King Canada 8030L User manual

Brand: King Canada

Model: 8030L

Type: User manual

This manual is also suitable for

8030LK-BC

20V MAX LITHIUM-ION

CORDLESS VARIABLE SPEED

RECIPROCATING SAW

INSTRUCTION MANUAL

MODEL: 8030L

04/2017

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

FOR THIS 20V RECIPROCATING SAW

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and

durability standards. King Canada warrants to the original retail consumer a 2-year

limited warranty as of the date the product was purchased at retail and that each

product is free from defects in materials. Warranty does not apply to defects due

directly or indirectly to misuse, abuse, normal wear and tear, negligence or

accidents, repairs done by an unauthorized service center, alterations and lack of

maintenance. King Canada shall in no event be liable for death, injuries to persons

or property or for incidental, special or consequential damages arising from the use

of our products.

To take advantage of this limited warranty, return the product at your expense

together with your dated proof of purshase to an authorized King Canada service

center. Contact your retailer or visit our web site at www.kingcanada.com for an

updated listing of our authorized service centers. In cooperation with our authorized

serviced center, King Canada will either repair or replace the product if any part or

parts covered under this warranty which examination proves to be defective in

workmanship or material during the warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and

references are subject to change without prior notice.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts

diagram and parts list.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

1. KNOW YOUR TOOL

Read and understand the instruction manual and labels affixed to the tool. Learn its

application and limitations as well as its specific potential hazards.

2. Don’t use power tools in damp or wet locations or expose them to rain. Keep work area

well lit and provide adequate surrounding work space.

3. USE RIGHT TOOL.

Don’t force the tool or the attachment to do a job for which it was not designed.

4. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could

get caught in moving parts. Non-slip footwear is recommended. Wear protective hair

covering to contain long hair. Roll up long sleeves above the elbows.

5. MAINTAIN TOOL WITH CARE.

Keep tool clean for best and safest performance. Follow instructions for operation and

changing accessories.

6. DISCONNECT TOOLS.

Before servicing, when changing accessories or attachments.

7. AVOID ACCIDENTAL STARTING.

Make sure the switch is in the ‘’OFF’’ position before connecting battery.

8. USE RECOMMENDED ACCESSORIES.

Consult the manual for recommended accessories. Follow the instructions that

accompany the accessories. The use of improper accessories may cause hazards.

9. CHECK FOR DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are damaged should be

carefully checked to ensure they will operate properly and perform their intended

function. Check for alignment of moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A guard or other parts which are damaged

should be properly repaired or replaced.

Specific Safety Instructions

1. Only use King attachments and accessories, serious injury can result if this warning is

not respected.

2. Before installing or changing an accessory, remove the battery from the tool.

3. Hold power tool by insulated grip surface, an accessory could contact hidden wiring,

contact with a “live” wire will make exposed metal surfaces “live” and will shock the

operator.

4. Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

stoves and refrigerators. Risk of electric shock if your body is grounded.

5. Use clamps or any other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to

loss of control.

6. Wear protective gloves and safety glasses, an accessory can become extremely hot

during operation, danger of burns!

7. Do not use the tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

GENERAL & SPECIFIC

SAFETY INSTRUCTIONS

LITHIUM-ION BATTERY &

CHARGER INFORMATION

WARNING: The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be understood

by the operator that common sense and caution are factors which cannot be built into this

product, but must be supplied by the operator. Do not plug in charger or install battery into

saw until you have read and understood this instruction manual.

King canada offers a variety of 20V max Lithium-ion Power Tools which can all use the

same battery and battery charger. The obvious advantage is not having to purchase

separate batteries and chargers for each tool. (Battery and charger sold separately).

Available batteries and charger for this 20V max Li-ion Reciprocating Saw:

• 1.3 Ah 20V max Lithium-ion battery (Model K-020LBT)

• 3.0 Ah 20V max Lithium-ion battery (Model K-023LBT-3)

• 20V max Lithium-ion battery charger (Model K-020LCG)

Charging any other battery may damage the charger and possibly cause serious injury.

Battery and Charger Safety Precautions

1) Do not store or carry battery in a way which metal objects could contact the exposed

metal end of the battery. The battery could short-circuit causing a fire, personal injury

and damage to the battery.

2) Never attempt to open the battery for any reason. If battery housing has cracked,

discontinue use immediately and do not try to recharge it. Dispose of battery.

3) Never charge a wet battery or a battery that shows signs of corrosion.

4) Do not use an extension cord with the charger, plug charger directly into a 120V AC

receptacle.

5) Do not use charger if power cord is damaged, replace damaged cord or charger.

6) Do not charge battery when work area or the battery temperature is or below 0

C or

above 45

7) Unplug charger when not in use.

8) It is important to recycle or dispose of battery properly at your nearest battery

recycling location.

9) The contents of the battery is slightly acidic, do not incinerate the battery, it can

explode in a fire.

10) A small leakage from the battery may occur under extreme usage, charging or

temperature conditions. This does not indicate a battery failure. However, if the battery

housing is cracked and leakage gets on your skin, follow these steps;

-Wash with soap immediately.

-Neutralize area with mild acid such as vinegar or lemon juice.

-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes, then

seek medical attention.

Lithium-ion Battery

Lithium-ion batteries do not have a memory and do not require to be completely

discharged periodically. After use, charge battery so that it is fully charged for the next time

you use this tool. A fully charged battery will only loose about 2% of its charge per month

during storage.

GETTING TO KNOW YOUR TOOL

SPECIFICATIONS

Model ........................................................................................................................8030L

Voltage ................................................................................................................20V MAX

Blade stroke ....................................................................................................................1”

Variable speed ..............................................................................................0-3,000 SPM

Weight ......................................................................................................................3.6 lbs

Battery types (not included) ..........1.3Ah (Mod. K-020LBT) or 3.0Ah (Mod. K-023LBT-3)

Battery charger (not included) ..................................................................Mod. K-020LCG

1. Blade (Wood blade installed)

2. Pivot shoe

3. Tool-less blade clamp

4. Safety start button

5. Variable speed trigger

6. 20V MAX Li-ion battery compartment

Figure 1

Unpacking your Reciprocating Saw

Your saw has been shipped completely assembled, except for the blade, and is ready for

use. Inspect it carefully to make sure no breakage or damage has occurred during

transport. If any parts are missing, do not attempt to use the tool until you have obtained

the missing parts from your King Canada retailer.

Contents:

1- Reciprocating saw assembly

1- Wood Cutting Blade

1- Metal Cutting Blade

OPERATION

USING YOUR 20V MAX LITHIUM-ION CORDLESS

RECIPROCATING SAW

Important Note: This Reciprocating Saw does not come

with a battery or charger, if you already own a 20V max

Li-ion cordless tool you may use its battery (K-020LBT)

and charger (K-020LCG) as they are interchangeable. If

not, it will be necessary to purchase a battery and

charger.

WARNING: Do not install battery until the accessory is

installed securely to the tool. Wear protective gloves

and safety glasses, an accessory can become extremely

hot during operation, danger of burns!

Charging the battery/battery level indicator

20V max Li-ion batteries come with a battery power level

indicator (A) Fig.2, press the button (B) to see the charge

level. If the battery level is low charge the battery. To

charge the battery (C) Fig.2, plug charger (D) power cord

into a 120V AC receptacle (do not use extension cord).

The green LED (E) will flash to indicate power to the

charger. Align the grooves the battery with those of the

charger and slide the battery all the way until it snaps into

place. The red LED (F) will light up indicating the

charging procedure has begun. Once the green LED (E)

lights up, the battery is fully charged and ready to use.

Press the battery clip (B) Fig.3 to remove battery from

charger.

Installing/removing battery from drill

To install a battery (A) Fig.3 to the base of the cordless

Reciprocating saw, align the grooves of the battery with

those of the saw base and slide the battery all the way

until the battery clip (B) snaps and holds the battery into

place.

To remove the battery from the base, press the battery

clip (B) Fig.3 and slide the battery away from the base.

Turning Tool On/Off

To turn your Reciprocating Saw ON, depress and hold the safety button (A) Fig.4, then

depress the trigger (B). Release trigger to turn your saw OFF.

Variable speed trigger

Your cordless Reciprocating Saw is equipped with a variable speed trigger (B) Fig.4. The

speed can be controled from the minimum to the maximum strokes/min just by the

pressure applied to the trigger. Apply more pressure to increase speed and apply less

pressure to decrease speed. Release trigger to stop saw.

Figure 2

Figure 3

Figure 4

OPERATION

Blade selection

To obtain the best performance from your saw it is

important to select a specific blade for the particular

application and type of material you wish to cut. By doing

this you will get a smoother, faster cut and prolong blade

life.

Installing a blade

• DISCONNECT BATTERY FROM TOOL BASE.

1) To install a blade into the “tool-less blade change

system”, with the Reciprocating Saw positioned as shown in Fig.5, simply turn the spring

tension blade clamp (A) Fig.5 counterclockwise and hold it in this position.

2) Insert the saw blade (B) through the pivot shoe (C) and then into the blade clamp (A).

3) Once the blade is fully inserted into the blade clamp, release the spring tension blade

clamp to lock the blade in place. Before using, make sure the blade is secure and can

not be pulled out of the spring tension blade clamp.

Warning! Before removing a blade after any operation, let the blade cool down before

attempting to remove it and touching it with your fingers, risk of burning!

CUTTING OPERATION

WARNING: Hold tool by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

General Cutting

Hold your saw firmly in front of and clearly away from you. Make sure saw blade is clear

of any foreign material. Be sure material to be cut is held firmly. Small work pieces should

be securely clamped in a vise or with clamps to the work bench or table. Mark the line of

cut clearly. Start the Reciprocating Saw, set the pivot shoe assembly against the work, then

move the blade into the work. DONOT FORCE. Use only enough pressure to keep the

saw cutting. Let the blade do the work.

Plunge Cutting

Mark the line of cut clearly. Choose a convenient starting point inside the area to be cut out

and place the tip of the blade over that point. Rest front edge of pivot shoe assembly on

work and hold firmly in position.

Figure 5

OPERATION & MAINTENANCE

Plunge Cutting... continued

WARNING: Make sure blade does not touch work until motor reaches full speed, since this

can cause loss of control resulting in serious injury.

With saw blade at full cutting speed, slowly tilt saw downward until tip of blade starts

cutting work. After blade penetrates work, tilt saw until it is perpendicular to the work.

Metal Cutting

Metals such as sheet steel, pipe, steel rods, aluminum, brass and copper may be cut with

your saw. Be careful not to twist or bend the saw blade. DONOTFORCE. We recommend

cutting oil when cutting most soft metals and steel. Cutting oil will also keep blades cool,

increasing cutting action, and prolonging blade life.

Clamp the work firmly and cut close to the clamping point to eliminate any vibration of the

work being cut. When cutting conduit pipe or angle iron, clamp work in a vise if possible

and cut close to the vise. To cut thin sheet material, “sandwich” the material between hard-

board or plywood and clamp the layers to eliminate vibration and material tearing.

MAINTENANCE

WARNING: THERE ARE NO USER SERVICE-ABLE PARTS INSIDE

Preventative maintance performed by an unauthorized personnel may result in the

misplacement of internal wires and componenets which could cause serious hazards. We

recommend that all servicing be performed by a qualified KING CANADA service centre

technician.

Battery

Pay attention to the battery power levels as the battery nears its end of life. If you notice a

decrease in battery performance or a significant difference in running power between

charges, then it is time to replace the battery. Failure to do so may damage the charger

and cause improper operation.

Cleaning

To avoid accidents, always remove the battery from the tool before cleaning. The tool is

most effectively cleaned with the use of an air compressor. Always wear safety glasses

when using an air compressor. Ventilation openings and switch levers must be kept clean

and free of foreign objects. Do not insert pointed objects through these openings in the

attempt to clean them.

1. Air vents of the tool should be cleaned regularly to avoid overheating of the motor which

is caused by the blocking of the air vents.

2. DON’T clean this tool with water, as no liquid is allowed in the tool body. Clean the tool

with a dry clean cloth only. Compressed air at low pressure is also suitable.

3. DON’T allow petroleum based products to come into contact with the plastic parts of the

tool, as they contain chemicals that can damage or destroy the plastic parts.

King Canada 8030L User manual

Brand: King Canada

Model: 8030L

Type: User manual

This manual is also suitable for

8030LK-BC

Download PDF

report

King Canada 8030L User manual

This manual is also suitable for

King Canada 8030L User manual

Related papers

Other documents