Logik L10HC10 User manual
- Category
- Hair trimmers & clippers
- Type
- User manual
Logik L10HC10 is a hair clipper designed for personal use. It comes with four comb attachments that allow you to cut hair to different lengths (3mm, 6mm, 9mm, 12mm). The clipper also features an adjustable lever that lets you control the amount of hair to be cut. The clipper is powered by a 230V~, 50Hz, AC power supply and has a power consumption of 10W. It has a hanging loop for easy storage and a cleaning brush for easy maintenance. The clipper is not suitable for commercial use and should not be left unattended when switched on or connected to the mains supply.
Logik L10HC10 is a hair clipper designed for personal use. It comes with four comb attachments that allow you to cut hair to different lengths (3mm, 6mm, 9mm, 12mm). The clipper also features an adjustable lever that lets you control the amount of hair to be cut. The clipper is powered by a 230V~, 50Hz, AC power supply and has a power consumption of 10W. It has a hanging loop for easy storage and a cleaning brush for easy maintenance. The clipper is not suitable for commercial use and should not be left unattended when switched on or connected to the mains supply.
GB-4 GB-5
Hair Clipper
Instruction Manual
L10HC10
SAFETY FIRST!
Please follow all the safety precautions listed below for safety and to reduce the risk
of injury or electrical shock.
• Check if the voltage indicated on the appliances corresponds to the mains voltage
in your home before you connect the appliance.
• Do not damaged the appliance.
• Do not use the appliance when one of the attachments is damaged or broken as
this may cause injury.
• Keep the appliance out of the reach of children.
• Use and store the appliance at a temperature between 15c and 35c.
• Always unplug the appliance after use.
• This appliance is only intended for clipping human hair. Do not use it for any other
purpose.
• Do not immerse the appliance in water or any other liquid.
• Do not expose the appliance to excessive moisture, dust or dirt
• Always check the blades for alignment.
• Always add a few drops of oil before use.
• Do not use the appliance if the teeth are damaged.
• Always check the appliance for damage before use. If any damage is observed, do
not use the appliance.
• This appliance has no user repairable parts.
• The appliance can become hot during use , only use for 10 minutes ON 10 minutes
OFF three cycle .
• Always let the appliance cool down before storing.
• This appliance is for personal use only. It is not suitable for commercial use.
• This appliance should not be left unattended when switch on or when connected
to mains supply.
• Do not wrap the mains lead around the appliance when hot or when storing.
• Do not carry the appliance by the mains lead.
• Do not use with wet hands.
• Do not use the appliance on damaged or broken skin.
• The appliance should never be left unattended when connected to the mains
supply.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instructions concerning the use of the
appliance by a person responsible for their safety.
• If the mains cable is damaged it must be replaced by the manufacturer, its service
agent, or similarly qualied persons in order to avoid a hazard.
WARNING : Keep the appliance dry.
SPECIFICATIONS
Power supply : 230V~, 50Hz, AC Power
Power Consumption : 10W
We continually strive to improve our products, specications may change without
prior notice.
DGS Retail Ltd • Maylands Avenue • Hemel Hempstead •
Herts • HP2 7TG • England
Visit Partmaster.co.uk today for the easiest way to
buy electrical spares and accessories. With over 1
million spares and accessories available we can
deliver direct to your door the very next day. Visit
www.partmaster.co.uk or call 0870 6001 338 (UK customers only) Calls charged at
National Rate.
This symbol on the product or in the instructions means that your
electrical and electronic equipment should be disposed at the end of
its life separately from your household waste. There are separate
collection systems for recycling in the EU. For more information, please
contact the local authority or your retailer where you purchased the
product.
Congratulations on the purchase of your new Logik
Hair Clipper.
We recommend that you spend some time reading this
instruction manual in order to fully understand all the
operational features it offers.
Read all the safety instructions carefully before use and keep
this instruction manual for future reference.
Unplug the hair clipper before you start cleaning it.
GB-1 GB-2 GB-3
UNPACKING
Remove all packaging from the hair clipper. Retain the packaging. If you dispose of it
please do so according to any local regulations.
The following items are included:
• The Main Unit
• Four Comb Attachments:
3mm (1/8”): (P.N.: RAY911-009) 6mm (1/4”): (P.N.: RAY911-010)
9mm (3/8”): (P.N.: RAY911-011) 12mm (1/2”): (P.N.: RAY911-012)
• The Teeth Guard (P.N.: RAY911-008) • The Lubricating Oil (P.N.: RAY911-038)
• The Cleaning Brush (P.N.: RAY911-041) • The Comb (P.N.: RAY911-013)
• The Scissors (P.N.: RAY913-056) • Instruction Manual (P.N.: L10HC10-001)
If items are missing or damaged, please contact Partmaster (UK only).
Tel: 0870 6001 338 for assistance.
NOTE
Your hair clipper has a power dial. It has already been adjusted for peak eciency
before leaving the factory. However, if you experience the speed has decreased. You
will need to adjust the dial.
1. Turn on the hair clipper.
2. Use a tool to insert into the power dial.
3. Gently turn the dial clockwise until you
hear the vibration sound noticeably
increase.
4. Then turn slightly anticlockwise, stop as
soon as the sound disappeares.
FIRST TIME USE
1. Make sure the Power switch is set to 0 (Off).
2. Remove the plastic protective cover from the cutting blade.
3. Lubricate the cutting blades with a couple of drops of oil before using the unit for
the rst time and before using it on each further occasion.
(Lubricating oil tip was sealed, open the tip with cutter or scissors.)
PRODUCT OVERVIEW
OPERATION
Fitting comb attachments
The hair clipper is supplied with 4 comb attachments that are used to trim the hair to
one of 4 different lengths:
• Comb is used to trim hair to a length of 3mm (1/8”).
• Comb is used to trim hair to a length of 6mm (1/4”).
• Comb is used to trim hair to a length of 9mm (3/8”).
• Comb is used to trim hair to a length of 12mm (1/2”).
Using the hair clipper without a comb attachment will cut off hair with cutting length
of around 1.5mm. You can use the adjusting lever on the side of the hair clipper to
control the amount of hair to be cut. Lower the lever down for less hair; raise the lever
up for more hair.
Slide one of the comb attachments over the head of the hair clipper’s xed cutting
blade.
Using the hair clipper
1. Before you start clipping, make sure the head of the person
whose hair you are cutting is at the same level as your chest.
2. To get the best results, use the hair clipper only on dry hair.
Do not use it on freshly washed hair.
3. First comb the hair into the direction of hair growth.
4. Switch power switch to “I” on position.
5. Always move the hair clipper against the direction of hair
growth, otherwise it will not cut the hair properly.
6. Move the hair clipper through the hair slowly.
Clipping with comb attachment
1. Slide the comb attachment onto the rails on the hair clipper.
• Select the small or large comb attachment, depending on
the desired hair length.
2. Make sure that the arms of the comb attachment have been
properly slid onto the rails on both sides.
• Hair length settings
The hair length settings are indicated in millimetres on the
arms of the comb attachment. The settings correspond to
the remaining hair length after cutting.
3. Start at the setting for maximum hair length.
4. Make sure that the at part of the comb attachment is
always fully in contact with the scalp to obtain an even
cutting result.
5. Pass the hair clipper slowly over the crown from different
directions to achieve an even cutting result.
6. Make overlapping passes over the head to ensure that the
hair clipper catches all the hairs that need to be cut.
7. Comb the hair in the direction of hair growth from time to
time so that the hair clipper can catch the hair more easily.
8. To achieve a good result with curly, sparse or long hair, you
can use a comb to guide the hair towards the hair clipper.
PRECISE CONTOURING WITHOUT COMB ATTACHMENT
1. Remove the comb attachment by pulling it off the hair clipper.
2. Before contouring the hairline round the ears, comb the hair ends over the ear.
3. Bend the person's ear to get it out of the way.
1
2
3
4
Comb Attachments
Power Dial
Teeth Guard
Comb
Lubricating Oil Cleaning Brush Scissors
1 2 3 4
4. Tilt the hair clipper in such a way that
only one edge of the cutting element
touches the hair ends.
5. Only cut the hair ends. The hairline
should be close to the ear.
6. To contour the nape hairline and the
sideburns, turn the hair clipper and
make downward strokes.
7. Move slowly and smoothly. Just
follow the natural hairline.
GRADUATION
The hair clipper not only allows you to cut the hair evenly at the same length all over
the head, it also enables you to achieve a smooth transition from longer hair on top
of the head to shorter hair on the back and sides of the head.
1. Start clipping at the setting for maximum hair length.
2. Then choose a shorter setting and cut the hair on all parts of the head except the
top, where you want the hair to be longer.
3. You can repeat this procedure until the hair on every part of the head has the
desired length.
CUTTING OVER STYLING COMB OR FINGERS
This technique can be used to obtain hair lengths over 41 mm and 21 mm. Bear in
mind that this technique is dicult to master and should only be applied by
experienced users.
1. Make sure the comb attachment is not attached to the
hair clipper.
2. Comb a small section of hair upwards. Lift the hair with a
styling comb or hold it between your ngers until only
the length that needs to be cut sticks out.
3. Cut the hair protruding from the comb or ngers.
4. Continue this procedure and comb frequently to remove
cut hair and to check for unevenly cut sections.
CLEANING & STORAGE
Clean the hair clipper after every time you use it. Do not use abrasives, scourers or
liquids such as alcohol, petrol or acetone to clean the hair clipper.
1. Make sure the hair clipper is switched off and
unplugged.
2. Make sure the comb attachment is not attached to the
hair clipper. Never pull at the exible top of the comb
attachment. Always pull at the bottom part.
3. Push the middle part of the cutting unit upwards with
your thumb until it opens and then pull it off the hair
clipper. Be careful that the cutting unit does not fall to
the oor.
4. Clean the cutting unit and the inside of the hair clipper with the brush supplied.
5. Place the lug of the cutting unit into the slot and push the unit back onto the hair
clipper ('click').
Hanging
Loop
Cutting
Blade
Adjustable
Lever
Power Switch
Mains Cable
1
2
-
1
-
2
Logik L10HC10 User manual
- Category
- Hair trimmers & clippers
- Type
- User manual
Logik L10HC10 is a hair clipper designed for personal use. It comes with four comb attachments that allow you to cut hair to different lengths (3mm, 6mm, 9mm, 12mm). The clipper also features an adjustable lever that lets you control the amount of hair to be cut. The clipper is powered by a 230V~, 50Hz, AC power supply and has a power consumption of 10W. It has a hanging loop for easy storage and a cleaning brush for easy maintenance. The clipper is not suitable for commercial use and should not be left unattended when switched on or connected to the mains supply.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI