Craig CHT915 Owner's manual

Brand: Craig

Model: CHT915

Type: Owner's manual

Model: CHT915

This unit has a long cord that can easily be tripped on or pulled on, causing injury,Please make sure

Plastic Base

Washer

Screw

POWER SOURCE

INSTALLATION

AC/DC adapter

to the wall outlet having AC 100-240~;50/60 Hz.

Assemble the plastic base to the main body with the supplied screw and washer as

the figure above.

Insert the small plug from supplied AC/DC adaptor to DC IN jack

on the rear of the unit and insert the AC/DC adaptor

Placing on Floor in Vertical

NOTE:This AC/DC adapter is intended to be correctly

operated in a vented indoor wall outlet.

To the DC IN jack on the rear of unit.

Speaker Net

Remote Sensor

Speakers

Placing on Floor in Vertical (Continued):

The Speaker Net can be take out and reassembled as the figure above.

Placing on Table in Horizontal

Fig.1

To place the unit on a flat surface such like table, insert the 2 (two) supplied

as the Fig.1 below.

Small Slot

Fig.2

Insert the 2 (Two) supplied Plastic Stands into the inner small slot as the Fig. 2 above.

Plastic

Brackets into the small slot of the holder on the rear of unit

Wall Mount

1. Wall mount the unit to the wooden wall

as the Fig.1 below:

Holes distance:31.6 inches

Fig.1

Fig.2

Wooden Wall

supplied screws

supplied bracket

in same horizontal level

Big Slot

B : Put the sound bar onto the Metallic Brackets as Fig.2 below.

Make sure they are firm and stable.

A : Mounted the 2 (Two) supplied Metallic Brackets on the wooden wall by

the 4 (Four) supplied screws

supplied screws

supplied bracket

INSTALLATION

A.Mark the position of the mounting holes on the wall using a pencil.

B.Drill appropriate holes by powerful electric drill on wall.

C.Insert the supplied plastic inserts into the holes by hammer.

2. Mount on Wall

D.Mounted the supplied Metallic Brackets to the holes with supplied screws.

E.Put the unit to the Metallic Brackets as the figure below.

Wall

Big Slot

Mark and drill 4 holes with 31.6 inches distance

in same horizontal level.

Wall Mount (Continued):

MAIN UNIT

1. INDICATOR

2. AUX IN 2 jack

3. SOURCE button

5. EQ (Equalizer) button

8. / TUNE+ button

10. / TUNE- button

7. POWER button

LOCATION OF CONTROLS

AUX IN 2

VOL- VOL+

TUNE-

TUNE+

POWER

SOURCE

990.5

99.0

4. VOL- (Volume Down) button

6. VOL+ (Volume Up) button

DC IN

AUX IN 1

ANT

11. FM Antenna

12. AUX IN 1 jacks

13. DC IN jack

9. (Play/Pause) button

INDICATO R

AUX IN 1

ANT

DC IN

DC 16V, 1.8A

REMOTE CONTROL

SOURCE

TUNE-

TUNE+

VOL

POWER

1. POWER button

2. / TUNE - button

3. VOL (Volume)+/- buttons

4. SOURCE button

5. (Mute) button

6. / TUNE+ button

7. (Play/Pause) button

8. EQ (Equalizer) button

LOCATION OF CONTROLS

BATTERY PRECAUTIONS

Approx.15 feet

Fig.1 Fig.2

Fig.3

Remote Sensor

BATTERY INSTALLATION--- REMOTE CONTROL

EFFECTIVE DISTANCE OF REMOTE TRANSMITTER

-First Time Use

Remove and discard the insulation tab as figure on the right

-Replacing Batteries For Remote Control

1. Push and slide out the battery holder as figure 1 below.

3. Close the battery holder.

2. Replace the battery with a new CR2025 button cell as the polarity

markings on the rear of the Remote Control.

~ Green: Radio

~ Blue: BT(Blue Tooth)

~ Purple: AUX IN 1

~ Orange: AUX IN 2

4. During Playback:

~ Press the VOL (Volume) buttons to adjust volume level as desired.

~ Press the EQ button repeatedly to select and set equalizer mode as desired.

~ Press (Mute) button on the Remote Control to turn off the sound. Press again to resume.

GENERAL OPERATIONS

1. Connect the AC/DC adapter to the unit and wall outlet as the previous procedure .

2. Press the Power button on the unit or remote control to power on the unit from standby mode.

corresponding color as below:

3. Press the SOURCE button repeatedly to switch to desired mode.The color of Indicator will turn

5. When finished listening, press the Power button to power off the unit.The indicator will

turn Red.

The red indicator will light.

6. If long period of time will not use the unit, unplug the AC/DC Adaptor from the wall outlet.

FM Antenna

1. Power ON the unit as previous procedures.

2. Press the SOURCE button repeatedly until the color of the indicator changed to Green.

4. Repeat the same procedures until the desired radio station are received.

3. Press and hold the /TUNE - or /TUNE + buttons until the indicator starts blinking.

The unit will start to search next (or previous) available FM radio station then plays.

The Antenna wire on the rear of the unit is for radio reception. If reception is weak, unwind and

extend the wire or relocate the wire to improve the radio reception.

LISTEN TO FM RADIO

BLUETOOTH PARING AND PLAYBACK

White

Red

AU X I N 1

DVD

3. Power ON the unit as previous procedures.

1. Connect one end of RCA audio connection cable (supplied) to the AUX IN 1 jacks on the rear

of the unit as the figure above.

2. Connect the other end to the Audio out jacks on the external player (such as Television, VCR, DVD

Player, DVR ... etc.).

5. Play the music in the external player as usual. (Make sure the volume output level of the player is

in high level. Otherwise, sound from this unit is weak).

4. Press the SOURCE button repeatedly until the color of indicator turns to Purple.

AUX IN 1 : LISTEN TO TV/DVD/VCR/DVR

Audio out jacks on

TV/DVD/ VCR/DVR

(RCA cable included)

AUX IN 1

4. Press the SOURCE button repeatedly until the color of Indicator turns to Orange.

3. Power ON the unit as previous procedures.

1. Connect one end of supplied audio connection cable to the AUX IN 2 jack on the top of the unit

2. Connect the other end to the Audio out/Line out/Phone jack on the external player (such like iPod,

iPhone, iPad, MP3 player, Discman... etc.).

5. Play the music in the external player as usual. (Make sure the volume output level of the player

is in high level. Otherwise, sound from this unit is weak).

AUX IN 2 : LISTEN TO EXTERNAL AUDIO DEVICES

as the figure above.

INDICATO R

AUX IN 2

VOL- VOL+

TUNE-

TUNE+

POWER

SOURCE

Check the followings before requesting service

SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTION

desired mode.

Press the SOURCE button repeatedly to

set the input source to the desired mode

TROUBLESHOOTING GUIDE

No power

No sound

Sound distortion

Remote not

working

Bluetooth

reception failure

Have not paired

The external device is far from

the unit

The batterry

is consumed

Volume level too high

Bass level of the connected

device too high

Input source incorrect

The connected device is not

in payback mode

Volume in minimum position

The unit is in Standby mode

Connect the power AC/DC adapter

Press button to turn on the unit

Raise volume level by pressing the VOL

(Volume) + button

Play the music/movie in the connected

device as usual

and make sure the

volume level of it is in high level

Reduce the bass level of the connected

device

VOL (Volume ) - button

Reduce the volume level by pressing

the

Replace with new battery

Put the external BT device close to the

unit

Pair both units as BT pairing page

Power AC/DC adapter

not connected

Accessories

Remote Effective Range.............................................................................................Up to 15 feet

GENERAL SPECIFICATIONS

Power Source........................................................................................ DC 16V; 1.8A.

Radio Coverage................................................................................................FM 87.5 -108.0 MHz

Impedance of Speakers:

Loud Speakers .......................................................................................................

8 Ohm, 15W x 2

Tweeters...................................................................................................................

8 Ohm, 5W x 2

Bluetooth Effective Range in Open Aera......................................................................Up to 32 feet

1 x Remote Control, using CR 2025 button cell ( Included,already installed in remote control )

1 x Stereo Audio Connection Cable with 3.5mm stereo plugs

4 x Metallic Screws ( For Wall Mount )

1 x User's Manual

---

1 x AC/DC Adaptor ( Input: AC 100-240V~ ; 50/60Hz; 0.8A.

Output: DC 16V; 1.8A )

1 x RCA Connection Cable

1 x Plastic Base

4 x Plastic Inserts ( For Wall Mount )

2 x Metallic Brackets

2 x Plastic Brackets ( For Stand on Flat Surface )

---

Craig CHT915 Owner's manual

Craig CHT915 Owner's manual

Craig CHT915 Owner's manual

Related papers

Other documents