8) Please point the controller to the direction of the adaptor to use the remote function..
9) Press "MODE" switch on adaptor to select 8 functions: Combination, In waves, Sequential,Slow glow,
Chasing/Flash, Slow Fade, Twinkle/Flash,Steady on.
LOW VOLTAGE 300 MULTI-
COLOURED CLUSTER LIGHTS
WITH REMOTE CONTROL
These instructions are for your safety. Please read through them thoroughly
before use and retain for future reference.
Before You Start
Installation instructions:
1) This light chain is suitable for INDOOR AND OUTDOOR USE.
2) The AC adaptor MUST be installed INDOORS away from weather.
3) Do not position or place near heaters of any other direct sources of heat.
4) This product is suitable for positioning on surfaces which have normal flammability,e.g.wood, plasterboard,
masonry. However this does not include highly flammable surfaces(e.g.polystyrene, textiles).
5) Always position cables and extension leads so that they will not be a hazard to the elderly, pets and children.
6) DO NOT position this light set where it may become covered by other items e.g.curtains, nets or bedding.
7) Ensure the unit is positioned so that you have enough cable to reach an indoor mains power socket.
Decide on an appropriate location for your product (see Installation instructions below).
●
●If you have any doubt about installing this product, consult a qualified electrician.
● Care must be taken to avoid damage the cable or fittings.
● If any part of light set or cable is damaged, the light set MUST be discarded.
● This product is for use as a decoration only. Not to be used by children as a toy. Keep out of reach of children.
● Do not position this light chain where it will be exposed to extreme wet weather or submerged in water.
● Always switch off this light set or unplug an adaptor if unattended.
● DO NOT overload power sockets or extension leads.
● DO NOT pierce the cable when securing in place, bend or stand on the light chain, as this will damage the
bulbs or wiring.
● Please refer to the packing or product rating label for product class, specifications and rating.
The light chain is suitable for INDOOR AND OUTDOOR USE.
Warning
●
This product is NOT designed for permanent or long term use.
The AC adaptor MUST be installed INDOORS away from weather.
The supplied adaptor is suitable for operation of LED Modules only.
Only operate this light chain with the supplied adaptor, Model No. JT-EL/FC 24V3.6W-BT3
●
●
●
●
●
●
Do not connect this light chain electrically to another light chain.
●
Do not connect this light chain to the power supply while it is in the packaging.
DO NOT attempt to replace the non-replaceable bulbs in this light chain.
● Never allow any part of the set to come into contact with a source of heat or flame.
LED Bulbs
This light set is constructed with non-replaceable bulbs. DO NOT attempt to replace any of the bulbs in the
light set.
Keycode: 42781578
This product can control different luminance of lamps and lanterns and
timing function through remote control the output mode of the power supply.
2 x AAA battery (batteries not included)
Note: when the remote control distance significantly shortened, may be out
of battery. Please replace new battery according to the back of the remote
control is shown.
WIRELESS REMOTE CONTROLLER
BUTTON
Remote control panel key functions
1 ON/OFF
2 TIMER
3 MODE
4 DIMMING
- ON/OFF, control the open and close of the power output.
- Timing, control the opening and closing of the power supply’s timing function.
- Press the timing button, the indicator of the corresponding button lights up.
- Close the timing function, the indicator of the corresponding button turn off.
- Dimming function control four kinds of luminous intensity of lamps and lanterns: 100%, 75%, 50%, 25%.
- Timing mode for 6 hours,18 hours.
- control the lights’ eight kinds of flashing ways
1: Cyclical mode: regular circulation from the second mode to
Press once, flashing way increasing from mode low to high, at the end to
Press once, the luminance increasing from low to high, at the end to 100%.
Press once, the luminance decreasing from high to low, at the end to 25%.
the mode 8. Press once, flashing way decreasing from mode high to low,
at the end to the mode 1.
seventh mode 2: In Waves
3: Sequential
4: SLO-GLO
5: Chasing/Flash
6: Slow Fade
7: Twinkle/Flash
8: Steady On
- MODE
- Battery installation by adult is required
- Never mix different types or old and new batteries
- Do not short circuit supply terminals or dispose of batteries in fire
- Remove batteries during long period or non-use
WARNING:
Button function
Mode 1 Mode 2 Mode 3 Mode 4
Mode 8 Mode 7 Mode 6 Mode 5
At the same time, product restarts timing function .
6 hours – turn on , 18 hours –turn off .
The BUTTON indicator light is on, means power have been in timing mode.
At this time ,press the BUTTON ,the power can control the flashing way according to the circulation
of the functions as follow :
The following is the respective state for 6 hours on and 18 hours off at timing mode. - ON/OFF,
control the open and close of the power output.
- Press the BUTTON, you can manually set the timing function and the flashing function.
1 Timing function : Long press BUTTON for 3 seconds , indicator light on ,
it means the power start timing mode:
A At the state of 6 hours on :
B At the state of 18 hours off:
Memory function
2 Manually set flashing function
At this time, press the BUTTON, the power can control the flashing way according to the circulation of
the functions as follow :
Press the BUTTON, power will be restored to the brightness of the lights
went out and restart timing.
At this time ,press the BUTTON ,the power can control the flashing way according to the circulation
of the functions as follow :
This power supply has the memory function, after restart and restore power, can recover the previous state
(including timing state and dimming state), but when the remote control switched on again, will cancel the
timing function and luminescence brightness as before.
Mode 1 Mode 2 Mode 3 Mode 4
Mode 5
Mode 8 Mode 7 Mode 6
Adaptor Manual
1. Please use the equipments according to the rated voltage and current.
2. Do not open the cover of the equipments.
3. For use with LED lighting equipment.
4. The input and output voltage should be checked before use to ensure correct use.
5. This is the Class II product, only for indoor use.
6. The product is not a toy, keep it where children can not reach.
7. The lamp controlgear does not rely upon the luminaire enclosure for protection against accidental
contact with live parts.
8. If applicable:an indication that the controlgear is suitable for operation with LED modules.
9. Do-not-cover classification
The power supply that can be used where normally flammable materials.including building insulation,
are or may be present, but cannot be abutted against any material and cannot be covered in normal.
Minimum clearance distance from the top and sides of the control gear to normally flammable building
element is 75mm; as shown in below picture, A=B=C=Min.75mm.
Model No.
JT-EL/FC24V3.6W-BT3
Input Rated
Voltage Frequency Current
220-240VAC 50-60Hz 0.20A Max
Output Rated
Voltage Power
24V AC 3.6W
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Tascam DA-98 User manual
-
monzana 107711 Assembly Instructions
-
Tascam RC-898 User manual
-
-
PIAGGIO X8 400 Euro 3 Service Station Manual
-
APRILIA SCARABEO 500 - 2008 Service Station Manual
-
Casio LK-130ES Owner's manual
-
Tascam DA-98HR User manual
-
Casio LK-125 Owner's manual
-
VESPA S 2012 Service Station Manual