Walter Dialspeed Point Grinder - 6141 Owner's manual

Brand: Walter

Model: Dialspeed Point Grinder - 6141

Category: Edgers

Type: Owner's manual

This manual is also suitable for

Dialspeed Straight Grinder - 6145

DIALSPEEDTM

Straight grinders/Meuleuses droites

Model/Modèle 6141 E - For deburring applications/ Applications d’ébarbage

Model/Modèle 6145 E - For brushing and polishing applications/Applications

de brossage et de polissage

READ CAREFULLY BEFORE

USING THIS POWER TOOL

6141 E

6145 E

LIRE ATTENTIVEMENT

AVANT D’UTILISER CET

OUTIL ÉLECTRIQUE

3DialSpeedTM

CONTENTS

General safety rules ........................................ 4

Introduction ................................................12

Voltage .....................................................12

Extension cord ............................................ 13

Model illustration .......................................... 13

Side handle (6145 E) ...................................... 13

Switch ..................................................... 13

DialspeedTM selector ...................................... 14

DialspeedTM settings ...................................... 14

DynamaxTM electronics ................................... 14

Operation ................................................. 14

Mounting abrasives ....................................... 15

Carbon brushes ........................................... 15

Preventive maintenance .................................. 15

WALTER sales and service ............................... 16

Accessories ............................................... 16

Warranty policy ............................................ 17

Technical data ............................................. 17

WALTER programs and seminars ........................ 18

Version française .......................................... 19

60-C 760 04/13

4DialSpeedTM

GENERAL SAFETY RULES

Every WALTER power tool is produced in accordance with applicable

standards governing the manufacture, performance and safety of power

tools.

WARNING: Read all instructions. Failure to follow all

instructions listed below may result in electric shock, re and/

or serious injury.

The term “power tool” in all of the warnings listed below refers to the

Dialspeed straight grinders model 6141 and model 6145.

1) Work area

a) Keep work area clean and well lit. Cluttered and dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres, such

as in the presence of ammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power

tool. Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the

plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodied plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away from

heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

5DialSpeedTM

3) Personal safety

a) Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while

you are tired or under the inuence of drugs, alcohol or

medication. A moment of inattention while operating power tools

may result in serious personal injury.

b) Use safety equipment. Always wear eye protection. Safety

equipment such as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate conditions will reduce

personal injuries.

c) Avoid accidental starting. Ensure the switch is in the o-

position before plugging in. Carrying power tools with your

nger on the switch or plugging in power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep

your hair, clothing and gloves away from moving parts. Loose

clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction

and collection facilities, ensure these are connected and

properly used. Use of these devices can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on

and o. Any power tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

6DialSpeedTM

e) Maintain power tools. Check for misalignment or binding of

moving parts, breakage of parts and any other condition that

may aect the power tools operation. If damaged, have the

power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits etc. in

accordance with these instructions and in the manner

intended for the particular type of power tool, taking

into account the working conditions and the work to be

performed. Use of the power tool for operations different from

those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualied repair person using

only identical replacement parts. This will ensure that the safety of

the power tool is maintained.

6) Safety instructions for all operations

Safety Warnings Common for Deburring, Fitting, Wire Brushing,

Polishing or Abrasive Cutting-O Operations:

a) These power tools are intended to function as tting (6141 only),

deburring (6141 only), brushing (6145 only) abrasive cutting-o

(6145 only) or polishing tool (6145 only). Read all safety warnings,

instructions and specications provided with this power tool.

Failure to follow all instructions listed below may result in electric

shock, re and/or serious injury.

b) Operations such as brushing, polishing or cutting are not

recommended to be performed on the 6141. Operations such as

deburring and tting are not recommended to be performed on

the 6145. Operations for which the power tool was not designed may

create a hazard and cause personal injury.

c) Do not use accessories which are not specically designed

and recommended by the tool manufacturer. Just because the

accessory can be attached to your power tool, it does not assure

safe operation.

d) The rated speed of the accessory must be at least equal to the

maximum speed marked on the power tool. Accessories running

faster than their rated speed can break and y apart.

7DialSpeedTM

e) The outside diameter and the thickness of your accessory must

be within the capacity rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or controlled.

f) The arbour size of wheels, anges, backing pads or any other

accessory must properly t the spindle of the power tool.

Accessories with arbour holes that do not match the mounting

hardware of the power tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is dropped, inspect

for damage or install an undamaged accessory. After inspecting

and installing an accessory, position yourself and bystanders

away from the plane of the rotating accessory and run the

power tool at maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test time.

h) Wear personal protective equipment. Depending on application,

use face shield, safety goggles or safety glasses. As appropriate,

wear dust mask, hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping ying debris generated

by various operations. The dust mask or respirator must be capable

of ltrating particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal protective

equipment. Fragments of workpiece or of a broken accessory may

y away and cause injury beyond immediate area of operation.

j) Hold power tool by insulated gripping surfaces only when

performing as the accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and shock the operator.

k) Position the cord clear of the spinning accessory. If you lose

control, the cord may be cut or snagged and your hand or arm may

be pulled into the spinning accessory.

l) Never lay the power tool down until the accessory has come to

a complete stop. The spinning accessory may grab the surface and

pull the power tool out of your control.

m) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your

clothing, pulling the accessory into your body.

8DialSpeedTM

n) Regularly clean the power tool’s air vents. The motor’s fan will

draw the dust inside the housing and excessive accumulation of

powdered metal may cause electrical hazards.

o) Do not operate the power tool near ammable materials. Sparks

could ignite these materials.

p) Do not use accessories that require liquid coolants. Using water

or other liquid coolants may results in electrocution or shock.

7) Further safety instructions for all operations

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel,

backing pad, brush or any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction opposite of the

accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch point

can dig into the surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward or away from the

operator, depending on direction of the wheel’s movement at the point

of pinching. Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below.

a) Maintain a rm grip on the power tool and position your body

and arm to allow you to resist kickback forces. Always use

auxiliary handle, if provided, for maximum control over kickback

or torque reaction during start-up. The operator can control torque

reactions or kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating accessory. Accessory

may kickback over your hand.

c) Do not position your body in the area where power tool will

move if kickback occurs. Kickback will propel the tool in direction

opposite to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges etc. Avoid

bouncing and snagging the accessory. Corners, sharp edges or

bouncing have a tendency to snag the rotating accessory and cause

loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed saw

blade. Such blades create frequent kickback and loss of control.

9DialSpeedTM

8) Additional safety instructions for grinding and cutting-o

operations

Additional Safety Warnings Specic for Abrasive Cutting-O

Operations:

a) Use only wheel types that are recommended for your power tool

and the specic guard designed for the selected wheel. Wheels

for which the power tool was not designed cannot be adequately

guarded and are unsafe.

b) The guard must be securely attached to the power tool and

positioned for maximum safety, so the least amount of wheel is

exposed towards the operator. The guard helps to protect operator

from broken wheel fragments and accidental contact with wheel.

c) Wheels must be used only for recommended applications. For

example: do not grind with the side of cut-o wheel. Abrasive

cut-off wheels are intended for peripheral grinding, side forces

applied to these wheels may cause them to shatter.

d) Always use undamaged wheel anges that are of correct size

and shape for your selected wheel. Proper wheel anges support

the wheel thus reducing the possibility of wheel breakage. Flanges

for cut-off wheels may be different from grinding wheel anges.

e) Do not use worn down wheels from larger power tools. Wheel

intended for larger power tool is not suitable for the higher speed of a

smaller tool and may burst.

9) Additional safety instructions for cutting-o operations

Additional Safety Warnings Specic for Abrasive Cutting-O

Operations (6145 only):

a) Do not “jam” the cut-o wheel or apply excessive pressure. Do

not attempt to make an excessive depth of cut. Overstressing the

wheel increases the loading and susceptibility to twisting or binding of

the wheel in the cut and the possibility of kickback or wheel breakage.

b) Do not position your body in line with and behind the rotating

wheel. When the wheel, at the point of operation, is moving away

from your body, the possible kickback may propel the spinning wheel

and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any reason,

switch o the power tool and hold the power tool motionless

until the wheel comes to a complete stop. Never attempt to

remove the cut-o wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheel binding.

10 DialSpeedTM

d) Do not restart the cutting operation in the workpiece. Let the

wheel reach full speed and carefully reenter the cut. The wheel

may bind, walk up or kickback if the power tool is restarted in the

workpiece.

e) Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces tend to

sag under their own weight. Supports must be placed under the

workpiece near the ne of cut and near the edge of the workpiece on

both sides of the wheel.

f) Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that can cause kickback.

10) Additional safety instructions for polishing operations (Model

6145 only)

Safety Warning Specic for Polishing Operations (Model 6145 only):

a) Do not allow any loose parts or its attachment strings to spin

freely. Tuck away or trim any loose attachment strings. Loose

and spinning attachment strings can entangle your ngers or snag on

the workpiece.

11) Additional safety instructions for wire brushing operation (Model

6145 only)

Safety Warnings Specic for Wire Brushing Operations:

a) Be aware that wire bristles are thrown by the brush even during

ordinary operation. Do not overstress the wires by applying

excessive load to the brush. The wire bristles can easily penetrate

light clothing and/or skin.

b) If the use of a guard is recommend for wire brushing, do not

allow any interference of the wire wheel or brush with the guard.

Wire wheel or brush may expand in diameter due to work load and

centrifugal forces.

11DialSpeedTM

12) Addition:

a) Recommended diameter of accessories for the tool.

Flap wheel: Maximum 1- ½” (Model 6145 only)

Brushes: Maximum 3” (Model 6145 only)

b) Storage and handling of recommended accessories

Keep your power tool and accessories in a low humidity and

ambiant temperature at all time. This will prevent premature

breakage of your tool.

12 DialSpeedTM

INTRODUCTION

Your WALTER power tool is precision built to meet the highest industrial

standards. For maximum performance and longest tool life, follow the

operating instructions and service procedures outlined in this manual.

This tool is CSA certied for both Canada and USA.

This tool is double insulated, it may be safely operated from

a grounded or ungrounded receptacle. It is supplied with a

2-conductor power cord and a polarized plug (one blade wider

than the other). The plug will t only one way into a polarized

outlet. If the plug does not t, have the outlet replaced by a

qualied electrician. If an extension cord is necessary (See

table on page 4), use only one that is polarized. Do not change

the plug yourself in any way.

In order to maintain the safety features of the double insulation, the

motor housing must not be drilled to ax nameplates or the like. Self-

adhesive labels may be used for this purpose.

VOLTAGE

Before connecting the tool, check that the voltage shown on the rating

plate is the same as the power source. Operating the tool on a voltage

other than specied on its rating plate may result in personal injury to

the user and damage to the unit.

13DialSpeedTM

EXTENSION CORD

When an extension cord is required, use one that is appropriate for the

power demands of the tool.

Extension cords of inadequate wire size cause a serious drop in voltage,

loss of power and possible motor damage.

To limit line voltage drop to a safe level, refer to the following table:

Length in meters 8 15 23 30

Length in feet 25 50 75 100

Model 6141 E Wire size AWG 16 16 14 12

Model 6145 E Wire size AWG 16 16 14 12

Note: Extension cords used outdoors, must be approved for outdoor use.

SIDE HANDLE (6145 E)

Side handle (1) may be rotated to either side for greater convenience in

both right and left hand operation.

For reasons of safety and better control, the side handle must

always be used.

SWITCH

To start, push slide (2) forward locking it in the ON position. To stop,

press down on the back of the slide returning it to the OFF position.

14 DialSpeedTM

DIALSPEEDTM SELECTOR

Select the required speed by rotating speed selector (3). Positions 1-6

roughly equal the following no load revolutions per minute:

Pos. 1 2 3 4 5 6

6141 E 10,000 14,000 18,500 22,000 26,000 30,500

6145 E 2,500 4,000 5,500 7,000 8,000 8,700

Note amperage rating under TECHNICAL DATA.

DIALSPEEDTM SETTINGS

Set the Dialspeed to position 4 and adjust either up or down until you

have found a speed that meets your requirements. The correct setting

will depend on:

a) Type of material being worked.

b) Abrasive accessory being used.

c) Amount of pressure being applied.

d) Surface nish required.

DYNAMAXTM ELECTRONICS

The built-in electronic feedback circuit continuously monitors the load

on the motor and adjusts power as required to maintain a virtually

constant speed under moderate load.

OPERATION

Please be sure to read and observe the SAFETY INSTRUCTIONS at

the beginning of this manual.

Use only accessories that are suitable for these power tools and that

meet their minimum RPM requirements.

The use of any accessories other than those recommended may be

hazardous. Inspect accessories before using. Do not use any that

may be damaged.

For maximum performance and best eciency, apply a steady and

even pressure. Do not use excessive force. Always wear protective

equipment.

15DialSpeedTM

MOUNTING ABRASIVES

These tools are equipped with an exclusive spindle lock feature that

makes it fast and easy to change abrasive accessories.

1) To loosen collet, press and keep holding the locking spindle button

down (4). It may be necessary to turn the spindle for the spindle

to engage. Loosen collet nut by turning it counterclockwise with

supplied 19 mm open-end spanner.

2) Slip point shaft into collet making sure that the shaft size matches

the collet opening. The tools are supplied with a 1/4" collet.

3) Secure mounted point by screwing back on spindle and turning collet

nut clockwise. Tighten rmly.

4) Keep accessory shaft overhang to a minimum by slipping it into the

collet as far as possible.

CARBON BRUSHES

This tool is equipped with self-disconnecting carbon brushes. When the

brushes have reached their minimum length, they automatically interrupt

the current ow and the tool stops.

Use only genuine WALTER carbon brushes. These brushes are specially

made for these tools; they will maintain their high performance standard

and ensure maximum life of the motor.

When the carbon brushes require replacement, it is recommended that

the tool be sent to a WALTER Factory Service Center or a WALTER

Authorized Service Center. Apart from changing the brushes, your power

tool will be cleaned, inspected and lubricated as required. If new parts

are necessary, only genuine WALTER replacement parts will be used.

PREVENTIVE MAINTENANCE

Your WALTER power tool should be properly maintained to insure

continued high performance. Use low pressure compressed air to blow

out dust from the motor through the vent openings.

Clean dust and dirt deposits from the exterior of the tool. Clean the

power cord to prevent deterioration from oil and grease and check for

possible damage.

Note: Damaged cord sets must be replaced. Refer to the Spare Parts

List for the order number.

16 DialSpeedTM

WALTER SALES AND SERVICE

MONTREAL: 5977 Trans Canada Highway

Pointe Claire, QC H9R 1C1

Tel: 514 630-2801

Fax: 514 630-2825

TORONTO: 151 Superior Blvd., Unit 12

Mississauga, ON L5T 2L1

Tel: 905 795-8555

Fax: 905 795-8558

EDMONTON: 18527-104 Avenue N W

Edmonton, AB T5S 2V8

Tel: 780 451-2053

Fax: 780 453-1589

VANCOUVER: 1-1595 Cliveden Avenue West

Delta, BC V3M 6M2

Tel: 604 540-4777

Fax: 604 540-4778

For the location of an Authorized Service Center closest to you,

Call toll free 1 888 JWALTER (1 888 592-5837)

Visit us at our web site: walter.com

ACCESSORIES

- Metal carrying case, no. 30-B 010

- Flexible shaft with 1/4’’ collet, 5' long, no. 30-B 050

- 1/4’’ collet for exible shaft, no. 30-B 054

- 6 mm collet for exible shaft, no. 30-B 053

- Bench mount, no. 30-B 002

- 1/8’’ collet, no. 30-B 047

- 6 mm collet, no. 30-B 048

- 5/16’’ collet, no. 30-B 049

17DialSpeedTM

WARRANTY POLICY

All WALTER power tools and accessories are inspected and tested before

shipping and are warranted to be free from any defect in material and

faulty workmanship. Should any malfunction occur within one (1) year from

the date of original purchase, return the complete tool prepaid with a proof

of purchase to the nearest WALTER Factory or Authorized Service Center.

If an examination shows that the malfunction was caused by defective

material or faulty workmanship, WALTER will repair (or at our option,

replace) without charge. This warranty does not apply when normal

maintenance is required, repairs or replacements have been made or were

attempted by anyone other than WALTER Authorized Service personnel,

and does not cover any damage caused by accidents, modications,

use of improper accessories, abuse or misuse, which also includes

overloading the tool beyond its rated capacity as well as its continued use

after partial failure. No other warranty, written or verbal, is authorized.

In no event shall WALTER be liable for any indirect, incidental or

consequential damages from the sale of this tool. This disclaimer

applies both during and after the term of this warranty.

This warranty gives you specic rights. The provisions contained

in this warranty are not intended to limit, modify, take away from,

disclaim or exclude any warranties set forth in any Provincial

legislation. To the extent required by law, the provisions in

any Provincial or Federal legislation with respect to warranties

take precedence over the provisions in this warranty.

TECHNICAL DATA

MODEL 6141 E 6145 E

VOLTAGE: 120V AC, 60 Hz 120V AC, 60 Hz

AMPERAGE: 6.2 (Pos. 6) 7.5 (Pos. 6)

NO-LOAD RPM: 10,000 - 30,500 2,500 - 8,700

COLLET SIZE: 1/4” 1/4”

WEIGHT: 1.8 kg. - 4.0 lbs. 2.0 kg. - 4.4 lbs.

18 DialSpeedTM

Save time, reduce costs

and work safely!

SAFETY

SEMINARS

At Walter, safety is a

top priority. We want

to bring our product

knowledge and

know-how to you!

Our safety seminars

are Free!

Contact a Walter

Sales Representative

today!

BUCKET

PROGRAM

In an effort to save

costs, improve safety

and encourage

efﬁciency, Walter

offers you its Bucket

Program.

Ask your Walter

Sales Representative

for all the details.

PRODUCT

DEMONSTRATIONS

& TRAINING

Considering using

Walter products in the

future? Schedule a

product training with

us today.

Our product trainings

include (but are not

limited to): Combo Zip,

Bio-Circle, Enduro-Flex,

AF-Clean and

many others

ENVIRONMENTAL

SOLUTIONS

Bio-Circle

Environmental

Solutions reduces

waste and

operating costs,

while increasing

productivity.

more information.

Bio-Circle; Making

Green Work!

For product information or

a free demonstration at your facility,

call toll free 1 888 592-5837

or visit us at walter.com

19DialSpeedMC

TABLE DES MATIÈRES

Directives de sécurité ..................................... 20

Introduction ............................................... 28

Voltage .................................................... 28

Rallonge électrique ....................................... 29

Illustration du modèle ..................................... 29

Poignée latérale (6145 E) .................................. 29

Interrupteur ................................................ 29

Sélecteur de vitesse DialspeedMC ........................ 30

Réglage DialspeedMC ..................................... 30

Électronique DynamaxMC ................................. 30

Fonctionnement ........................................... 30

Montage d’accessoires ................................... 31

Balais de carbone ......................................... 31

Entretien préventif ......................................... 31

Vente et service WALTER ................................. 32

Accessoires ............................................... 32

Politique de garantie ...................................... 33

Informations techniques .................................. 33

Programmes et séminaires WALTER ..................... 34

20 DialSpeedMC

DIRECTIVES DE SÉCURITÉ

Tous les outils électriques WALTER sont fabriqués selon les normes

établies concernant la fabrication, le fonctionnement et la sécurité des

outils électriques.

AVERTISSEMENT: Lire tous les avertissements de sécurité

et toutes les instructions. Ne pas suivre les avertissements et

instructions peut donner lieu à un choc électrique, un incendie et/

ou une blessure sérieuse.

Le terme « outil » dans les avertissements fait référence aux meuleuses

droites Dialspeed, modèle 6141 et modèle 6145.

1) Sécurité de la zone de travail

a) Conserver la zone de travail propre et bien éclairée. Les zones en

désordre ou sombres sont propices aux accidents.

b) Ne pas faire fonctionner les outils électriques en atmosphère

explosive, par exemple en présence de liquides inammables,

de gaz ou de poussières. Les outils électriques produisent des

étincelles qui peuvent enammer les poussières ou les fumées.

c) Maintenir les enfants et les personnes présentes à l’écart

pendant l’utilisation de l’outil. Les distractions peuvent vous faire

perdre le contrôle de l’outil.

2) Sécurité électrique

a) Il faut que les ches de l’outil électrique soient adaptées

au socle. Ne jamais modier la che de quelques façons

que ce soit. Ne pas utiliser d’adaptateurs avec des outils à

branchement de terre. Des ches non modiées et des socles

adaptés réduiront le risque de choc électrique.

b) Éviter tout contact du corps avec des surfaces reliées à la

terre telles que les tuyaux, les radiateurs, les cuisinières et les

réfrigérateurs. Il existe un risque accru de choc électrique si votre

corps est relié à la terre.

c) Ne pas exposer les outils à la pluie ou à des conditions humides.

La pénétration d’eau à l’intérieur d’un outil augmentera le risque de

choc électrique.

d) Ne pas maltraiter le cordon. Ne jamais utiliser le cordon

pour porter, tirer ou débrancher l’outil. Maintenir le cordon à

l’écart de la chaleur, du lubriant, des arêtes ou des parties en

mouvement. Des cordons endommagés ou emmêlés augmentent le

risque de choc électrique.

e) Lorsqu’on utilise un outil à l’extérieur, utiliser un prolongateur

adapté à l’utilisation extérieure. L’utilisation d’un cordon adapté à

l’utilisateur extérieure réduit le risque de choc électrique.

Page is loading ...

Walter Dialspeed Point Grinder - 6141 Owner's manual

Brand: Walter

Model: Dialspeed Point Grinder - 6141

Category: Edgers

Type: Owner's manual

This manual is also suitable for

Dialspeed Straight Grinder - 6145

Download PDF

report

in other languages

français: Walter Dialspeed Point Grinder - 6141 Le manuel du propriétaire

Walter Dialspeed Point Grinder - 6141 Owner's manual

This manual is also suitable for

Walter Dialspeed Point Grinder - 6141 Owner's manual

in other languages

Related papers

Other documents