Intercoax IXAI-04 Owner's manual

Brand
Intercoax
Model
IXAI-04
Category
Digital Video Recorders (DVR)
Type
Owner's manual
1
Hardware Overview
Quick Start Guide
IXAI-04
Please read carefully the instruction manual before use. Depending on the model, the image and the actual look of the product may vary.
Rev.2.0© Intercoax Co., Ltd.
Applications
DC12V
HD MONITOR
MICRO SD
USB
IN1
IN2
GND
IN3
IN4
GND
D+
D-
NO
COM
NC
GND
IN
GND
OUT
GND
ALARM IN RS-485
RELAY AUDIO
DC12V
ETHERNET 1 USB
A monitor
to view live video
USB type storages
& extemal devices
IPCs
DVR/NVR RTSP Server
IPCs
(Dedicated LAN connection)
NVR / DVR
VMS system
Alarm monitoring system
Access control system
Cloud based web service
Relay
RS-485
Alarm-In
Access controller &
other alarming devices
Relay out
Alarm / Sensor dvices
1DC 12V Power Plug. Note, DC12V only
2ETHERNET1
RJ-45 Port for connecting internet and other
platforms such as interoperable VMS, recorders
and IP cameras.
3USB Universal Serial Bus(USB) Ports for additional
devices such as USB Mouse
4MICRO SD Allows a Micro SD card to be inserted.
5HD MONITOR
For connecting a monitor to view connected
cameras. Note, Inter AI cannot be configured
locally.
6ALARM IN Connector for alarm input
7RS-485
connector for RS-485 devices. T+ and T- pins
connect to R+ and R- pins of PTZ receiver
respectively.
8RELAY A Relay communication
9AUDIO Connect to mic & Speaker
qRESET Factory Default
wCLAMP HOLE DC Jack cable clamp fixed hole
DC12V
HD MONITOR
MICRO SD
USB
IN1
IN2
GND
IN3
IN4
GND
D+
D-
NO
COM
NC
GND
IN
GND
OUT
GND
ALARM IN RS-485
RELAY AUDIO
DC12V
ETHERNET1 USB
Front
Front
Back
Î
The DC power jack uses only one of the front and rear sides.
Unused DC jack holes are blocked by the accessory’s DC jack cover.
2
Network Connection Setting
Upon installation of Admin Tool, run the utility to configure network setting parameters
1. Discover Inter AI on the network through ‘Search’ button on the GUI.
2. Select Desired Inter AI Devices from the discovery results.
3. Network type can be configured ‘DHCP’ or ‘STATIC’. STATIC setting requires ‘IP Address’, ‘Subnet Mask’, and ‘DNS’ information manually
input according to the network environments. Please ‘Apply’ to complete the configuration process.
4. Network setting parameters refreshes after properly configured.
3
Inter AI connection
1. Open Web based Inter AI setting page by double clicking listed discovered devices.
Î
If a security warning message appears as shown below, please click the ‘Proceed to (unsafe)’ through clicking ‘advanced’ menu.
This secure warning message would be popped up due to using private certificates.
Î
Recommended web Browsers: Google chrome, Fire fox and IE edge.
2. ID and password are required to log in. ID : ADMIN (The capital letters). Password : 1234
Video Sources Connection
The Video source configuration
Inter AI is designed to analyze video clips from IP cameras and other RTSP devices. It is configuring to utilized URL from the sources. The rule set up.
4
Rules & AI Algorithm Setup
1. Please Select desired AI Algorithms using pulled down menu.
2. When properly configured, grid/box populates to indicate detected objects.
Please visit below website for more detailed information.
Web: http://www.intercoax.com Tel: +82. 31. 365. 3133~4
E-mail: [email protected] Fax: +82. 31. 365. 3135
This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference that may cause undesired
operation
Video Sources Connection
1. Connect to streaming devices based on ONVIF Discovery protocol.
Inter AI supports ONVIF to connect to receive video streams from LAN environments.
a. ‘Discovery’ button brings the popped-up menu for ONVIF Discovery.
b. The Discovery function shows ONVIF devices
of the LAN when Discovery is completed.
c. Enter appropriate credential to connect
and pull video streaming.
d. The discovered devices can be assigned to
‘CH’ with pulled down menu.
e. Selected devices URL will be automatically
filled in when pressing ‘Apply’ button.
2. Manual video source matching based on RTSP URL supported devices.
The Inter AI supports RTSP supported devices based on standards TCP and URL can be entered manually.
3. Connection completion
Upon successful connection, status shows ‘Connected’ in green. Make sure to enter correct credential.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Intercoax IXAI-04 Owner's manual

Brand
Intercoax
Model
IXAI-04
Category
Digital Video Recorders (DVR)
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents