thread through the
thread take-up lever from right to left.
a Thread take-up lever
f
Put the thread behind the needle bar thread
guide above the needle.
The thread can easily be passed behind the
needle bar thread guide by holding the thread
in your left hand, then feeding the thread with
your right hand.
a Needle bar thread guide
g
Thread the needle from front to back and pull
out about 5 cm (2 inch) of thread.
a 5 cm (2 inch)
Note
● If the thread take-up lever is lowered, the
upper thread cannot be wrapped around the
thread take-up lever. Make sure you raise
the presser foot lever and the thread take-up
lever before you feed the upper thread.
● If you incorrectly feed the thread you may
cause sewing problems.
■ Using the needle threader (for models
equipped with the needle threader)
a
Follow steps 1 through 6 of the procedure in
“Upper threading” to thread the machine to
the needle bar thread guide.
b
Lower the presser foot lever.
c
While lowering the needle threader lever,
hook the thread onto the guide.
a Needle holder
b Needle threader lever
c Guide
● If the spool of thread is in the wrong place, or
is set incorrectly, the thread may tangle on
the spool pin and cause the needle to break.
CAUTION
● The needle threader can only be used with
home sewing machine needles size 75/11-
100/16. Check the table on page 21 for the
appropriate needle and thread combinations.
If you are using transparent nylon mono-
filament thread, you can only use needles in
the range of 90/14-100/16.
● You cannot use the needle threader if you are
using decorative threads or special needles,
such as the twin needle and wing needle.
If you are using those types of threads or
needles, thread the eye of the needle by hand.
Make sure the main power switch is off when
threading the needle by hand.
CAUTION
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
