Kellfri 33-JM40 is a simple and flexible universal spreader with many applications. It can be used all year round for spreading fertilizer, salt, sand, and grass seeds. The spreader has a 12v electric motor, a rain cover, and an attachment for the ATV’s package holder. It has a 570 x 420 x 350 mm size, weighs 5.5 kg, and can hold a maximum load of 40 kg. The spreader plate has 1st and 4 st settings, allowing you to adjust the spread pattern and rate. The spreader is easy to use and maintain, and it comes with a one-year warranty.
Kellfri 33-JM40 is a simple and flexible universal spreader with many applications. It can be used all year round for spreading fertilizer, salt, sand, and grass seeds. The spreader has a 12v electric motor, a rain cover, and an attachment for the ATV’s package holder. It has a 570 x 420 x 350 mm size, weighs 5.5 kg, and can hold a maximum load of 40 kg. The spreader plate has 1st and 4 st settings, allowing you to adjust the spread pattern and rate. The spreader is easy to use and maintain, and it comes with a one-year warranty.
Read this manual carefully
before using the product!
Translated from the original
2019-04-26
33-JM40
SALT AND FERTILISER SPREADER ATV
TABLE OF CONTENTS
Introduction 3
Product information 3
Safety instructions 4
Product safety instructions 4
Incase of emergencies 5
Surroundings 5
Warning labels 5
Personal protection 6
Steps before use 6
Use 7
Setting your spreader 7
Transport and storing 8
Maintenance and service 8
Recycling 8
Spreading instruction 8
After use 8
Assembly instruction 9
Installation of the spreader 9
Exploded drawing 10
Parts description 11
Warranty and condition terms 12
Table of contents →
INTRODUCTION
Thank you for choosing a product from Kellfri AB. By following general safety information,
operating instructions and common sense, you will have many years of enjoyable use of the
product. Kellfris equipment and products are aimed to be use by active farmers with high
demands on functionality.
PRODUCT INFORMATION
Simple and exible universal spreader with many applications. Can be used all year round
for spreading fertilizer, salt and sand etc.. The machine is delivered with 12v electric motor,
rain cover and attachment for the ATV’s package holder. Note! some ATVs, the package carrier
must be adapted for the machine.
TECHNICAL DATA 33-JM40
L x W x H 570 x 420 x 350 mm
Weight 5,5 kg
Maximum load 40 kg
Power 12v electric motor
Spreader plate 1 st
Spreader blade 4 st
INTENDED USE:
The machine is intended for spreading fertilizer, sand and salt. Can also be used for spreading
eg. grass seeds.
Table of contents →
SAFETY INSTRUCTIONS
Before using the trailer, and for the safety of yourself and others, you must read the safety
instructions and operating instructions and understand their contents. Always make the safe-
ty instructions and the operating instructions easily accessible to users of the equipment or
product. It is a good idea to read the safety instructions from time to time, both for your own
safety and that of others. It is important that the user understands that common sense and
general caution are not built into the product, but must be supplied by the user.
If the operating instructions gets damaged or in any other way cannot be used, please contact
and order a new one from: Your retailer or download from manual.kellfri.co.uk
Do not use the equipment or product if you feel ill, tired or are under the inuence of alcohol.
Do not use the equipment or product if you are taking prescribed medication or drugs, or
suering from severe depression or mental illness. Always comply with general rules of the
road and applicable rules stipulated by the Animal Welfare Act. People under the age of 15 and
those suering from mental illness are not allowed to use the equipment.
Kellfri disclaim any responsibility for self-made modications, changes or alterations.
Warning!
The original design of the product must not, under any circumstances, be modified
without the approval of the manufacturer. Unauthorised modifications and/or accesso-
ries may cause life-threatening injuries or death to users and others.
PRODUCT SAFETY INSTRUCTIONS
Read through the tractor/ATV’s operating manual before starting work.
The product may only be use in the matter decribed in this instruction manual.
• Always check that the performance of the machine and vehicle to be use guarantees
safety and functionality.
• Never overload the containers maximum loading capacity
• Do not drive up slopes that are too steep to drive up.
• The danger zone is 5-15 metres depending on the material to be spread. Only the oper-
ator is allowed to be within the danger zone whilst the spreader is in use.
• Under no circumstances are any person allowed to stand underneathe suspended loads.
• Never put your hands or feet under the machine without rst stopping the machine
• Never leave the equipment with the ATV’s engine running. Turn o the engine and apply
the parking brake when you leave the machine unattended, even for a short while.
• Always disengage the machine before performing service or maintenance work.
• Only the operator may be in the vicinity of the machine during all work.
• Never allow anyone to ride on the ATV during work
• Make sure all guards are tted and can not come loose.
• Fill the spreader tank directly on the eld. The container of the spreader could be dam-
aged if the machine is transported with a loaded container
• Max imum driving speed 20km/h
• Only 1 person is allowed to handle the machine whilst it’s runnig, misunderstanding dur-
ing work can lead to accidents and injuries.
Table of contents →
INCASE OF EMERGENCIES
In case of an emergency please dial 112.
Keep cell phone or emergency phone available specially when working alone. First aid kit and
re extinguishers must be kept easily accessible during all work, maintenance and service.
SURROUNDINGS
Make sure your working area is clear from people, children and objects before connecting
and using the machine. Risk of serious injuries during operation. Take an extra caution when
children are in the area where the equipment/ product is being use or stored. Check the area
for low hanging electrical wires. Be careful when working on slopes and near ditches.
Always work alone with single - purpose tools/products. Never have debris lying in your area.
Keep working areas clean. Always respect the risk zone.
Warning!
Children in the area should be supervised.
Under no circumstances should young children be allowed to work with this
equipment.
WARNING LABELS
Make sure that the warning labels are always visible, clean the warning labels if necessary. Do
not wash with high pressure washer directly on the warning label. If any part of the decal is
worn or label becomes frayed or otherwise unreadable, order new decals.
Symbol Explanation
Read the instruction manual! Before starting the operation
Warning! Before maintenance, service, connection and discon-
nection of the machine the ATV should be switched o and the
ignition key removed.
Warning for thrown objects!
Danger zone 5-15 m. No one other than the operator is al-
lowed in the vicinity of the machine during operation!
Warning! Rotating knives!
Risk of crushing!
Warning! Risk of Child Accident!
Children are not allowed to be anywhere near machine.
The product is CE-marked
Table of contents →
PERSONAL PROTECTION
Always use suitable protection equipment. Do not wear loose cloth-
ing or jewellery while working with the equipment. Long hair should
be tied up when working with machine that has moving parts. Use
protective gloves as there is a risk of burns if any hot surfaces are
touched.
STEPS BEFORE USE
Read the safety instructions and the operating instructions carefully. Make sure that you un-
derstand the safety instructions, operating instructions and warning decals. Use common
sense when using the product and suitable personal protective equipment. Always check the
performance of the machine combination to be used. It is important that these work in har-
mony. Ensure the equipment or product work as expected, and to guarantee the your safety
and others. Carry out a visual inspection of the equipment or product before use. Repair or
replace damaged or worn parts to reduce the risk of injury.
Grease moving parts and check that all nuts and bolts are tightened. Rectify if necessary.
Learn and remember the correct working method. Beginners must work slowly until they have
learned how the machine or product works. Users/customers are responsible for ensuring us-
ers can handle the situation. If users feel that the equipment is dangerous to use, it should not
be used.
• Perform a safety check of the machine before each use. If you notice any errors or wear,
the equipment should immediately be repaired.
• Make sure there are no foreign objects is stuck inside of the container before using it.
• Check the work area before operation. Make sure there are no people or animals nearby.
• Be sure that the machine is properly mounted and in good condition.
• Know your controls and how to stop tractor/ATV and equipment quickly in an emer-
gency.
• Connect the machine to the ATV. On some ATV , the package holder needs to be adapted,
this is done by the customer
• Mount the ow control unit where you reach it without any problem, secure with the
wing nut
• Install the electric motor controls in an appropriate location
Table of contents →
USE
Only people who understand the safety information and instructions in this manual may op-
erate the equipment. Be alert and careful when working with the machine and only use the
equipment or product in the manner described in this manual.
When working with equipment that has moving parts, there is always the risk for injury. Al-
ways work alone with the equipments that are dened as single porpose equipments.
Never overload the machine. Respect the equipment’s danger zone.
Make sure you know the distribution capacity of your machine and the material to be used.
Test drive on the eld to be sure that the spread will be right aligned. To much spread can dam-
age the crop and ungenerous distribution may not produce the desired results.
• Reduce speed when working on slopes and uneven terrain.
• Make sure that no foreign objects is in the fertilizer/salt or sand to be spread.
• Follow the guidelines that the ATV manufacturer provides regarding towing / pulling of
equipment / utensils.
• Do not ll the spreader container when you are transporting the equipment on longer
distance. Because the contents can get packed and aects and damaged the spreader
plate and aect the ability to spread.
• Be extremely careful if you spread herbicides when there is a risk if uncontrolled spread-
ing happens because of strong wind can lead to damaging the vegetation outside the
area. Always follow the instructions for the chemicals you use.
• If there would be a stop in the spreader plate inside the container: stop the machine,
make sure all moving parts have stopped, and open the feeder cover completely. By put-
ing a stick in the feeder you should be able to remove the object. WARNING! Risk of
crushing!
SETTING YOUR SPREADER
• The opening in the bottom of the spreader containers is adjusted with the control lever.
• The size of the opening depends on the calibration scale. Put the lever in the desired
position.
• For proper distribution calibrate your towing vehicle to run at the desired speed.
• Close the feeder cover and ll the container of tha material to be spread. Run a test drive
and make sure you gets the desired results. Make adjustments if necessary.
The spreading amount is determined with regards to:
• The kind of fertilizer that will be spread
• Working width [m]
• Working speed [km / h]
• The desired spread rate [kg / ha].
Various factors such as wind, fertilizer humidity, etc. can aect the ability to spread.
Table of contents →
SPREADING INSTRUCTION
If speed settings are not available, use the following procedure to calculate the setting.
• Determine how much material should be spread per 100m ²
• Measure a distance of 15 meters and mark, preferably on a paved surface such as a park-
ing space.
• Weigh enough of the material to be spread, ll the container at least half full. Note: Record
the weight for future use.
• When the unit is mounted on the vehicle and the container is lled (at least half full) with
material to be spread; position the vehicle far enough before the start of the test area so
that the vehicle reaches the desired speed before reaching the starting line.
• Set the stop in the measurement scale to a position you feel would be a suitable setting.
• Start the vehicle, drive forward and when you pass the starting line move the lever to
the open position. Important! Be aware of what is happening around you while driving.
• Continue driving until you reach the nish line, move the lever to the closed position.
• Stop the vehicle and note the width of the spread you just nished.
• Return to the starting point and empty the remaining material from the container and
weigh again.
• Adjust the stop on the measuring scale depending on whether you want more or less
spread.
AFTER USE
Rinse the machine with water and let it dry completely before storing it.
TRANSPORT AND STORING
Make sure that the area is free from persons, children and objects before transporting the prod-
uct. Always be extra cautious during transport. Ensure that the product is well anchored and
the existing transport locking device is mounted (if there is any). Always place the load as low
as possible. All cargo that sticks out should be rmly securely anchored. Respect the danger
zones even during transport. When lifting, no one is allowed to stand underneath any suspend-
ed load. Trailer used for transport should have functioning brakes. When traveling on a public
road, the SMV sign must be axed. Always keep the product in a dry place, preferably under
cover when not in use. Make sure that equipment is stationary and does not run the risk of
overturning. Never allow children to play at the storage area. Keep in mind the risk of tipping!
MAINTENANCE AND SERVICE
Ensure that the unit is stable and cannot tip over during maintenance and service. Replace
damaged or worn parts immediately to reduce the risk of abrasion. Always perform mainte-
nance, service and inspection, as recommended. Use only original replacement parts or spare
parts with equivalent performance to reduce the risk of damage.
ERROR CAUSE MEASURE
No materilas comes out of the
spreader or the spreading is
uneven
Packed fertilizer inside the container or
stuced in the spreading plate or blades
The opening is not completely open.
Check the material inside the container, clean
and take away stucked material.
Warning! Risk of injuries! Never touch rotating
part
RECYCLING
When disposing the product, this must be disassembled and
transported to the intended location of the municipality.
Contact your municipality for further information.
Table of contents →
ERROR CAUSE MEASURE
No materilas comes out of the
spreader or the spreading is
uneven
Packed fertilizer inside the container or
stuced in the spreading plate or blades
The opening is not completely open.
Check the material inside the container, clean
and take away stucked material.
Warning! Risk of injuries! Never touch rotating
part
1x cover 2x attachement for the ATV
WARNING! Before each use, check that the
spreader is securely attached to the vehicle.
Check all bolts and tighten if necessary.
1x container
8x J-bolt 4x metal palte 8x Nut M6 4x Screw M5x35
ASSEMBLY INSTRUCTION
1. Check that all parts are undamaged, check that all parts needed for installation are included.
2. If any parts are missing, the machine must not be used until they have been replaced.
Mount the attachement on the container as
shown in the picture and secure using the 4
screws.
Mount the feeding ow unit on the frame left
or right depending on where you attach the
spreader. Install it where you can reach it easily
INSTALLATION OF THE SPREADER
Position the spreader (in the middle) in the
front or in the back of the ATV’s package holder.
Attach the brackets on to the outermost rail
of the package holder using J-bolts and metal
plates. Tighten all bolts and make sure the
spreader cannot loosen during driving. Cut any
bolts that are too long and protruding. Grind/
sand sharp edges.
Parts:
Table of contents →
Pos. Description Qty
1Cover 1
2 Lid cover - electric motor 1
3 Electric motor 1
4 Guard for the motor 1
5 Cable ties 1
6 Lock nut M6 2
7 Motor bracket 1
8 Container 1
9 Washer Ø6 4
10 Bolt M6x16 2
11 Cable clamp 1
12 Fixing plate 1
13 Rivet Ø5x12 4
14 Screw M5x35 4
15 Spacers 1
16 Spreader plate 1
17 Adjusting plate 1
18 Screw M4x20 1
19 Screw M6x45 1
20 Round head bolt M6x25 1
Pos. Description Qty
21 Frame 2
22 Setting plate 1
23 Spacers 1
24 Wing nut M6 2
25 Lever 1
26 Lock washer Ø5 2
27 Bolt M5x6 2
28 Wire 1
29 Bolt M6x16 2
30 Lock washer Ø6 2
31 Cable 1
32 Nut M6 8
33 Metal plate 4
34 J-bolt 8
35 Bolt M5x12 2
36 Attachment for the wire 2
37 Lock nut M5 4
38 Washer Ø5 4
39 R-pin 1
PARTS DESCRIPTION
WARRANTY TERMS AND CONDITIONS
Validity of the warranty - Kelifri’s Warranty is valid 12 months from the date of purchase.
This warranty replaces - Compensation for spare parts after acknowledgment that the
fault lies on the material or manufacturing defects.
This guarantee do not
cover
• Labour costs
• Travel expenses
• Any modification that the buyer himself has/had made.
• Any consequential damages that occurred due to damage to the machine.
• Damage due to normal deterioration of the machine, inadequate: service,
user inexperience or use of spare parts which are not original.
• Wear parts such as hoses, seals, oils, and mechanical belts
CUSTOMER SERVICE
You are always welcome to give your feedbacks, reviews or ask us about our equipment and products.
Kellfri AB is constantly working on further developing their products and therefore reserves the right to
modify, among other things the design and appearance without further notice.
KELLFRI AB
Phone no: +46 (0)511 - 242 50
Fax: +46 (0)511 - 168 33
E-post: [email protected]
Kjell Johansson
Product Development Manager
2019-04-26
According to 2006/42/EC, Annex 2A
Kellfri AB
Munkatorpsgatan 6
532 37 Skara, Sweden
Declares that the machine
Name: 33-JM40
Type: Salt and fertiliser spreader 40 kg ATV
Complies with all applicable provisions of the Machinery Directive 2006/42/EC.
Other equipment must meet the hardware requirements of the Directive.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Kellfri 33-JM40 is a simple and flexible universal spreader with many applications. It can be used all year round for spreading fertilizer, salt, sand, and grass seeds. The spreader has a 12v electric motor, a rain cover, and an attachment for the ATV’s package holder. It has a 570 x 420 x 350 mm size, weighs 5.5 kg, and can hold a maximum load of 40 kg. The spreader plate has 1st and 4 st settings, allowing you to adjust the spread pattern and rate. The spreader is easy to use and maintain, and it comes with a one-year warranty.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Kellfri 33-JMATV Owner's manual
-
Kellfri 27-V18ATV Owner's manual
-
Kellfri 16-PGF2000 Owner's manual
-
Kellfri 21-KGR21 Owner's manual
-
Kellfri 23-DATV Owner's manual
-
Kellfri 28-V+ Owner's manual
-
Kellfri 28-VBS+ Owner's manual
-
Kellfri 35-HKK Owner's manual
-
Kellfri 33-JM650 Owner's manual
-
Kellfri 27-DC Owner's manual
Other documents
-
Rauch AXIS M 30.2 / 40.2 Operating instructions
-
Logic LDS360 User manual
-
-
TOPMAQ 12V ATV 80LB User manual
-
-
-
King Kutter S-ATV-180-U User manual
-
Worksaver ATVK-350 User manual
-
Land Pride DH15 User manual
-
FIELD TUFF FTF-350TST Owner's manual
