Kiddicare polka party baby User manual

Brand: Kiddicare

Model: polka party baby

Type: User manual

Kiddicare polka party baby is a baby walker intended for children who can sit unaided, approximately from 6 months. It features a height-adjustable seat, a detachable toy bar, and friction strips for added safety. The walker is easy to assemble and clean. It is important to ensure that the child's feet reach the floor and to never leave the child unattended while using the walker. Please refer to the instruction manual for detailed safety warnings and usage instructions.

WARNING: Keep for future reference

Read these instructions carefully before use

Instruction Leaﬂet

general care

polka party baby

IMPORTANT KEEP FOR FUTURE REFERENCE!

Imported for K by: The Red Kite Baby Co Ltd.

35 Lavenham Road, Beeches Industrial Estate,

Yate, Bristol, BS37 5QX

This baby walking frame is intended to be used by children who can sit unaided,

approximately from 6 months. It is not intended for children weighing more than 12kg.

Complies with BS EN 1273 : 2005 Customer Care: [email protected]

The correct use and maintenance

of this walker is essential.

Ensure that both of the child’s feet

reach the ﬂoor.

Do not use excessive force when

adjusting the walker.

Always store the walker in a dry

place.

Individual toys on the toy bar are

not replaceable.

Do not alter the toy bar by adding,

toys or cutting existing ones away,

this could be dangerous.

Cleaning

The seat unit may be spot cleaned

byusing a sponge with a mild soap

and warm water solution. Leave to

dry in a ventilated area away from

direct sunlight. Do not dry clean,

machine wash, bleach or tumble

dry.

Metal parts may be cleaned with a

damp cloth. Always wipe dry.

Clean plastic parts with a mild soap

and warm water solution.

Avoid leaving the walker in direct

sunlight for prolonged periods of

time as this may cause fabrics to

fade.

Maintenance

Check that nothing is loose or

broken and that no sharp edges

have been exposed. Replace any

damaged parts immediately.

Inspect all studs, nuts and screws

for tightness. Check the seat

attachment points, ensure they are

secured.

Do not use replacement parts

other than those approved by the

manufacturer or distributor. Failure

to do this may invalidate your

warranty.

Removing the friction strips will

invalidate your warranty.

Never use this product without the

friction strips.

Safety warnings

Warning Never leave the child

unattended .

Warning your childs safety is yoiur

responsibility

Prevent access to stairs, steps,and

uneven surfaces.

Guard all ﬁres, heating cooking

appliances.

Remove hot liquids, electrical

ﬂexes and other hazards from

reach.

Prevent collisions with glass in

doors windows and furniture.

Never use the baby walking frame

if ant components are broken or

missing.

This baby walking frame should be

used only for short periods of time

(e.g. 20 min)

WALKER

assembly

Parts list

A 1 x seat unit

B 2 x front wheels

C 2 x rear wheels

D 1 x toybar

E 6 x friction strips

F 1 x frame

Wheel assembly

Turn the frame upside down and

push the wheels into the

corresponding holes in the base.

Ensure the wheels are fully inserted.

Fig 1

Friction strip assembly

Align the stems of the friction strips

with the corresponding holes in the

base and push fully in. Please note

that the outside stems are different

sizes. Make sure the thinner stem is

pointing towards the base. Fig 2

Seat assembly (back)

Turn the frame back onto the wheels

and lift the top tray up until it clicks

into place. Fig 3

Thread the straps onto the back of

the seat unit through the slots in the

tray recess. Fig 4

Now, from the underside, pull the

straps and the buckles completely

through and pivot the buckle 90° so

it lies ﬂat against the underside of

the tray. Fig 5

Seat assembly (front)

To secure the front of the seat, slot

the right hand pin into the front of

the seat, then the left hand pin. Push

inwards and towards the right.Fig 6

The central pin should automatically

locate into the hole. Now push the

pins inwards and downwards to

secure all three pins.Fig 7

IMPORTANT! Please refer to the

“Additional Safety Checks” leaﬂet

supplied before using the walker for

the ﬁrst time.

Toy bar assembly

Clip the toy bar onto the edges of

the top tray where the ridges are.

Fig 8

Height adjustment

Turn the red height adjustment lever

90° anticlockwise with your thumb

and index ﬁnger.Fig 9a + b

Pull your ﬁnger towards you in a

downward motion. This will release

the lock and enable you to choose

one of the different height

positions.Fig 9c

NOTE

- Always remove your child

from the walker before trying adjust

the height.

TIP-You may ﬁnd it easier to place

your feet on the walker base when

adjusting the height.

FFig 6

Fig 7

Fig 8

Fig 9a

Fig 9b Fig 9c

Fig 2

Fig 1

Fig 3

Fig 4

Fig 5

Kiddicare polka party baby User manual

Brand: Kiddicare

Model: polka party baby

Type: User manual

Download PDF

report

Kiddicare polka party baby User manual

Kiddicare polka party baby User manual

Other documents