• Fitting Material: Plastic.
• Motor: 40W(F30W). 30W(F46W). Ball bearing motor.
• Voltage: 220V - 240V ~ 50/60Hz.
• Protection against electric shock: Class 2: Does not require earthing.
• IP Rating: Fitting - IP20. Motor - IPX4. Not for outdoor use
• Dimensions: F30: (D) 120mm X (Ø) 350mm.
F46: (D) 120mm X (Ø) 305mm.
• Cut Out : F30 : 300mm.
F46 : 245mm.
• Air Movement : (F30W) 360m3 / hr. , (F46W) 240m3 / hr.
SPECIFICATIONS ASSEMBLY INSTRUCTIONS
F30 / F46 - attachments:
If the external exible cable or cord of this luminaire is damaged, it should be exclusively replaced
by the manufacturer or his service agent or a similar qualied person in order to avoid a hazard.To
ensure that you get maximum longevity and maximum use out of your luminaire, please observe
the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire
must be carried out by a qualied electrician, in accordance with SANS 10142. On completion
of installation, ensure that the Certicate of Compliance is updated.
• Before connecting this luminaire, ensure that voltage indicated on the rating label corresponds
with the mains voltage in your home.
• When changing the lamp, ensure that the power is turned off.
• This luminaire is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons,
caused by the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a professional
electrician or your supplier for assistance.
• Ensure all items / components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, i.e. using silicon sealers or incorrect cabling, will invalidate your
warranty. If one is not supplied within the carton, DO NOT use a solid speed control.
• Each blade set supplied is weighted and a complete set.
• Please check whether the connection of the power cord is safe and reliable before installation.
• Always ensure that the mains supply voltage is correct.
• Do not use the fan outdoors.
• Do not insert objects or ngers through the bars of the grill.
• This appliance is not intended for use by young children or inrm persons unless they have been
adequately supervised by a responsible person.
• Always unplug the fan when cleaning or moving from one location to another.
• Always ensure that the fan is on an even, stable surface.
• To disconnect the appliance, unplug by rst turning off the mains power then unplugging the fan.
Do not pull on the cord.
IMPORTANT SAFEGUARDS
CLEANING
• Before cleaning always ensure the power supply is turned off and that the fan has
been unplugged.
• Do not immerse the fan in water.
• No abrasive products, solvents, detergent may be used to clean this fan.
• Ensure that the fan does not come in contact with corrosive chemicals, etc.
• Remove the front grill guard and wipe down parts with a damp cloth to remove any dust.
• Ensure all parts are dry before reassembling your fan.
• The motor bearings are permanently sealed and do not require additional lubrication.
Aside from blades, there are no user serviceable parts in this appliance.
Do not tamper with the fan motor, if repair is required, contact the dealer from whom you
purchased this appliance or contact Eurolux.
Check for any hidden timbers, wiring or water pipes in the cut-out area before installation.
Always ensure that the electricity is turned off before installing. A disconnecting device (isolator)
must be installed on the primary side of the ceiling extractor fan (not supplied).
In order for the warranty to be honoured, the fan must be installed:
1.1. At least 2.3m above the ground.
1.2. At least 90cm away from any hotplate and have at least 50cm clear space above the
fan blades.
1.3. Ensure the power cord will not make contact or obstruct the fan blades.
1.4. Ensure any ceiling insulation or frame does not obstruct airow to the fan.
1.5. Clean the grill and blades regularly
1.6. If ducting is required, it must be larger than the diameter of the fan blades.
Ducting that is longer than 1meter will affect the fans performance and void the warranty.
2. Cut a hole of (F30W - 300mm) or (F46W - 245mm) for the cut-out using either a
jigsaw, keyhole saw or hacksaw.
3. Remove the grill (pulls free of the frame) and connect the power to the outlet.
Insert the fan assembly into the opening.
A: Push the three bar clamps all the way out to hold the fan in the ceiling. Tighten screws
to secure into place. See diagram.
B: Remove the three bar clamps. Use wood screws (not supplied) to secure the fan to
the ceiling. Locate screws in the 3 holes in the outer lip of the fan frame.
Tighten Screw
Push in clamp
bars in 3 places
4. Place the grill over the fan assembly and push up until it snaps into place.
5. Precautions must be taken to avoid the back-ow of grease into the room from an open
ow of gas of any other open-re appliances.
1
2
DAEWOO ELECTRONICS KOC-1B0K0S User manual
Giacomini KHRA2-V User manual
Lucci Air 213130 Installation guide
Daewoo KOG-376T1S User manual
Fanaway 210665 Orbit DC Ceiling Fan User manual
V I V O FAN7291 User manual
DAEWOO ELECTRONICS KOR-630A1A User manual
LUCCI 018500 Installation guide
Daewoo KOC-910K0S01 User manual
Magic Chef MCD1110ST Owner's manual
