TEAC K-07 Owner's manual

D01163921B

K

-

07

Super Audio CD/CD Player

OWNER’S MANUAL .................... 5

MODE D’EMPLOI ...................... 35

MANUAL DEL USUARIO ........... 65

Page is loading ...

3

CAUTION

DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE o

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, o

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF o

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

IN NORTH AMERICA USE ONLY ON 120 V SUPPLY.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

For Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-

003 du Canada.

For U.S.A.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to this equipment not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

China RoHS

The information in the following table is only applicable to products for sale in the People’s Republic of China. o

The products sold in the European area are manufactured in accordance with the European RoHS Directive. o

.

IMPORTANT SAFETY PRECAUTIONS (1)

4

This product has been designed and manufactured according to FDA

regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified as

class laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

For U.S.A.

Laser :

Type : SLD6163RL-G

Manufacturer : SONY CORPORATION

Laser output : Less than 1mW on the objective lens

Wavelength : 785±15 nm (CD)

655±10 nm (Super Audio CD)

Q Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading

to fire, injury or the staining of nearby things. Please read and

observe the following precautions carefully.

Be sure to insert the batteries with correct positive ( o +) and

negative (_) orientations.

Use batteries of the same type. Never use different types of o

batteries together.

If the remote control is not used for a long time (more than a o

month), remove the batteries to prevent them from leaking.

If the batteries leak, wipe away the leakage inside the battery o

compartment and replace the batteries with new ones.

Do not use batteries of types other than those specified. Do o

not mix new batteries with old ones or use different types of

batteries together.

Do not heat or disassemble batteries. Never throw batteries into o

fire or water.

Do not carry or store batteries with other metallic objects. The o

batteries could short circuit, leak or explode.

Never recharge a battery unless it is confirmed to be a o

rechargeable type.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms

or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

The apparatus draws nominal non-operating power from the o

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

The mains plug is used as the disconnect device, the disconnect o

device shall remain readily operable.

Caution should be taken when using earphones or headphones o

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

Do not expose this apparatus to drips or splashes. o

Do not place any objects filled with liquids, such as vases, on o

the apparatus.

Do not install this apparatus in a confined space such as a book o

case or similar unit.

The apparatus should be located close enough to the AC outlet o

so that you can easily reach the power cord plug at any time.

If the product uses batteries (including a battery pack or o

installed batteries), they should not be exposed to sunshine, fire

or excessive heat.

CAUTION for products that use replaceable lithium batteries: o

there is danger of explosion if a battery is replaced with an

incorrect type of battery. Replace only with the same or

equivalent type.

Products with Class construction are equipped with a power

supply cord that has a grounding plug. The cord of such a product

must be plugged into an AC outlet that has a protective grounding

connection.

CAUTION

WARNING

“DSD” is a registered trademark.

“Super Audio CD” is a registered trademark.

Microsoft, Windows XP, Windows Vista and Windows 7 are either

registered trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

Apple, Macintosh and Mac OS X are trademarks of Apple Inc.,

registered in the U.S. and other countries.

Other company names, product names and logos in this document

are the trademarks or registered trademarks of their respective

owners.

IMPORTANT SAFETY PRECAUTIONS (2)

IMPORTANT SAFETY INSTRUCTIONS

5

English

For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be disposed

of separately from the municipal waste stream via collection

facilities designated by the government or local authorities.

(b) By disposing of electrical and electronic equipment correctly,

you will help save valuable resources and prevent any potential

negative effects on human health and the environment.

(c) Improper disposal of waste electrical and electronic equipment

can have serious effects on the environment and human

health because of the presence of hazardous substances in the

equipment.

(d) The Waste Electrical and Electronic Equipment (WEEE)

symbol, which shows a wheeled bin that has been

crossed out, indicates that electrical and electronic

equipment must be collected and disposed of sepa-

rately from household waste.

(e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal and electronic equipment, please contact your city office,

waste disposal service or the shop where you purchased the

equipment.

Disposal of batteries and/or accumulators

(a) Waste batteries and/or accumulators should be disposed of

separately from the municipal waste stream via collection

facilities designated by the government or local authorities.

(b) By disposing of waste batteries and/or accumulators correctly,

you will help save valuable resources and prevent any potential

negative effects on human health and the environment.

(c) Improper disposal of waste batteries and/or accumulators can

have serious effects on the environment and human health

because of the presence of hazardous substances in them.

(d) The WEEE symbol, which shows a wheeled bin that

has been crossed out, indicates that batteries and/

or accumulators must be collected and disposed of

separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or cadmium

(Cd) as defined in the Battery Directive (2006/66/EC), then the

chemical symbols for those elements will be indicated beneath

the WEEE symbol.

(e) Return and collection systems are available to end users. For

more detailed information about the disposal of waste batter-

ies and/or accumulators, please contact your city office, waste

disposal service or the shop where you purchased them.

Pb, Hg, C d

6

Contents What’s in the box

Thank you for choosing Esoteric. Read this manual carefully

to get the best performance from this unit.

Check to be sure the box includes all the supplied accessories

shown below.

Please contact the store where you purchased this unit if any

of these accessories are missing or have been damaged during

transportation.

Remote control unit (RC-1301) x 1

Batteries (AAA) x 2

Power cord x 1

Owner’s manual (this document) x 1

Keep this manual in a safe place for future reference. o

Warranty card x 1

What’s in the box ................................................6

Before use .......................................................7

Discs ............................................................7

Remote control unit ..............................................9

Making connections ............................................10

Names and functions of parts (main unit) ........................12

Names and functions of parts (display) ...........................13

Names and functions of parts (remote control) ...................14

Playback ........................................................16

Selecting tracks .................................................18

Using repeat playback ..........................................19

Using program playback ........................................19

Changing the display ............................................21

D/A converter mode ............................................21

Connecting a computer and playing back audio files .............22

Setting mode ...................................................24

Using the dimmer ...............................................28

Adjusting the volume ...........................................29

Muting the output ..............................................29

Troubleshooting ................................................30

Restoring factory default settings ................................31

Specifications ...................................................32

Rear panel ......................................................33

7

English

Before use

Read this before attempting any operations.

CAUTION

Avoid placing the unit in direct sunlight or close to any source of o

heat, such as radiators, heaters, open fireplaces, amplifiers, etc. Also

avoid locations that are subject to vibrations or exposed to exces-

sive dust, cold or moisture.

Place the unit in a stable location near the audio system that you o

will use.

Do not move the unit during playback. o

During playback, the disc rotates at high speed. Do not lift or move

the unit during playback. Doing so may damage the disc or the

unit.

Be careful to avoid injury when moving the unit due to its weight. o

Get someone to help you if necessary.

The voltage supplied to the unit should match the voltage as o

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

As the unit may become warm during operation, always leave o

sufficient space around the unit for ventilation. Make sure there is

at least 5 cm (2”) of space on each side of the unit. DO NOT place

anything such as a CD, CD-R, LP, cassette tape etc. on top of the

unit.

Do not open the cabinet as this might result in damage to the o

circuitry or cause electric shock. If a foreign object should get into

the unit, contact your dealer or service company.

When removing the power plug from the wall outlet, always pull o

directly on the plug, never yank on the cord.

Always remove the disc before relocating or moving this unit. o

Moving the unit with a disc inside could cause a malfunction.

Depending on the electromagnetic waves of television broadcasts, o

interference might appear on television screens when this unit’s

power is on. This does not indicate that this unit or the TV is mal-

functioning. If this occurs, turn this unit’s power off.

Maintenance

If the surface of the unit gets dirty, wipe it with a soft cloth or use

diluted mild liquid soap. Allow the surface of the unit to dry com-

pletely before using.

Q For safety, disconnect the power cord from the socket before

cleaning.

Never spray liquid directly on this unit. o

Do not use thinner or alcohol as they could damage the surface of o

the unit.

Avoid allowing rubber or plastic materials to touch this product for o

long periods of time, because they could damage the cabinet.

Discs (1)

Discs that can be played on this unit

CDs that bear the “COMPACT disc DIGITAL AUDIO” logo.

12cm (4.7 o ") or 8cm (3.15") discs

Linear PCM digital audio o

Audio CDs are divided into tracks.

Super Audio CDs that bear the “Super Audio CD” logo.

Single layer, dual layer or hybrid layer o

12cm (4.7 o ") discs

Digital audio (DSD) o

Super Audio CDs are divided into tracks.

CD-R and CD-RW discs that have been correctly recorded

in the audio CD format (CD-DA) and finalized.

This unit can play these types of discs without an adapter. It cannot

play any other type of disc.

Q Playback of any other disc type could result in an unpleasant loud

noise, damage to the speakers as well as potential harm to your

hearing. Never play back any other type of disc.

The logo should be on the disc label or the CD jacket. o

DVDs, Video CDs, DVD-ROMs, CD-ROMs and similar types of o

discs cannot be played on this unit.

Copy-protected discs and other discs that do not conform to o

the CD standard might not play correctly in this player. If you

use such discs in this unit, ESOTERIC company and its subsidiar-

ies will not be responsible for any consequences or guarantee

the quality of reproduction. If you experience problems with

such non-standard discs, you should contact their issuers.

Discs created by a CD recorder must be finalized before use o

with this unit. If you are uncertain about the handling of a CD-R

or CD-RW disc, please contact the seller of the disc directly.

Depending on disc quality and recording conditions, playback of

some discs might not be possible. Please see the manual for the

device that you used to create the disc.

8

CAUTION

Do not play any disc that is warped, deformed or damaged. o

Playing such discs could cause irreparable harm to the playing

mechanisms.

While printable CD-R and CD-RW discs utilizing modern printing o

technologies are generally acceptable, older systems that use

adhesives to attach paper type labels to the disc surface are not

recommended.

Do not stick papers or protective sheets on the discs and do not o

use any protective coating sprays.

Never use a stabilizer. Using commercially available CD stabilizers o

with this unit will damage the mechanisms and cause them to

malfunction.

Do not use irregularly-shaped discs (octagonal, heart-shaped, busi- o

ness-card-size, etc.). CDs with these shapes could damage the unit.

Handling precautions

Always insert the disc into the disc tray with the label side up. Only o

one side of a Compact Disc can be played or used for recording.

To remove a disc from its storage case, press down on the center of o

the case and lift the disc out, holding it carefully by the edges.

How to remove the disc How to hold the disc

Storage precautions

Discs should be returned to their cases after use to avoid dust and o

scratches that could cause the laser pickup to “skip.”

Do not expose discs to direct sunlight or high temperature and o

humidity for extended periods. Long exposure to high tempera-

tures will warp discs.

CD-R and CD-RW discs are more sensitive to the effects of heat and o

ultraviolet rays than ordinary CDs. It is important that they are not

stored in locations where they will be exposed to direct sunlight.

They should also be kept away from sources of heat, such as radia-

tors and heat-generating electrical devices.

Maintenance

If a disc becomes dirty, wipe its surface radially from the center o

hole outward towards the outer edge with a soft, dry cloth.

Never clean discs using chemicals such as record sprays, antistatic o

sprays and fluids, and thinner. Such chemicals will do irreparable

damage to the disc’s plastic surface.

If you are in any doubt as to the care and handling of a disc, read the

precautions supplied with the disc or contact the disc manufacturer.

Discs (2)

9

English

Remote control unit

The included remote control allows this unit to be operated from a

distance.

Point the remote control unit at the main unit’s remote sensor

within 23 feet/7 meters of the main unit.

Remote sensor

23 feet/7m

Depending on the angle, reception might be difficult. Use the o

remote control from directly in front of the unit as much as possible.

Even if the remote control unit is used within its effective range, o

operation by remote control might be impossible if there are any

obstacles between the unit and the remote control.

If direct sunlight or strong artificial illumination shines on the o

remote sensor, the remote control might not function.

If the remote control unit is operated near other devices that gen- o

erate infrared rays, or if other remote controls that use infrared rays

are operated near the unit, this unit might operate incorrectly. The

other devices might also operate incorrectly.

Battery Installation

Remove the cover from the back of the remote control and insert

two AAA batteries with their ¥/^ oriented as shown in the case.

Replace the cover.

Battery Replacement

If the operating range required between the remote control unit and

main unit decreases, the batteries are exhausted. In this case, replace

the batteries with new ones.

For more information about collection of batteries, please contact

your local government, your waste disposal service or the point of

sale where you purchased the collection.

10

Q Precautions when making connections

Make all connection before plugging in the power cord. o

Carefully read the operation manuals of the other equipment and follow their instructions when connecting them. o

DIGITAL OUT

(OPTICAL)

DIGITAL OUT

(COAXIAL)

E

F

A A

G

C CB

D

Amplier or digital

recording device

(CD recorder, MD

deck, etc.)

Amplier or digital

recording device

(CD recorder, MD

deck, etc.)

DIGITAL IN

(COAXIAL)

DIGITAL IN

(OPTICAL)

Optical

digital cable

RCA coaxial

digital cable

RCA coaxial

digital cable

USB cable

Optical

digital cable

Digital audio

output deviceComputer

Digital audio

output device

Included power cord

Wall socket

Stereo amplier

Audio input

(LINE IN, etc.)

LLRR

Device that outputs clock

(G-01, G-02, etc.)

WORD SYNC OUT

RCA audio cable

XLR cable

BNC coaxial cable

Connect a

set of

cables of

one type

or the other.

Digital output

can be turned

on/off

(see p.27).

The polarity of the XLR connectors can be

set so that either 2 or 3 is HOT (see p.27).

Making connections

11

English

A

Digital audio output connectors

The DIGITAL OUTPUT connectors will send a digital audio signal

from CDs played on this unit.

Connect a digital audio output connector (COAXIAL or OPTICAL)

to the digital audio input connector of an amplifier or digital

recording device (e.g. CD recorder).

Use commercially available cables for connections.

COAXIAL: RCA digital cable

OPTICAL: optical digital cable (TOS)

These connectors cannot output Super Audio CD digital audio. o

Digital output can be turned on or off (see p.27). o

B

USB input connector

Used to input digital audio from a computer. Connect it to a com-

puter's USB connector.

Use a commercially available USB cable for connection.

Before connecting, read the cautions on pages 22–23. o

C

Digital audio input connectors

Used to input digital audio signals. They can be connected to the

digital output connectors of appropriate audio devices.

They can receive up to 24-bit signals with sampling frequencies

of 32–192 kHz.

Use commercially available cables for connections.

COAXIAL: RCA coaxial digital cable

OPTICAL: optical digital cable (TOS)

D

Analog audio output connectors

These output 2-channel analog audio. Connect the XLR or RCA

connectors to an amplifier.

Use commercially available cables for connections.

XLR: balanced XLR cables

RCA: RCA audio cables

Connect this unit's R connector to the R connector of the amplifier,

and its L connector to the L connector of the amplifier.

o

Analog audio output can be set to either the RCA or XLR connectors

(the XLR polarity can be set for pin 2 or 3 HOT) or OFF (see p.27).

When the XLR connector is selected, the output level can also be o

set (see p.27).

If distortion occurs when the output level is set to +6 dB, set it to

0 dB.

E

Clock sync input connector

Used to input an external clock signal.

Connect the clock sync input connector to the output connector

of a master clock generator.

The following frequencies can be input. o

For CD/SACD:

44.1/88.2/176.4/100 kHz

10/22.5792 MHz

For USB (HS_2) input:

44.1/88.2/176.4/48/96/192/100 kHz

10/22.5792/24.576 MHz

Use a commercially available BNC coaxial cable for connection.

F

Ground connector [SIGNAL GND]

The audio quality may sometimes be improved by connecting

this ground connector to an amplifier or other audio device that

is connected to this unit.

This is not a safety ground. o

G

AC power inlet

Connect the included power cord to this inlet.

After all other connections have been completed, connect the

power plug to the AC power outlet.

Q Do not use any power cord other than an authentic Esoteric

product. Doing so could cause fire or electric shock.

When the unit is not used for an extended period of time,

disconnect the power plug from the outlet.

At Esoteric, we use Esoteric MEXCEL stressfree 8N/7N cables

for reference. The following types of cables in the Esoteric MEXCEL

cable series are available for purchase.

RCA audio cable

XLR audio cable

RCA digital cable

XLR digital cable

BNC digital cable

Power cord

12

A

POWER button

Press to turn the power on and off.

When the power is on, the ring around the button lights blue.

When the power is off, the ring is unlit.

When not using the unit, turn its power off.

B

CLOCK indicator

This shows the clock sync status.

The indicator flashes when a signal is input through the clock

sync input connector and stays lit when locked.

C

MODE button

Press when stopped to select disc playback or an external input

as the source. When set to external input, the unit can be used as

a D/A converter (see p.21).

Press and hold for 2 or more seconds to change to setting mode

(see p.24).

D

Remote control signal receiver

This receives signals from the remote control. When using the

remote control, point the end of it toward this receiver panel (see

p.9).

E

Disc tray

Load a disc for playback here (see p.16).

F

Display

This shows playback time, track number and other information

(see p.13).

C D E J KF GB H IA

G

Tray OPEN/CLOSE button

Press to open and close the disc tray.

H

STOP button

Press to stop playback (see p.17).

Press and hold when stopped for more than 2 seconds to change

the playback area of a Super Audio CD (see p.17).

Press while in setting mode to finish making settings. The CD sta-

tus message appears on the display. (see p.24).

I

PLAY button

Press to start disc playback (see p.16).

During playback, the PLAY indicator lights.

J

PAUSE button

Press to pause playback (see p.17).

When paused, the PLAY indicator flashes.

K

Skip buttons (

.

/

)

Skip forward or backward.

During playback, press and hold for 1 or more seconds to search

forward/backward. Press and hold repeatedly for 1 or more sec-

onds to change the search speed between 3 levels (see p.18).

Use these when in setting mode to change parameters (see p.24).

Names and functions of parts (main unit)

13

English

Names and functions of parts (display)

a

Disc indicator

This shows the type of disc that is loaded.

Super Audio CD: SACD

Standard audio CD: CD

If a DVD-Video (DVD-V), DVD-Audio (DVD-A) or video CD (VCD) o

is loaded, the indicator will light, but the disc cannot be played

back.

b

Repeat indicator ( )

This appears during repeat playback (see p.19)

c

SETUP indicator

This appears when in setting mode (see p.24).

a

b

c

d

e

f

d

Message display area

This shows the playback time and a variety of messages.

e

DOWN MIX indicator

When playing back the multichannel audio of a Super Audio CD,

it is downmixed and output as stereo audio (2 channels). The

DOWN MIX indicator lights at such times.

f

Channel indicator

L and R light during stereo audio (2-channel) playback.

During multichannel audio playback, the indicators that correspond

to the recorded channels light.

14

Names and functions of parts (remote control)

A

C

F

D

H

I

J

L

M

N

K

G

B

E

When the main unit and the remote control both have buttons

with the same functions, this manual explains how to use the but-

ton on the main unit. The corresponding remote control button

can be used in the same manner.

15

English

J

Skip buttons (

.//

)

Press to skip to the previous or next track.

Press and hold for at least one second during playback to scan

forward/backward. Repeatedly press and hold for more than one

second to change the forward/backward scan speed to one of

three levels (see p.18).

They are also used when in setting mode to change parameters

(see p.24).

K

Stop button (

H

)

Press to stop playback (see p.17).

L

Play/Pause button (y/J)

Press when stopped or paused to start playback (see p.16).

Press during playback to pause (see p.17).

M

VOLUME buttons (+/-)

When the attenuator function has been turned on in setting

mode, these can be used to adjust the volume (see p.29).

Use these to adjust the volume of an Esoteric amplifier.

N

MUTE button

When the attenuator function has been turned on in setting

mode, use to temporarily mute the output (see p.29).

Use to mute an Esoteric amplifier.

A

STANDBY/ON button

This button is not used with this unit.

B

Number buttons

Use to select tracks.

C

REPEAT button

Use with repeat playback (see p.19).

Press and hold to enter program mode (see p.19).

D

PLAY AREA button

Press when stopped to change the Super Audio CD playback

area (see p.17).

E

INPUT buttons (k/j)

When stopped, press these buttons to switch between disc play-

back and external input sources. When set to external input, the

unit can be used as a D/A converter (see p.21).

Use this to change the input of an Esoteric amplifier.

F

SETUP button

If the attenuator function has been set to ON, pressing this but-

ton enters setting mode. This has the same function as pressing

and holding the MODE button for 2 or more seconds (see p.24).

This button is disabled when the attenuator function has been

set to OFF in setting mode.

Use to make Esoteric amplifier settings.

G

DIMMER button

Use to adjust the brightness of the main unit's display (see p.28).

H

OPEN/CLOSE button (

L

)

Press to open and close the disc tray (see p.16).

I

DISPLAY button

During playback, press this button to change what is shown on

the display (see p.21).

16

Playback

4

Press the OPEN/CLOSE button.

The disc tray will close. Be careful not to let a finger or any item

get caught in it.

Disc-loading may take some time depending on the amount of o

information on the disc being loaded.

When the disc is loaded, the type of disc, the number of tracks

it contains and the total time of those tracks will appear on the

display (see p.13).

5

Press the PLAY button.

Playback will start.

During playback, the PLAY indicator will light blue.

1 3 54

2

1

Turn the power on.

The ring around the POWER button lights blue.

2

Press the tray OPEN/CLOSE button.

The disc tray opens forward.

3

Place a disc on the center of the tray with its

labeled-side up.

If you close the tray when the disc is not within the central o

guides, the disc could become stuck inside and you might not be

able to reopen the tray. For this reason, you should always place

the disc carefully within the central guides.

17

English

Pausing playback

During playback, press the PAUSE button to pause playback. When

paused, the PLAY indicator on the main unit flashes.

Press the PLAY button or press the PAUSE button again to restart

playback.

Stopping playback

Press the STOP button to stop playback.

Opening and closing the disc tray

Press the OPEN/CLOSE button once to open the tray, and press it

again to close the tray.

If you press the OPEN/CLOSE button during disc playback, several o

seconds will pass before the tray opens.

Changing the playback area

Some Super Audio CDs have multiple areas, including stereo

(2-channel) and multichannel. Hybrid Super Audio CDs have two

layers with one containing ordinary CD-quality audio.

Press the STOP button for 2 or more seconds when the unit is

stopped to change the playback area.

To change the playback area using the remote control, press the o

PLAY AREA button when the unit is stopped.

18

Selecting tracks

Skipping

During playback, press a skip button (

.

/

) on the main unit

or the remote control to skip to the previous or next track and start

playback.

Press the o

.

button once to return to the beginning of the track

that is currently playing. Press the

.

button repeatedly to skip

to an earlier track.

If you press the

.

button when still within the first second of a

track, however, you will skip to the previous track.

When stopped or paused, press a skip button ( o

.

/

) to pause

at the beginning of the selected track.

Using the number buttons to select and play

tracks

During playback or when stopped, press the number buttons to

select a track and start its playback.

Examples:

Track 7

Track 23

Searching forward/backward (scanning)

To scan forward/backward, press and hold the skip (

.

/

)

button on the main unit or the remote control (for more than one

second) during playback. When you find the point where you want

to listen, press the PLAY (

y

) button on the main unit or the play/

pause (

y

/

J

) button on the remote control.

Repeatedly press and hold a skip (

.

/

) button for more than

one second to change the forward/backward scan speed to one of

three levels.

The speed that the < or > flashes on the display also changes.

Ordinary

playback

Speed

(slow)

Speed

(medium)

Speed

(fast)

19

English

Using repeat playback Using program playback (1)

During playback, press the REPEAT button to cycle through the following

repeat modes.

REPEAT TRK

(repeat one track)

REPEAT DSC

(repeat disc)

REPEAT OFF

(ordinary playback)

REPEAT TRK

Repeats playback of the currently playing track. During repeat

playback, if you select a different track, that track will begin playing

back repeatedly.

REPEAT DSC

Repeats playback of all the tracks on the currently playing disc.

Stopping playback disables repeat playback. o

You can program up to 30 tracks in the order that you want to listen

to them.

1

When stopped or during playback, press

and hold the REPEAT button.

If a track is playing, it will become the first track in the program.

2

Use the number buttons to select a track

that you want to add to the program.

Examples Track 3: 3

Track 12: +10 w 2

Track 20: +10 w +10 w 0

Program

item number

Programmed

track number

Continue using the number buttons to program multiple tracks.

Track numbers that do not exist on the currently loaded disc can- o

not be added to the program.

Continued on the next page

20

Using program playback (2)

3

When you have finished adding tracks to the

program, press the play/pause button (

y

/

J

).

Program playback starts.

If you created the program during playback, you do not need to o

press the play/pause button (

y

/

J

).

Adding a track to the end of the program

When stopped or during playback, use the number buttons to

select the number of the track that you want to add.

Clearing the contents of the program and return-

ing to ordinary playback

When stopped or during playback, press the REPEAT button to end

program mode. Press the REPEAT button during program playback

to resume ordinary playback from then on.

This will clear the program contents. o

In addition, when stopped or during playback, if you press the

OPEN/CLOSE button (

L

) or main unit power button, the program

contents will also be cleared.

21

English

Changing the display

When a disc is playing or paused, press the DISPLAY button to change

what is shown on the display in the order shown below.

Example:

Number of track

currently playing

Elapsed time of track

currently playing

Remaining time of

track currently playing

Elapsed time of disc

Remaining time of disc

When stopped, the total number of tracks and the total playback o

time of the disc are shown.

Example:

Total number

of tracks

Total playback

time of disc

This unit can be used as a D/A converter.

When stopped, press the MODE button to show the current source

name. Press the MODE button again to switch between the following

sources. Select one of the external digital inputs (COAX in, OPT in, USB

in).

To do this using the remote control, press an INPUT button when

stopped.

COAX in

(Coaxial

digital input)

OPT in

(Optical

digital input)

CD/SACD

USB in

(USB input for use

with a computer)

When an external input (COAX in, OPT in, USB in) is selected, the o

name and sampling frequency of the selected input appears on

the display. If there is no input signal or the input signal is not

locked, the input sampling frequency is not shown and the input

name flashes.

If the input signal is not a digital audio signal or is an audio signal o

format that is not supported by this unit, including Dolby Digital,

dts and AAC, for example, “–––” appears in place of the sampling

frequency. Set the digital output of the connected equipment to

PCM audio output.

When an external input (COAX in, OPT in, USB in) is selected, disc o

controls other than the OPEN/CLOSE button cannot be used.

D/A converter mode

Page is loading ...

TEAC K-07 Owner's manual

This manual is also suitable for

TEAC K-07 Owner's manual

in other languages

Related papers

Other documents