Classic Exhibits SYK-2029 Setup Instructions
- Type
- Setup Instructions
© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
20’
Perspective View
SYK-2029 - 10’ x 20’ Portable Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
REV 6/2023
© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq ft
Plan View
© 2022
Order #XXXXX
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, keep all
knobs & connectors attached to
extrusions during disassembly.
Part Identification - Numbering
7A
Engaged Lock
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
WARNING
General Information
© 2022
Order #XXXXX
TSP49 Profile
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Corner
Connector Corner
Connector
Corner
Connector
Corner
Connector
COMPLETED ASSEMBLY
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
Straight Connection
3) Tighten all knobs to secure connection.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
Slide connector across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
Straight Connector
2) Loosen all knobs, then slide straight
connector across the seam of extrusions.
Tool-less Frame Assembly
© 2022
Order #XXXXX
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
Tool-less Lightbox Frame Assembly
© 2022
Case 1 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3
13
13
Workstation
Graphics
(Qty. 2)
Level 4
8910 6
11 12
2,4
1 3
5,7
Counter
Legs
Case Packing
© 2022
Case 2 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Graphics
Setup Hardware
Level 1
(Bottom level)
Level 2 Level 3
Graphics
1
9
2 3
5 6 78
4
Level 4
Counter
Legs
Case Packing
© 2022
Case 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Graphics
Setup Hardware
Level 1
(Bottom level)
Level 2 Level 3
Setup Hardware
1 2 3
5 6 78
4
Level 4
Counter
Top
Counter
Top
9
Case Packing
© 2022
Case 4 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4
Counter
Top
Floor
Shelf
Middle
Leg
Legs
Counter
Graphic
Monitor
Mount
Monitor
Mount
Lights
Case Packing
© 2022
Step 1 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Connection Lock
w/ Knob
*
BACK VIEW
Knobs face back of assembly.
Tool-less Spline Connector
1. Place extrusions end-to-end.
2. Slide tool-less connectors
across seam of extrusions.
*
3. Tighten all knobs to secure connection.
Tool-less Corner Connector
1. Slide extrusion onto
Corner Connector.
2. Tighten all knobs to
secure connection.
*
Keep corner connectors attached to horizontal extrusions.
Assemble frame flat on ground. *
*
1
2
3
4
8
10
9
12
11
5
6
7
FRONT VIEW
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
45”h TSP49 Vertical Extrusion
31.305”h TSP49 Vertical Extrusion
45”h TSP49 Vertical Extrusion
31.305”h TSP49 Vertical Extrusion
36.467”w TSP49 Horizontal Extrusion
36.467”w TSP49 Horizontal Extrusion
36.467”w TSP49 Horizontal Extrusion
38.019”w TSP49 curved Horizontal Extrusion
38.019”w TSP49 curved Horizontal Extrusion
38.019”w TSP49 curved Horizontal Extrusion
45.209”h Z45 Vertical Extrusion
41.209”h Z45 Vertical Extrusion
6” x 22” Base Plate w/ flange (left)
6” x 22” Base Plate w/ flange (right)
Steps:
Refer to the Tool-less Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4], [11-12] & horizontals [5-6-7], [8-9-10]
together, using Tool-less Spline connectors labeled [X] & [Y].
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6/7], [8/9/10], using Tool-less Corner Connectors labeled [A] & [B].
3) Install Base Plates [13] & [14] to bottom corners of frame assembly
as shown. See Base Plate Attachment detail.
4) Lift frame to upright position, then connect vertical assembly [11/12] between
horizontal assemblies [5/6/7], [8/9/10] using Connection Lock w/ Knob.
**
13
14
Base Plate Attachment
*
bolt
knob
Front
key hole
1) Place key hole over bolt
on panel & slide down.
2) Twist knob to secure
connection.
threaded
hole
Base Plate
TOP VIEW
Left Base Plate
TOP VIEW
Right Base Plate
*
Y
*
X
*
Y
B
*
A
*
B*
A
*
*
X
*X
*X
*
X
Curved
connector
Arch corner
connector
Arch corner
connector
Curved
connector
Middle Backwall Frame Assembly
© 2022
Step 2 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Assemble frame flat on ground.
Steps:
Refer to the Tool-less Lightbox Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4] & horizontal
extrusions [5-6], [7-8] together, using Tool-less Spline connectors labeled [A].
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].
3) Install Base Plate [9] to bottom corner of frame assembly
as shown. See Base Plate Attachment detail.
4) Connect power cords to Supernova lights, as shown.
1
2
3
4
56
7
8
9
FRONT VIEW
A
*
A
*
A
*
A*
A
*
*
A
*A
*
A
CEI-110 Straight Connection
1. Place extrusions end-to-end.
2. Slide connectors
across seam of
extrusions.
*
3. Tighten all knobs to
secure connection.
CEI-110 Corner Connection
*1. Slide extrusion onto
corner connectors.
2. Tighten all knobs to
secure connection.
*
Item
1
2
3
4
5
6
7
8
9
Qty.
1
1
1
1
1
1
1
1
1
Description
45”h CEI110 Vertical Extrusion
45”h CEI110 Vertical Extrusion
45”h CEI110 Vertical Extrusion
45”h CEI110 Vertical Extrusion
27.35”w CEI110 Horizontal Extrusion
27.35”w CEI110 Horizontal Extrusion
27.35”w CEI110 Horizontal Extrusion
27.35”w CEI110 Horizontal Extrusion
6” x 22” End Base Plate w/ foot
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
++
--
Lights Male
Light to Light Attachment
Maximum of 7 lights per chain / 11 lights per Transformer
Light to Transformer Attachment
Transformer
Transformer
1) Place key hole over bolt on panel
& slide down.
2) Twist knob to secure connection.
Base Plate Attachment
*
bolt
knob
Base Plate
threaded
hole
key hole
Power
Break
Power
Break
Left Backwall Frame Assembly
© 2022
Step 3 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Assemble frame flat on ground.
Steps:
Refer to the Tool-less Lightbox Frame Assembly general information page.
1) Assemble vertical extrusions [1-2], [3-4] & horizontal
extrusions [5-6], [7-8] together, using Tool-less Spline connectors labeled [A].
2) Connect vertical assemblies [1/2], [3/4] between horizontal
assemblies [5/6], [7/8], using Tool-less Corner Connectors labeled [A].
3) Install Base Plate [9] to bottom corner of frame assembly
as shown. See Base Plate Attachment detail.
4) Connect power cords to Supernova lights, as shown.
Item
1
2
3
4
5
6
7
8
9
Qty.
1
1
1
1
1
1
1
1
1
Description
45”h CEI110 Vertical Extrusion
45”h CEI110 Vertical Extrusion
45”h CEI110 Vertical Extrusion
45”h CEI110 Vertical Extrusion
27.35”w CEI110 Horizontal Extrusion
27.35”w CEI110 Horizontal Extrusion
27.35”w CEI110 Horizontal Extrusion
27.35”w CEI110 Horizontal Extrusion
6” x 22” End Base Plate w/ foot
CEI-110 Straight Connection
1. Place extrusions end-to-end.
2. Slide connectors
across seam of
extrusions.
*
3. Tighten all knobs to
secure connection.
CEI-110 Corner Connection
*1. Slide extrusion onto
corner connectors.
2. Tighten all knobs to
secure connection.
3
4
1
2
65
8
7
9
FRONT VIEW
A
*
A
*
A
*
A*
A
*
*
A
*A
*
A
*
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
++
--
Lights Male
Light to Light Attachment
Maximum of 7 lights per chain / 11 lights per Transformer
Light to Transformer Attachment
Transformer
Transformer
1) Place key hole over bolt on panel
& slide down.
2) Twist knob to secure connection.
Base Plate Attachment
*
bolt
knob
Base Plate
threaded
hole
key hole
Power
Break
Power
Break
Right Backwall Frame Assembly
© 2022
Step 4 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
*
Left Frame
Right Frame
Steps:
1) Connect vertical of Left Frame Assembly to
Base Plate of Middle Frame Assembly.
See Base Plate Attachment detail.
2) Attach vertical of Right Frame Assembly to
Base Plate of Middle Frame Assembly.
See Base Plate Connection detail.
When assembled
FRONT VIEW
1
2
3
4
3
4
3
4
*
TOP VIEW
Left Base Plate
TOP VIEW
Right Base Plate
Base Plate Attachment
*
Place key hole over bolt on panel & slide down.
Twist knob to secure connection.
Front
Base Plate
key hole
bolt
Backwall Frames Connection
© 2022
Step 5 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
S
E
G
Grap
h
ic
Steps:
1) Apply SEG Graphics to assembled frames.
2) Apply SEG Blockers to back of left & right lightboxes.
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner, then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
FRONT VIEW
S
E
G
Grap
h
ic
SEG Blocker
SEG Blocker
S
E
G
Grap
h
ic
Fabric Graphics Application
© 2022
Step 6 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Attach clamp of
stem light to top of
horizontal extrusion
where desired.
Twist knob on back
to tighten in place.
Light Attachment
*
knob
Light
BACK VIEW
Light
*
Light
*
Workstation *
Workstation *
Extrusion
Hook the Mounting Bracket
over the vertical extrusion.
Slide
Bracket
forward
Slide down onto
V4 connector
Tighten knobs
to secure.
Mounting
Bracket
Workstation Bracket Attachment
Slide bracket forward, then
down onto V4 connector.
Tighten thumb screws to
secure connection to inside
of frame.
Bracket
TOP VIEW SIDE VIEW
123
V4
V4 connectors stay permanently
attached to vertical extrusion.
*
Threaded
Studs
Wing
nuts
Counter Top
Mounting
Bracket
Counter
Legs
UNDERSIDE VIEW
3) Attach power cords to
wireless chargers.
2) Connect Counter Top to
Mounting Bracket, using
wing nuts.
1) Attach threaded studs on underside
of Counter Top to Counter Legs;
secure with wing nuts.
Workstation Assembly
Keep cords attached to
underside of counter top.
Underside View of Counter
To Power
USB
charging
pad
power
cords
charging
block
Counter Top
Steps:
1) Attach Workstation Mounting Bracket
to backwall vertical as shown.
See Workstation Bracket Attachment detail.
2) Assemble Workstation legs & counter top to
bracket. See Workstation Assembly detail.
3) Affix Graphics to front of workstation assemblies,
using Velcro.
4) Attach Lights to top of backwall as shown.
See Light Attachment detail.
Graphic
Graphic
Backwall Attachments
© 2022
Step 7 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Assembly
Steps:
1) Attach Monitor Mounts to backwall verticals as shown.
See Monitor Mount Bracket Attachment detail.
Monitor
Mount
Monitor
Mount *
Extrusion
Slide
Bracket
forward
Mounting
Bracket
Monitor Mount Attachment
*Hook the Mounting Bracket
over the vertical extrusion.
Slide down onto
V4 connector
Tighten knobs
to secure.
Slide bracket forward, then
down onto V4 connector.
Tighten thumb screws to
secure connection to inside
of frame.
Bracket
Bracket
Monitor
Mount
back piece
TOP VIEW
SIDE VIEW
12
3Attach Monitor
Mount back piece
to Bracket.
4
5
V4
V4 connectors stay permanently
attached to vertical extrusion.
Slide monitor
mount into
back piece.
Backwall Attachments (cont’d)
© 2022
Step 8 of 8
Order #XXXXX
Locked layer contains
placeholder marks.
Upper Legs
Assemble unit upside-down.
Item
--
--
--
--
--
--
Qty.
2
2
1
1
1
1
Description
17.25”h aluminum Leg (lower)
18.5”h aluminum Leg (upper)
36.5”h aluminum Leg (middle)
43”w x 21.5”d Counter Base
17.95”w x 17.92”d Counter Shelf
43”w x 21.5”d Counter Top
Steps:
Note: Assemble counter upside-down.
1) Attach upper legs to underside of Counter Top. Twist to tighten.
2) Connect lower Legs through Counter Shelf to upper Legs, as shown.
3) Attach middle leg to underside of Counter Top. Twist to tighten.
Note: Holes for standoff graphic should face front of assembly.
4) Place Counter Base over lower & middle Legs & secure with screw caps.
5) Turn counter unit over & attach Graphic to middle leg, using Clamps w/ Velcro.
When assembled
Counter Top
Shelf
Counter Base
screw
caps
Lower Legs
Middle Leg
Clamp
w/ Velcro
Clamp
Clamp
w/ Velcro
Graphic
Clamp
w/ Velcro
*
*
*
Velcro
SYM-404 Counter Assembly
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Classic Exhibits SYK-2029 Setup Instructions
- Type
- Setup Instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Classic Exhibits SYK-1007 Setup Instructions
-
-
-
-
-
-
-
-
-