GGM Gastro GKS330N Owner's manual
- Category
- Drink coolers
- Type
- Owner's manual
BEVERAGE COOLER
USER MANUAL
MODEL: GKS330N
MODEL: GKS630FNN
MODEL: GKS908N
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS.
2
TABLE OF CONTENTS
Important Safet
y
Instructions 3
Appliance Safety 3
Important Safe
g
uides 4
Parts and Features 5-7
Electrical Connection / Extension Cord / Surge Protector 8
Installation Instructions 9
Before Usin
g
Your Appliance 9
Installation of Your Appliance 9
Operating Your Appliance 10
ON/OFF Power 10
Setting the Temperature Control 10
Interior Light 10
Door Lock 11
Positive Seal Self Closing Door 11
Shelves 11
Care and Maintenance 12
Cleanin
g
the Bevera
g
e Cooler 12
Power Failure 12
Movin
g
Your Bevera
g
e Cooler 12
Ener
gy
Savin
g
Ti
p
s 12
Troubleshootin
g
Guide 13
Wiring Diagram 14
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire, electrical shock,
or injury when using your appliance, follow
these basic precautions:
Read all instructions before using the Beverage Cooler.
DANGER or WARNING: Risk of child entrapment.
Child entrapment and suffocation are not problems of the past. Junked or abandoned
appliances are still dangerous . . . even if they will “just sit in the garage a few days”.
Before you throw away your old Beverage Cooler: Take off the door. Leave the
shelves in place so that children may not easily climb inside.
Never allow children to operate, play with, or crawl inside the appliance.
Never clean appliance parts with flammable fluids. The fumes can create a fire
hazard or explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity
of this or any other appliance. The fumes can create a fire hazard or explosion.
-Save these instructions-
APPLIANCE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always
read and obey all safety messages.
This is the Safety Alert Symbol. This symbol alerts you to potential hazards that
can kill or injure you and others. All safety messages will follow the Safety
Alert Symbol and either the words “DANGER”, “WARNING” or “CAUTION”.
Danger means that failure to heed this
safety statement may result in severe
personal injury or death.
Warning means that failure to heed this
safety statement may result in extensive
product damage, serious personal injury, or
death.
Caution means that failure to heed this
safety statement may result in minor or
moderate personal injury, or property or
equipment damage.
All safety messages will alert you do what the potential hazard is, tell you how to reduce the chance of
injury, and let you know what can happen if the instructions are not followed.
4
IMPORTANT SAFEGUIDES
Before the appliance is used, it must be properly positioned and installed as
described in this manual, so read the manual carefully. To reduce the risk of fire,
electrical shock or injury when using the appliance, follow basic precaution,
including the following:
Plug into a grounded 2-round and 1 hole outlet, do not remove grounding prong, do not use an
adapter, and do not use an extension cord.
Replace all panels before operating.
It is recommended that a separate circuit, serving only your appliance be provided. Use
receptacles that cannot be turned off by a switch or pull chain.
Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or
explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance. The fumes can create a fire hazard or explosion.
Before proceeding with cleaning and maintenance operations, make sure the power line of the
unit is disconnected.
Do not connect or disconnect the electric plug when your hands are wet.
Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result
in electrical shock or death.
Do not attempt to repair or replace any part of your appliance unless it is specifically
recommended in this material. All other servicing should be referred to a qualified technician.
FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
Use two or more people to move and install appliance. Failure to do so can result in back or other
injury.
To ensure proper ventilation for your appliance, the front of the unit must be completely
unobstructed. Choose a well-ventilated area with temperatures above 60°F (16°C) and below
90°F (32°C). This unit must be installed in an area protected from the element, such as wind, rain,
water spray or drips.
The appliance should not be located next to ovens, grills or other sources of high heat.
The appliance must be installed with all electrical, water and drain connections in accordance with
state and local codes. A standard electrical supply (230 V AC only, 50 Hz), properly grounded in
accordance with the National Electrical Code and local codes and ordinances is required.
Do not kink or pinch the power supply cord of appliance.
The fuse (or circuit breaker) size should be 15 amperes.
It is important for the appliance to be leveled in order to work properly. You may need to make
several adjustments to level it.
Never allow children to operate, play with or crawl inside the appliance.
Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may
damage or discolor the interior.
Do not use this apparatus for other than its intended purpose.
5
PARTS & FEATURES
GKS330N
1 Temperature Control
2 Interior Fan
3 Shelves
(
Total 4
)
4 Front Grille
5 Rear Casters
6 Levelin
g
Le
g
s
7 To
p
Hin
g
e
8 Glass Door with Inte
g
rated Handle
9 Side LED Lighting
6
1Canop
y
2 Temperature Control
3 Shelves
(
Total 4
)
4 Side vertical LED Li
g
htin
g
5Glass Door with Aluminum alloy handle
6 Under Cover
7 Rear wheels
8 Universal brake wheel
7
1Canop
y
2 Temperature Control
3 Shelves
(
Total 4
)
4 Side vertical LED Li
g
htin
g
5Sliding door with Metal handle
6 Under Cover
7 Rear wheels
8 Universal brake wheel
8
ELECTRICAL CONNECTION
This appliance should be properly grounded for your safety. The power cord of this appliance is
equipped with a 2-round and 1-hole plug which mates with standard 2 round and 1 hole wall outlets to
minimize the possibility of electrical shock.
This appliance requires a standard 230 Volt AC ~/50Hz electrical ground outlet with 2-round and 1
hole. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is
properly grounded.
The cord should be secured behind the appliance and not left exposed or dangling to prevent
accidental injury.
The appliance should always be plugged into its own individual electrical outlet which has a voltage
rating that matches the rating label on the appliance. This provides the best performance and also
prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never
unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from
the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
When moving the appliance, be careful not to damage the power cord.
EXTENSION CORD
Because of potential safety hazards under certain conditions, it is strongly recommended that you do
not use an extension cord with this appliance.
SURGE PROTECTOR
Most electrical appliances use a series of electric control boards to operate. These boards are very
susceptible to power surges and could be damaged or destroyed.
If the appliance is going to be used in an area or if your city / country is prone to power surges /
outages; it is suggested that you use a power surge protector for all electrical devices / appliances
you use. The surge protector that you select must have a surge block high enough to protect the
appliance it is connected to. If you have any questions regarding the type and size of surge protector
needed contact a licensed electrician in your area.
Damages due to power surges are not considered a manufacturer covered defect and will void your
product warranty.
9
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR BEVERAGE COOLER
Remove the exterior and interior packing.
Check to be sure you have all of the following parts:
1 Instruction Manual
5 Beverage Shelves
2 Keys
Before connecting this appliance to the power source, let it stand upright for approximately 2
hours. This will reduce the possibility of a malfunction in the cooling system from handling
during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
INSTALLATION OF YOUR BEVERAGE COOLER
This appliance is designed to be for free standing installation only.
Place your Beverage Cooler on a floor that is strong enough to support it when it is fully
loaded.
Your Beverage Cooler is designed to either be free standing in a fixed position or moveable
using the casters located at the rear of the unit.
Locate the Beverage Cooler away from direct sunlight and sources of heat (stove, heater,
radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase
electrical consumption. Extreme cold ambient temperatures may also cause the unit not to
perform properly.
Avoid locating the unit in moist areas.
Plug the Beverage Cooler into an exclusive, properly installed-grounded wall outlet. Do not
under any circumstances cut or remove the third (ground) prong from the power cord.
10
OPERATING YOUR BEVERAGE COOLER
It is recommended you install the appliance in a place where the ambient temperature is between 22º
- 26ºC. If the ambient temperature is above or below recommended temperatures, the performance
of the unit may be affected. For example, placing your unit in extreme cold or hot conditions may
cause interior temperatures to fluctuate. The range of 2º-8ºC may not be reached.
Your Beverage Cooler is designed to operate with at a range of 2 – 8ºC.
Attention
This unit is equipped with a power delay system to protect the compressor in the event of a
power outage.
• This power delay system will delay the compressor start cycle for “3” three minutes
both at the first time the unit is plugged in and when there is a power outage.
• Once the unit is plugged in for the first time or power has been restored to the unit,
the compressor will start cycling after (3) three minutes of uninterrupted power
supply.
• Digital display, LED Lighting and temperature settings will work as normal and not
be affected.
ON/OFF POWER
Your unit is designed to turn ON as soon as the power cord has been plugged into an active electrical
outlet.
Setting the Temperature Control
Your unit has only one control for regulating the temperature in the compartment. The temperature
control is located on the upper left hand side of the compartment.
The range of the temperature control is from “2 ºC” to “8ºC”.
The first time you turn the unit on, press the set button more than 3S and then press the
“DOWN” button to set the temperature to “2ºC”.
After 24 to 48 hours, adjust the temperature control to the setting that best suits your needs; by
first pressing the Set button more than 3S, pressing the or buttons .
To turn the off the cooling system, unplug the unit from the electrical outlet.
NOTE:
Also, as cold air falls and warm air rises, there could be a slight temperature variance between
the top and bottom shelves.
STORAGE
Many bottles may differ in size and dimensions. As such the actual number of bottles you may be able
to store may vary.
IMPORTANT SAFEGUARDS
Do not store food in Beverage Center, as interior temperature may not get cool enough to prevent
spoilage.
As a natural result of condensation, in summer months or areas of high humidity, the glass door
may build up moisture on the outside. Just wipe it away.
11
INTERIOR LIGHT
You can turn the interior light on or off by pressing the “FN” button on the control panel located at the
upper left hand side of the compartment.
DOOR LOCK
Your unit is provided with a lock and key combination.
The keys are located inside the plastic bag that contains the User’s Guide.
Insert the key into the lock and turn it clockwise to unlock the door. To lock the door turn the key
counterclockwise making sure metal pin is engaged completely.
Remove the key and place it in a secure place for safekeeping.
POSITIVE SEAL SELF-CLOSING DOOR
For your convenience, your Beverage Cooler has been designed with a self-closing door mechanism
that will completely close the door and create a positive seal between the door gasket and the cooler.
SHELVES
To prevent damaging the door gasket, make sure to have the door all the way opened when pulling
shelves out of the rail compartment.
For easy access to the storage content, you can pull the shelves approximately 1/3 the way out of the
rail compartment, for your safety and convenience this unit was designed with two (2) safety stoppers
on each side of the shelf track to prevent shelves from falling.
When removing any of these shelves out of the rail compartment, you must first remove all items from
the shelves, then disassemble and remove both of the plastic stoppers by removing safety stoppers
on each side of the shelf.
12
CARE AND MAINTENANCE
CLEANING YOUR BEVERAGE COOLER
Unplug the appliance, and remove all items including shelves.
Wash the inside surfaces with a warm water and baking soda solution. The solution should be
about 2 tablespoons of baking soda to a quart of water.
Wash the shelves with a mild detergent solution.
Wring excess water out of the sponge or cloth when cleaning area of the controls, or any
electrical parts.
Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with
a clean soft cloth.
Do not use steel wool or steel brush on the stainless steel. These will contaminate the stainless
steel with steel particles and rusting may occur.
POWER FAILURE
Most power failures are corrected within a few hours and should not affect the temperature of
your appliance if you minimize the number of times the door is opened. If the power is going to be
off for a longer period of time, you need to take the proper steps to protect your contents.
MOVING YOUR BEVERAGE COOLER
Remove all items.
Securely tape down all loose items (shelves) inside your appliance.
Tape the door shut.
Be sure the appliance stays secure in the upright position during transportation. Also protect
outside of appliance with a blanket, or similar item.
ENERGY SAVING TIPS
The Beverage Cooler should be located in the coolest area of the room, away from heat
producing appliances, and out of the direct sunlight.
13
PROBLEMS WITH YOUR BEVERAGE COOLER?
You can solve many common Beverage Cooler problems easily, saving you the cost of a possible
service call. Try the suggestions below to see if you can solve the problem before calling the servicer.
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE
Beverage Cooler does not operate. Not plugged in.
The circuit breaker tripped or a blown fuse.
Compressor power delay is activated, this delays
the power or cycling of the compressor for (3)
three minutes after a power outage or the first
time the unit is plugged in.
Beverage Cooler is not cold enough. Check the temperature control, setting maybe too
high.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Turns on and off frequently. The room temperature is hotter than normal.
A large amount of contents has been added to
the Beverage Cooler.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work. Not plugged in.
The circuit breaker tripped or a blown fuse.
The li
g
ht button is “OFF”.
Vibrations. Check to assure that the Beverage Cooler is
level.
The Beverage Cooler seems to make too much
noise.
The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling
sounds caused by the flow of refrigerant in your
Beverage Cooler.
Contraction and expansion of the inside walls
may cause popping and crackling noises.
The Bevera
g
e Cooler is not level.
The door will not close properly. The door is misaligned.
The Beverage Cooler is not level.
The gasket is dirty.
The shelves are out of position.
14
WIRING DIAGRAM
GKS330N
SWITCH
GKS630FNN/908N/630FNN-B/908N-B
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
GGM Gastro GKS330N Owner's manual
- Category
- Drink coolers
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI